Healable dual organic–inorganic crosslinked sol–gel based polymers: Crosslinking density and tetrasulfide content effect

In this article, the first generation of healable sol–gel based polymers is reported. A dual organic–inorganic crosslinked network is developed containing non‐reversible crosslinks and reversible (tetrasulfide) groups. The designed polymer architecture allows thermally induced mesoscale flow leading to damage closure followed by interfacial strength restoration due to reformation of the reversible groups. While the reversible bonds are responsible for the flow and the interface restoration, the irreversible crosslinks control the required mechanical integrity during the healing process. The temperature dependent gap closure kinetics is strongly affected by the crosslinking density and tetrasulfide content. Raman spectroscopy is used to explain the gap closure kinetics in air and dry nitrogen. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1953–1961     

Electron spin resonance study on chemical crosslinking reaction mechanisms of polyethylene using a chemical agent. V. Comparison with polypropylene and ethylene‐propylene copolymer

We studied the chemical reaction process of polypropylene (PP), ethylene‐propylene copolymer (EPM), and ethylene‐propylene‐diene copolymer (EPDM) crosslinking induced by dicumyl peroxide (DCP) using electron spin resonance (ESR). Free radicals appeared at an elevated temperature of around 120 °C and the behavior and kinetics of the reaction process were observed at 180 °C. The radical species detected in PP were alkyl type radicals, formed by the abstraction of hydrogen atoms from the tertiary carbon of polymer chains. For EPDM containing a diene component, the radicals were trapped at double bonds in this diene component to form allyl radicals. The resolutions of these spectra were extremely clear; hence, isotropic spectra of these polymer radicals were obtained. We measured the ESR at high temperatures and confirmed that the process of crosslinking induced by DCP was a free radical reaction. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3383–3389, 2000     

Semicrystalline blends of polyethylene and isotactic polypropylene: Improving mechanical performance by enhancing the interfacial structure

The low‐temperature mechanical behavior of semicrystalline polymer blends is investigated. Isotactic polypropylene (iPP) is blended with both Zeigler–Natta polyethylene (PE) and metallocene PE. Transmission electron microscopy (TEM) on failed tensile bars reveals that the predominate failure mode in the Zeigler–Natta blend is interfacial, while that in the metallocene blend is failure of the iPP matrix. The observed change in failure mode is accompanied by a 40% increase in both tensile toughness and elongation at −10 °C. We argue that crystallite anchoring of interfacially entangled chains is responsible for this dramatic property improvement in the metallocene blend. The interfacial width between PE and iPP melts is approximately 40 Å, allowing significant interfacial entanglement in both blends. TEM micrographs illustrate that the segregation of low molecular weight amorphous material in the Zeigler–Natta blend reduces the number and quality of crystallite anchors as compared with the metallocene blend. The contribution of anchored interfacial structure was further explored by introducing a block copolymer at the PE/iPP interface in the metallocene blend. Small‐angle X‐ray scattering (SAXS) experiments show the block copolymer dilutes the number of crystalline anchors, decoupling the interface. Increasing the interfacial coverage of the block copolymer reduces the number of anchored interfacial chains. At 2% block copolymer loading, the low‐temperature failure mode of the metallocene blend changes from iPP failure to interfacial failure, reducing the blend toughness and elongation to that of the Zeigler–Natta blend. This work demonstrates that anchored interfacial entanglements are a critical factor in designing semicrystalline blends with improved low‐temperature properties. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 108–121, 2000     

Inhomogeneity control in polymer gels

Inhomogeneities, that is, nonrelaxing frozen concentration fluctuations, are inevitably present in polymer gels because they are introduced during the crosslinking of the constituent polymer chains in a solvent. Therefore, inhomogeneities increase as the number of crosslinks increases in a gel. The ionization of polymer gels is one of the methods used to suppress inhomogeneities. However, because crosslinking also means a freezing‐in of the conformation and topology of polymer chains in a solvent according to the chemistry of crosslinking, inhomogeneity control is quite sophisticated. In this article, we discuss the relationship between the inhomogeneities and the molecular/environmental parameters of polymer gels, such as the polymer concentration, the degree of crosslinking, the degree of ionization, and the interaction parameter, by considering the memory effect of gels. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 617–628, 2005     

Reinforcement effect of MAA on nano‐CaCo3‐filled EPDM vulcanizates and possible mechanism

Methacrylic acid (MAA) was used as in situ surface modifier to improve the interface interaction between nano‐CaCO₃ particle and ethylene–propylene–diene monomer (EPDM) matrix, and hence the mechanical properties of nano‐CaCO₃‐filled EPDM vulcanizates. The results showed that the incorporation of MAA improved the filler–matrix interaction, which was proved by Fourier transformation infrared spectrometer (FTIR), Kraus equation, crosslink density determination, and scanning electron microscope (SEM). The formation of carboxylate and the participation of MAA in the crosslinking of EPDM indicated the strong filler–matrix interaction from the aspect of chemical reaction. The results of Kraus equation showed that the presence of MAA enhanced the reinforcement extent of nano‐CaCO₃ on EPDM vulcanizates. Crosslink density determination proved the formation of the ionic crosslinks in EPDM vulcanizates with the existence of MAA. The filler particles on tensile fracture were embedded in the matrix and could not be observed obviously, indicating that a strong interfacial interaction between the filler and the matrix had been achieved with the incorporation of MAA. Meanwhile, the presence of MAA remarkably increased the modulus and tensile strength of the vulcanizates, without negative effect on the high elongation at break. Furthermore, the ionic bond was thought to be formed only on filler surface because of the absolute deficiency of MAA, which resulted in the possible structure where filler particles were considered as crosslink points. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1226–1236, 2006     

Crosslinking of chlorine‐containing polymers by dicyclopentadiene dicarboxylic salts

Alkali‐ and alkali‐earth‐metal salts of dicyclopentadiene dicarboxylic acid (DCPDCA) were prepared and employed as crosslinkers for chlorine‐containing polymers such as polychloromethylstyrene (PCMS), chlorinated polypropylene (CPP), polyepichlorohydrin (PECH), and poly(vinyl chloride) (PVC). Thermally reversible covalent crosslinks (i.e.,  DCPD bridges) between polymer chains were generated through esterification between the chlorine–carbon bonds of the polymer and the carboxylic salt groups of the crosslinker. The crosslinking reactivity decreased in the following sequence: K > Na > LiDCPDCA > alkali‐earth‐metal salts of DCPDCA. In addition, PCMS and CPP had higher gelation rates than PECH and PVC. Good flowability at about 195 °C and solubility in maleimide‐containing dichlorobenzene on heating indicated that the crosslinked PCMS and CPP exhibited thermally reversible crosslinking because of dimer/monomer (cyclopentadiene) conversion of  DCPD moieties via reversible Diels–Alder cycloaddition. Samples of PECH and PVC crosslinked by the alkali salts of DCPDCA were insoluble even when heated in maleimide‐containing dichlorobenzene. However, these crosslinked polymers could be dissolved partially after the same treatment when the crosslinker was an alkali‐earth‐metal salt of DCPDCA. Thermal degradation such as dehydrochlorination of the PECH and PVC might have been responsible for uncontrolled crosslinking because these two polymers are known to be thermally unstable. The unreacted COOK, COONa, or COOLi of the crosslinkers might have initiated base‐induced dehydrochlorination when PECH and PVC were heated at high temperatures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 818–825, 2000     

Shell crosslinked polymer assemblies: Nanoscale constructs inspired from biological systems

The general approach involving the organization of polymers into micellar assemblies followed by stabilization through covalent intramicellar crosslinking of the assemblies has emerged as a powerful method for the production of well‐defined nanostructured materials, having an amphiphilic core‐shell morphology. When the covalent crosslinks are limited to the chain segments that compose the polymer micelle shell, then shell crosslinked knedel‐like (SCK) nanostructures result. The shell composition dictates the interactions of the SCKs with external agents, forms a barrier layer over the core domain, and provides robust character to the nanoparticle. Because of the stability that the crosslinked shell provides, the core domain can be of dramatically different compositions and properties—glassy, fluidlike, and crystalline polymer chains have been employed for the core material and the effects that each contributes to the overall nanostructure properties have been examined. Most notably, the shell crosslinks allow for complete removal of the core to generate hollow (solvent‐filled) nanoscale cagelike structures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1397–1407, 2000     

Postgel properties in the statistical crosslinking of heterochains. I. Systems with N types of chains

The heterochain crosslinking model describes nonrandom crosslinking of polymer chains and is an extension of the classical Flory/Stockmayer gelation theory. We consider the postgelation relationship for the system consisting of N types of polymer chains, in which the probability that a crosslink point on an i‐type chain is connected to a j‐type chain is explicitly given by p_ij. The analytical solutions for the weight fraction of the sol, the number‐average and weight‐average molecular weights within the sol fraction, and the crosslinking density within the sol and gel fractions are derived for the systems, with each type of chain conforming to the Schulz–Zimm distribution. Illustrative calculations are shown for the systems consisting of two and three types of chains, and the obtained results agree with those from the Monte Carlo method. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2333–2341, 2000     

Confinement of polystyrene at interfaces: Consequences on chain orientation

The knowledge of the structure and orientation of polymer chains adsorbed at an interface could be of major importance to predict the level of interfacial interactions and adhesion that depend strongly on the properties of the interface formed between the two materials (polymer and substrate) brought into contact. In this work, we were interested to study thin films of atactic polystyrene after adsorption (spin‐coating) on two chemically different substrates (inert and OH‐grafted gold substrates). The main aim is to analyze the resulting anisotropy due to the confinement in a quasi‐bidimensional geometry, as well as to investigate the incidence of the interfacial interactions, potentially established between the polymer and the surface, on the chain organization. Our infrared spectroscopy results allowed us to access the adsorption model of polystyrene chains and to highlight the relation between chain orientation and interfacial acid–base interactions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1268–1276, 2006     

Autohésion des élastomères : Anomalie de comportement de l'EPDM

The mechanisms responsible for the anomalous adhesive behaviour of EPDM elastomer have been elucidated by studying the interfacial strength of two EPDM networks. An extremely slow diffusion could be observed and was attributed to the presence of the branching of EPDM macromolecules associated with a high degree of entanglements. It was shown that diffusion is an essential preliminary step to obtain good interfacial co-crosslinking and hence high final adhesive strength.     

Epoxy‐functionalized,low‐glass‐transition‐temperature latex. II. Interdiffusion versus crosslinking in the presence of a diamine

This article describes the results of experiments examining the competition between the polymer diffusion rate and the crosslinking rate in low‐glass‐transition‐temperature, epoxy‐containing latex films in the presence of a diamine. We examined films formed from donor‐ and acceptor‐labeled poly(butyl acrylate‐co‐methyl methacrylate‐co‐glycidyl methacrylate) copolymer latex and studied the influence of several parameters on the growth rate of gel content and the rate of polymer diffusion. These factors include the molecular weight of the latex polymer, the presence or absence of a diamine crosslinking agent, and the cure protocol. The results were compared to the predictions of a recent theory of the competition between crosslinking and polymer diffusion across interfaces. In the initially formed films, polymer diffusion occurs more rapidly than the chemical reaction rate. Therefore, these films fall into the fast‐diffusion category of this model. In our system (unlike in the model), the latex polymer has a broad distribution of molecular weights and a distribution of diffusivities. The shortest chains contribute to the early time diffusion that we measure. At later stages of our experiment, slower diffusing species contribute to the signal that we measure. The diffusion time decreases substantially, and we observe a crossover to a regime in which the chemical reaction dominates. The increases in chain branching and gel formation bring polymer diffusion to a halt. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4098–4116, 2002     

Effect of the reactivity of a crosslinking agent on the microphase separation in sequential IPNs: A Monte Carlo simulation study

The effects of the reactivity of a crosslinking agent on the microphase‐separated structure of sequential interpenetrating polymer networks are analyzed with a Monte Carlo simulation technique. The simulation results showed that the maximum structure factor decreases with an increasing crosslinking rate. However, the maximum structure factor increases when the crosslinking rate is increased further. This behavior is explained by a competition between the phase separation and the restriction of chain mobility due to the increase in molecular weight. In addition, there exists a chain length where the chain motion is the most restricted when crosslinks are formed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1005–1012, 2000     

Mechanical and thermo‐mechanical studies of double networks based on thermoplastic elastomers

A new approach to prepare and characterize double network elastomeric systems was investigated. A styrene‐ethylene‐co‐butylene‐styrene (SEBS) triblock copolymer system containing physical crosslinks was used to achieve a double network by additional crosslinking using ultra‐violet (UV) light. An ethylene–propylene–diene monomer (EPDM) terpolymer system containing chemical crosslinks was used to achieve a conventional double network using UV crosslinking. Properties from conventional monotonic tensile tests, dynamic mechanical analysis, and thermomechanical properties were investigated. These double network elastomers show a transition between competitive and collaborative behavior in their mechanical properties and lower coefficients of thermal expansion arising from a competition of the networks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 778–789, 2010     

Side‐chain conformational changes during the thermoshrinking process: γ‐Ray polymerization and spectroscopic study of uncrosslinked poly(methacryloyl‐Ala‐OMe)

Poly(methacryloyl‐L ‐alanine‐methyl ester) (1) has an optically active side chain and consists of thermoshrinking hydrogels upon crosslinking. We synthesized an uncrosslinked polymer of 1 by the γ‐ray polymerization method. For the prepared polymer, variable‐temperature circular dichroism (CD) and ¹H NMR spectra were studied, and we found conformational changes in the optically active side chains during the thermally induced phase transition. Intense CD spectra reveal ordered conformation in the side chain of 1 below the phase transition temperature (∼28 °C). A well‐resolved ¹H NMR spectrum of 1 at 0 °C shows that the conformational angles in the polymer side chain are fixed at low‐energy minima. With increasing temperature, the frozen side chain starts rotating vigorously and takes an unordered orientation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2671–2677, 2000     

In-situ Enhanced Toughening of Poly(ethylene terephthalate)/elastomer Blends via Gamma-Ray Radiation at Presence of Trimethylolpropane Triacrylate

Gamma-ray radiation has always been a convenient and effective way to modify the interfacial properties in polymer blends. In this work, a small amount of trimethylolpropane triacrylate (TMPTA) was incorporated into poly(ethylene terephthalate) (PET)/random terpolymer elastomer (ST2000) blends by melt-blending. The existence of TMPTA would induce the crosslinking of PET and ST2000 molecular chains at high temperatures of blending, resulting in the improvement in the impact strength but the loss in the tensile strength. When the PET/ST2000 blends were irradiated by gamma-ray radiation, the integrated mechanical properties could be enhanced significantly at a high absorbed dose. The irradiated sample at a dose of 100 kGy even couldn't be broken under the impact test load, and at the same time, has nearly no loss of tensile strength. Based on the analysis of the impactfractured surface morphologies of the blends, it can be concluded that gamma-ray radiation at high absorbed dose can further in situ enhance the interfacial adhesion by promoting the crosslinking reactions of TMPTA and polymer chains. As a result, the toughness and strength of PET/ST2000 blend could be dramatically improved. This work provides a facial and practical way to the fabrication of polymer blends with high toughness and strength.     

Postgel properties in the statistical crosslinking of heterochains. II. Free‐radical crosslinking copolymerization

The heterochain crosslinking theory is applied to postgel behavior in the free‐radical crosslinking copolymerization of vinyl and divinyl monomers. In this context, the crosslinked polymer formation can be viewed as a system in which the primary chains formed at different times are combined in accordance with the statistical chain‐connection rule governed by the chemical reaction kinetics. Because the primary chains are formed consecutively, the number of chain types N must be extrapolated to infinity, N → ∞. Practically, such extrapolation can be conducted with the calculated values for only three different N values. The analytical expressions for the weight fraction and average molecular weights of the sol fraction are derived for the general primary chain length distribution function in free‐radical polymerization. Illustrative calculations show that the obtained results agree with those from the Monte Carlo method, and that the postgel properties in free‐radical crosslinking copolymerization systems could be significantly different from those in randomly crosslinked systems. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2342–2350, 2000     

Interfacial slip at the thermotropic liquid‐crystalline polymer/poly (ethylene naphthalate) interface

The unique rheological properties of a thermotropic liquid‐crystalline polymer (TLCP) were first studied. The thermal and shear history of the TLCP was found to play a critical role in its rheological properties. Crystallites were observed in the TLCP melt even above the melting temperature detected by differential scanning calorimetry. Because interfacial slip had long been suggested as an important reason for viscosity reduction in TLCP/thermoplastic blends, for the first time, interfacial slip at the TLCP/poly(ethylene naphthalate) (PEN) interface was investigated with an energy model. The model quantified the degree of interfacial slip at the TLCP/PEN interface by an energy factor. The calculated energy factors revealed a high degree of interfacial slip at the TLCP/PEN interface. It was proposed that the high rigidity of rodlike TLCP chains and their alignment parallel to the interface prevented mutual entanglements at the TLCP/PEN interface. The lack of mutual entanglements promoted the interfacial slip. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 302–315, 2004     

Synthesis of networked polymer based on ring‐opening addition reaction of 1,3‐benzoxazine with resorcinol

A highly efficient ring‐opening addition reaction of benzoxazine at ambient temperature has been developed with 2‐methylresorcinol as a nucleophilic reagent. In this reaction, 2‐methylresorcinol reacted with two equivalent amount of benzoxazine to give the corresponding 1:2 adduct, demonstrating its potential as a bifunctional nucleophile. Based on this reaction, a new crosslinking system consisting of a polymer bearing benzoxazine moieties in the side chains and 2‐methylresorcinol as a crosslinker has been performed to obtain the corresponding networked polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Interfacial adhesion mechanisms in incompatible semicrystalline polymer systems

The mechanism of adhesion at semicrystalline polymer interfaces between isotactic polypropylene (iPP) and linear low‐density polyethylene (PE) was studied with transmission electron microscopy (TEM) and an asymmetric‐double‐cantilever‐beam test. From the TEM images, both the interfacial width and the lamellar thickness of the polymers were extracted. During annealing, the interfacial width increased with the annealing temperature, and this indicated the accumulation of amorphous polymers at the interface. The interfacial strength, determined from the critical fracture energy (G_c), also increased with the annealing temperature and reached a maximum above the melting temperatures of iPP and PE, whereas the smallest G_c value was obtained below the melting temperatures of the two materials. A mechanism of interfacial strengthening was proposed accounting for the competition between the interdiffusion of PE and crystallization of iPP. As the annealing temperature increased, the rates of PE diffusion and iPP crystallization increased. Although the crystallization of iPP hindered the interdiffusion of PE, both the interfacial width and the fracture energy increased with the temperature, and this indicated that PE interdiffusion dominated iPP crystallization. Below the critical temperature, the fracture surfaces of both iPP and PE were smooth, and chain pullout dominated the fracture mechanism. Above the critical temperature, iPP crystallization still hindered the interdiffusion, and crazes could be seen on the iPP side. Above the melting temperatures of the two materials, ruptured surfaces could also be seen on the PE side, and crazing was the fracture mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2667–2679, 2004     

Densely crosslinked polycarbosiloxanes. II: Thermal and mechanical properties

The thermal and mechanical properties of two densely crosslinked polycarbosiloxane systems were investigated in relation to the molecular structure. The networks were prepared from functional branched prepolymers and crosslinked via a hydrosilylation curing reaction. The prepolymers having only vinyl functionalities (poly[phenylmethylvinyl]siloxanes) were crosslinked by using crosslinking agents with reactive silicon–hydrogen groups. In prepolymers having both silicon–vinyl and silicon–hydrogen groups (poly[phenylmethylvinylhydro)]siloxanes crosslinking took place intermolecularly. The thermal and mechanical properties of the polymer networks were found to be dependent on the phenyl  Si O_3/2 (branches) content in the prepolymer, the number of elastically effective crosslinks, the elastically effective network chain density and molecular weight between crosslinks, length of the chain segments introduced by the hydrosilylation crosslinking reaction, and the number of dangling ends. As a consequence of the dense crosslinking, the mechanical properties were also strongly dependent on the glass transition temperature. A tough–brittle transition was observed around the glass transition temperature of the polymer networks. The properties of the poly(phenylmethylvinylhydro)siloxane networks were found to be superior to those of the poly(phenylmethylvinyl)siloxane networks. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1311–1331, 1997