超临界 CO2 辅助制备 TiO2 外负载火山岩复合体及其光催化降解亚甲基蓝性能

 以钛酸丁酯为前驱体, 封堵的火山岩为载体, 通过超临界 CO₂ 辅助制备了 TiO₂ 外负载火山岩复合体, 并将其用于光催化降解亚甲基蓝反应, 考察了溶液 pH 值及催化剂浓度对反应性能的影响. 结果表明, TiO₂ 外负载火山岩复合体的光催化性能优于纯 TiO₂ 和 TiO₂ 体负载火山岩复合体. 这是由于外负载复合体对亚甲基蓝的高吸附性、小晶粒尺寸的 TiO₂ 颗粒以及吸附和光催化降解间的协同效应. 亚甲基蓝浓度为 1.5 mg/L, 溶液 pH 为 8, 催化剂浓度为 6.8 mg/L 时, 外负载 TiO₂ 火山岩复合体上亚甲基蓝降解速率最高, 且使用后的催化剂仍具有高的光催化活性.     

阳极氧化法制备TiO2纳米管及其光催化性能

纳米TiO₂对诸多环境污染物有显著的光催化降解作用,光催化已发展成为新型环境污染治理技术。本文采用阳极氧化法制备出TiO₂纳米管,对比了四种电解液组成(A氟化铵+硫酸铵+水;B氟化铵+硫酸铵+乙酸+水;C氟化铵+硫酸铵+甘油+水;D氢氟酸+二甲基亚砜(DMOS)+乙醇)对催化剂表面形貌及光催化性能的影响。结果表明,电解液A和C都制备出了形貌清晰的TiO₂纳米管,管径约为60~74 nm。样品经400 ℃煅烧,TiO₂晶型主要为锐钛矿相;经500 ℃煅烧,出现少量金红石相;经700 ℃煅烧,晶型全部为金红石相。具有良好形貌的TiO₂纳米管同时具有良好的紫外光吸收能力。当亚甲基蓝初始浓度为10 mg·L^-1,经500 ℃煅烧的TiO₂纳米管光催化活性最佳,光照30 min亚甲基蓝的降解率达89.98%。亚甲基蓝光催化降解反应符合一级反应动力学,反应速率常数为0.079 30。     

部分还原氧化石墨烯/二氧化钛复合材料的水热合成及其光催化活性

采用水热法以Hummers氧化法制备的氧化石墨和钛酸四丁酯为原料制备了部分还原的氧化石墨烯/二氧化钛(RGO/TiO₂)复合光催化剂, 并研究了该复合材料在可见光以及紫外光下对亚甲基蓝的光催化降解活性.结果表明, 通过改变反应温度和氧化石墨加入量可以调控TiO₂的晶相组成及其在复合材料中的分散性; 在水热反应过程中氧化石墨烯发生了部分还原; 所制备的RGO/TiO₂复合材料的可见光和紫外光催化活性均高于纯TiO₂; 部分还原的氧化石墨烯在复合材料中担当载体和电子受体, 同时可以使TiO₂的初始吸收边向可见光区域红移, 增强了TiO₂在可见光区域的吸收, 能有效提高对目标污染物的吸附性和光催化降解活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

Synthesis and Characterization of TiO2/YFeO3 and Its Photocatalytic Oxidation of Gaseous Benzene

YFeO₃ was prepared by coprecipitation method and citric acid method, and TiO₂/YFeO₃ heterosystem photocatalysts were synthesized by loading TiO₂ sol on the surface of YFeO₃via sol-gel method. Their photocatalytic activities were evaluated by the decomposition of gaseous benzene under UV light illumination. The prepared photocatalysts were characterized by nitrogen adsorption-desorption, X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and UV-Vis diffuse reflectance spectroscopy. Results revealed that the heterosystem photocatalysts prepared by coprecipitation method showed higher activity, and the maximum conversion of benzene could reach 44.7% within 180 min. The YFeO₃ samples prepared from coprecipitation method and citric acid method were absolutely in orthorhombic phase. The deposited titania was dispersed on the surface of carrier and a certain interaction existed between TiO₂ and YFeO₃. The two heterosystems photocatalysts had narrow band-gap energies.     

紫外光照射下丙炔光催化水解反应的研究 Ⅰ．纳米二氧化钛光催化剂的性能

 采用5种不同的纳米二氧化钛为光催化剂,考察了它们在丙炔水解反应中的光催化活性,并用X射线衍射和漫反射紫外－可见吸收光谱技术进行了表征．研究了催化剂表面物理化学性质与在丙炔光催化水解反应中的构效关系．实验结果表明,纳米二氧化钛光催化剂能够引发丙炔的光催化水解反应,生成乙烷和乙烯等产物;锐钛矿相纳米二氧化钛具有较高的光催化活性,在晶型相同的情况下,影响光催化活性的主要因素是催化剂的粒径和比表面积．     

硫和银共掺杂介孔TiO2的制备表征及光催化活性

以P123为模板,以钛酸四正丁酯、硝酸银和硫脲为原料采用模板法制备了一系列硫和银共掺杂介孔TiO2光催化材料。利用扫描电子显微镜（SEM）、X射线衍射（XRD）、BET和紫外-可见光谱（UV-Vis）等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征。以甲基橙溶液的光催化降解为模型反应, 考察了不同掺杂量的样品在紫外和可见光下的光催化性能。结果表明：用模板法制备的共掺杂介孔TiO2光催化材料在紫外和可见光条件下较纯介孔TiO2和单掺杂介孔TiO2对甲基橙溶液具有更好的光催化降解效果, 且硫和银的掺杂量及样品焙烧温度显著影响该材料的催化性能。当硫掺杂量为2%（mol）和银掺杂量为1%（mol）,在500℃焙烧2 h所得光催化材料的催化性能最佳, 4 h即可使甲基橙的降解率达98.8%,重复使用4次仍可使甲基橙的降解率保持在87.5%以上。因此, 以该模板合成法, 通过硫和银的共掺杂有望使TiO2成为一种低或无能耗、高活性的绿色环保型催化材料。     

A simple route for the preparation of Eu, N-codoped TiO2 nanoparticles with enhanced visible light-induced photocatalytic activity

A simple route has been developed for the synthesis of europium, nitrogen-codoped titania photocatalysts under mild conditions (i.e., low temperature, < or = 348 K, and ambient pressure). The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and diffuse reflectance spectra (DRS) analyses. The results showed that the codoped photocatalyst with a spheroidal shape exhibited a smaller size than the undoped titania. The transformation from anatase to rutile was suppressed by doping with Eu and N atoms. Furthermore, the absorbance spectra of Eu, N-codoped TiO(2) exhibited a significant red shift to the visible region. The photocatalytic activity of Eu, N-codoped TiO(2) was evaluated by photodegradation of the dye reactive brilliant red X-3B under visible light. This codoped sample exhibited enhanced photocatalytic activity compared to N-doped TiO(2), pure TiO(2), and P25.     

Synergistic effects of sulfation and Fe-doping on the photocatalysis of titania

Fe-doped sulfated titania photocatalysts were prepared by one-step thermal hydrolysis of industrial titanyl sulfate and characterized using XRD, FT-IR, UV–Vis DRS, and N₂ adsorption–desorption techniques. The effects of the volume ratio of pre-adding water to TiOSO₄ on the structure of the titania photocatalysts were investigated. The photocatalytic activities of Fe-doped sulfated titania samples were evaluated using the photooxidation of methylene blue in aqueous solutions under UV light irradiation. The results indicate that Fe-doping induces the red shift of the absorption edge to the visible light range. Meanwhile, sulfur species in the form of sulfate are incorporated into the network of Ti–O–Ti and coordinated to titania in bidentate models, which can effectively promote the separation of the photogenerated electrons and holes. Synergistic effects of both are beneficial for improving the photocatalytic activity of the Fe-doped sulfated titania photocatalysts.     

Simple route to monodispersed silica-titania core-shell photocatalysts

A monodispersed silica-titania core-shell photocatalyst was synthesized via a sol-gel route without the need of pH adjustment, cationic polyelectrolytes, or surfactants in a process where silica spheres were impregnated with hydrolyzed titanium tetrabutoxide, incubated at room temperature, and then condensed using an ethanol/water (1:1) solvent. Four coating cycles in a 10% v/v titania sol produced homogeneous titania shells. The quality of catalysts was assessed quantitatively using Rietveld analysis of powder X-ray diffraction patterns combined with X-ray fluorescence spectrometry. During calcination, the anatase-to-rutile transformation was delayed to 1000 degrees C, which is approximately 300 degrees C higher than usually observed. The thermal stability and surface area of titania were enhanced through the slow crystal growth of anatase. The photocatalytic activity of the core-shell photocatalysts calcined at 400-600 degrees C was found to be proportional to the thickness of titania but did not directly correlate with the surface area.     

Influence of synthesis methods on zirconium doped titania photocatalysts

Synthesis of various zirconium doped titania based photocatalysts were carried out by adapting different synthetic strategies. Doping is done on commercially available anatase titania, sol-gel titania and template mediated sol gel titania. A comparative study of the various prepared photocataysts was done using physico-chemical characterization techniques such as X-ray diffraction (XRD), surface area- pore volume measurements, UV-VIS Diffuse reflectance spectra (DRS), elemental analysis (XRF) and transmission electron microscopic (TEM) studies. The effect of zirconium and preparation methods on the photocatalytic degradation of methylorange is studied extensively. Both the surface properties and photo activity of zirconium doped titania were found to have a great dependence on the preparation methods. Among the different photocatalytic systems, the catalyst prepared by doping in the presence of urea template was found to produce a maximum photodegradation of 97.5%.     

纳米级TiO2粉体的制备研究——Ⅱ.絮凝剂及其浓度的影响

采用溶胶-凝胶-超临界流体干燥(SCFD)法制备纳米级TiO₂超细粉，详细考察了不同絮凝剂及其浓度对TiO₂织构和结构性质的影响。结果表明，利用强碱溶液作为絮凝剂，浓度为5 mol·L^-1是制备大孔高比表面TiO₂超细粉较为适宜的条件。     

Absorption and action spectra analysis of ammonium fluoride-doped titania photocatalysts

The photocatalytic behaviour of a series of ammonium fluoride (NH(4)F)-doped titania (TiO(2)) photocatalysts was investigated in the decomposition of acetic acid in aqueous suspensions and in the gas phase mineralization of acetaldehyde. Very similar photocatalytic activity trends, usually increasing with increasing the calcination temperature for a given nominal dopant amount, were obtained for the two test reactions. Moderately doped TiO(2) calcined at 700 °C, consisting of pure anatase, was the best performing photocatalyst in both reactions. The photocatalytic oxidation of acetic acid was investigated systematically as a function of irradiation wavelength, by collecting so-called action spectra. By comparing the shapes of the action spectra with those of the absorption spectra of the investigated photocatalysts a model is proposed, based on spectral features deconvolution, which allows a clear distinction between inactive light absorption and effective photoactivity in acetic acid decomposition.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.