曲克芦丁在羧基化单壁碳纳米管修饰电极上的电化学氧化

研制了羧基化单壁碳纳米管修饰玻碳电极( SWCNTs - COOH/GCE).用交流阻抗谱法(EIS)和扫描电镜( SEM)研究了电极膜性能,应用循环伏安法(CV)考察了曲克芦丁在修饰电极上的电化学行为.结果表明,SWCNTs - COOH修饰电极对曲克芦丁的氧化有良好的电催化活性,其氧化反应为单电子单质子过程,结合恒...     

蒿甲醚在单壁碳纳米管修饰电极上的电催化还原

研制了单壁碳纳米管(SWCNTs)修饰玻碳电极。用交流阻抗谱法(EIS)和扫描电镜(SEM)研究了电极膜性能,应用循环伏安法(CV)、计时库仑法(CC)、计时电流法(CA)研究了蒿甲醚在修饰电极上的电化学行为。结果表明,SWCNTs修饰电极对蒿甲醚的还原有良好的电催化活性,其还原反应为双电子过程,电极反应的扩散系数及速率常数分别为6·67×10-4cm2·s-1及8·54×10-2mol·L-1·s-1。在优化实验条件下,还原峰的峰电位位于-0·85V,其峰电流与蒿甲醚浓度在6·71×10-7~2·45×10-4mol·L-1范围内呈良好线性,检出限达4·02×10-7mol·L-1,相对标准偏差(n=10)为4·2%,可用于蒿甲醚样品的含量测定。     

热处理碳纸电极上VO2+/VO+2氧化还原动力学

在不同温度下热氧化处理碳纸, 用循环伏安、极化曲线和交流阻抗方法研究碳纸电极上VO2+/VO+2氧化还原动力学. 循环伏安和极化曲线结果表明, 随着热处理温度的升高, VO2+/VO+2氧化还原反应的速率常数及交换电流增大. 建立了VO2+/VO+2氧化还原反应的交流阻抗等效电路模型. 拟合结果表明, 热处理增大了碳纸电极表面的双电层电容, 减小了VO2+/VO+2氧化还原反应的电荷转移电阻. 用循环伏安和交流阻抗两种方法求得的VO2+和VO+2的扩散系数基本相同, 表明所构建的交流阻抗等效电路模型与电极反应过程相符合.     

基于纳米ZnO/壳聚糖复合膜DNA电化学传感器用于HIV基因的免标记检测

以室温固相合成法制备纳米ZnO,通过壳聚糖(CHIT)的成膜效应将纳米ZnO固定在玻碳电极(GCE)表面,制得的ZnO/CHIT/GCE电极成为DNA固定和杂交的良好平台。DNA的固定和杂交通过电化学交流阻抗进行表征。以电化学交流阻抗免标记法检测目标DNA,固定于电极表面的DNA探针与目标DNA杂交后使电极表面的电子传递电阻增大,以此作为检测信号可以高灵敏度地测定目标DNA。电化学阻抗谱检测人类免疫缺陷病毒(HIV)基因片段的线性范围为2.0×10-11~2.0×10-6mol/L,检出限为2.0×10-12mol/L。     

Pt/纳米碳管空气电极氧还原反应的电催化性能

以不同质量比的铂、纳米碳管、活性炭为催化层制备空气电极并测定其稳态极化曲线和交流阻抗.研究发现,纳米碳管经硝酸处理后其氧还原反应性能得到提高,特别是将表面氧化后再沉积Pt,对氧的电还原反应影响更显著.以质量比4∶1的活性炭/纳米碳管载Pt制备的空气电极,在过电位ηc为500～600mV下,氧还原电流可达600～700mA·cm-2.EIS测试表明,纳米碳管载Pt后的欧姆极化阻抗和电化学阻抗均非常小.     

Glassy carbon electrode modified with gold nanoparticles and DNA for the simultaneous determination of uric acid and norepinephrine under coexistence of ascorbic acid.

A novel biochemical sensor was assembled on a glass carbon electrode by a electrodeposition process. Gold nanoparticles were deposited by potential +1.5 V on the glass carbon electrode. CT-DNA was deposited by potential +1.5 V on the gold nanoparticles array electrode. The properties of the modified electrode were characterized by electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Our results showed that gold nanoparticles increase the DNA membrane capacitance and reduce the membrane resistance. This modified electrode can selectively determine uric acid and norepinephrine in the presence of a larger amount of ascorbic acid. The fabricated electrode showed good sensitivity, reproducibility, and stability.     

基于羧基化碳纳米管修饰电极伏安法同时测定痕量锢和铝

基于羧基化多壁碳纳米管(c-MWCNT),制备了可同时测定In3+和Al3+的新型碳材料修饰电极.利用循环伏安法(CV)和交流阻抗法(EIS)对此修饰电极进行了表征,用线性扫描伏安法(LSV)研究了In3+与Al3+共存于修饰电极上的电化学行为.与裸玻碳电极相比,新型碳材料修饰电极的电化学活性得到很大提高;In3+与A...     

Disposable electrochemical biosensor with multiwalled carbon nanotubes-chitosan composite layer for the detection of deep DNA damage.

A novel electrochemical DNA-based biosensor for the detection of deep DNA damage was designed employing the bionanocomposite layer of multiwalled carbon nanotubes (MWNT) in chitosan (CHIT) deposited on a screen printed carbon electrode (SPCE). The biocomponent represented by double-stranded (ds) herring sperm DNA was immobilized on this composite using layer-by-layer coverage to form a robust film. Individual and complex electrode modifiers are characterized by a differential pulse voltammetry (DPV) with the DNA redox marker [Co(phen)(3)](3+), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) with [Fe(CN)(6)](3-) as a redox probe in a phosphate buffer solution (PBS). A good correlation between the CV and EIS parameters has been found, thus confirming a strong effect of MWNT on the enhancement of the electroconductivity of the electrode surface and that of CHIT on the MWNT distribution at the electrode surface. Differences between the CV and EIS signals of the electrodes without and with DNA are used to detect deep damage to DNA, advantageously using simple working procedures in the same experiment.     

Carbon nanotubes as a secondary support of a catalyst layer in a gas diffusion electrode for metal air batteries

In this paper, we report the use of binary carbon supports (carbon nanotubes (CNTs) and active carbon) as a catalyst layer for fabricating gas diffusion electrodes. The electrocatalytic properties for the oxygen reduction reaction (ORR) were evaluated by polarization curves and electrochemical impedance spectroscopy (EIS) in an alkaline electrolyte. The binary-support electrode exhibits better performance than the single-support electrode, and the best performance is obtained when the mass ratio of carbon nanotubes and active carbon is 50:50. The results from the electrode kinetic parameters indicate that the introduction of carbon nanotubes as a secondary support provides high accessible surface area, good electronic conductivity, and fast ORR kinetics. Furthermore, the effect of CNT support on the electrocatalytic properties of Pt nanoparticles for binary-support electrodes was also investigated by different loading-reduction methods. The electrocatalytic activity of the binary-support electrodes is improved dramatically by Pt loading on CNT carbon support, even at very low Pt loading. Additionally, the EIS analysis results indicate that the process of ORR may be controlled by diffusion of oxygen in the electrode thin film for binary-support electrodes with or without Pt catalyst.     

Electrooxidation of Nitric Oxide at a Glass Carbon Electrode Modified with Functionalized Single-walled Carbon Nanotube

The electrocatalytic oxidation of nitric oxide(NO) at a glass carbon electrode(GC) modified with functionalized single-walled carbon nanotubes(SWCNTs) was investigated by cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS).It was found that the SWCNT modified electrode could speed greatly up the electron transfer rate compared with the bare GC electrode.After the SWCNT was treated with alkali or mixed acids,the reaction rate and activation energy of NO electrooxidation were changed to different extent.Chemical modification of the SWCNT surface is one of the most powerful methods to change the sensitivity of NO electrooxidation reaction.The modified electrode with SWCNT obtained by the firstly alkali treatment and then the mixed acids treatment was the best one for NO electrooxidation,the result of CV was also confirmed by that of EIS.The anodic processes of NO were recognized more clearly by exploring the reaction mechanism of NO electrooxidation at the SWCNT modified electrode.     

Electrocatalysis of the SiC Particle‐Modified Glassy Carbon Electrode for the Oxidation of Adrenaline

The electrocatalytic properties of the SiC particle‐modified glassy carbon electrode (MGC) for adrenaline oxidation were studied by cyclic voltammetry (CV), double‐potential step chronocoulometry (DPSCC), and electrochemical impedance spectroscopy (EIS) techniques in McIlvaine buffer solution. It was shown that the electrode modified with SiC particles markedly displayed an electrocatalytic effect on the process of the electrochemical reaction of adrenaline, i.e., the activity and the reversibility of the MGC electrode has been significantly improved. This was attributed to the adsorption effect of the electroactive adrenaline molecules on the MGC electrode surface.     

基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

DNA/聚(3,4-乙烯基二氧噻吩)修饰电极的制备及其用于亚硝酸根的电化学行为及测定研究

采用恒电流和电沉积两步法制备了脱氧核糖核酸-聚(3,4-乙烯基二氧噻吩)(DNA-PEDOT)复合膜修饰玻碳电极。用电化学阻抗法(EIS)和循环伏安法(CV)表征了不同修饰电极的修饰可行性和表面的电子传递能力。结果表明,DNA可以牢固地结合在PEDOT膜上,并能改善PEDOT膜的性质。研究了NO2-在DNA-PEDOT修饰电极上的电化学行为,提出了一种新的检测NO2-的电化学方法。在0.1 mol/L pH7.0的磷酸盐缓冲溶液(PBS)中,NO2-在DNA-PEDOT修饰电极上于0.88 V左右出现1个较好的氧化峰,考察了该氧化峰的性质及其影响因素。示差脉冲伏安法(DPV)的结果表明,NO2-的DPV氧化峰电流与其浓度在0.3~1.0、1.0~20、20~100μmol/L 3个范围内呈良好的线性关系,检出限(S/N=3)为60 nmol/L,并考察了可能存在的干扰物质对测定的影响。结果显示,该复合膜修饰电极对NO2-的检测具有良好的稳定性和选择性。将其用于实际样品的检测,结果满意。     

旋转玻碳电极上二茂铁的电化学阻抗行为及其与DNA的相互作用

应用旋转圆盘电极和电化学阻抗法研究了二茂铁在Tris-NaC l(pH=7.2)缓冲溶液中于旋转玻碳电极上的电化学阻抗行为及其与DNA的相互作用.结果表明,二茂铁于旋转电极的伏安曲线呈现明显的极限电流平阶,而其交流阻抗谱则出现两个电容弧.二茂铁与DNA的作用,若受扩散过程控制则其极限扩散电流随DNA浓度增大而减小,而在电化学控制过程中则表现为电化学反应电阻随DNA浓度增大而增大.根据旋转圆盘电极和电化学阻抗谱测试,表明由这两种方法数据拟合求得的二茂铁条件电位速率常数能够很好地相互吻合,但如存在DNA时,则其条件电位速率常数有一定程度的减小.     

纳米金修饰玻碳电极对鸟嘌呤的催化氧化

采用电化学沉积法制备了纳米金修饰玻碳电极,并用循环伏安法和电化学阻抗法进行了表征,以此建立了一种直接测定鸟嘌呤的电分析方法。在磷酸盐缓冲溶液(pH 6.0)中,研究了鸟嘌呤在纳米金修饰电极上的电化学行为,实验结果表明,纳米金修饰电极可以增强鸟嘌呤在电极表面的吸附,并加快鸟嘌呤在电极表面的电子传输,使其电化学信号明显增大,检测灵敏度大大提高,该修饰电极对鸟嘌呤表现出良好的电催化性能。在优化实验条件下对鸟嘌呤进行测定,方法的线性范围为8.0×10-7~6.0×10-5mol/L,检出限为1.0×10-8mol/L,在鸟嘌呤浓度为1.0×10-5mol/L时测得RSD(n=10)为2.5%。     

聚多巴胺/多壁碳纳米管/玻璃碳电极上多巴胺的电分析

基于多巴胺（DA）在多壁碳纳米管（MWCNTs）修饰玻璃碳（GC）电极上的电聚合,制得聚多巴胺(PDA)/MWCNTs/GC电极,并对该修饰电极进行了电化学阻抗谱 (EIS)和循环伏安法(CV)表征。 在该修饰电极上,DA呈现良好的电化学行为。在pH=7.4磷酸缓冲溶液中其氧化电流显著高于在裸电极上的响应,且能有效地抑制2.0 mmol/L抗坏血酸(AA)或K4Fe(CN)6的直接电化学响应,表明MWCNTs可增敏信号,且阳离子选择透过性PDA膜可抑制阴离子的电化学干扰。 采用CV实验检测DA,DA氧化的半微分伏安峰高(ipa-sd)与多巴胺浓度在0.08～1.76 μmol/L范围内呈线性关系,在无抗坏血酸和有0.5 mmol/L抗坏血酸共存时的线性回归方程分别为ipa-sd(μA/s1/2)=0.107+0.405c(μmol/L)（r2=0.986）和ipa-sd(μA/s1/2)=0.628+0.649c(μmol/L)(r2=0.992),检测限均为8.0×10-8 mol/L(S/N=3)。 该法用于盐酸多巴胺注射液中多巴胺的快速测定,结果满意。     

原位电化学还原制备石墨烯修饰玻碳电极及其对亚硝酸根离子的电催化氧化性能

通过原位电化学还原直接制备石墨烯修饰玻碳电极,并用电化学阻抗谱（EIS）和扫描电子显微镜（SEM）对其进行了表征,研究了亚硝酸根离子（NO2-）在石墨烯修饰玻碳电极上的电化学行为.结果表明：石墨烯修饰玻碳电极对NO2-的氧化反应有良好的电催化活性,NO2-的浓度与峰电流呈良好的线性关系,且在pH 7.0的磷酸盐缓冲液（PBS）中其氧化峰电流最高.利用该方法测定了模拟废水中NO2的含量,结果令人满意.     

血红蛋白在类生物膜修饰电极上的直接电化学

使用掺合单壁碳纳米管(SWCNT)的不溶性表面活性剂双十二烷基二甲基溴化铵(DDAB)修饰玻碳电极,并将血红蛋白(Hb)固定在修饰膜中制得了稳定的固载Hb的修饰电极.循环伏安和交流阻抗测试表明,固定在电极上的Hb是一个受吸附控制的可逆电子传递过程.该氧化还原过程的CV扫描峰电位与溶液pH值成良好的线性关系,斜率39 mV/pH,表明在发生Hb直接电子传递反应的同时伴随有质子参与反应.掺合SWCNT的类生物膜修饰电极较之不掺合SWCNT的修饰电极对氧气的还原具有更好的催化作用.并以SWCNT掺合量为1 mg.mL-1的DDAB修饰电极性能最佳.     

纳米碳管作为氧扩散电极催化层第二相碳载体的电极特性

A novel gas diffusion electrode using binary carbon supports (carbon nanotubes and active carbon) as the catalyst layer was prepared. The electrochemical properties for oxygen reduction reaction (ORR) in alkaline electrolyte were investigated by polarization curves and electrochemical impedance spectroscopy. The results show that the binary-support electrode exhibits higher electrocatalytic activity than the single-support electrode, and the best performance is obtained when the mass ratio of carbon nanotubes and activated carbon is 50 ∶50. The results from their electrode kinetic parameters indicate that the introduction of carbon nanotubes as a secondary support provides high accessible surface area, good electronic conductivity and fast ORR kinetics. The electrocatalytic activity of binary-support electrodes is obviously improved by the deposition of Pt nanoparticles on carbon nanotubes, even at very low Pt loading (45.7 μg/cm2). In addition, the EIS analysis results show that the process of ORR may be controlled by diffusion of oxygen in the thin film for binary-support electrodes with or without Pt catalyst.     

Immobilization of Glycosylated Enzymes on Carbon Electrodes,and its Application in Biosensors

A novel approach was used to immobilize glycosylated enzymes on a glassy carbon electrode (GCE) based on the interaction of boronic acid and carbohydrate moiety within the glycoproteins. 4-Aminomethylphenylboronic acid (4-AMBA) was covalently grafted on a glassy carbon electrode (GCE) by amine cation radical formation in the electrooxidation process of the amino-containing compound. The boronic acid group immobilized in this way could recognize glycoproteins such as glucose oxidase, horseradish peroxidase, dehydrogenase and others. X-ray photoelectron spectroscopy measurement proved the presence of a 4-AMBA monolayer on the GCE. The adsorptions of three kinds of enzymes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The activity of the immobilized horseradish peroxidase was also studied.