反应溅射法制备TiO2薄膜

报道了用反应溅射法制备TiO₂薄膜的实验研究.详细研究了氧分压、基底温度和退火温度对成膜结构的影响.制备出了具有金红石和锐钛矿晶体结构的TiO₂薄膜.分析了金红石和锐钛矿晶体的形成条件,并对薄膜的表面形貌进行了测量. 关键词： 反应溅射 2薄膜')" href="#">TiO₂薄膜     

化学法制备的HfO2薄膜的激光损伤阈值研究

 采用化学法制备了HfO₂介质膜，研究了热处理、紫外辐照以及Al₂O₃复合对HfO₂介质膜激光损伤阈值的影响。采用红外光谱（FTIR）和X射线衍射仪对薄膜进行了表征，并用输出波长为1.064 μm、脉宽为10 ns的电光调Q激光系统测试薄膜的激光损伤阈值。实验结果表明：采用150 ℃左右的温度对薄膜进行热处理可以提高薄膜的激光损伤阈值，所获得的薄膜的激光损伤阈值高达42.32 J/cm²，比热处理前的激光损伤阈值提高了82%；无机材料Al₂O₃的适量添加能够提高薄膜的激光损伤阈值，其中HfO₂与Al₂O₃的最佳质量配比约为95∶5；另外，对薄膜进行适当的紫外辐照也可改善HfO₂ 薄膜以及HfO₂-Al₂O₃复合薄膜的抗激光损伤性能。紫外辐照对提高HfO₂-Al₂O₃复合薄膜的激光损伤阈值效果尤为显著，辐照40 min后的激光损伤阈值达到44.33 J/cm²，比紫外辐照前的激光损伤阈值提高了90%。     

n型透明导电薄膜CdIn2O4电学性质的研究和大面积制备的最佳条件

在Ar+O2₂气氛中，采用射频反应溅射Cd-In靶制备CdIn2₂O4₄ 薄膜.制得的薄膜经x射线衍射（XRD）检测为CdIn2₂O4₄和CdO相组成的多晶.从理论上分析了热 处理前后氧空位、掺杂点缺陷和富氧电子陷阱在影响膜的载流子浓度和电子散射中所起的重要作用.同时，对样品 进行Hall效应、Seebeck效应测试并得出不同载流子浓度下的迁移率、有效质量、弛豫时间以及它们之间的相互关系，特别强调     

第2系列ZrO2(Y2O3)薄膜的慢正电子研究

用慢正电子技术研究了在溅射时不加偏压,衬底加热300℃,纯Ar气氛下制备的用Y_{2O3稳定的ZrO2薄膜材料(简称YSZ薄膜),发现了YSZ薄膜在不同 深度处的缺陷分布情况,退火温度对YSZ薄膜缺陷有影响.简要讨论了致密、优质YSZ薄膜的 制备方法.}     

溶胶-凝胶法制备高折射率TiO2薄膜

 采用溶胶- 凝胶法制备了TiO₂纳米晶溶胶,并以旋涂法（spin-coating）镀制了高折射率光学薄膜。借助光散射技术和透射电镜研究了溶胶的微结构。采用原子力显微镜、场发射扫描电镜、紫外-可见-近红外光谱仪、椭偏仪、漫反射吸收光谱及强激光辐照实验,对膜层的结构、光学性能及抗激光损伤性能进行了系统的表征。结果显示:纳米晶薄膜的折射率达到了1.9,而传统的溶胶-凝胶薄膜折射率只有1.6;同时纳米晶薄膜的抗激光损伤阈值与传统的溶胶-凝胶薄膜相差不大,在1 064 nm处分别为16.3 J/cm²(3 ns脉冲) 和16.6 J/cm²(3 ns脉冲);纳米晶溶胶薄膜可以在保持较高抗激光损伤阈值情况下,大幅度提高薄膜折射率。     

不同氧气流量对直流磁控溅射TiO2薄膜的影响

采用直流反应磁控溅射法,以高纯Ti为靶材,高纯O₂为反应气体,制备了TiO₂薄膜.研究了氧气流量对薄膜结晶取向、表面形貌和光学性能的影响.研究发现,TiO₂薄膜主要呈锐钛矿TiO₂(101)择优取向,当氧气流量较小时,薄膜中还含有金属Ti(100),氧气流量较大时,薄膜含TiO₂(101)和TiO₂(004),成多晶态;薄膜的粗糙度和颗粒大小都随氧气流量的增大而增大;薄膜在400~1100nm可见-近红外波段有较高的透射率并且其吸收峰随着氧气流量的增大而红移,当氧气流量为5sccm时,平均透射率最高.     

射频磁控溅射法制备SnO2:Sb薄膜的结构和光致发光性质研究

采用射频磁控溅射法在玻璃衬底上制备出锑掺杂的氧化锡（SnO2₂:Sb）薄膜.制 备薄膜是具有纯氧化锡四方金红石结构的多晶膜薄，晶粒生长的择优取向为［110］.室温下光致发光测量结果表明，在392nm附近存在强的紫外-紫光发射.研究了不同氧分压对薄膜结构及发光性质的影响，并对SnO2₂:Sb的光致发光机制进行了探索性研究.     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

电子束蒸发法制备ZrO2薄膜的相变模型分析

 用电子束蒸发方法制备了纯的ZrO₂薄膜和含Y₂O₃摩尔分数为7%和13%的ZrO₂薄膜,即YSZ薄膜,通过测定薄膜的损伤阈值来验证温度诱导相变模型;并用X射线衍射（XRD）来测定ZrO₂和YSZ镀膜材料和薄膜的结构特征。结果表明：ZrO₂镀膜材料和薄膜室温下都表现为单斜相,YSZ镀膜材料和薄膜室温下都以立方相存在;YSZ薄膜的损伤阈值远高于ZrO₂薄膜的损伤阈值,这是因为添加Y₂O₃后的YSZ材料的相比较稳定,在蒸发过程中不会发生相变,而ZrO₂材料则发生相变,产生缺陷,缺陷在激光作用下成为吸收中心和初始破坏点,导致ZrO₂薄膜的损伤阈值降低。     

Optical properties of p-type CuAlO2 thin film grown by rf magnetron sputtering

We report the structural and optical properties of copper aluminium oxide (CuAlO₂) thin films, which were prepared on c-plane sapphire substrates by the radio frequency magnetron sputtering method. X-ray photoelectron spectroscopy (XPS) along with X-ray diffraction (XRD) analysis confirms that the films consist of delafossite CuAlO₂ phase only. The optical absorption studies show the indirect and direct bandgap is 1.8 eV and 3.45 eV, respectively. Room temperature photoluminescence (PL) measurements show three emission peaks at 360 nm (3.45 eV), 470 nm (2.63 eV) and 590 nm (2.1 eV). The first one is near band edge emission while the other two are originated from defects.     

磁控溅射法合成纳米β-FeSi2/a-Si多层结构

β-FeSi₂作为一种环境友好的半导体材料，颗粒化及非晶化正在成为提高其应用性能和改善薄膜质量、膜基界面失配度的有效途径.利用射频磁控溅射法在单晶Si基体上沉积Fe/Si多层膜，合成纳米β-FeSi₂/Si多层结构.通过透射电子显微镜、高分辨电子显微术等分析手段，研究了多层结构和制备工艺之间的相互关系.研究结果表明，采用磁控溅射Fe/Si多层膜的方法，不需要退火就可以直接沉积得到β-FeSi₂相小颗粒.β-FeSi₂相 关键词： 2')" href="#">β-FeSi₂ 磁控溅射 透射电子显微镜 半导体薄膜     

使用硫化物纳米前驱物墨水法制备铜铟硫薄膜

提出了一种通过反应烧结来制备CuInS₂多晶薄膜的低成本旋涂工艺路线．通过将前驱物粉末在氢气中预还原的方法来优化旋涂时使用的墨水成分,氢气还原会使前驱物纳米粉末从硫化物混合粉末转变成CuInS₂和Cu-In合金的混合物．扫描电子显微镜、电子能谱、X射线衍射以及拉曼图谱的结果表明,这种优化能极大的提高CuInS₂多晶薄膜的性能,其中包括薄膜的排列密度更高,杂质相减少,薄膜质量变得更好等．吸收光谱测得优化后的铜铟硫薄膜的带隙约为1.45 eV．     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

The structure and photocatalytic activity of TiO2 thin films deposited by dc magnetron sputtering

This paper seeks to determine the optimal settings for the deposition parameters, for TiO₂ thin film, prepared on non-alkali glass substrates, by direct current (dc) sputtering, using a ceramic TiO₂ target in an argon gas environment. An orthogonal array, the signal-to-noise ratio and analysis of variance are used to analyze the effect of the deposition parameters. Using the Taguchi method for design of a robust experiment, the interactions between factors are also investigated. The main deposition parameters, such as dc power (W), sputtering pressure (Pa), substrate temperature (°C) and deposition time (min), were optimized, with reference to the structure and photocatalytic characteristics of TiO₂. The results of this study show that substrate temperature and deposition time have the most significant effect on photocatalytic performance. For the optimal combination of deposition parameters, the (1 1 0) and (2 0 0) peaks of the rutile structure and the (2 0 0) peak of the anatase structure were observed, at 2θ ∼ 27.4°, 39.2° and 48°, respectively. The experimental results illustrate that the Taguchi method allowed a suitable solution to the problem, with the minimum number of trials, compared to a full factorial design. The adhesion of the coatings was also measured and evaluated, via a scratch test. Superior wear behavior was observed, for the TiO₂ film, because of the increased strength of the interface of micro-blasted tools.     

Effects of O2/Ar ratio and annealing temperature on electrical properties of Ta2O5 film prepared by magnetron sputtering

The effects of the oxygen-argon ratio on electric properties of Ta2O5 film prepared by radio-frequency magnetron sputtering were investigated.The Ta2O5 partially transforms from the amorphous phase into the crystal phase when annealing temperatures are 800℃ or higher.The lattice constant of Ta2O5 decreases with the increase of the O2/Ar ratio,which indicates that oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies during the deposition process.For the films deposited in working gas mixtures with different O2/Ar ratios and subsequently annealed at 700℃,the effective dielectric constant is increased from 14.7 to 18.4 with the increase of the O2/Ar ratio from 0 to 1.Considering the presence of an SiO2 layer between the film and the silicon substrate,the optimal dielectric constant of Ta2O5 film was estimated to be 31.Oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies,and the oxygen vacancy density and leakage current of Ta2O5 film both decrease with the increase of the O2/Ar ratio.The leakage current decreases after annealing treatment and it is minimized at 700℃.However,when the annealing temperature is 800℃ or higher,it increases slightly,which results from the partially crystallized Ta2O5 layer containing defects such as grain boundaries and vacancies.     

Effect of [Cu]/[In] ratio on properties of CuInS2 thin films prepared by successive ionic layer absorption and reaction method

CuInS₂ ternary films were prepared by a soft solution processing, i.e. successive ionic layer absorption and reaction (SILAR) method. The films were deposited on glass substrates at room temperature and heat-treated under Ar atmosphere at 500 °C for 1 h. CuCl₂ and InCl₃ mixed solutions with different ionic ratios ([Cu]/[In]) were used as cation precursor and Na₂S as the anion precursor. The effect of the [Cu]/[In] ratio in precursor solution on the structural, chemical stoichiometry, topographical, optical and electrical properties of CuInS₂ thin films was investigated. XPS results demonstrated that stoichiometric CuInS₂ film can be obtained by adjusting [Cu]/[In] ratios in solution. Chalcopyrite structure of the film was confirmed by XRD analysis. The near stoichiometric CuInS₂ film has the optical band gap E_g of 1.45 and resistivity decreased with increase of [Cu]/[In] ratios.     

射频磁控反应溅射制备的Ag2O薄膜的椭圆偏振光谱研究

Ag₂O薄膜在新型超高存储密度光盘和磁光盘方面具有潜在的应用前景.利用射频磁控反应溅射技术, 通过调节衬底温度在沉积气压为0.2 Pa、氧氩比为2:3的条件下制备了一系列Ag₂O 薄膜.利用通用振子模型(包括1个Tauc-Lorentz振子和2个Lorentz 振子)拟合了薄膜的椭圆偏振光谱.在1.5-3.5 eV能量区间,薄膜的折射率在2.2-2.7之间, 消光系数在0.3-0.9之间. 在3.5-4.5 eV能量区间,薄膜呈现了明显的反常色散,揭示Ag₂O薄膜的等离子体振荡频率在 3.5-4.5 eV之间. 随着衬底温度的升高,薄膜的光学吸收边总体上发生了红移, 该红移归结于薄膜晶格微观应变随衬底温度的升高而增大. Ag₂O薄膜的光学常数表现出典型的介质材料特性.     

Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.     

蓝宝石衬底上Gd2O3掺杂CeO2氧离子导体电解质薄膜的生长及电学性能

采用反应磁控溅射方法,在(0001)蓝宝石单晶衬底上,制备了纳米多晶Gd₂O₃掺杂CeO₂(GDC)氧离子导体电解质薄膜,采用X射线衍射仪(XRD)、原子力显微镜(AFM)对薄膜物相、结构、粗糙度、表面形貌等生长特性进行了表征,利用交流阻抗谱仪测试了GDC薄膜不同温度下的电学性能;实验结果表明,GDC薄膜为面心立方结构,在所研究的衬底温度范围内,均呈强(111)织构生长;薄膜表面形貌随衬底温度发生阶段性变化：衬底温度由室温升高到300℃时, 关键词： 2O₃掺杂CeO₂电解质薄膜')" href="#">Gd₂O₃掺杂CeO₂电解质薄膜 反应磁控溅射 生长特性 电学性能