高压下TiN的结构转变、弹性和热力学性质的第一性原理计算

 利用基于密度泛函的第一性原理,计算了高压下TiN的结构转变、弹性和热力学性质。计算结果表明：在压力作用下,TiN经历了从NaCl型结构到CsCl型结构的转变,转变压力为348 GPa;TiN的弹性系数随着压力的增加呈线性增加规律。此外,还给出了德拜温度和热容量这两个重要热力学量与温度和（或）压力的依赖关系。     

高压下钨弹性和热力学性质的第一性原理研究

本文利用密度泛函理论研究了高压下bcc结构钨的弹性和热力学性质,计算得到钨的晶格常数、体弹模量以及其对压强的一阶偏导与实验值符合较好;在常压下弹性常数计算值与实验值符合较好的基础上,预测了其高压数据.针对钨的固相结构稳定性问题,根据力学稳定判断标准得到0~600 GPa范围内bcc结构是力学稳定的.此外,通过体模量和剪切模量的计算得到bcc结构钨在压力低于600 GPa时的力学性能表现为韧性.最后,基于准简谐德拜模型,成功预测了钨的热膨胀系数、等压热容、等容热容和熵随着压强和温度的变化关系,为钨及其合金的进一步设计及应用提供参考.     

高压下钨弹性和热力学性质的第一性原理研究

本文利用密度泛函理论研究了高压下bcc结构钨的弹性和热力学性质,计算得到钨的晶格常数、体弹模量以及其对压强的一阶偏导与实验值符合较好;在常压下弹性常数计算值与实验值符合较好的基础上,预测了其高压数据.针对钨的固相结构稳定性问题,根据力学稳定判断标准得到0~600 GPa范围内bcc结构是力学稳定的.此外,通过体模量和剪切模量的计算得到bcc结构钨在压力低于600 GPa时的力学性能表现为韧性.最后,基于准简谐德拜模型,成功预测了钨的热膨胀系数、等压热容、等容热容和熵随着压强和温度的变化关系,为钨及其合金的进一步设计及应用提供参考.     

高压下CaPo弹性性质和热力学性质的第一性原理研究

利用密度泛函理论的平面波赝势方法预测研究了CaPo从岩盐结构(B1结构)到氯化铯结构(B2结构)的相变以及B1结构CaPo高压下的弹性性质以及热力学性质等.通过等焓原理发现B1→B2的相变压力为22.8GPa. 同时计算了B1结构CaPo高压下的弹性常数以及剪切模量、杨氏模量等相关弹性参数,结果发现当压力超过20GPa时,B1结构CaPo开始不稳定了,这和等焓原理所得结果相符合. 最后通过Debye模型成功获取了B1结构C 关键词： 相变 弹性性质 热力学性质 CaPo     

高压下硫化钙的弹性和热力学性质的第一性原理计算

利用基于密度泛函理论的第一性原理平面波赝势方法结合准谐德拜模型研究NaCl结构的CaS在高压下的弹性和热力学性质.计算得到的零温零压下的晶格常数、体弹模量与实验值符合得很好.弹性常数和弹性模量随着压强的增大而增大.压强对体弹模量和热膨胀系数的影响大于温度的影响.热容随压强的升高而降低,在高温下热容接近于Dulong-Petit极限.通过求解Gibbs自由能计算得到B1结构和B2结构CaS的相变压为36.61 GPa.     

ZrRh晶体结构、弹性性质和电子结构的第一性原理研究

运用基于密度泛函理论的第一性原理计算方法研究了ZrRh的晶体结构、弹性性质和电子结构性质.结果表明:计算的B2、B19'和ZrIr结构的平衡晶格常数与相应的实验参数符合很好.从形成焓和态密度的角度来看,ZrRh的相稳定顺序是ZrIrFe BB19'B2,ZrIr结构是最稳定的.ZrIr结构的形成焓最小,说明ZrIr结构最容易生成.利用应力-应变的方法计算了ZrRh的弹性常数,表明B2、FeB和ZrIr结构是力学稳定的.B/G和泊松比均表明ZrRh具有很好的延展性.对ZrRh的态密度研究发现,增强的Rh4d态与Zr4d态杂化作用是ZrIr结构稳定的主要原因.     

ZrV2结构、弹性和热力学性质的第一性原理计算

采用基于密度泛函理论的第一性原理平面波赝势方法研究ZrV₂的晶体结构和弹性,利用准谐Debye模型计算在不同温度(T=0~1200 K)和不同压强(P=0~20 GPa)下ZrV₂的热力学性质,包括弹性模量与压强,热熔与温度,以及热膨胀系数与温度和压力的关系.结果表明:计算的ZrV₂晶格常数与实验值符合较好,晶体材料的弹性常数随着压力增加而增加;在一定温度下,相对体积、热熔随着压强的增加而减小,德拜温度、弹性模量随着压强的增加而增加,且高压下温度对ZrV₂热膨胀系数的影响小于压强的影响.     

Mg2Sn电子结构及热力学性质的第一性原理计算

采用基于第一性原理的赝势平面波方法系统地计算了Mg2Sn基态的电子结构、弹性常数和热力学性质.计算结果表明Mg2Sn的禁带宽度为0.1198eV.运用线性响应方法确定了声子色散关系和态密度,得出Mg2Sn的热力学性质如等容比热和德拜温度.计算Mg2Sn的热导率并与实验数据相比较.     

高压下ErNi2B2C弹性性质、电子结构和热力学性质的第一性原理研究

采用密度泛函理论中的赝势平面波方法研究了高压下超导材料 ErNi₂B₂C 的弹性性质、电子结构和热力学性质.分析表明, 弹性常数、体弹模量、剪切模量、杨氏模量和弹性各向异性因子的外压力效应明显. 电子态密度(DOS)的计算结果显示, 在费米能级(E_F)处的 DOS 峰随外界压强的增大显著降低, 由于 ErNi₂B₂C 相对较高的超导温度(T_c)起因于E_F处的 DOS 峰, 因此推测压强增大可能会降低 ErNi₂B₂C 的 T_c.类似的现象在超导材料 MgB₂和 SrAlSi 中已被发现.此外, 基于准谐德拜模型, 对 ErNi₂B₂C 在高温高压下的热力学性质的研究表明, 在一定范围内, 温度和压强将对其热膨胀系数和热容产生明显的影响. 关键词： 高压 弹性性质 电子结构 热力学性质     

MnPd合金相变，弹性和热力学性质的第一性原理研究

运用基于密度泛函理论第一性原理方法研究了MnPd从立方顺磁到四方反铁磁的相变以及其弹性性质和热力学性质等．结果表明：MnPd合金顺磁立方B2结构在施加了四方应变后，结构不稳定，会发生结构相变形成四方顺磁结构．四方顺磁相弹性稳定，然而在考虑了磁性后，反铁磁四方相比四方顺磁相能量更低，而且弹性和动力学都稳定，说明反铁磁四方相是MnPd的低温结构．从而得出MnPd合金的相变路径为两步：先发生结构相变从顺磁B2立方结构转变为顺磁四方相，再由磁性诱发相变形成反铁磁四方结构．通过准谐近似得到了摩尔比热容，德拜温度等热力学性质．     

First-principles calculations of elastic,phonon and thermodynamic properties of W

We investigate the elastic properties, lattice dynamical, thermal equation of state and thermodynamic properties of bcc phase W under high pressure using density functional theory. The calculated high-pressure elastic constants of bcc phase W agree well with experimental and theoretical data. Under compression, the phonon dispersion curves of bcc phase W do not show any anomaly or instability. Our calculated zero-pressure phonon dispersion curves are in excellent agreement with experiments. Within the quasiharmonic approximation, we predict the thermal equation of state and other properties including the thermal expansion coefficient, adiabatic bulk modulus, specific heat at constant volume and entropy.     

Thermodynamic properties of cubic ZrC under high pressure from first-principles calculations

The elastic and thermodynamic properties of Zirconium carbide (ZrC) are investigated by ab initio plane-wave pseudopotential density function theory method. The obtained lattice constant, elastic constant and bulk modulus B are consistent with the experimental and theoretical data. Through the quasi-harmonic Debye model, the dependences of the normalized volume V/V ₀ and the bulk modulus B on pressure P, as well as the specific heat C _V on the temperature T are obtained successfully. The relationships of the thermal expansion α with temperature and pressure are also investigated, which indicate the temperature hardly has any effect on the thermal expansion α at high pressure. Supported by the National Natural Science Foundation of China (Grant No. 10776022)     

Structural,elastic, thermodynamic and electronic properties of LuX (X = N,Bi and Sb) compounds: first principles calculations

ABSTRACT

The structural, electronic, elastic and thermodynamic properties of LuX (X = N, Bi and Sb) based on rare earth into phases, Rocksalt (B1) and CsCl (B2) have been investigated using full-potential linearized muffin-tin orbital method (FP-LMTO) within density functional theory. Local density approximation (LDA) for exchange-correlation potential and local spin density approximation (LSDA) are employed. The structural parameters as lattice parameters a₀, bulk modulus B, its pressure derivate B’ and cut-off energy (E_c) within LDA and LSDA are presented. The elastic constants were derived from the stress–strain relation at 0 K. The thermodynamic properties for LuX using the quasi-harmonic Debye model are studied. The temperature and pressure variation of volume, bulk modulus, thermal expansion coefficient, heat capacities, Debye temperature and Gibbs free energy at different pressures (0–50 GPa) and temperatures (0–1600 K) are predicted. The calculated results are in accordance with other data.     

密度泛函理论研究高温高压下UO2弹性与热力学性能

采用第一性原理与准谐德拜模型研究UO2在高温高压条件下的弹性与热力学性能。UO2在高温高压下仍属离子型晶体,并且弹性性能计算表明,四角方向剪切常数在高温与高压下均保持稳定。高温下弹性常数C44没有明显变化,而高压下C44迅速增大。体积模量、剪切模量与杨氏模量均随压强增加而增大;高温条件下,体积模量、剪切模量与杨氏模量也未出现明显的降低,表明UO2在高温度高压下均可保持良好的力学性能。不同压强下,UO2定容热容均随温度迅速增大,并在1000 K 附近趋近于杜隆-佩蒂特极限。德拜温度则随温度降低,随压强升高。在低于室温条件下,热膨胀系数随温度急剧增加;温度继续增加,系数的增加趋势则逐渐变缓。计算结果还表明,UO2的热膨胀系数在相同条件下,远小于其他核材料。     

Structural,elastic, electronic,and thermodynamic properties of MgAgSb investigated by density functional theory

The structural, elastic, electronic, and thermodynamic properties of thermoelectric material Mg Ag Sb in γ, β, α phases are studied with first-principles calculations based on density functional theory. The optimized lattice constants accord well with the experimental data. According to the calculated total energy of the three phases, the phase transition order is determined from α to γ phase with cooling, which is in agreement with the experimental result. The physical properties such as elastic constants, bulk modulus, shear modulus, Young's modulus, Poisson's ratio, and anisotropy factor are also discussed and analyzed, which indicates that the three structures are mechanically stable and each has a ductile feature. The Debye temperature is deduced from the elastic properties. The total density of states(TDOS) and partial density of states(PDOS) of the three phases are investigated. The TDOS results show that the γ phase is most stable with a pseudogap near the Fermi level, and the PDOS analysis indicates that the conduction band of the three phases is composed mostly of Mg-3s,Ag-4d, and Sb-5p. In addition, the changes of the free energy, entropy, specific heat, thermal expansion of γ-MgAgSb with temperature are obtained successfully. The obtained results above are important parameters for further experimental and theoretical tuning of doped MgAgSb as a thermoelectric material at high temperature.