Water‐soluble acrylamide copolymers. VI. Preparation and characterization of poly[N,N‐dimethylacrylamide‐co‐acrylamide] and control polyacrylamides

This article describes the first of a new series of preparations of water‐soluble acrylamide, substituted acrylamide copolymers and related homopolymers. Objectives of this work were to measure the progressive influence on the hydrodynamic volume and other properties contributed by incorporation of N,N‐dimethylacrylamide (DMA) into a series of high molecular weight acrylamide copolymers. Traditional photoacoustic Fourier transform infrared, ¹³C NMR, and elemental analysis were used for primary characterization. A series of tests using viscometric, gel permeation, chromatographic, and multiangle laser light scattering methods were then used to measure the hydrodynamic volumes of the products. Copolymers incorporating 14, 23, 43, and 63 mol percent DMA with molecular weights of greater than 5 × 10⁶ g/mol were obtained with yields of better than 70%. Aqueous solutions of these polymers showed little or no decrease in radii of gyration or intrinsic viscosity when low concentrations of sodium chloride were added, in contrast to its effect on solutions of polyacrylamide itself. For the copolymers, higher values were obtained for < r_g > and [η], than were observed for acrylamide homopolymers of comparable molecular weight. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3128–3145, 2000     

Water‐soluble acrylamide copolymers. VIII. Preparation and characterization of polyacrylamide‐co‐N‐t‐butylacrylamide

The preparation of a series of copolymers of N‐t‐butylacrylamide (NTBAM) with acrylamide (AM) is reported. The insolubility of NTBAM in water led to the testing of methanol, t‐butanol, and mixtures of these solvents with water to obtain effective copolymerization. Several of these polymerizations produced nonhomogeneous product mixtures. Samples of the components were separated and characterized by photoacoustic Fourier transform infrared spectroscopy and ¹³C NMR spectroscopy. Hydrodynamic volumes of the products were obtained from solution‐viscosity measurements, gel permeation chromatography, and multi‐angle laser light scattering methods. The NTBAM‐co‐AM copolymers had degrees of polymerization and molecular weights in the 4.1–5.9 × 10⁴ monomer units and 3.25–4.5 × 10⁶ g/mol range, respectively. They contained from 15 to 36 mol % NTBAM. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 1960–1977, 2001     

Synthesis,characterization, and properties of copolymer of acrylamide and complex pseudorotaxane monomer consisting of cucurbit[6]uril with butyl ammonium methacrylate

The novel copolymers of acrylamide (AM) with complex pseudorotaxane monomer (BAMACB) of butyl ammonium methacrylate (BAMA) and cucurbit[6]uril (CB[6]) were prepared via free‐radical polymerization in aqueous solution. The copolymers containing pseudorotaxane (PAM/BAMACB) were characterized by ¹H‐NMR, FTIR, elemental analysis, TGA, and DSC. The glass transition temperature (T_g) of the copolymer PAM/BAMACB are higher than that of the copolymer of acrylamide and butyl ammonium methacrylate (PAM/BAMA) because of the enhanced rigidity and the bulky steric hindrance of BAMACB side chain in PAM/BAMACB. The molecular weights of copolymer PAM/BAMACB were obtained via static light scattering. The hydrodynamic radii of coils or aggregates were investigated by dynamic light scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5999–6008, 2008     

Water‐soluble acrylamide copolymers. IX. Preparation and characterization of the cationic derivatives of poly(acrylamide‐co‐n,n‐dimethylacrylamide), poly(acrylamide‐co‐methacrylamide), and poly(acrylamide‐co‐n‐t‐butylacrylamide)

This article extends the preparative details of a series of nonionic copolymers of acrylamide with N,N‐dimethylacrylamide, methacrylamide, and N‐t‐butylacrylamide to the synthesis of cationic derivatives of these new copolymers. The described procedures gave products with cationicities of 14–26 mol %. We measured the mean squared radii of gyration and intrinsic viscosities of aqueous solutions of these products at several different pHs and NaCl concentrations to compare these values with those determined for the nonionic precursors and related commercial cationic polymers. Because the molecular weights of the examples measured varied widely, it was difficult to establish definite trends. However, the large values obtained for the mean squared radii of gyration and intrinsic viscosities, relative to the nonionic precursors of these polymers, demonstrated that the charged groups had a qualitatively greater effect on polymer extension than the nonpolar bulky groups. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2525–2535, 2001     

End‐group fidelity in nitroxide‐mediated living free‐radical polymerizations

In this study, new nitroxides based on the 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐oxy skeleton were used to examine chain‐end control during the preparation of polystyrene and poly(t‐butyl acrylate) under living free‐radical conditions. Alkoxyamine‐based initiators with a chromophore attached to either the initiating fragment or the mediating nitroxide fragment were prepared, and the extent of the incorporation of the chromophores at either the initiating end or the propagating chain end was determined. In contrast to 2,2,6,6‐tetramethyl piperidinoxy (TEMPO), the incorporation of the initiating and terminating fragment into the polymer chain was extremely high. For both poly(t‐butyl acrylate) and polystyrene with molecular weights less than or equal to 70,000, incorporations at the initiating end of greater than 97% were observed. At the terminating chain end, incorporations of greater than 95% were obtained for molecular weights less than or equal to 50,000. The level of incorporation tended to decrease slightly at higher molecular weights because of the loss of the alkoxyamine propagating unit, which had important consequences for block copolymer formation. These results clearly show that these new α‐H nitroxides could control the polymerization of vinyl monomers such as styrene and t‐butyl acrylate to an extremely high degree, comparable to anionic and atom transfer radical polymerization procedures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4749–4763, 2000     

Polyampholyte terpolymers of amphoteric,amino acid‐based monomers with acrylamide and (3‐acrylamidopropyl)trimethyl ammonium chloride

Low‐charge‐density amphoteric copolymers and terpolymers composed of acrylamide, (3‐acrylamidopropyl)trimethyl ammonium chloride, and the amino acid derived monomers (e.g., N‐acryloyl valine, N‐acryloyl alanine, and N‐acryloyl aspartate) were prepared via free‐radical polymerization in aqueous media to yield terpolymers with random charge distributions and homogeneous compositions. Sodium formate (NaOOCH) was employed as a chain transfer agent during the polymerization to suppress gel effects and broadening of the molecular weight distribution. Terpolymer compositions were determined by ¹³C and ¹H NMR spectroscopy. Terpolymer molecular weights and polydispersity indices were obtained via size exclusion chromatography/multi‐angle laser light scattering, and hydrodynamic diameter values were obtained via dynamic light scattering. The solution properties of low‐charge‐density amphoteric copolymers and terpolymers have been studied as a function of solution pH, ionic strength, and polymer concentration. The low‐charge‐density terpolymers display excellent solubility in deionized (DI) water with no phase separation. The charge‐balanced terpolymers exhibit antipolyelectrolyte behavior at pH values ≥(6.5 ± 0.2). As solution pH is decreased, these charge‐balanced terpolymers become increasingly cationic because of the protonation of the anionic repeat units. Charge‐imbalanced terpolymers generally demonstrate polyelectrolyte behavior, although the effects of intramolecular electrostatic interactions (e.g., polyampholyte effects) on the hydrodynamic volume are evident at certain values of solution pH and salt concentration. The aqueous solution behavior (i.e., globule‐to‐coil transition at the isoelectric point in the presence of salt and globule elongation with increasing charge asymmetry) of the terpolymers in the dilute regime correlates well with that predicted by the polyampholyte solution theories of Dobrynin and Rubinstein as well as Kantor and Kardar. Examination of comonomer charge density, hydrogen‐bonding ability, and spacer group (e.g., the moiety separating the ionic group from the polymer chain) indicates that conformational restrictions of the amino acid comonomers result in increased chain stiffness and higher solution viscosities in DI water and brine solutions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4479–4493, 2006     

Polytetrahydrofuran amphiphilic networks. I. Synthesis and characterization of polytetrahydrofuran acrylate ditelechelic and polyacrylamide‐l‐polytetrahydrofuran networks

A series of novel amphiphilic polyacrylamide‐l‐polytetrahydrofuran (PAm‐l‐PTHF) networks were prepared by the free‐radical copolymerization of hydrophobic ditelechelic polytetrahydrofuran acrylate (PTHFDA) with hydrophilic acrylamide. PTHFDA was synthesized by acrylation of the corresponding hydroxycapped PTHF with acrylic acid in cyclohexane. After acrylation, there was no significant difference in the molecular weights and molecular weight distributions between the original PTHF and the resulting PTHFDA. Network structures and compositions were characterized by elemental analyses, Fourier transform infrared, differential scanning calorimetry, scanning electron microscopy, and swelling data. The networks can swell both in organic solvents and in water, which indicates that they are amphiphilic. The swelling of the networks in different solvents is composition‐dependent. According to differential scanning calorimetry, scanning electron microscopy, and swelling tests, the networks have a microphase‐separated and bicontinuous morphology. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3812–3820, 2000     

Novel thermoresponsive fluorinated double‐hydrophilic poly{[N‐(2,2‐difluoroethyl)acrylamide]‐b‐[N‐(2‐fluoroethyl)acrylamide]} block copolymers

Novel thermoresponsive double‐hydrophilic fluorinated block copolymers were successfully synthesized by reversible addition‐fragmentation chain transfer (RAFT) polymerization. Poly[N‐(2,2‐difluoroethyl)acrylamide] (P2F) was synthesized via RAFT polymerization of N‐(2,2‐difluoroethyl)acrylamide (M2F) using 2‐dodecylsulfanylthiocarbonylsulfanyl‐2‐methylpropionic acid (DMP) as the chain transfer agent (CTA) and 2,2′‐azobisisobutyronitrile (AIBN) as the initiator. The resulting P2F macroCTA was further chain extended with N‐(2‐fluoroethyl)acrylamide (M1F) to yield poly{[N‐(2,2‐difluoroethyl)acrylamide]‐b‐[N‐(2‐fluoroethyl)acrylamide]} (P2F‐b‐P1F) block copolymers with different lengths of the P1F block. Molecular weight and molecular weight distribution were determined by gel permeation chromatography. The average molecular weight (M_n) of the resulting polymers ranged from 2.9 × 10⁴ to 5.8 × 10⁴ depending on the length of the P1F block. The molecular weight distribution was low (M_w/M_n = 1.11–1.19). Turbidimetry by UV‐Visble (UV‐Vis) spectroscopy, dynamic light scattering, and in situ temperature‐dependent ¹H NMR measurements demonstrated that the P2F block underwent a thermal transition from hydrophilic to hydrophobic, which in turn induced self‐assembly from unimers to aggregates. Transmission electron microscopy studies demonstrated that polymeric aggregates formed from an aqueous solution of P2F‐b‐P1F at 60 °C were disrupted by cooling down to 20 °C and regenerated by heating to 60 °C. Temperature‐triggered release of a model hydrophobic drug, coumarin 102, was also demonstrated. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Poly[N‐isopropyl acrylamide]‐co‐polyurethane copolymers for controlled release of urea

A novel block copolymer of poly[N‐isopropyl acrylamide]‐co‐polyurethane was designed, synthesized, and applied as controlled release fertilizer coating. Structural confirmation of the copolymer was performed using FTIR and ¹H‐NMR spectra and elemental analysis. The coating process consists essentially of immersing urea granules in molten polymer and removing the coated urea from the melt by centrifugal action. The morphology of the coated urea was studied using scanning electron microscope (SEM). The polymer coat of the urea granules was found to swell in water forming pores and enabling the release of urea. The urea released from the granule, monitored using a mass spectroscopy technique, was found to be governed by pH of the aqueous medium. The study anticipates development of a beneficiary fertilizer coat in terms of improving controlled release over a period of time which can be tailored by soil temperature, pH and moisture. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3236–3243, 2010     

The synthesis of poly[6,8‐dioxabicyclo[3.2.1]octane‐b‐(ethylene glycol)‐b‐6,8‐dioxabicyclo[3.2.1]octane] by controlled cationic ring‐opening polymerization

The triblock copolymer poly[6,8‐dioxabicyclo[3.2.1]octane‐b‐(ethylene glycol)‐b‐6,8‐dioxabicyclo[3.2.1]octane] was prepared by the controlled cationic ring‐opening polymerization of 6,8‐dioxabicyclo[3.2.1]octane (6,8‐DBO) from a macroinitiator. The macroinitiator, poly(ethylene glycol) (PEG) di(1‐chloroethyl ether), was prepared via the addition of HCl to PEG divinyl ether and was characterized with ¹³C NMR, ¹H NMR, and gel permeation chromatography (GPC). Upon preparation, a small fraction of the chain ends underwent a cyclization reaction to form inactive chain ends. When the macroinitiator was used in polymerizations of 6,8‐DBO with ZnI₂ as an activator, linear kinetic plots were observed, a linear increase in the copolymer molecular weight with conversion was seen, and the molecular weight distributions of the copolymer samples remained constant at about 1.40. Confirmation of the triblock structure of the final product was obtained with ¹H NMR spectra, ¹³C DEPT spectra, and GPC chromatograms. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4081–4087, 2000     

Microwave‐assisted nitroxide‐mediated polymerization for water‐soluble homopolymers and block copolymers synthesis in homogeneous aqueous solution

We performed a critical reinvestigation of microwave enhancement of nitroxide‐mediated polymerization (NMP) of acrylamide (AM) in aqueous media in the dynamic (DYN) mode with a combination of a conventional hydrosoluble radical initiator and a β‐phosphonylated nitroxide (SG1). Based on the results of our previous work, a complementary series of polymerization reactions was carried out between 130 and 160 °C using only the DYN mode to ascertain the existence of a microwave effect. The polymer conversion (p), molar masses, polydispersity index, and viscosity of each sample were measured. The temperature was monitored inside and outside of the vessel using an optical fiber sensor and an IR sensor, respectively. Microwave enhancement of polymerization, temperature control and viscosity of the reaction media were closely related. We also furthered the field of hydrophilic AB diblock copolymer synthesis using a tertiary SG1‐based macroalkoxyamine and directly synthesized both poly(acrylamide‐b‐sodium 2‐acrylamido‐2‐methylpropanesulfonate), a neutral‐b‐anionic diblock copolymer, and poly(acrylamide‐b‐3‐dimethyl(methacrylamidopropyl)ammonium propanesulfonate), a neutral‐b‐zwitterionic diblock copolymer, in homogeneous aqueous media. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Block and star block copolymers by mechanism transformation. II. Synthesis of poly(DOP‐b‐St) by combination of ATRP and CROP

Styrene underwent the ATRP process using an asymmetric difunctional initiator, 2‐hydroxylethyl 2′‐bromobutyrate in combination with CuBr and 2,2′‐bipyridine (bpy). Polystyrene with hydroxyl and bromine groups at each end of the polymer (HO‐PSt‐Br) was obtained, and used as a chain‐transfer agent in the cationic ring‐opening polymerization of 1,3‐dioxepane with triflic acid as initiator. The structures of the polymerization products were analyzed by ¹H NMR and GPC analyses, indicating the formation of block copolymer. The molecular weight distribution of the block copolymer was relatively narrow and the molecular weight of the polyDOP block was high. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 436–443, 2000     

Flexibilized styrene‐N‐substituted maleimide copolymers. I. Multiblock copolymers prepared from styrene‐maleimide telechelics and polytetrahydrofuran

Telechelic copolymers of styrene and different N‐substituted‐maleimides (SMIs) with a molecular weight of 2000–8000 g/mol were synthesized using the starved‐feed‐reactor technique and were nearly bifunctional when the monomer feed had a high styrene concentration. The COOH‐terminated rigid SMI blocks were polycondensated with OH‐terminated poly(tetrahydrofuran) (PTHF) blocks, with a molecular weight of 250–1000 g/mol, which are the flexible parts in the generated homogeneous multiblock copolymer. The entanglement density, which is closely related to the toughness of materials, increased in these flexible SMI copolymers (ν_e = 5.2 · 10²⁵ m⁻³) compared to the unflexibilized ones (ν_e = 2.4 · 10²⁵ m⁻³). The glass transition temperature of these flexibilized, single‐phase multiblock copolymers was still high enough to qualify them as engineering plastics. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3550–3557, 2000     

Stimuli‐responsive ampholytic terpolymers of N‐acryloyl‐valine,acrylamide, and (3‐acrylamidopropyl)trimethylammonium chloride: Synthesis,characterization, and solution properties

Low‐charge density ampholytic terpolymers composed of acrylamide (AM), (3‐acrylamidopropyl)trimethyl ammonium chloride (APTAC), and N‐acryloyl‐valine were prepared via free‐radical polymerization in 0.5 M NaCl to yield terpolymers with random charge distributions. Sodium formate (NaOOCH) was employed as a chain transfer agent during the polymerization to suppress gel effects and broadening of the molecular weight distribution (MWD). Terpolymer compositions were determined by ¹³C NMR spectroscopy. Terpolymer molecular weights (MWs) and polydispersity indices (PDIs) were obtained via size exclusion chromatography/multi‐angle laser light scattering (SEC‐MALLS). Intrinsic viscosity values determined from SEC‐MALLS data using the Flory–Fox relationship were compared with those determined by low‐shear dilute solution viscometry and found to be in good agreement. SEC‐MALLS experiments allowed examination of radius of gyration‐MW (R_g‐M) relationships and the Mark‐Houwink‐Sakurada intrinsic viscosity‐MW ([η]‐M) relationships for terpolymers. The R_g‐M and [η]‐M relationships indicated little or no excluded volume effects under SEC conditions indicating that the terpolymers were in near theta conditions in an aqueous buffer solution. Potentiometric titration experiments were performed in deionized (DI) water. These studies revealed that the apparent pK_a of the AMVALTAC terpolymers increases with increasing VAL content. The solution properties of low‐charge density ampholytic terpolymers have been studied as functions of solution pH, ionic strength, and polymer concentration. The charge‐balanced terpolymers exhibit polyampholyte behavior at pH values ≥ 6.5. As solution pH is decreased, these charge‐balanced terpolymers become increasingly cationic due to the protonation of the VAL repeat units. Charge‐imbalanced terpolymers generally exhibit polyelectrolyte behavior, although the effects of intramolecular electrostatic interactions (e.g., polyampholyte effects) on the hydrodynamic volume are evident at certain values of solution pH and salt concentration. The solution behavior of the terpolymers in the dilute regime correlates well with that predicted by various polyampholyte solution theories. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3125–3139, 2006     

Thermosensitive t‐PLA‐b‐PNIPAAm tri‐armed star block copolymer nanoscale micelles for camptothecin drug release

Thermosensitive polylactide‐block‐poly(N‐isopropylacrylamide) (t‐PLA‐b‐PNIPAAm) tri‐armed star block copolymers were synthesized by atom transfer radical polymerization (ATRP) of monomer NIPAAm using t‐PLA‐Cl as macroinitiator. The synthesis of t‐PLA‐Cl was accomplished by esterification of star polylactides (t‐PLA) with 2‐chloropropionyl chloride using trimethylolpropane as a center molecule. FT‐IR, ¹H NMR, and GPC analyses confirmed that the t‐PLA‐b‐PNIPAAm star block copolymers had well‐defined structure and controlled molecular weights. The block copolymers could form core‐shell micelle nanoparticles due to their hydrophilic‐hydrophobic trait in aqueous media, and the critical micelle concentrations (CMC) were from 6.7 to 32.9 mg L^?1, depending on the system composition. The as‐prepared micelle nanoparticles showed reversible phase changes in transmittance with temperature: transparent below low critical solution temperature (LCST) and opaque above the LCST. Transmission electron microscopy (TEM) observations revealed that the micelle nanoparticles were spherical in shape with core‐shell structure. The hydrodynamic diameters of the micelle nanoparticles depended on copolymer compositions, micelle concentrations and media. MTT assays were conducted to evaluate cytotoxicity of the camptothecin‐loaded copolymer micelles. Camptothecin drug release studies showed that the copolymer micelles exhibited thermo‐triggered targeting drug release behavior, and thus had potential application values in drug controlled delivery. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4429–4439     

Radical ring‐opening copolymerization behavior of vinyloxirane: Synthesis of copolymer from 2‐isopropenyl‐3‐phenyloxirane and styrene and its functionalization

The radical ring‐opening copolymerization of 2‐isopropenyl‐3‐phenyloxirane (1) with styrene (St) was examined to obtain the copolymer [copoly(1‐St)] with a vinyl ether moiety in the main chain. The copolymers were obtained in moderate yields by copolymerization in various feed ratios of 1 and St over 120 °C; the number‐average molecular weights (M_n) were estimated to be 1800–4200 by gel permeation chromatography analysis. The ratio of the vinyl ether and St units of copoly(1‐St) was estimated with the ¹H NMR spectra and varied from 1/7 to 1/14 according to the initial feed ratio of 1 and St. The haloalkoxylation of copoly(1‐St) with ethylene glycol in the presence of N‐chlorosuccinimide produced a new copolymer with alcohol groups and chlorine atoms in the side group in a high yield. The M_n value of the haloalkoxylated polymer was almost the same as that of the starting copoly(1‐St). The incorporated halogen was determined by elemental analysis. The analytical result indicated that over 88% of the vinyl ether groups participated in the haloalkoxylation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3729–3735, 2000     

Synthesis and characterization of poly(DTC‐b‐PEG‐b‐DTC) triblock and poly(TMC‐b‐DTC‐b‐PEG‐b‐DTC‐b‐TMC) pentablock copolymers and kinetics of the polymerization

Dihydroxyl capped biodegradable poly(DTC‐b‐PEG‐b‐DTC) (BCB) triblock copolymer and poly(TMC‐b‐DTC‐b‐PEG‐b‐DTC‐b‐TMC) (ABCBA) pentablock copolymer have been synthesized by PEG and BCB copolymer as macroinitiator in the presence of yttrium tris(2,6‐di‐tert‐butyl‐4‐methylphenolate). The copolymers without random segments have been thoroughly characterized by ¹H, ¹³C‐NMR, SEC, and DSC. Molecular weights of the obtained copolymers are dependent on the amount of PEGs and coincide with the theoretical values. The exchange reaction of yttrium alkoxide and hydroxyl end group is essential for controlling the products' molecular weight. Their thermal behaviors are relevant to the chain lengths of PEG and PDTC segments. The Monte Carlo method has been developed to estimate the chain propagation constant and exchange reaction constant. In average, one exchange reaction will occur after approximately six monomer molecules insert into the growing chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1787–1796, 2005     

Surfactant‐free synthesis of amphiphilic diblock copolymer in aqueous phase by a self‐stability process

Amphiphilic polymeric particles with hydrophobic cores and hydrophilic shells were prepared via living radical emulsion polymerization of styrene using a water‐soluble poly(acrylamide)‐based macro‐RAFT agent in aqueous solution in the absence of any surfactants. Firstly, the homopolymerization of acrylamide (AM) was carried out in aqueous phase by reversible addition‐fragmentation chain transfer radical polymerization (RAFT) using a trithiocarbonate as a chain transfer agent. Then the PAM‐based macro‐RAFT agent has been used as a water‐soluble macromolecular chain transfer agent in the batch emulsion polymerization of Styrene (St) free of surfactants. The RAFT controlled growth of hydrophobic block led to the formation of well‐defined poly(acrylamide)‐copolystyrene amphiphilic copolymer, which was able to work as a polymeric stabilizer (self‐stability). Finally, very stable latex was prepared, having no visible phase separation for several months. FTIR and ¹H‐NMR measurements showed that the product was the block copolymer PAM‐co‐PS in the form of stable latex. Atomic force microscope (AFM), transmission electron microscope (TEM), and dynamic light scattering (DLS) studies indicated that the nanoparticles have a narrow particle size distribution and the average particle hydrodynamic radius was kept in the diameter of 58 nm. Core‐shell structure of the copolymer was also recorded by TEM. The mechanism of the self‐stability of polymer particles during the polymerization in the absence of surfactants was studied. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3098–3107, 2008     

Syntheses,antitumor activities,and antiangiogenesis of exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidoethanoyl‐ 5‐fluorouracil and its polymers

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidoethanoyl‐5‐fluorouracil (ETFU), was synthesized by the reaction of exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidoethanoyl chloride (ETPC) and 5‐fluorouracil (5‐FU). The homopolymer of ETFU and its copolymers with acrylic acid (AA) and vinyl acetate (VAc) were prepared via photopolymerizations with 2,2‐dimethoxy‐2‐phenylacetophenone at 25 °C for 48 h. The structures of the synthesized monomer and polymers were identified by Fourier transform infrared, ¹H NMR, and ¹³C NMR spectroscopy and elemental analysis. The ETFU contents in poly(ETFU‐co‐AA) and poly(ETFU‐co‐VAc) were 26 mol % and 26 mol %, respectively. The number‐average molecular weights of the polymers, as determined by gel permeation chromatography, ranged from 5600 to 17,000. The in vitro cytotoxicities of 5‐FU and the synthesized samples against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines increased in the following order: ETFU > 5‐FU > poly(ETFU‐co‐AA) > poly(ETFU) > poly(ETFU‐co‐VAc). The in vivo antitumor activities of the polymers against Balb/C mice bearing the sarcoma 180 tumor cells were greater than those of 5‐FU at all doses tested. The inhibitions of the samples for SV40 DNA replication and antiangiogenesis were much greater than the inhibition of the control. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4272–4281, 2000     

Polar,functionalized diene‐based materials. V. Free‐radical polymerization of 2‐[(N‐benzyl‐n‐methylamino)methyl]‐1,3‐butadiene and copolymerization with styrene

2‐[(N‐Benzyl‐N‐methylamino)methyl]‐1,3‐butadiene (BMAMBD), the first asymmetric tertiary amino‐containing diene‐based monomer, was synthesized by sulfone chemistry and a nickel‐catalyzed Grignard coupling reaction in high purity and good yield. The bulk and solution free‐radical polymerizations of this monomer were studied. Traditional bulk free‐radical polymerization kinetics were observed, giving polymers with 〈M_n〉 values of 21 × 10³ to 48 × 10³ g/mol (where M_n is the number‐average molecular weight) and polydispersity indices near 1.5. In solution polymerization, polymers with higher molecular weights were obtained in cyclohexane than in tetrahydrofuran (THF) because of the higher chain transfer to the solvent. The chain‐transfer constants calculated for cyclohexane and THF were 1.97 × 10^?3 and 5.77 × 10^?3, respectively. To further tailor polymer properties, we also completed copolymerization studies with styrene. Kinetic studies showed that BMAMBD incorporated into the polymer chain at a faster rate than styrene. With the Mayo–Lewis equation, the monomer reactivity ratios of BMAMBD and styrene at 75 °C were determined to be 2.6 ± 0.3 and 0.28 ± 0.02, respectively. Altering the composition of BMAMBD in the copolymer from 17 to 93% caused the glass‐transition temperature of the resulting copolymer to decrease from 64 to ?7 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3227–3238, 2001