Synthesis of an electroluminescent polymer and its non‐doped light‐emitting diodes with stable green emission

An electroluminescent polymer was synthesized by Wittig condensation and characterized by the measurements of ¹H‐NMR, IR, gel permeation chromatography (GPC), UV–Vis, PL, and cyclic voltammetry (CV). The polymer can be dissolved in common organic solvents such as tetrahydrofuran (THF), chloroform, and dichloromethane. The electroluminescent investigation showed that the non‐doped devices with a double‐layer configuration (ITO/PEDOT:PSS/Polymer/Mg:Ag) have a stable green emission property. The maximum luminance of the annealed device reaches 2317 cd/m². The emission maximum and the CIE 1931 coordinate values are respectively stabilized at 552 nm and near (x, y) = (0.43, 0.55) with different voltages. Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(methyl methacrylate) copolymers containing pendant carbazole and oxadiazole moieties for applications in single‐layer organic light emitting devices

Methyl methacrylate derived monomers functionalized with pendant carbazole and oxadiazole moieties were synthesized and could be copolymerized to form a random copolymer. The glass transition temperature of the copolymers could be predicted with a Fox equation and ranged from 140 to 191 °C. The photoluminescent characteristics of the copolymers, both in solution and in solid films, exhibited emission that was a combination of sharp and broad peaks, suggestive of monomeric and chromophore aggregation emission. These trends were also apparent in the electroluminescent response of the copolymers, where the appearance of an electromer emission was evident and was tentatively assigned to the carbazole moieties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7882–7897, 2008     

New polyphenylene‐ and polyphenylenevinylene‐based copolymers containing triarylpyrazoline units in the main chains

Two novel polyphenylene and polyphenylenevinylene copolymers containing triarylpyrazoline units in the main chains were synthesized and characterized. The resulting copolymers were amorphous and showed excellent solubility in common organic solvents, such as dichloromethane, chloroform, 1,2‐dichloroethane, chlorobenzene, toluene, and THF. The polymers possessed good thermal stability with glass transition temperatures of 82 and 96 °C and decomposition onset temperatures of 295 and 309 °C, respectively. They exhibited good photoluminescence properties with high photoluminescence efficiencies. Double‐layered light‐emitting‐diode devices with an indium tin oxide/Poly(3,4‐ethylenedioxythiophene)/polymer/Ba/Al configuration could emit strong green light with external quantum efficiencies of0.53 and 0.92%. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1632–1640, 2007     

Synthesis of new polyfluorene copolymers with a comonomer containing triphenylamine units and their applications in white‐light‐emitting diodes

Novel conjugated polyfluorene copolymers, poly[9,9‐dihexylfluorene‐2,7‐diyl‐co‐(2,5‐bis(4′‐diphenylaminostyryl)‐phenylene‐1,4‐diyl)]s (PGs), have been synthesized by nickel(0)‐mediated polymerization from 2,7‐dibromo‐9,9‐dihexylfluorene and 1,4′‐dibromo‐2,5‐bis(4‐diphenylaminostyryl)benzene with various molar ratios of the monomers. Because of the incorporation of triphenylamine (TPA) moieties, PGs exhibit much higher HOMO levels than the corresponding polyfluorene homopolymers and are able to facilitate hole injection into the polymer layer from the anode electrode in light‐emitting diodes. Conventional polymeric light‐emitting devices with the configuration ITO/PEDOT:PSS/polymer/Ca/Al have been fabricated. A light‐emitting device produced with one of the PG copolymers (PG10) as the emitting layer exhibited a voltage‐independent and stable bluish‐green emission with color coordinates of (0.22, 0.42) at 5 V. The maximum brightness and current efficiency of the PG10 device were 3370 cd/m² (at 9.6 V) and 0.6 cd/A, respectively. To realize a white polymeric light‐emitting diode, PG10 as the host material was blended with 1.0 wt % of a red‐light‐emitting polymer, poly[9,9‐dioctylfluorene‐2,7‐diyl‐alt‐2,5‐bis(2‐thienyl‐2‐cyanovinyl)‐1‐(2′‐ethylhexyloxy)‐4‐methoxybenzene‐5′,5′‐diyl] (PFR4‐S), and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV). The device based on PG10:PFR4‐S showed an almost perfect pure white electroluminescence emission, with Commission Internationale de l'Eclairage (CIE) coordinates of (0.33, 0.36) at 8 V; for the PG10:MEH‐PPV device, the CIE coordinates at this voltage were (0.30, 0.40) with a maximum brightness of 1930 cd/m². Moreover, the white‐light emission from the PG10:PFR4‐S device was stable even at different driving voltages and had CIE coordinates of (0.34, 0.36) at 6 V and (0.31, 0.35) at 10 V. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1199–1209, 2007     

Luminescence of monolayer thin films of the fully conjugated rigid‐rod polymer poly(p‐phenylenebenzobisthiazole)

Poly(p‐phenylenebenzobisthiazole) (PBT) is a heterocyclic, aromatic rigid‐rod polymer with a fully conjugated backbone and excellent dimensional, thermo‐oxidative, and solvent stabilities. A PBT polymer with an intrinsic viscosity of 18.0 dL/g was dissolved in methanesulfonic acid or Lewis acid. The PBT solution was spin‐coated and doctor‐bladed for freestanding films or onto an indium tin oxide (ITO) substrate. The acid was removed via coagulation. Scanning electron microscopy determined that the resultant film thicknesses were about 340 and 60 nm for PBT freestanding films and films on the ITO substrate, respectively. X‐ray scattering demonstrated that the freestanding films were in‐plane isotropic without long‐range order. The freestanding films were excited with a He‐Cd laser at 325 nm for photoluminescence (PL) response. PL spectra showed a distinct intensity maximum at 580 nm, regardless of the film‐forming conditions. After the films cooled to 67 K, the PL maximum shifted to 566 nm with enhanced intensity. Aluminum was evaporated onto the monolayer PBT thin film on the ITO substrate as an electron injector for electroluminescence (EL) response. Diodic electric behavior was observed for all monolayer PBT EL devices for the first time. A threshold voltage as low as 4 V was achieved for the monolayer EL devices. In addition, PBT EL spectra were tunable, with a maximum intensity at 570 nm at a bias voltage of 4.5 V changing to 496 nm at 7.5 V (i.e., a blueshift) with greatly increased intensity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1760–1767, 2002     

Synthesis of phenothiazine‐based electroluminescent polymers with a stable emission property

Two phenothiazine‐based polymers were synthesized by the Heck reaction of 3,7‐divinyl‐N‐octyl‐phenothiazine with 3,7‐diiodo‐N‐octyl‐phenothiazine and 5,8‐dibromo‐2,3‐diethylquinoxaline. The polymers were characterized by the measurements of ¹H‐NMR, IR, TG, GPC, CV, UV–Vis, and FL. The results indicated that the introduction of quinoxaline group makes the absorption, PL, and EL emission maxima red‐shifted. The EL emission maximum and the CIE 1931 coordinate value are stabilized at a constant value with the increase in operating voltages. Therefore, the polymers have a stable electroluminescent emission property. Copyright © 2008 John Wiley & Sons, Ltd.     

Color tunability in non‐doped single‐layer PLEDs from a carbazole‐based electroluminescent polymer

A conjugated polymer with a carbazole moiety, poly(3,6‐divinylene‐N‐octyl‐carbazole‐p‐phenylene), was synthesized by Wittig reaction. The polymer can be dissolved in common organic solvents such as THF, chloroform, etc. Using this polymer as an active layer, single‐layer non‐doped PLEDs with different thicknesses were fabricated by a spin‐coating approach. The results suggested that electroluminescence spectra are changed with the film thickness of the polymer emitter. Fortunately, CIE 1931 coordinate values are moved to the white‐light region only by changing the film thickness. Copyright © 2008 John Wiley & Sons, Ltd.     

Alkyl side chain driven tunable red–yellow–green emission: Investigation on the new π‐conjugated polymers comprising of 2,7‐carbazole unit and 2,1,3‐benzo‐thiadiazole units with different side chains

Four new soluble polymers containing a 2,7‐carbazole unit and a 2,1,3‐benzothiadiazole unit in the main chain were synthesized by Suzuki polycondensation. Variation of the substituent groups (R) at 5‐position of 2,1,3‐benzothiadiazole unit resulted in different color emission of the copolymers. Thus, when R was ? CH₃ (or ? H), the polymer showed yellow–green (or red) emission; whereas the polymers showed the emission from green to yellow–green, when R was ? CH₂(CH₂)₅CH₃ or ? CH₂OCH(CH₃)₂. To investigate the nature of the color change, a Gaussian 03 program was used for estimation of the dihedral angles between a 5‐R‐2,1,3‐benzothiadiazole unit and a 2,7‐carbazole unit. The results showed that the different substituents at 5‐position of 2,1,3‐benzothiadiazole brought about different the dihedral angles, which gave the different conjugation levels to the polymers. Hence, the tunablity of emission color may be attributed to the different conjugation levels between 2,7‐carbazole units and 5‐R‐2,1,3‐benzothiadiazole units induced by simply changing substituent groups at 5‐position of benzothiadiazole unit. Electrochemically, the copolymers exhibited a higher oxidation potential as well as the reversible reduction behavior bearing from 2,1,3‐benzothiadiazole unit. To investigate the electroluminescent properties of the polymers, the nonoptimized devices were fabricated and the results showed that the electroluminescent emission wavelength was basically similar to that of the photoluminescent. All polymers showed good thermal stability with 5 wt % loss temperature of more than 296 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1376–1387, 2008     

Hole‐transporting host‐polymer series consisting of triphenylamine basic structures for phosphorescent polymer light‐emitting diodes

A series of novel styrene derived monomers with triphenylamine‐based units, and their polymers have been synthesized and compared with the well‐known structure of polymer of N,N′‐bis(3‐methylphenyl)‐N,N′‐diphenylbenzidine with respect to their hole‐transporting behavior in phosphorescent polymer light‐emitting diodes (PLEDs). A vinyltriphenylamine structure was selected as a basic unit, functionalized at the para positions with the following side groups: diphenylamine, 3‐methylphenyl‐aniline, 1‐ and 2‐naphthylamine, carbazole, and phenothiazine. The polymers are used in PLEDs as host polymers for blend systems with the following device configuration: glass/indium–tin–oxide/PEDOT:PSS/polymer‐blend/CsF/Ca/Ag. In addition to the hole‐transporting host polymer, the polymer blend includes a phosphorescent dopant [Ir(Me‐ppy)₃] and an electron‐transporting molecule (2‐(4‐biphenyl)‐5‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazole). We demonstrate that two polymers are excellent hole‐transporting matrix materials for these blend systems because of their good overall electroluminescent performances and their comparatively high glass transition temperatures. For the carbazole‐substituted polymer (T_g = 246 °C), a luminous efficiency of 35 cd A^?1 and a brightness of 6700 cd m^?2 at 10 V is accessible. The phenothiazine‐functionalized polymer (T_g = 220 °C) shows nearly the same outstanding PLED behavior. Hence, both these polymers outperform the well‐known polymer of N,N′‐bis(3‐methylphenyl)‐N,N′‐diphenylbenzidine, showing only a luminous efficiency of 7.9 cd A^?1 and a brightness of 2500 cd m^?2 (10 V). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3417–3430, 2010     

Donor–acceptor copolymers for red‐ and near‐infrared‐emitting polymer light‐emitting diodes

We report a comparative study of two organic soluble, vinylene‐based, alternating donor–acceptor copolymers with 1,4‐(2,5‐dihexadecyloxyphenylene) as the donor; the acceptor is either a 2,5‐linked pyridine or a 5,8‐linked 2,3‐diphenylpyrido[3,4‐b]pyrazine. The polymers are synthesized via a Heck coupling methodology from a dihalo monomer and a divinyl monomer to yield number‐average molecular weights of 16,000 g/mol for the pyridine polymer (PPyrPV) and 6500 g/mol for the pyridopyrazine polymer (PPyrPyrPV), with high solubility in common chlorinated solvents and lower solubility in less polar solvents (e.g., tetrahydrofuran). Thin‐film measurements show band gaps of 2.2 and 1.8 eV for PPyrPV and PPyrPyrPV, respectively. Both polymers exhibit photoluminescence in solution and in the solid state and exhibit electroluminescence when incorporated into light‐emitting diodes. In this case, a broad red emission centered at 690 nm for PPyrPV and a near‐infrared emission centered at 800 nm for PPyrPyrPV have been observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1417–1431, 2005     

Novel saturated red‐emitting poly(p‐phenylenevinylene) copolymers with narrow‐band‐gap units of 2,1,3‐benzothiadiazole synthesized by a palladium‐catalyzed Stille coupling reaction

Novel poly(p‐phenylenevinylene) (PPV) copolymers derived from 1‐methoxy‐4‐octyloxyphenylene (MOP), 2,1,3‐benzothiadiazole (BT), and trans‐1,2‐bis(tributylstannyl)ethylene were first prepared by a palladium‐catalyzed Stille coupling reaction. The feed ratios of MOP to BT were 99.5:0.5, 99:1, 95:5, 85:15, 70:30, and 50:50. An efficient energy transfer from the 2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene segment to the narrow‐band‐gap units was observed. The poly(2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene‐2,1,3‐benzothiadiazolevinylene) copolymers emitted deep red light. The maximum electroluminescence emission of these PPV copolymers occurred at 659–724 nm and was accompanied by gradual redshifting with an increasing BT concentration. The photophysical properties were examined in comparison with those of copolymers based on BT and fluorene or N‐alkylcarbazole doped with the same BT concentration in the copolymer main chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2325‐2336, 2005     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

Rational design of methacrylate monomers containing oxadiazole moieties for single‐layer organic light emitting devices

Methacrylate derived monomers functionalized with pendant oxadiazole moieties were synthesized and copolymerized with carbazole containing monomers to form polymers with electron and hole transporting fragments in the same molecule. Substituents on the oxidazole moiety were varied with the purpose of bandgap tuning and performance optimization when employed in single‐layer organic light emitting devices (OLED). Quantum mechanical calculations of the HOMO‐LUMO levels of the oxidazole derivatives were used to down‐select promising candidates for chemical synthesis and testing in single‐layer OLEDs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1663–1673     

Electroluminescent properties of anthracene‐containing polyimides

Optical and electroluminescent properties of a new soluble anthracene‐containing polyimide (ACPI) was studied. Solubility of ACPI in organic solvents allows direct spin casting of the polymer films exhibiting intense photo‐ and electroluminescence (EL) in the visible range. This non‐conjugated polymer was used as emitting and electron‐hole transporting layers in polymer light‐emitting devices (LEDs). EL properties of the uni‐ and bilayer LEDs are discussed in terms of the band structure, bipolar transport and electron donor‐acceptor interactions. Copyright © 2000 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel red‐emitting alternating copolymers based on fluorene and diketopyrrolopyrrole derivatives

Two novel alternating copolymers, poly{9,9‐dihexylfluorene‐2,7‐diyl‐alt‐2,5‐dioctyl‐3,6‐bis(4‐phenyl)pyrrolo[3,4‐c] pyrrole‐1,4‐dione} ( P1 ) and poly{9,9‐dihexylfluorene‐2,7‐diyl‐alt‐2,5‐dioctyl‐3,6‐bis(3‐phenyl)pyrrolo[3,4‐c] pyrrole‐1,4‐dione} ( P2 ), derived from 9,9‐dihexylfluorene and diketopyrrolopyrrole (DPP), have been successfully synthesized through palladium‐catalyzed Suzuki polycondensation in good yields. P1 and P2 possess moderate molecular weights and polydispersities, well‐defined structures, and excellent thermal properties with an onset decomposition temperature around 400 °C. Both P1 and P2 in thin films exhibit red photoluminescence from DPP species exclusively, with peaks at 609 and 616 nm, respectively. Cyclic voltammetry studies show that P1 and P2 have low‐lying lowest unoccupied molecular orbital energy levels at ?3.65 eV and reversible reduction processes, so these polymers may constitute another kind of red‐emitting polymer with high electron affinity. Preliminary electroluminescent results of devices with an indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer/Ba/Al configuration reveal that P1 may be a promising candidate for red emitters with a maximum brightness of 153 cd/m² and a maximum external quantum efficiency of 0.13%, whereas the performance of P2 is relatively poor. These differences might originate from different conjugation lengths in their main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2395–2405, 2006     

Synthesis of novel nitrogen‐ and sulfur‐containing conjugated polymers used as hole‐transporting materials for organic light‐emitting diodes

Two series of highly soluble novel nitrogen‐ and sulfur‐containing conjugated polymers were synthesized via an acid‐induced self‐polycondensation of functional monomers with methyl sulfinyl and aromatic groups. The well‐defined structures of synthesized polymers were confirmed by their NMR and IR spectra. The highest occupied molecular orbital energy values for these materials, estimated by cyclic voltammetry, showed a broad range of values from about 5.0 to 5.2 eV used as hole‐transport layers (HTL) in two‐layer light‐emitting diodes ITO/HTL/Alq₃/Mg:Ag [ITO = indium tin oxide, and Alq₃ = tris(8‐quinolinato) aluminum]. The typical turn‐on voltage of these diodes was about 4–5 V. The maximum brightness of the device was about 3440 cd/m² at 20 V. The maximum efficiency was estimated to be 0.15 lm/W at 10 V. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1321–1333, 2002     

Synthesis and characterization of new light‐emitting copolymers in polymeric‐light‐emitting‐diode device fabrications

A series of thiophene‐containing photoactive copolymers consisting of alternating conjugated and nonconjugated segments were synthesized. The ¹H NMR spectra corroborated the well‐defined structures, and the copolymers not only were soluble in common organic solvents but also had high glass‐transition temperatures (ca. 130 °C) and good thermal stability up to 390 °C. Introducing aliphatic functional groups, such as alkyl or alkoxyl, into chromophores of the copolymers redshifted the photoluminescence spectra and lowered the optical bandgaps. The electrochemical bandgaps calculated from cyclic voltammetry agreed with the optical bandgaps and thus indicated that electroluminescence and photoluminescence originated from the same excited state. The energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) of all the copolymers were lower than those of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1.4‐phenylenevinylene] MEH–PPV, indicating balanced hole and electron injection, which led to improved performance in both single‐layer and double‐layer polymeric‐light‐emitting‐diode devices fabricated with these copolymers. All the copolymers emitted bluish‐green or green light above the threshold bias of 5.0 V under ambient conditions. At the maximum bias of 10 V, the electroluminescence of a device made of poly(2‐{4‐[2‐(3‐ethoxy phenyl)ethylene]phenyl}‐5‐{4‐[2‐(3‐ethoxy,4‐1,8‐octanedioxy phenyl)ethylene]phenyl}thiophene) was 5836 cd/m². The external electroluminescence efficiency decreased with the lifetime as the polymer degraded. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3954–3966, 2004     

Synthesis and characterization of novel luminescent polymers with alternate phenothiazine and divinylbenzene units

Novel luminescent polymers ( P1 and P2 ) carrying alternate phenothiazine and divinylbenzene units were synthesized via the Wittig reaction. Absorption, fluorescence, and cyclic voltammetric methods were applied to investigate their optical and electrochemical properties. The photoluminescence (PL) maxima of P1 and P2 were 559 and 568 nm, respectively. Compared with reported hole‐transport groups such as carbazole, alkyldiphenylamine, triphenylamine, and iminodibenzyl chromophores, phenothiazine moieties in P1 and P2 bathochromically shift the PL maxima and narrow the band gaps. Their relative PL efficiencies were about 0.5 and 0.3 in solution and in the film state, respectively. Moreover, highest occupied molecular orbitals of P1 (4.78 eV) and P2 (4.74 eV) were even higher than the work function of ITO electrode (4.8 eV). The threshold electric fields of the Al/ P1 (or P2 )/ITO device were about 1.52–1.63 · 10⁶ V/cm, which were smaller than 1.73 · 10⁶ V/cm of P3 , consisting of alternate iminodibenzyl and divinylbenzene units. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4452–4462, 2002     

Synthesis and characterization of luminescent copolymers containing iminodibenzyl and divinylbenzene chromophores

New conjugated copolymers containing alternating N‐hexyl‐3,8‐iminodibenzyl and divinylbenzene chromophores {poly(N‐hexyl‐3,8‐iminodibenzyl‐1,2‐ethenylene‐2,5‐dihexyloxy‐1,4‐phenylene‐1,2‐ethenylene) ( P1 ) and poly[N‐hexyl‐3,8‐iminodibenzyl‐2,5‐bis(hexyloxy)cyanoterephthalidene] ( P2 )} were synthesized according to Wittig and Knoevenagel polymerization. A copolymer containing alternating carbazole and divinylbenzene derivatives {poly[9‐(2‐ethylhexyl)‐3,6‐carbazole‐1,2‐ethenylene‐2,5‐dihexyloxy‐1,4‐phenylene‐1,2‐ethenylene] ( P3 )} was also synthesized for comparison. The copolymers were soluble in common organic solvents such as tetrahydrofuran and toluene. Absorption and photoluminescence measurements revealed that cyano substitution at the vinylene moiety in P2 brought about a significant bathochromic shift and led to an electroluminescence color change from green to orange. The band edge energies of the copolymers were estimated from cyclic voltammograms and optical band gaps. P1 and P3 showed similar highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, indicating that the electron‐donating abilities of the iminodibenzyl and carbazole chromophores were comparable. However, compared with those of P1 and P3 , the HOMO and LUMO levels of P2 were greatly reduced because of conjugating and electron‐withdrawing CN groups. The threshold electric field of an Al/ P1 /ITO glass single‐layer light‐emitting diode was approximately 10 × 10⁵ V/cm, whereas those for P2 and P3 were 7.5 and 16 × 10⁵ V/cm, respectively. The electroluminescence emission maxima of P1–P3 were 498, 514, and 559 nm, respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3847–3857, 2002     

Near‐infrared electroluminescence from fluorene‐based copolymers

A series of random low band‐gap conjugated copolymers (PFO‐DDTQ) derived from 9,9‐dioctylfluorene (DOF) and 6,7‐dimethyl‐4,9‐di(4‐hexylthien‐2‐yl)‐[1,2,5]thiadiazolo[3,4‐g]quinoxalines (DDTQ) are prepared by the palladium‐catalyzed Suzuki coupling reaction. The obtained polymers are readily soluble in common organic solvents. The thin solid films of the polymers absorb light from 300 to 840 nm with two absorbance peaks at around 380 and 710 nm. Electroluminescent peaks are between 0.8 and 0.9 μm based on the polymers. The maximal external quantum efficiency reaches 0.30% with the emission peak at 824 nm from PFO‐DDTQ1 based devices. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3007–3013, 2008