Cu-Doped MoSi2N4 Monolayer as a Potential NH3 Sensor

Cu doped MoSi₂N₄ monolayer (Cu-MoSi₂N₄) was firstly proposed to analyze adsorption performances of common gas molecules including O₂, N₂, CO, NO, NO₂, CO₂, SO₂, H₂O, NH₃ and CH₄ via density functional theory (DFT) combining with non-equilibrium Green's function (NEGF). The electronic transport calculations indicate that Cu-MoSi₂N₄ monolayer has high sensitivity for CO, NO, NO₂ and NH₃ molecules. However, only NH₃ molecule adsorbs on the Cu-MoSi₂N₄ monolayer with moderate strength (−0.55 eV) and desorbs at room temperature (2.36×10⁻³ s). Thus, Cu-MoSi₂N₄ monolayer is demonstrated as a potential NH₃ sensor.     

Organolithium complex as a gas sensing material for oxides from ab initio calculations and molecular dynamics simulations

Gas sensing study of C₂H₄Li complex toward oxides viz. CO, CO₂, NO, NO₂, SO, and SO₂ gas molecules has been carried out using ab initio method. Different possible configurations of gas molecule adsorption on C₂H₄Li complex are considered. The structural parameters of most stable configuration of gas molecule adsorbed complexes are thoroughly analysed. Electronic properties are studied using total density of states (DOS) plot. Charge transferred between the gas molecule and the substrate is studied using NBO charge analysis. Gas sensing of all the six gas molecules is possible at ambient conditions. Atom centred density matrix propagation (ADMP) molecular dynamics simulations confirmed that all the gas molecules remain adsorbed on C₂H₄Li complex at room temperature during the simulation. This study suggests that the C₂H₄Li complex acts as a novel gas sensing material for CO, CO₂, NO, NO₂, SO, and SO₂ gas molecules at ambient conditions, below room temperature as well as at high pressure.     

Density Functional Theory Studies on the Adsorption of NH2NO2 on Al13 Cluster

Density functional theory method with full geometry optimization was used to study the adsorption of nitroamine (NH₂NO₂) on Al₁₃ cluster. Both dissociative and nondissociative adsorption structures were predicted with different NH₂NO₂ molecule orientations on Al₁₃ cluster surfaces. In dissociative chemisorption, the main decomposition products of NH₂NO₂ are O atom(s) and NH₂NO or NH₂N species. The O atoms being ruptured from the N?CO bond form strong Al?CO bonds with the neighboring Al around the adsorbed sites. In addition, the species obtained as a result of O atom elimination remains bonded to the surface. The largest adsorption energy is ?737.66?kJ/mol when the NH₂NO₂ molecule decomposes into two O atoms and a NH₂N fragment. For nondissociative adsorption, the seriously deformed nitroamine forms various N?CO?CAl bonding configurations with Al. The significant charge transfer occurs for all adsorption configurations. The most charge transfer is 2.068 e from the Al cluster surface to the fragments of the decomposed NH₂NO₂. The change of the electronic structures is obvious due to the adsorption or dissociation of NH₂NO₂ molecule. Nitroamine readily oxidizes the aluminum surface of the Al₁₃ cluster.     

利用温度跃升傅立叶变换红外原位分析技术对斯蒂酚酸碳酰肼和斯蒂酚酸氨基脲快速热解反应的研究

Flash pyrolysis of （CHZ）2TNR and （SCZ）2TNR was conducted by T-jump/FTIR spectroscopy under 0.1 MPa Ar atmosphere. The results show that eleven IR-active gas products obtained during flash pyrolysis process of the two title compounds are NO, CO, HCN, NH3, NO2, N2O, HNCO, HNO2, CO2, H2O and HCHO, of which NO and CO are the main gas products. The molar fraction of the individual product in the pyrolysis gas mixture was described as a function of time. At least some of the NO2, N2O and H2O can result from the oxidization reaction of NH3 during flash pyrolysis of （CHZ）2TNR. It can be concluded that the two compounds are not worthy of further in-depth consideration of the adoption in detonators as eco-friendly primary explosive, and should not be used as gas generation composition of automobile crash airbag system taking into account the toxicity.     

Density functional theory study on sensing properties of g-C3N4 sheet to atmospheric gasses: Role of zigzag and armchair edges

The ability of the polymer-based graphitic carbon nitride (g-C₃N₄) as a gas sensor toward NO, NO₂, CO, CO₂, SO₂, SO₃, and O₂ gasses is assessed using density functional theory (DFT) calculations in terms of energetic and electronic transport characteristics. In particular, this study is aimed to explore the role of zigzag and armchair edges of the g-C₃N₄ sheet on sensing performances. The electronic properties of adsorption systems, such as Bader charge analysis, band gaps, work function, and density of states (DOS), are used to understand the interaction between the adsorbed gas molecules and the g-C₃N₄ sheet. Our calculated results indicate that SOx (SO₃ and SO₂) gasses have higher adsorption energies on the g-C₃N₄ sheet than other gasses. Furthermore, the transport properties, such as current–voltage (I-V) and resistance-voltage (R-V) curves along the zigzag and armchair directions are calculated using the non-equilibrium Green's function (NEGF) method to understand the performance of the g-C₃N₄ sheet as a prominent conductive/resistive sensor. The I-V/R-V results indicate that the zigzag g-C₃N₄ sheet has excellent sensing ability toward SOx gasses at low applied voltages. However, the presence of H₂O degrades the sensing performance of the armchair g-C₃N₄ sheet. Theoretical recovery time has also been calculated to evaluate the reusability of g-C₃N₄ sheet-based gas sensors. Our results reveal that the zigzag g-C₃N₄ sheet-based sensing device has a remarkably high sensitivity (>300%) and selectivity toward SOx gasses and has the potential to work in a complex environment.     

Adsorption of NO and CO and specific features of their interaction on the Pt(100) surface

This article presents an analytical review of the author’s results and the literature concerning the nature of species resulting from NO and CO adsorption on the unreconstructed (1 × 1) and reconstructed hexagonal (hex) Pt(100) surfaces, including specific features of the reactions between these species. At 300 K, both surfaces adsorb NO and CO mainly in their molecular states. When adsorbed on Pt(100)-1 × 1, the NO_ads and CO_ads molecules are uniformly distributed on the surface. Under the same conditions, the hexagonal surface undergoes adsorption-induced reconstruction with the formation of NO_ads/1 × 1 and CO_ads/1 × 1 islands, which are areas of the unreconstructed phase saturated with adsorbed molecules and surrounded with the adsorbate-free hex phase. In adsorption on structurally heterogeneous surfaces containing both hex and 1 × 1 areas, the 1 × 1 and hex phases are occupied in succession, the latter undergoing reconstruction into the 1 × 1 phase. The reaction between NO and CO on the unreconstructed surfaces occurs even at room temperature and results in the formation of N₂ and CO₂ in quantitative yield. On the hexagonal surface, a stable layer of adsorbed molecules as (NO_ads + CO_ads)/1 × 1 mixed islands forms under these conditions. Above 350 K, the reaction in the mixed islands is initiated by the desorption of small amounts of the initial compounds, and this is followed by rapid self-acceleration leading to a surface explosion yielding N₂, CO₂, and N₂O (minor product). These products show themselves as very narrow desorption peaks in the temperature-programmed reaction spectrum.     

用T-jump/FTIR研究MnCP、NiCP和PbCP的快速热分解(英)

0IntroductionCarbohydrazideisahydrazinederivativewithwhitecrystalofstrongreducingbehaviors.Becauseithasmanycoordinationatoms(fournitrogenatomsandoneoxygenatom),carbohydrazidecan,therefore,beusedasmultidentateligand.Itscoordinationcom鄄poundiswidelyusedint…     

The Adsorption Behavior of Gas Molecules on Co/N Co–Doped Graphene

Herein, we have used density functional theory (DFT) to investigate the adsorption behavior of gas molecules on Co/N₃ co–doped graphene (Co/N₃–gra). We have investigated the geometric stability, electric properties, and magnetic properties comprehensively upon the interaction between Co/N₃–gra and gas molecules. The binding energy of Co is −5.13 eV, which is big enough for application in gas adsorption. For the adsorption of C₂H₄, CO, NO₂, and SO₂ on Co/N–gra, the molecules may act as donors or acceptors of electrons, which can lead to charge transfer (range from 0.38 to 0.7 e) and eventually change the conductivity of Co/N–gra. The CO adsorbed Co/N₃–gra complex exhibits a semiconductor property and the NO₂/SO₂ adsorption can regulate the magnetic properties of Co/N₃–gra. Moreover, the Co/N₃–gra system can be applied as a gas sensor of CO and SO₂ with high stability. Thus, we assume that our results can pave the way for the further study of gas sensor and spintronic devices.     

Experimental characterization of gaseous species emitted by the fast pyrolysis of biomass and polyethylene

This study aims to experimentally characterize the carbonaceous and nitrogenous species, from the flash pyrolysis of millet stalks and polyethylene plastic bags, using the device of the tubular kiln, coupled to two gas analyzers: Analyzer Fourier Transform Infrared (FTIR) and an analyzer Infrared Non-Dispersive (IRND). Gaseous products analyzed are: CH₄, C₂H₂, C₂H₄, C₃H₈, C₆H₆, CO, CO₂, NO₂, NO, N₂O, HCN and NH₃. Whatever the temperature of thermal degradation, the pyrolysis shows us that in terms of mass:

• •For the millet stalks, the gaseous compounds are formed mainly CO and CO₂ to the carbonaceous species, HCN and NH₃, for the nitrogenous species analyzed;
• •As regards the polyethylene bags, hydrocarbons for carbonaceous species and HCN, NH₃ and NO₂ for the nitrogenous species, are most abundant.

In addition, the results suppose that in our experimental conditions, the hydrocarbon which is involved primarily in the formation of CO is ethylene C₂H₄. At the end of this characterization, we determined the rate of carbon and nitrogen found in the volatile gas. With millet stalks we have about 45% of volatile carbon and 15% of the nitrogen of fuel that are found in gaseous products. The results obtained with the plastic bags give 68% carbon and 15% nitrogen found in the nitrogenous species analyzed.     

A Hydrogen‐Bonded Organic Framework (HOF) with Type IV NH3 Adsorption Behavior

An S‐shaped gas isotherm pattern displays high working capacity in pressure‐swing adsorption cycle, as established for CO₂, CH₄, acetylene, and CO. However, to our knowledge, this type of adsorption behavior has not been revealed for NH₃ gas. Herein, we design and characterize a hydrogen‐bonded organic framework (HOF) that can adsorb NH₃ uniquely in an S‐shape (type IV) fashion. While conventional porous materials, mostly with type I NH₃ adsorption behavior, require relatively high regeneration temperature, this platform which has significant working capacity is easily regenerated and recyclable at room temperature.     

Formation Mechanism,Geometric Stability and Catalytic Activity of a Single Iron Atom Supported on N-Doped Graphene

Based on density functional theory (DFT) calculations, the formation geometries, stability and catalytic properties of single-atom iron anchored on xN-doped graphene (xN-graphene-Fe, x=1, 2, 3) sheet are systemically investigated. It is found that the different kinds and numbers of gas reactants can effectively regulate the electronic structure and magnetic properties of the 3 N-graphene-Fe system. For NO and CO oxidation reactions, the coadsorption configurations of NO/O₂ and CO/O₂ molecules on a reactive substrate as the initial state are comparably analyzed. The NO oxidation reactions through the Langmuir–Hinshelwood (LH) and Eley-Rideal (ER) mechanisms have relatively smaller energy barriers than those of the CO oxidation processes. In comparison, the preadsorbed 2NO reacting with 2CO molecules (2NO+2CO→2CO₂+N₂) through ER reactions (<0.4 eV) are energetically more favorable processes. These results can provide beneficial references for theoretical studies on NO and CO oxidation and designing graphene-based catalyst for toxic gas removal.     

Physicochemical properties of ceramic tape involving Ca<Subscript>0.05</Subscript> Ba<Subscript>0.95</Subscript> Ce<Subscript>0.9</Subscript>Y<Subscript>0.1</Subscript>O<Subscript>3</Subscript> as an electrolyte designed for electrolyte-supported solid oxide fuel cells (IT-SOFCs)

Energetic materials such as a mixture of guanidine nitrate (GN)/basic copper nitrate (BCN) are used as gas generators in automotive airbag systems. However, at the time of the airbag inflation, the gas generators release toxic combustion gases such as CO, NH₃, and NO_x. In this study, we investigated the combustion and thermal decomposition behaviors of GN/BCN mixture, focusing primarily on their exhaust gas composition. As a result, when the exhaust gas of the combustion under constant pressure in an inert gas stream was analyzed using a detection tube, the amount of NO_x (mainly NO) yielded greater decrease with increasing atmospheric pressure as compared to the amounts of CO and NH₃. Thus, provided GN/BCN is ignited in a closed container, a large amount of NO_x is presumed to have been released during the initial stage of combustion, which yielded comparatively low pressure. Results of the thermogravimetry–differential scanning calorimetry–Fourier transform infrared spectroscopy (TG/DSC/FTIR) indicated that the GN/BCN mixture caused endothermic decomposition at 170 °C and exothermic decomposition at 208 °C, which was accompanied by 66% mass loss. The decomposition gases, CO₂, N₂O, and H₂O, were detected via FTIR spectrum. Because N₂O was not detected in the combustion gas, it was suggested that the detected N₂O was generated at a low temperature and decomposed in high-temperature combustion.     

Ambient Electrosynthesis of Urea with Nitrate and Carbon Dioxide over Iron-Based Dual-Sites

The development of efficient electrocatalysts to generate key *NH₂ and *CO intermediates is crucial for ambient urea electrosynthesis with nitrate (NO₃⁻) and carbon dioxide (CO₂). Here we report a liquid-phase laser irradiation method to fabricate symbiotic graphitic carbon encapsulated amorphous iron and iron oxide nanoparticles on carbon nanotubes (Fe(a)@C-Fe₃O₄/CNTs). Fe(a)@C-Fe₃O₄/CNTs exhibits superior electrocatalytic activity toward urea synthesis using NO₃⁻ and CO₂, affording a urea yield of 1341.3±112.6 μg h⁻¹ mg_cat⁻¹ and a faradic efficiency of 16.5±6.1 % at ambient conditions. Both experimental and theoretical results indicate that the formed Fe(a)@C and Fe₃O₄ on CNTs provide dual active sites for the adsorption and activation of NO₃⁻ and CO₂, thus generating key *NH₂ and *CO intermediates with lower energy barriers for urea formation. This work would be helpful for design and development of high-efficiency dual-site electrocatalysts for ambient urea synthesis.     

Structural and Magnetic Study of N2, NO,NO2, and SO2 Adsorbed within a Flexible Single‐Crystal Adsorbent of [Rh2(bza)4(pyz)]n

The crystalline one‐dimensional compound, [Rh^II₂(bza)₄(pyz)]_n ( 1 ) (bza=benzoate, pyz=pyrazine) demonstrates gas adsorbency for N₂, NO, NO₂, and SO₂. These gas‐inclusion crystal structures were characterized by single‐crystal X‐ray crystallography as 1 ?1.5 N₂ (298 K), 1 ?2.5 N₂ (90 K), and 1 ?1.95 NO (90 K) under forcible adsorption conditions and 1 ?2 NO₂ (90 K) and 1 ?3 SO₂ (90 K) under ambient pressure. Crystal‐phase transition to the P space group that correlates with gas adsorption was observed under N₂, NO, and SO₂ conditions. The C2/c space group was observed under NO₂ conditions without phase transition. All adsorbed gases were stabilized by the host lattice. In the N₂, NO, and SO₂ inclusion crystals at 90 K, short interatomic distances within van der Waals contacts were found among the neighboring guest molecules along the channel. The adsorbed NO molecules generated the trans‐NO???NO associated dimer with short intermolecular contacts but without the conventional chemical bond. The magnetic susceptibility of the NO inclusion crystal indicated antiferromagnetic interaction between the NO molecules and paramagnetism arising from the NO monomer. The NO₂ inclusion crystal structure revealed that the gas molecules were adsorbed in the crystal in dimeric form, N₂O₄.     

QM/MM study of the interaction between zigzag SnC nanotube and small toxic gas molecules

Adsorptions of small toxic molecules such as CO, N₂, HCN, SO₂, H₂CO, and NH₃ on a single‐walled (6,0) SnC nanotube (SnCNT) are investigated using Quantum Mechanics/Molecular Mechanics (QM/MM) methodology. The calculations are carried out at the B3LYP/6‐311++G(d,p)//LANL2DZ:UFF level of theory. The high layer of the model consists of a pyrene‐type ring on the nanotube surface as the adsorption site, where one gas molecule is allowed to interact. Conversely, for the adsorption of the two molecules, a larger site like a coronene ring is used for the high layer. Adsorption energy, Gibbs free energy change, Mulliken charge transfer, and total electron‐density maps are computed in each case. The adsorption strength of the gas molecule on the SnCNT surface is also analyzed from the density of states projected to different atoms (PDOS) of the nanotube–adsorbate complexes. The adsorptions of CO and N₂ on the (6,0) SnCNT surface require to cross potential barriers, and the corresponding transition structures are identified by ONIOM‐IRC calculations. For the remaining four molecules, the processes of adsorption are predicted to be barrier‐less. The calculations for the adsorption of H₂CO on (5,0) and (7,0) SnCNT surfaces are extended to study the effect of the size of the nanotube. Results for the adsorption of a single molecule on (6,0) SnCNT using B3LYP functional are compared with those obtained from a dispersion corrected functional such as M06‐2X. © 2015 Wiley Periodicals, Inc.     

New catalysts and adsorbents on the basis of the InSb-CdTe semiconducting system

The acid-base properties of solid solutions and binary components of the InSb-CdTe system were studied by IR spectroscopy, pH isoelectric point measurements, and conductometric titration; adsorption properties with respect to CO, O₂, NO₂, NH₃, CO + O₂, and NO₂ + NH₃, by piezoquartz microweighing; and catalytic properties in the oxidation of carbon(II) oxide and reduction of nitrogen(IV) oxide with ammonia, by the pulsed and circulation flow methods. The nature, strength, and concentration of acid centers were determined. Changes in the concentration of acid centers under the action of gases (NO₂ and NH₃), gamma irradiation, and composition variations were estimated. The experimental dependences, thermodynamic and kinetic adsorption characteristics, the electrophysical, acid-base, and other physicochemical characteristics of the adsorbents, and adsorption characteristic-composition phase diagrams were analyzed taking into account the electronic nature of adsorbate molecules to determine the mechanism and characteristics of adsorption processes depending on the conditions of adsorption and the composition of the system. The results of adsorption studies were used to preliminarily determine the temperature regions of the occurrence and the mechanism of the reactions studied. A shock mechanism was suggested. Separate components (predominantly, solid solutions) of the InSb-CdTe system showed high catalytic activity at comparatively low temperatures. Along with behavior common to the system and its binary compounds (InSb and CdTe), solid solutions exhibited features characteristic of multi-component systems. These were the presence of extrema in the pH_iso-composition, adsorption characteristic-composition, and catalytic activity-composition diagrams. The use of these diagrams allowed us to discover system components most active with respect to the gases and reactions studied and create high-sensitivity and selective sensors and high-activity and selective catalysts on the basis of these components.     

A DFT study on the structural and electronic properties of small toxic gases on B- and Al- doped C<Subscript>20</Subscript> fullerene

The structural and electronic properties of semiconducting BC₁₉ and AlC₁₉ heterofullerenes as adsorbents for toxic small gas molecules (H₂S and SO₂) are determined by DFT. Structural parameters, energy gaps, natural population analysis, partial density of state, dipole moments, and vibrational frequencies were extracted. The adsorption process and sensitivity to the gases are increased by doping with B or Al. The results show that AlC₁₉ is the most sensitive structure. The good sensing of AlC₁₉ is related to high charge transfer upon gas adsorption. Adsorption of the H₂S on the BC₁₉ has negligible effects on the electronic properties, to be categorized as “harmless adsorption”. H₂S is weakly adsorbed on BC₁₉ and AlC₁₉. The H₂S and SO₂ molecules act as electron donating and electron withdrawing molecules, respectively. Notably, the adsorption processes are highly exothermic. In general, BC₁₉ is more reactive than C20 and AlC₁₉ is the most reactive cage. This provides a theoretical basis to fabricate B- and Al-doped C20-based gas sensors.     

Adsorption of small molecules on helical gold nanorods: A relativistic density functional study

We study the adsorption of a variety of small molecules on helical gold nanorods using relativistic density functional theory. We focus on Au₄₀ which consists of a central linear strand of five gold atoms with seven helical strands of five gold atoms on a coaxial tube. All molecules preferentially adsorb at a single low‐coordinated gold atom on the coaxial tube at an end of Au₄₀. In most cases, there is significant charge transfer (CT) between Au₄₀ and the adsorbate, for CO and NO₂, there is CT from the Au₄₀ to adsorbate while for all other molecules there is CT from the adsorbate to Au₄₀. Thus, Au₄₀‐adsorbate can be described as a donor–accepter complex and we use charge decomposition analysis to better understand the adsorption process. We determine the adsorption energy order to be C₅H₅N >NO₂ > CO > NH₃ > CH₂?CH₂ > CH₂?CH? CHO > NO > HC?CH > H₂S > SO₂ > HCN > CH₃OH > H₂C?O > O₂ > H₂O > CH₄ > N₂. We find that the Au? C, Au? N, Au? S, and Au? O bonds are surprisingly strong, with clear implications for reactivity enhancement of the adsorbate. The Au? H bond is relatively weak but, for interactions via an H atom that is bonded to a carbon atom (e.g., CH₄), we find that there is large charge polarization of the Au? H? C moiety and partial activation of the inert C? H bond. Although the Au? S and Au? O bonds are generally weaker than the Au? C and Au? N bonds, we find that adsorption of H₂S or H₂O causes greater distortion of Au₄₀ in the binding region. However, the degree of distortion is small and the helical structure is retained, demonstrating the stability of the helical Au₄₀ nanorod under perturbations. © 2014 Wiley Periodicals, Inc.     

The Study of Nitric Oxide Adsorption and the Mechanism of Surface “Explosions” in the Reaction of CO + NO on Pt(100) and Pd(110) Single Crystal Surfaces

High resolution electron energy loss spectroscopy (HREELS), temperature-programmed desorption (TPD) and temperature-programmed reaction (TPR) were used to study NO adsorption and the reactivity of CO_ads and NO_ads molecules on Pd(110) and Pt(100) single crystal surfaces. Compared to the Pt(100)-(1 × 1) surface, the unreconstructed Pt(100)-hex surface is chemically inert toward NO dissociation into N_ads and O_ads atoms. When a mixed adsorbed CO_ads + NO_ads layer is heated, a so-called surface explosion is observed when the reaction products (N₂, CO₂, and N₂O) synchronously desorb in the form of sharp peaks with a half-width of 7-20 K. The shape specificity of TPR spectra suggests that the vacancy mechanism consists of the autocatalytic character of the reaction initiated by the formation an initial concentration of active sites due to partial desorption of molecules from the CO_ads + NO_ads layer upon heating to high temperatures. Kinetic experiments carried out on the Pd(110) surface at a constant reaction pressure and a linear increase in the temperature confirm the explosive mechanism of the reaction NO + CO.