Flexibilized styrene‐N‐substituted maleimide copolymers. I. Multiblock copolymers prepared from styrene‐maleimide telechelics and polytetrahydrofuran

Telechelic copolymers of styrene and different N‐substituted‐maleimides (SMIs) with a molecular weight of 2000–8000 g/mol were synthesized using the starved‐feed‐reactor technique and were nearly bifunctional when the monomer feed had a high styrene concentration. The COOH‐terminated rigid SMI blocks were polycondensated with OH‐terminated poly(tetrahydrofuran) (PTHF) blocks, with a molecular weight of 250–1000 g/mol, which are the flexible parts in the generated homogeneous multiblock copolymer. The entanglement density, which is closely related to the toughness of materials, increased in these flexible SMI copolymers (ν_e = 5.2 · 10²⁵ m⁻³) compared to the unflexibilized ones (ν_e = 2.4 · 10²⁵ m⁻³). The glass transition temperature of these flexibilized, single‐phase multiblock copolymers was still high enough to qualify them as engineering plastics. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3550–3557, 2000     

Novel poly(l‐lactide)/poly(d‐lactide)/poly(tetrahydrofuran) multiblock copolymers with a controlled architecture: Synthesis and characterization

Novel poly(l ‐lactide) (PLLA)/poly(d ‐lactide) (PDLA)/poly(tetrahydrofuran) (PTHF) multiblock copolymers with designed molecular structure were synthesized by a two‐stage procedure. Well‐defined PDLA‐PLLA‐PTHF‐PLLA‐PDLA pentablock copolymers were prepared by sequential ring opening polymerization of l ‐ and d ‐lactides starting from PTHF glycol, with the length of the (equimolar) PLLA and PDLA blocks being varied. Then, these dihydroxyl‐terminated pentamers were transformed into multiblock copolymers by melt chain‐extension with hexamethylene diisocyanate–being the first time that the coupling of pentablock units is reported. The successful formation of macromolecular chains with a multiblock and well‐defined architecture was demonstrated by ¹H NMR spectroscopy. The thermal properties and structuring of the resulting materials were investigated by means of DSC and WAXD measurements and DMA analysis. Stereocomplexation was found to be promoted during solution and melt crystallization. This approach affords materials combining the high rigidity and strength (other than improved thermal resistance) of the hard stereocomplex crystallites with the flexibility imparted by the soft block, whereby their properties can be finely tailored through the composition of the basic pentablock units without limitations on the final molecular weight. The adopted reaction conditions make this process highly appealing in view of the possibility to perform it in extruder. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3269–3282     

Synthesis of amphiphilic multiblock and triblock copolymers of polydimethylsiloxane and poly(N,N‐dimethylacrylamide)

The synthesis and spectroscopic characterization of a new family of amphiphilic multiblock and triblock copolymers is described. The synthetic methodology rests on the preparation of telechelic multifunctional and difunctional chain transfer agents easily available in two synthetic steps from commercially available polydimethylsiloxane‐containing starting materials. Telechelic polymers thus synthesized are used as macromolecular chain transfer agents in the reversible addition fragmentation chain transfer (RAFT) polymerization of N,N‐dimethylacrylamide (DMA) enabling the synthesis of (AB)_n‐type multiblock and ABA‐type triblock copolymers of varying compositions possessing monomodal molecular weight distribution. (AB)_n multiblock copolymers [(PDMA‐b‐PDMS)_n] were prepared with between 52 and 95 wt % poly(dimethylacrylamide) with number average molecular weights (M_n) between 14,000 and 86,000 (polydispersities of 1.20–2.30). On the other hand, ABA block copolymers with DMA led to amphiphilic block copolymers (PDMA‐b‐PDMS‐b‐PDMA) with M_n values between 9000 and 44,000 (polydispersities of 1.24–1.62). © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7033–7048, 2008     

Hydrolytic degradation of polyisobutylene and poly‐L‐lactide–based multiblock copolymers

The hydrolytic degradation of a series of poly‐L ‐lactide (PLLA)‐polyisobutylene (PIB) multiblock copolymers was studied in phosphate buffer solution (pH = 7.4) at 37 °C. The multiblock copolymers were synthesized by chain extension of PLLA‐b‐PIB‐b‐PLLA triblock copolymers, which were obtained by ring‐opening polymerization of L ‐lactide initiated by hydroxyallyl telechelic PIB. The degradation strongly depended on the PLLA segment length. At constant PIB segment length, the multiblock copolymer with the shortest PLLA segment length (DPn = 10), showed significant weight loss after 8 weeks, whereas weight loss for DPn = 36 was only observed after 24 weeks. The gel‐permeation chromatographic analysis showed a similar decrease in the number‐average molecular weight (M_n) with time further supporting the weight loss data. Dynamic mechanical analysis showed a decrease in ultimate stress and modulus with time. The crystallinity of multiblock copolymers changed significantly with degradation time as indicated from differential scanning calorimetric analysis. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3767–3774, 2010     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Synthesis of comb‐shaped poly(methyl methacrylate)‐b‐poly(polytetrahydrofuran acrylate) under 60Co γ‐ray irradiation

Comb‐shaped graft copolymers with poly(methyl methacrylate) as a handle were synthesized by the macromonomer technique in two steps. First, polytetrahydrofuran acrylate (A‐PTHF), prepared by the living cationic ring‐opening polymerization of tetrahydrofuran, underwent homopolymerization with 1‐(ethoxycarbonyl)prop‐1‐yl dithiobenzoate as an initiator under ⁶⁰Co γ irradiation at room temperature; Second, the handle of the comb‐shaped copolymers was prepared by the block copolymerization of methyl methacrylate with P(A‐PTHF) as a macroinitiator under ⁶⁰Co γ irradiation. The two‐step polymerizations were proved to be controlled with the following evidence: the straight line of ln[M]₀/[M] versus the polymerization time, the linear increase in the number‐average molecular weight with the conversion, and the relatively narrow molecular weight distribution. The structures of the P(A‐PTHF) and final comb‐shaped copolymers were characterized by ¹H NMR spectroscopy and gel permeation chromatography. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3367–3378, 2002     

Segmented sulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers for proton exchange membrane fuel cells. I. Copolymer synthesis and fundamental properties

Segmented disulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers based on hydrophilic and hydrophobic oligomers were synthesized and evaluated for use as proton exchange membranes (PEMs). Amine terminated sulfonated poly (arylene ether sulfone) hydrophilic oligomers and anhydride terminated naphthalene based polyimide hydrophobic oligomers were synthesized via step growth polymerization including high temperature one‐pot imidization. Synthesis of the multiblock copolymers was achieved by an imidization coupling reaction of hydrophilic and hydrophobic oligomers oligomers in a m‐cresol/NMP mixed solvent system, producing high molecular weight tough and ductile membranes. Proton conductivities and water uptake increased with increasing ion exchange capacities (IECs) of the copolymers as expected. The morphologies of the multiblock copolymers were investigated by tapping mode atomic force microscopy (TM‐AFM) and their measurements revealed that the multiblock copolymers had well‐defined nano‐phase separated morphologies which were clearly a function of block lengths. Hydrolytic stability test at 80 °C water for 1000 h showed that multiblock copolymer membranes retained intrinsic viscosities of about 80% of the original values and maintained flexibility which was much improved over polyimide random copolymers. The synthesis and fundamental properties of the multiblock copolymers are reported here and the systematic fuel cell properties will be provided in a separate article. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4879–4890, 2007     

Synthesis and characterization of multiblock copolymers composed of poly(5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one) outer blocks and poly(L‐lactide) inner blocks

Ethylene glycol (EG) initiated, hydroxyl‐telechelic poly(L ‐lactide) (PLLA) was employed as a macroinitiator in the presence of a stannous octoate catalyst in the ring‐opening polymerization of 5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one (MBC) with the goal of creating A–B–A‐type block copolymers having polycarbonate outer blocks and a polyester center block. Because of transesterification reactions involving the PLLA block, multiblock copolymers of the A–(B–A)_n–B–A type were actually obtained, where A is poly(5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one), B is PLLA, and n is greater than 0. ¹H and ¹³C NMR spectroscopy of the product copolymers yielded evidence of the multiblock structure and provided the lactide sequence length. For a PLLA macroinitiator with a number‐average molecular weight of 2500 g/mol, the product block copolymer had an n value of 0.8 and an average lactide sequence length (consecutive C₆H₈O₄ units uninterrupted by either an EG or MBC unit) of 6.1. For a PLLA macroinitiator with a number‐average molecular weight of 14,400 g/mol, n was 18, and the average lactide sequence length was 5.0. Additional evidence of the block copolymer architecture was revealed through the retention of PLLA crystallinity as measured by differential scanning calorimetry and wide‐angle X‐ray diffraction. Multiblock copolymers with PLLA crystallinity could be achieved only with isolated PLLA macroinitiators; sequential addition of MBC to high‐conversion L ‐lactide polymerizations resulted in excessive randomization, presumably because of residual L ‐lactide monomer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6817–6835, 2006     

Quadruple click reactions for the synthesis of cysteine‐terminated linear multiblock copolymers

Synthesis of cysteine‐terminated linear polystyrene (PS)‐b‐poly(ε‐caprolactone) (PCL)‐b‐poly(methyl methacrylate) (PMMA)/or poly(tert‐butyl acrylate)(PtBA)‐b‐poly(ethylene glycol) (PEG) copolymers was carried out using sequential quadruple click reactions including thiol‐ene, copper‐catalyzed azide–alkyne cycloaddition (CuAAC), Diels–Alder, and nitroxide radical coupling (NRC) reactions. N‐acetyl‐L ‐cysteine methyl ester was first clicked with α‐allyl‐ω‐azide‐terminated PS via thiol‐ene reaction to create α‐cysteine‐ω‐azide‐terminated PS. Subsequent CuAAC reaction with PCL, followed by the introduction of the PMMA/or PtBA and PEG blocks via Diels–Alder and NRC, respectively, yielded final cysteine‐terminated multiblock copolymers. By ¹H NMR spectroscopy, the DP_ns of the blocks in the final multiblock copolymers were found to be close to those of the related polymer precursors, indicating that highly efficient click reactions occurred for polymer–polymer coupling. Successful quadruple click reactions were also confirmed by gel permeation chromatography. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of multiblock hyperbranched‐linear poly(ether sulfone) copolymers

Hyperbranched poly(ether sulfone) was prepared in the presence of an oligomeric linear poly(ether sulfone) to generate multiblock hyperbranched‐linear (LxHB) copolymers. The LxHB copolymers were prepared in a two‐step, one‐pot synthesis by first polymerizing AB monomer to generate a linear block of a desired molecular weight followed by addition of the AB₂ monomer in a large excess (19:1, AB₂:AB) to generate the hyperbranched block. NMR integration analysis indicates that AB₂:AB ratio is independent of the reaction time. Because the molecular weight still increases with reaction time, these results suggest that polymer growth continues after consumption of monomer by condensation into a multiblock architecture. The LxHB poly(ether sulfone)s have better thermal stability (10% mass loss > 343 vs. 317 °C) and lower T_g (200 vs. > 250 °C) than the hyperbranched homopolymer, higher T_g than the linear homopolymer (<154 °C), while little difference in the solubility character was observed between the two polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4785–4793, 2008     

Syntheses,characterization, and properties of multiblock copolymers consisting of polyisobutylene and poly(L‐lactide) segments

The syntheses of {‐poly(L ‐lactide) (PLLA)‐b‐polyisobutylene (PIB)‐}_n multiblock copolymers were accomplished for the first time by chain extension of PLLA‐b‐PIB‐b‐PLLA triblock copolymers. Well‐defined PLLA‐b‐PIB‐b‐PLLA triblock copolymers with predictable M_ns, low PDIs (1.10–1.18) and excellent blocking efficiencies were prepared by anionic ring‐opening polymerizations of L ‐lactide initiated with hydroxyallyl telechelic PIB (HO‐Allyl‐PIB‐Allyl‐OH) in toluene at 110 °C. The triblock copolymers were successfully chain extended with 4,4′‐methylenebis(phenylisocyanate) (MDI) to obtain the multiblock copolymers with good gravimetric yields of ～86 to 96%. The chain‐extended polymers were soluble in a range of common organic solvents. The block copolymers showed two glass transition temperatures in differential scanning calorimetric analysis for the PIB and PLLA blocks indicating microphase separation, which was supported by atomic force microscopy images. The as‐synthesized compression molded multiblock copolymers exhibited tensile strengths in the range of 8–24 MPa with elongations at break in the range of 2.5–400%. The static and dynamic mechanical properties showed a strong dependence on the relative PLLA content in the copolymer. The dynamic mechanical analysis also indicated microphase separation at higher PLLA compositions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3490–3505, 2009     

Block and star block copolymers by mechanism transformation. VI. Synthesis and characterization of A4B4 miktoarm star copolymers consisting of polystyrene and polytetrahydrofuran prepared by cationic ring‐opening polymerization and atom transfer radical polymerization

The synthesis of A₄B₄ miktoarm star copolymers, where A is polytetrahydrofuran (PTHF) and B is polystyrene (PSt), was accomplished with orthogonal initiators and consecutive cationic ring‐opening polymerization (CROP) and atom transfer radical polymerization (ATRP). The compound formed in situ from the reaction of 3‐{2,2‐bis[2‐bromo‐2‐(chlorocarbonyl) ethoxy] methyl‐3‐(2‐chlorocarbonyl) ethoxy} propoxyl‐2‐bromopropanoyl chloride [C(CH₂OCH₂CHBrCOCl)₄] with silver perchlorate was used to initiate the CROP of tetrahydrofuran. The obtained polymer contained four secondary bromine groups at the α position to the original initiator sites and was used to initiate the ATRP of styrene with a CuBr/2,2′‐bipyridine catalyst to form a C(PTHF)₄(PSt)₄ miktoarm star copolymer. The miktoarm copolymer was characterized by gel permeation chromatography and ¹H NMR. The macroinitiator C(PTHF)₄Br₄ was hydrolyzed to afford PTHF arms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2134–2142, 2001     

Synthesis and healing properties of poly(arylene ether sulfone)‐poly(alkyl disulfide) multiblock copolymers

A multiblock copolymer consisting of hard (poly(arylene ether sulfone)) and soft (poly(alkyl disulfide)) segments was successfully synthesized by oxidative coupling of the corresponding thiol‐terminated oligomers. Its structure was confirmed by ¹H and ¹³C NMR spectroscopy. The GPC data (M_w = 82,000, M_w/M_n = 2.7) and inherent viscosity (0.67 dL g⁻¹) indicated the formation of a high‐molecular‐weight multiblock copolymer, while AFM and DSC indicated a microphase‐separated morphology. Tensile testing of the multiblock copolymer films showed a large elongation at break, which is characteristic of microphase‐separated hard/soft multiblock copolymers. Over 90% of the elongation at break of damaged samples (notched or cut) was recovered by UV irradiation. The elongation recovery was proportional to the UV irradiation energy, and the high recovery was achieved by relatively weak irradiation (<170 J cm⁻²). The high content of disulfide bonds in the multiblock copolymer resulted in a lower self‐healing energy. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1358–1365     

Multiblock poly(4‐vinylpyridine) and its copolymer prepared with cyclic trithiocarbonate as a reversible addition–fragmentation transfer agent

The polymerization of 4‐vinylpyridine was conducted in the presence of a cyclic trithiocarbonate (4,7‐diphenyl‐[1,3]dithiepane‐2‐thione) as a reversible addition–fragmentation transfer (RAFT) polymerization agent, and a multiblock polymer with narrow‐polydispersity blocks was prepared. Two kinds of multiblock copolymers of styrene and 4‐vinylpyridine, that is, (ABA)_n multi‐triblock copolymers with polystyrene or poly(4‐vinylpyridine) as the outer blocks, were prepared with multiblock polystyrene or poly(4‐vinylpyridine) as a macro‐RAFT agent, respectively. GPC data for the original polymers and polymers cleaved by amine demonstrated the successful synthesis of amphiphilic multiblock copolymers of styrene and 4‐vinylpyridine via two‐step polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2617–2623, 2007     

Triple hydrogen‐bonding block copolymers via RAFT polymerization: Synthesis,vesicle formation,and molecule‐recognition behavior

Reversible addition fragmentation chain transfer polymerization afforded triple hydrogen‐bonding block copolymers (PBA‐b‐PDAD) with well‐controlled molecular weight and molecular weight distributions (1.2–1.4). The complexation via specific hydrogen bonding between these block copolymers in CHCl₃ provided an unprecedented approach for the formation of spherical vesicles. Atomic force microscopy and dynamic light‐scattering measurements revealed that the resultant polymeric vesicles were about 100 nm in radius. Triple hydrogen‐bonding interactions between maleimide and PBA‐b‐PDAD resulted in the dissociation of these spherical vesicles, facilitating the guest molecule recognition. The hydrogen‐bonding interaction between maleimide and the PBA‐b‐PDAD was further confirmed by ¹H NMR and FTIR spectra. These results indicated that these vesicles of triple hydrogen‐bonding block copolymer could be a potential new vehicle for molecular recognition. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1633–1638     

Enhancing the glass‐transition temperature of polyimide copolymers containing 2,2′‐bipyridine units by the coordination of nickel malenonitriledithiolate

Polyimide copolymers containing 2,2′‐bipyridine were synthesized and characterized. The glass‐transition temperatures (T_g's) of the polymers ranged from 260 to 300 °C. In contrast to most known organic chromophore‐containing polyimides, the polyimide copolymers in this study showed elevated T_g's (270–320 °C) after coordination with nickel malenonitriledithiolate inorganic chromophores. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 498–503, 2000     

Polytetrahydrofuran amphiphilic networks. I. Synthesis and characterization of polytetrahydrofuran acrylate ditelechelic and polyacrylamide‐l‐polytetrahydrofuran networks

A series of novel amphiphilic polyacrylamide‐l‐polytetrahydrofuran (PAm‐l‐PTHF) networks were prepared by the free‐radical copolymerization of hydrophobic ditelechelic polytetrahydrofuran acrylate (PTHFDA) with hydrophilic acrylamide. PTHFDA was synthesized by acrylation of the corresponding hydroxycapped PTHF with acrylic acid in cyclohexane. After acrylation, there was no significant difference in the molecular weights and molecular weight distributions between the original PTHF and the resulting PTHFDA. Network structures and compositions were characterized by elemental analyses, Fourier transform infrared, differential scanning calorimetry, scanning electron microscopy, and swelling data. The networks can swell both in organic solvents and in water, which indicates that they are amphiphilic. The swelling of the networks in different solvents is composition‐dependent. According to differential scanning calorimetry, scanning electron microscopy, and swelling tests, the networks have a microphase‐separated and bicontinuous morphology. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3812–3820, 2000     

Synthesis of block copolymers by the transformation of cationic polymerization into reversible atom transfer radical polymerization

Azo-containing polytetrahydrofuran (PTHF) obtained by cationic polymerization was used as a macroinitiator in the reverse atom transfer radical polymerization (RATRP) of styrene and methyl acrylate in conjunction with CuCl₂/2,2′-bipyridine as a catalyst. Diblock PTHF–polystyrene and PTHF–poly(methyl acrylate) were obtained after a two-step process. In the first step of the reaction, stable chlorine-end-capped PTHF was formed with the thermolysis of azo-linked PTHF at 65–70 °C in the presence of the catalyst. Heating the system at temperatures of 100–110 °C started the polymerization of the second monomer, which resulted in the formation of block copolymers. The decomposition behavior of the azo-linked PTHF and the structure of the block copolymers were determined by ¹H NMR and gel permeation chromatography (GPC). Kinetic studies and GPC analyses further confirmed the controlled/living nature of the RATRP initiated by the polymeric radicals. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2199–2208, 2002     

Synthesis of poly(tetrahydrofuran)‐b‐polystyrene block copolymers from dual initiators for cationic ring‐opening polymerization and atom transfer radical polymerization

A dual initiator (4‐hydroxy‐butyl‐2‐bromoisobutyrate), that is, a molecule containing two functional groups capable of initiating two polymerizations occurring by different mechanisms, has been prepared. It has been used for the sequential two‐step synthesis of well‐defined block copolymers of polystyrene (PS) and poly(tetrahydrofuran) (PTHF) by atom transfer radical polymerization (ATRP) and cationic ring‐opening polymerization (CROP). This dual initiator contains a bromoisobutyrate group, which is an efficient initiator for the ATRP of styrene in combination with the Cu(0)/Cu(II)/N,N,N′,N″,N″‐pentamethyldiethylenetriamine catalyst system. In this way, PS with hydroxyl groups (PS‐OH) is formed. The in situ reaction of the hydroxyl groups originating from the dual initiator with trifluoromethane sulfonic anhydride gives a triflate ester initiating group for the CROP of tetrahydrofuran (THF), leading to PTHF with a tertiary bromide end group (PTHF‐Br). PS‐OH and PTHF‐Br homopolymers have been applied as macroinitiators for the CROP of THF and the ATRP of styrene, respectively. PS‐OH, used as a macroinitiator, results in a mixture of the block copolymer and remaining macroinitiator. With PTHF‐Br as a macroinitiator for the ATRP of styrene, well‐defined PTHF‐b‐PS block copolymers can be prepared. The efficiency of PS‐OH or PTHF‐Br as a macroinitiator has been investigated with matrix‐assisted laser desorption/ionization time‐of‐flight spectroscopy, gel permeation chromatography, and NMR. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3206–3217, 2003     

Synthesis and properties of poly(sulfone‐arylate) copolymers

Poly(sulfone‐arylate) was synthesized in a reaction between dihydroxy polysulfone prepolymers and either diphenyl terephthalate or terephthaloyl chloride. The dihydroxy polysulfone prepolymers had molecular weights of 2000 and 4000 g/mol. The polymerization with diphenyl terephthalate was carried out at high temperature (280 °C) in the presence of a catalyst, whereas the polymerization with terephthalic chloride was conducted in solution at low temperature in the presence of an acid acceptor. High‐molecular weight copolymers (η_inh ～ 0.60 dL/g) could be obtained through both methods. The copolymers were characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance, DMA, and differential scanning calorimetry measurements and were found to exhibit high T_g values. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3904–3913, 2009