Oxygen‐barrier properties of cold‐crystallized and melt‐crystallized poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

This study examined the oxygen‐transport properties of poly(ethylene terephthalate‐co‐bibenzoate) (PETBB55) crystallized from the melt (melt crystallization) or quenched to glass and subsequently isothermally crystallized by heating above the glass‐transition temperature (cold crystallization). The gauche–trans conformation of the glycol linkage was determined by infrared analysis, and the crystalline morphology was examined by atomic force microscopy. Oxygen solubility decreased linearly with volume fraction crystallinity. For melt‐crystallized PETBB55, extrapolation to zero solubility corresponded to an impermeable crystal with 100% trans glycol conformations, a density of 1.396 g cm^?3, and a heat of melting of 83 J g^?1. From the melt, PETBB55 crystallized as space‐filling spherulites with loosely organized lamellae and pronounced secondary crystallization. The morphological observations provided a structural model for permeability consisting of impermeable platelets randomly dispersed in a permeable matrix. In contrast, cold‐crystallized PETBB55 retained the granular texture of the quenched polymer despite the high level of crystallinity, as measured by the density and heat of melting. Oxygen solubility decreased linearly with volume fraction crystallinity, but zero solubility corresponded to an impermeable defective crystal with a trans fraction of 0.83 and a density of 1.381 g cm^?3. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2489–2503, 2002     

Spectroscopic characterization of the rotational conformations in the disordered phase of poly(ethylene terephthalate)

Recently developed data processing techniques have been applied to determine the complete spectra of the trans and gauche isomers of PET and to use these spectra to determine the conformational composition of PET samples isothermally crystallized from the glassy state between 75 and 240°C. A linear correlation was found between normalized absorbance of conformational bands and density measurements, with the trans bands showing a positive slope and the gauche bands a negative slope. Extrapolation of the results from trans bands to zero percent of trans yields the density of the pure gauche isomer, 1.326 ± 0.002 g/cm³. Similarly, from the gauche bands the density of 100% crystalline trans is found to be 1.510 ± 0.014 g/cm³. Meanwhile, the density of the amorphous trans is calculated to be 1.430 ± 0.003 g/cm³. From these values and the combined density and infrared measurements, the content of trans isomers in the amorphous phase is calculated. It is found that the content of amorphous trans is a function of both annealing temperature and time. It is observed that the amorphous trans content decreases as the crystalline trans content increases. At high crystallinity, the amorphous trans content approaches zero. These amorphous trans isomers are associated with the extended units making up the interlamellar links. The loss of these extended trans interlamellar links is reflected in the mechanical properties of PET.     

Effect of crystallization on oxygen‐barrier properties of copolyesters based on ethylene terephthalate

The effect of crystallization from the glassy state (cold crystallization) on the oxygen‐barrier properties of copolyesters based on ethylene terephthalate with up to 10 mol % isophthalate, phthalate, or naphthalate was examined. Generally, crystallization affected diffusivity D more than solubility S; thus, the reduction in permeability P reflected primarily a reduction in D. Systematic changes in crystallinity made it possible to test free‐volume concepts in which permeation of a small gas molecule through a semicrystalline polymer is viewed as proceeding through the amorphous regions with an increased pathway (tortuosity) imposed by plateletlike crystallites. Of the copolymers studied, those with the highest isophthalate or phthalate content (10 mol %) conformed to the simple two‐phase model with constant densities of an impermeable crystalline phase and a permeable amorphous phase. Within the two‐phase model, solubility S correlated linearly with the volume fraction of the amorphous phase, and diffusivity D depended on crystallinity in accordance with the Nielsen model for randomly dispersed platelets with an aspect ratio of 4. The reduction in permeability of the other examined copolyesters could not be described only by the filler effect of crystallites. Data on solubility demonstrated a decrease in amorphous‐phase density upon cold crystallization (de‐densification) like that previously reported for polyethylene terephthalate. Increasing the isophthalate or phthalate content reduced the de‐densification effect, and 10 mol % of these comonomers was sufficient to eliminate the effect altogether. In contrast, 10 mol % naphthalate did not prevent de‐densification. This was attributed to different effects of kinked and linear comonomers on chain packing in the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1911–1919, 2001     

Fourier-transform infrared study of coextrusion-drawn poly(ethylene terephthalate)

The effects of initial morphology and extrusion temperature on the orientational anisotropy and conformational changes on coextrusion drawing of poly(ethylene terephthalate) (PET) have been determined by Fourier-transform polarized infrared spectroscopy. The samples were drawn from both amorphous and semicrystalline (50%) PET at 50 and 90°C. A strong influence of coextrusion drawing temperature was observed for overall chain orientation evaluated from the dichroic ratio of the 795-cm^?1 band for the samples prepared from the amorphous state: this dependence was less prominent in samples drawn from the semicrystalline state. Under the same drawing conditions, the dichroic ratio for the 973-cm^?1 trans band for samples prepared from the amorphous state was higher than from the semicrystalline state. Furthermore, in all samples, the relative intensity of this band was almost proportional to the degree of crystallinity. In all samples, the gauche content, evaluated from the 896-cm^?1 band, decreased with increasing draw ratio. However, the dichroic ratio of this band was near unity regardless of draw ratio, initial morphology, or extrusion temperature. From these results it is considered that all gauche units in the amorphous phase are almost isotropic in the extrusion-drawn samples with overall orientation arising largely from the crystalline chains possessing totally the trans conformation (973 cm^?1) in its content. In order to evaluate the deformation mechanism of the coextrusion drawing method, the relationship between the bulk and film surface orientation is also reported.     

Conformational Analysis of 1,2‐Di‐O‐Octanoyl‐Ethylene‐Glycerol During Aggregation

Conformational analysis of 1,2‐di‐O‐octanoyl‐ethylene‐glycerol during aggregation by 600 MHz ¹H NMR is described. In monomeric states, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol exists in 75% anti‐conformer and 25% gauche‐conformer. The first critical micelle concentration of 1,2‐di‐O‐octanoyl‐ethylene‐glycerol is calculated to be 4.5 mM. In micellar states, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol exists in 25% anti‐conformer and 75%) gauche‐conformer. When the concentration is greater than 10 mM, 1,2‐di‐O‐octanoyl‐ethylene‐glycerol probably aggregates to become the larger micelle, micelle II. In the second micellar state, 1,2‐di‐O‐octanoylethylene‐glycerol only exists in gauche‐conformer.     

Structural and conformational changes during thermally‐induced crystallization of poly(trimethylene terephthalate) by infrared spectroscopy

Conformational changes occurring during thermally‐induced crystallization of poly(trimethylene terephthalate) (PTT) by annealing have been studied using density measurement, differential scanning calorimetry (DSC), and mid‐infrared spectroscopy (MIR). Infrared spectra of amorphous and semicrystalline PTT were obtained, and digital subtraction of the amorphous contribution from the semicrystalline PTT spectra provided characteristic MIR spectra of amorphous and crystalline PTT. The normalized absorbance of 1577, 1173, and 976 cm^?1 were plotted against the crystallinity showing that these bands can be used unambiguously to represent the trans conformation while the band at 1358 cm^?1 can be used to represent gauche conformation of methylene segment. The presence of a weak band at 1358 cm^?1 in the amorphous spectrum suggested that a small amount of gauche conformation is present in the amorphous phase. Infrared spectroscopy has been used for the first time as a means to estimate the trans and gauche conformations of methylene segments in PTT as a function of T_a. The amount of gauche conformation was plotted against the crystalline fraction and the extrapolation of this plot to zero crystalline fraction provided a value of 0.07, suggested that the pure amorphous phase consist of ～ 7% gauche conformation. It was found that the amorphous and crystalline gauche conformation increases at the expense of amorphous trans conformation during thermally induced crystallization of PTT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1497–1504, 2008     

Oxygen barrier properties of crystallized and talc‐filled poly(ethylene terephthalate)

The improvement in oxygen barrier properties of poly(ethylene terephthalate) (PET) by incorporation of an impermeable phase such as crystallinity or talc platelets was examined. Crystallinity was induced by crystallization from the glassy state (cold crystallization). Microlayering was used to create talc‐filled structures with controlled layer architecture. The reduction of permeability in crystallized and talc‐filled PET was well described by Nielsen's model. Changes in permeability of crystalline PET could not be ascribed to the filler effect of crystallites only. Our data on solubility, obtained on the basis of measurements of the oxygen transport coefficients, confirmed a previous finding that the amorphous phase density of PET decreases upon crystallization. The data were amenable to interpretation by free volume theory. Talc‐filled materials processed by different methods showed the same permeability; however, much better mechanical properties were achieved by microlayering. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 847–857, 1999     

2‐Propynyl 2,3,4,6‐tetra‐O‐acetyl‐α‐d‐mannopyranoside

The 2‐propynyl group in the title compound, C₁₇H₂₂O₁₀, adopts an exoanomeric conformation, with the acetylenic group gauche with respect to position C1. Comparison of ¹³C NMR chemical shifts from solution and the solid state suggest that the acetylenic group also adopts a conformation anti to C1 in solution. The pyranose ring adopts a ⁴C₁ conformation. Of the three secondary O‐acetyl groups, that on position O4, flanked by two equatorial groups, adopts a syn conformation, in agreement with recent generalizations [González‐Outeiriño, Nasser & Anderson (2005). J. Org. Chem. 70 , 2486–2493]. The acetyl group on position O3 adopts a gauche conformation, also in agreement with the recent generalizations, but that on position O2 adopts a syn conformation, not in agreement with the recent generalizations.     

Analysis of the nitrile and methyl torsional vibrations of n‐propyl cyanide in its S0 electronic state

This work presents a structural and vibrational theoretical study of n‐propyl cyanide as a function of the nitrile and methyl torsional modes. A potential energy hypersurface is built at the MP4(SDQ)/aug‐cc‐pVTZ//MP2/aug‐cc‐pVTZ theory level. The equilibrium structure is found in a gauche conformation. Another minimum is found for the trans form. The maximum appears in a cis conformation. For the first time, the interconversion barriers between the different forms are calculated. A two‐dimensional anharmonic vibrational Hamiltonian is built for the nitrile and methyl torsional modes. We find the vibrational energy levels to organize in two stacks associated to the gauche and trans forms. Fundamental frequencies of 113.12 and 220.54 cm^?1 are predicted for the nitrile and methyl torsions in the equilibrium, gauche, conformer. In addition, we find symmetry allowed transitions between the gauche and trans energy levels stacks. The lowest transition is predicted to appear at 24.49 cm^?1. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Infrared spectroscopic study of solvent-induced structural changes in poly(ethylene terephthalate) film

It is found from polarized infrared spectroscopy that treatment of oriented poly(ethylene terephthalate) (PET) film with strongly interacting solvents such as s-tetrachloroethane, nitrobenzene, dimethylformamide, and benzyl alcohol results in disorientation of polymer chains. Partial transformation from trans to gauche conformation takes place on thermal treatment and, to a larger extent, on solvent treatment. Increasing sharpness of the 988 cm^?1 band on solvent treatment indicates the formation of regular chain folds. Some new spectral features are discussed.     

{5′‐O‐[Bis(4‐methoxyphenyl)(phenyl)methyl]‐2′‐deoxy‐β‐D‐threopentofuranosyl}thymine ethyl acetate 0.25‐solvate

The title compound, C₃₁H₃₂N₂O₇·0.25C₄H₈O₂, is a key intermediate in the synthesis of [¹⁸F]fluorine‐labelled thymidine (¹⁸F‐FLT), which is the most widely used molecular imaging probe for positron emission tomography (PET). The crystallographic asymmetric unit contains two independent thymine molecules plus one partially occupied site for an ethyl acetate molecule. The two independent thymine molecules show similar geometrical features, except that the dimethoxytrityl groups adopt different orientations with respect to the remainder of the molecule. Each thymine base adopts an anti conformation with respect to the attached deoxyribose ring, and the deoxyribose rings show C3‐endo puckering. The conformation of the side chain at the C1 position of the deoxyribose ring is gauche+. Intermolecular N—H...O and O—H...O hydrogen bonds link the molecules into one‐dimensional chains.     

O‐Ethyl and O‐methyl N‐(2,3,4,6‐tetra‐O‐acetyl‐β‐d‐glucopyranosyl)thiocarbamate

In both the title structures, O‐ethyl N‐(2,3,4,6‐tetra‐O‐acetyl‐β‐d ‐gluco­pyran­osyl)­thio­carbam­ate, C₁₇H₂₅NO₁₀S, and O‐methyl N‐(2,3,4,6‐tetra‐O‐acetyl‐β‐d ‐gluco­pyran­osyl)­thiocar­bam­ate, C₁₆H₂₃NO₁₀S, the hexo­pyran­osyl ring adopts the ⁴C₁ conformation. All the ring substituents are in equatorial positions. The acetoxy­methyl group is in a gauche–gauche conformation. The S atom is in a synperi­planar conformation, while the C—N—C—O linkage is antiperiplanar. N—H?O intermolecular hydrogen bonds link the mol­ecules into infinite chains and these are connected by C—H?O interactions.     

Oxygen‐barrier properties of cold‐drawn polyesters

The improvement of oxygen‐barrier properties of glassy polyesters by orientation was examined. Poly(ethylene terephthalate) (PET), poly(ethylene naphthalate), and a copolymer based on PET in which 55 mol % of the terephthalate was replaced with bibenzoate (PET‐BB55) were oriented by constrained uniaxial stretching. In a fairly narrow window of stretching conditions near the glass‐transition temperature, it was possible to achieve uniform extension of the polyesters without crystallization or stress whitening. The processes of orientation and densification correlated with the conformational transformation of glycol linkages from gauche to trans. Oxygen permeability, diffusivity, and solubility decreased with the amount of orientation. A linear relationship between the oxygen solubility and polymer specific volume suggested that the cold‐drawn polyester could be regarded as a one‐phase densified glass. This allowed an analysis of oxygen solubility in accordance with free‐volume concepts of gas permeability in glassy polymers. Orientation was seen as the process of decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium (zero‐solubility) condition. Cold drawing most effectively reduced the free volume of PET‐BB55. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 862–877, 2002     

Synthesis of bio‐based poly(ethylene 2,5‐furandicarboxylate) copolyesters: Higher glass transition temperature,better transparency,and good barrier properties

The bio‐based polyester, poly(ethylene 2,5‐furandicarboxylate) (PEF), was modified by 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol (CBDO) via copolymerization and a series of copolyesters poly(ethylene‐co‐2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol 2,5‐furandicarboxylate)s (PETFs) were prepared. After their chemical structures and sequence distribution were confirmed by nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), their thermal, mechanical, and gas barrier properties were investigated in detail. Results showed that when the content of CBDO unit in the copolyesters was increased up to 10 mol%, the completely amorphous copolyesters with good transparency could be obtained. In addition, with the increasing content of CBDO units in the copolyesters, the glass transition temperature was increased from 88.9 °C for PET to 94.3 °C for PETF‐23 and the tensile modulus was increased from 3000 MPa for PEF to 3500 MPa for PETF‐23. The barrier properties study demonstrated that although the introduction of CBDO units would increase the O₂ and CO₂ permeability of PEF slightly, PECF‐10 still showed better or similar barrier properties compared with those of PEN and PEI. In one word, the modified PEF copolyesters exhibited better mechanical properties, higher glass transition temperature, good barrier properties, and better clarity. They have great potential to be the bio‐based alternative to the popular petroleum‐based poly(ethylene terephthalate) (PET) when used as the beverage packaging materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3298–3307     

8‐Aza‐7‐deaza‐7‐propynyladenosine methanol solvate

In the title compound, 4‐amino‐3‐propynyl‐1‐(β‐d ‐ribofur­anosyl)‐1H‐pyrazolo[3,4‐d]pyrimidine methanol solvate, C₁₃H₁₅N₅O₄·CH₃OH, the torsion angle of the N‐glycosylic bond is between anti and high‐anti [χ = −101.8 (5)°]. The ribofuranose moiety adopts the C3′‐endo (³T₂) sugar conformation (N‐type) and the conformation at the exocyclic C—C bond is +sc (gauche, gauche). The propynyl group is out of the plane of the nucleobase and is bent. The compound forms a three‐dimensional network which is stabilized by several hydrogen bonds (O—H·O and O—H·N). The nucleobases are stacked head‐to‐tail. The methanol solvent mol­ecule forms hydrogen bonds with both the nucleobase and the sugar moiety.     

p‐Cresyl 2,3‐an­hydro‐5‐deoxy‐5‐phthal­imido‐1‐thio‐α‐d‐lyxo­furan­oside

The crystal structure of the title compound, C₂₀H₁₇NO₄S, (I), was determined in order to compare the solution and solid‐state conformations. The mol­ecule was synthesized as a building block for incorporation into oligosaccharides comprised of conformationally restricted furan­ose residues. The furan­ose ring adopts an envelope conformation with the ring O atom displaced above the plane (an ^OE conformation). The pseudorotational phase angle (P) is 88.6° and the puckering amplitude (τ_m) is 31.5°. The C₂—C₁—S—C(Ph) torsion angle is ?163.2 (2)°, which places the aglycone in the exo‐anomeric effect preferred position. The C1—S—C14 bond angle is 99.02 (13)° and the plane of the cresyl moiety is oriented nearly parallel to the four in‐plane atoms of the furan­ose ring envelope. The orientation about the C4—C5 bond is gauche–gauche [Bock & Duus (1994). J. Carbohydr. Chem. 13 , 513–543].     

FTIR spectroscopic characterization of structural changes in polyamide‐6 fibers during annealing and drawing

First, we report the development of Fourier transform infrared (FTIR) spectroscopic methods to determine the α/γ‐crystalline phase ratio of polyamide‐6 fibers and, in combination with density measurements, the total crystallinity. Using density determinations of the crystallinity of pure α and pure γ samples, we found the absorption coefficient ratio for the 930 (α) and 973 cm⁻¹ (γ) bands to be 4.4, from which we could obtain the α/γ ratio for any polyamide‐6 sample. The application of this FTIR method to the quantitative analysis of phase changes during thermal treatment and the drawing of polyamide‐6 was then made. We confirmed that crystallization during thermal treatments involved increases in both phases and did not involve crystal‐to‐crystal transformation, whereas drawing involved both crystallization of the amorphous phase in the α form and γ→α transformation. Finally, we revisited the band assignments for the amorphous phase of polyamide‐6 and found that the band at 1170 cm⁻¹ was not an amorphous band but, because its absorbance was independent of crystallinity, could be used as an internal reference band. The band at 1124 cm⁻¹ was reliably attributed to the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 536–547, 2001     

Properties and morphology of recycled poly(ethylene terephthalate)/bisphenol a polycarbonate/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) blends by low‐temperature solid‐state extrusion

Among the various methods available for recycling plastics waste, blending technology is a straightforward and relatively simple method for recycling. In this paper, a new blending technology, low‐temperature solid‐state extrusion, was discussed. Several recycled poly(terephthalate ethylene)/bisphenol a polycarbonate/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) blends (R‐PET/PC/SEBS blends) have been prepared by this technology. The results show that thermal and hydrolytic degradation of R‐PET is improved when extruding temperature was between the glass transition temperature (T_g) and cold crystallization temperature (T_cc). Elongation at break and notched impact strength were increased evidently, from 15.9% to 103.6, and from 8.6 kJ/m² to 20.4 kJ/m², respectively. The appropriate rotating speed of screws was between 100 and 150 rpm. At the same time, the appropriate rotating speed of the screws brings a suitable shear viscosity ratio of R‐PET and PC, which is of advantage to blending of R‐PET and PC together with SEBS. Dispersion of minor phase, PC and SEBS, became finer and smaller, to about 1 µm. Chain extender, Methylenediphenyl diisocyanate (MDI) can react with the end‐carboxyl group and end‐hydroxyl group of R‐PET. FT‐IR spectra testified that the reactions have been happened in the extruding process. A chain extending reaction not only increased the molecular weight of PET and PC, but also can synthesize PET‐g‐PC copolymer to act as a reactive compatilizer. An SEM micrograph shows that a micro‐fiber structure of PET was formed in the blend sample. Copyright © 2007 John Wiley & Sons, Ltd.     

Aggregation behavior of polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer in N‐methylpyrrolidone

Solution property of hydrogenated polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer (SEBS copolymer) was studied by using static light scattering and dynamic light scattering for cyclohexane and N‐methylpyrrolidone (NMP) solutions. From the values of dimensionless parameters ρ, defined as the ratio of radius of gyration 〈S²〉^1/2 to hydrodynamic radius R_H, and solubility parameters, SEBS copolymer proved to exist as single chain close to random coil in nonpolar cyclohexane, whereas aggregate into the core‐shell micelle consisting of poly(ethylene/butylene) (PEB) core surrounded by PS shell in polar NMP. The core‐shell micelle formed in NMP is composed of 65 polymer chains, having three times larger average chain density (d = 0.12 g cm^?3) than a single polymer chain (d = 0.04 g cm^?3) in cyclohexane. The comparison with the aggregation behaviors in other solvents demonstrated that the aggregate compactness of the copolymer depended largely on solvent polarity, resulting in formation of the highly dense PEB core (R_c = 4.5 nm) and the thick PS shell (ΔR = 22.9 nm) in high‐polar NMP. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 588–594, 2010     

Raman Spectroscopic Study on Alkyl Chain Conformation in 1‐Butyl‐3‐methylimidazolium Ionic Liquids and their Aqueous Mixtures

Ionic liquids of 1‐butyl‐3‐methylimidazolium ([BMIM]) cation with different anions (Cl^?, Br^?, I^?, and BF₄^?), and their aqueous mixtures were investigated by using Raman spectroscopy and dispersion‐included density functional theory (DFT). The characteristic Raman bands at 600 and 624 cm^?1 for two isomers of the butyl chain in the imidazolium cation showed significant changes in intensity for different anions as well as in aqueous solutions. The area ratio of these two bands followed the order I^?>Br^?>Cl^?>BF₄^? (in terms of the anion X in [BMIM]X), indicating that the butyl chain of [BMIM]I tends to adopt the trans conformation. The butyl chain was found to adopt the gauche conformation upon dilution, irrespective of the anion type. The Raman bands in the butyl C?H stretch region for [BMIM]X (X=Cl^?, Br^?, and I^?) blueshifted significantly with the increase in the water concentration, whereas that for [BMIM]BF₄ changed very little upon dilution. The blueshift in the C?H stretch region upon dilution also followed the order: [BMIM]I>[BMIM]Br>[BMIM]Cl>[BMIM]BF₄, the same order as the above trans conformation preference of the butyl chain in pure imidazolium ionic liquids, which suggested that the cation‐anion interaction plays a role in determining the conformation of the chain.