Selective extraction of iron(III) from aqueous nitrate solution in the presence of cobalt(II), copper(II) and nickel(II) ions using bis(delta2-2-imidazolinyl)-5,5'-dioxime.

The feasibility of using bis(delta2-2-imidazolinyl)-5,5'-dioxime (H2L) for the selective extraction of iron(III) from aqueous solutions was investigated by employing an solvent-extraction technique. The extraction of iron(III) from an aqueous nitrate solution in the presence of metal ions, such as cobalt(II), copper(II) and nickel(II), was carried out using H2L in binary and multicomponent mixtures. Iron(III) extraction has been studied as a function of the pH, equilibrium time and extractant concentration. From the extracted complex species in the organic phase, iron(III) was stripped with 2 M HNO3, and later determined using atomic-absorption spectrometry. The extraction was found to significantly depend on the aqueous solution pH. The extraction of iron(III) with H2L increases with the pH value, reaching a maximum in the zone of pH 2.0, remaining constant between 2 and 3.5 and subsequently decreasing. The quantitative extraction of iron(III) with 5 x 10(-30 M H2L in toluene is observed at pH 2.0. H2L was found to react with iron(III) to form ligand complex having a composition of 1:2 (Fe:H2L).     

Sequential potentiometric complexometric redox determination of iron(III) and cobalt(II) with application to alloys

A simple potentiometric method is presented for successive determination of iron(III) and cobalt(II) by complexometric titration of the iron(III) with EDTA at pH 2 and 40 degrees , followed by redox titration of the cobalt(II) complex with 1,10-phenanthroline or 2,2'-bipyridyl at pH 4-5 and 40 degrees , with gold(III). There is no interference in either determination from common metal ions other than copper(II), which severely affects the cobalt determination but can be removed by electrolysis. The method has been successfully applied to determination of iron and cobalt in Kovar and Alnico magnet alloys.     

Spectrophotometry Determination of Iron(III) and Cobalt(II) with Salicylaldehyde Hydrazone (SH)

Iron and cobalt complexation with salicylaldehyde hydrazone (SH) has been studied spectrophotometrically employing solvent extraction technique. The Fe(III)-SH (1:3) and Co-SH (1:2) complex absorb at 510nm and 450 nm respectively. The sensitivity of the colour reactions are 0.014 and 0.005 in terms of Sandell's definition for iron and cobalt systems. Both the complexes show maximum and constant absorbance in the pH ranges 3.5 to 5.0 and 6.2 to 7.0 for Fe(III)-SH and Co(II)-SH respectively. The complexation has been used in the spectrophotometric determination of iron and cobalt in coexistence with several ions.     

Spectrophotometric studies on ion-pair extraction equilibria of the iron(ii) and iron(III) complexes with 4-(2-pyridylazo)resorcinol

The ion-pair extraction equilibria of the iron(II) and iron(III) chelates of 4-(2-pyridylazo)resorcinol (PAR, H(2)L) are described. The anionic chelates were extracted into chloroform with benzyldimethyltetradecylammonium chloride (QC1) as counter-ion. The extraction constants were estimated to be K(ex1)(Fe(II)) = [Q{Fe(II)(HL)L}](0)/[Q(+)][{Fe(II)(HL)L}(-)] = 10(8.59 +/- 0.11), K(ex2)(Fe(II)) = [Q(2){Fe(II)L(2)}](o)/ [Q(+)](2)[{Fe(II)L(2)}(2-)] = 10(12.17 +/- 0.10) and K(ex1)(Fe(III)) = [Q{Fe((III))L(2)}](o)/(Q(+)][{Fe(III)L(2)}(-)] = 10(6.78 +/- 0.15) at I = 0.10 and 20 degrees , where [ ](o) is concentration in the chloroform phase. Aggregation of Q{Fe(III)L(2)} in chloroform was observed and the dimerization constant (K(d) = [Q(2){Fe(III)L(2)}(2)](o)/[Q{Fe(III)L(2)}](o)(2)) was evaluated as log K(d) = 4.3 +/- 0.3 at 20 degrees . The neutral chelates of {Fe(II)(HL)(2)} and {Fe(III)(HL)L}, and the ion-pair of the cationic chelate, {Fe(III)(HL)(2)}ClO(4), were also extracted into chloroform or nitrobenzene. The relationship between the forms and extraction properties of the iron(II) and iron(III) PAR chelates are discussed in connection with those of the nickel(II) and cobalt(III) complexes. Correlation between the extraction equilibrium data and the elution behaviour of some PAR chelates in ion-pair reversed-phase partition chromatography is also discussed.     

Iron(II), cobalt(III), nickel(II) and copper(II) chelates of furan and thiophene azo-oximes

Summary Complexes of furan and thiophene azo-oximes with iron(II), cobalt(III), nickel(II) and copper(II) have been prepared and characterised. Iron(II), cobalt(III) and copper(II) complexes are diamagnetic in the solid state. The diamagnetism of the copper(II) chelates is suggestive of antiferromagnetic interaction between two copper centres.¹H n.m.r. spectral data suggest atrans-octahedral geometry for the tris-chelates of cobalt(III). Nickel(II) complexes are paramagnetic, in contrast to the diamagnetism of the analogous complexes of arylazooximes. The electronic spectra are suggestive of octahedral geometry for the iron(II), cobalt(III) and nickel(II) complexes, andD _4h -symmetry for copper(II). Infrared data indicate N-bonding of the oximino-group to the metal ions.     

Spectrophotometric estimation of cobalt(II) with nitrilotriacetic acid

A convenient and efficient method for the estimation of cobalt(II) ions in the presence of other metal ions is described. Interference of metal ions such as iron(II), iron(III), nickel(II), manganese(II), and copper(II) have been investigated. Only iron(III) ions seriously affect this determination. Copper(II) and nickel(II) ions do not interfere if present in a molar-ratio less than 1:2 in the cobalt(II) ion solution. Cobalt(II)-nickel(II) and cobalt(II)-copper(II) binary mixtures can be efficiently analyzed at selective wavelengths.     

Racemic iron(III) and cobalt(III) complexes containing a new pentadentate "helmet" phthalocyaninato ligand

Solvothermal reactions of iron(II) acetate tetrahydrate and cobalt(II) acetate tetrahydrate with 1,2-dicyanobenzene in methanol solution result in the formation of racemic six-coordinate iron(III) and cobalt(III) complexes, respectively, with a new bicyclic pentadentate 14,28-[1,3-diiminoisoindolinato]phthalocyaninato ligand.     

Dosage electrochimique du cobalt: I. Etude des Courbes Intensité— Potentiel du Système cobalt(III)/cobalt(II) en Milieu Picolique

Electrochemical determination of cobalt. Part I. Studies of current—voltage curves of the cobalt(III)/cobalt(II) system in picolinic acid mediaAs a preliminary to the development of electrochemical determinations of cobalt in steels, current—voltage curves at a platinum electrode were studied for the systems coblt(III)/cobalt(II) and iron(III)/iron(II) in media containing picolinic acid as complexing agent. Iron(III) oxidizes cobalt(II) in this complexmg medium, and the iron-(II) formed can be determined by an oxidant such as cerium(IV).     

Thin-layer chromatography of tris(1,10-phenanthroline)iron(II) and tris(2,2′-bipyridine)iron(II) on Sephadex G gels

Summary Gel chromatographic behaviour of tris(1, 10-phenanthroline)iron(II), tris(2,2′-bipyridine)iron(II) and tris(glycinato)cobalt(III) on Sephadex G-10 or G-25 was investigated by TLC with 0.001–1.0M NaCl as the eluent. The zone shapes and R_M values of tris(1,10-phenanthroline)iron(II) and tris(2,2′-bipyridine)iron(II) were appreciably dependent on the sample and eluent concentration, while the neutral complex, tris(glycinato) cobalt(III), exhibited the round zones with constant R_M values. The order of R_M values was found to be tris(glycinato)cobalt(III<tris(2,2∔pyridine)iron(II)<tris-(1,10-phenanthroline)iron(II) in all systems studied, although the reverse trend was expected when assuming the chromatographic behaviour of solute compounds to be controlled by the “sieving effect”. The comparison of the behaviour on Sephadex G gels with that on CM-cellulose revealed that the predominant mechanism involved is not the sieving effect, but ion-exchange and/or hydrophobic interaction.     

High performance liquid chromatographic separation and UV determination of cobalt, copper iron and platinum in pharmaceutical preparations using bis(isovalerylacetone)ethylenediimine as complexing reagent

The reagent bis(isovalerylacetone)ethylenediimine(H₂IVA₂en) has been examined for HPLC separation and UV determination of cobalt, copper, iron and platinum using off-line precolumn derivatization and extraction in chloroform. The complexes of cobalt(II), cobalt(III), iron(II), iron(III) and the reagent have been subsequently separated on a Microsorb C-18 column. The complexes were eluted isocratically using ternary mixtures of methanol/water/acetonitrile. Detection was achieved by UV monitoring. Detection limits for Co(II), Co(III), Fe(II) and Fe(III) were 2.5–5.0 ng/injection, based on 0.5–1.0 g/ml with 5 l/injection. The concentration of cobalt(II) and cobalt(III) in aqueous solution have been determined. The presence of oxovanadium(IV), platinum(II), and nickel(II) did not affect the determinations. The HPLC method developed has been applied to the determination of cobalt, copper, iron and platinum in pharmaceutical preparations at the 30 g/g to 15 mg/g level and the obtained results were compared to those of atomic absorption spectrometry.     

Extraction and complexing of copper(II) with benzoic acid N,N-dihexylhydrazide

The solubility and acid-base properties of benzoic acid N,N-dihexylhydrazide (BDHH) were studied. The extraction of copper(II), cobalt(II), nickel(II), zinc(II), iron(III), platinum(II), platinum(IV), chromium(III), chromium(VI), palladium(II), and molybdenum(VI) with this reagent was studied. It was shown that BDHH most efficiently extracts copper(II) from ammonia solutions and chromium(VI) from sulfuric acid solutions. In the extraction of copper(II), complexes with the [Cu(II)]: [BDHH] = 1: 1 and 1: 2 stoichiometries were found to form. The structure of the 1: 2 complex was suggested proceeding from its IR spectra. A copper(II) extraction isotherm was plotted.     

Polymer Supported Schiff Base Complexes of Iron(III), Cobalt(II) and Nickel(II) Ions and their Catalytic Activity in Oxidation of Phenol and Cyclohexene

The polymer supported transition metal complexes of N,N′‐bis (o‐hydroxy acetophenone) hydrazine (HPHZ) Schiff base were prepared by immobilization of N,N′‐bis(4‐amino‐o‐hydroxyacetophenone)hydrazine (AHPHZ) Schiff base on chloromethylated polystyrene beads of a constant degree of crosslinking and then loading iron(III), cobalt(II) and nickel(II) ions in methanol. The complexation of polymer anchored HPHZ Schiff base with iron(III), cobalt(II) and nickel(II) ions was 83.30%, 84.20% and 87.80%, respectively, whereas with unsupported HPHZ Schiff base, the complexation of these metal ions was 80.3%, 79.90% and 85.63%. The unsupported and polymer supported metal complexes were characterized for their structures using I.R, UV and elemental analysis. The iron(III) complexes of HPHZ Schiff base were octahedral in geometry, whereas cobalt(II) and nickel(II) complexes showed square planar structures as supported by UV and magnetic measurements. The thermogravimetric analysis (TGA) of HPHZ Schiff base and its metal complexes was used to analyze the variation in thermal stability of HPHZ Schiff base on complexation with metal ions. The HPHZ Schiff base showed a weight loss of 58% at 500°C, but its iron(III), cobalt(II) and nickel(II) ions complexes have shown a weight loss of 30%, 52% and 45% at same temperature. The catalytic activity of metal complexes was tested by studying the oxidation of phenol and epoxidation of cyclohexene in presence of hydrogen peroxide as an oxidant. The supported HPHZ Schiff base complexes of iron(III) ions showed 64.0% conversion for phenol and 81.3% conversion for cyclohexene at a molar ratio of 1∶1∶1 of substrate to catalyst and hydrogen peroxide, but unsupported complexes of iron(III) ions showed 55.5% conversion for phenol and 66.4% conversion for cyclohexene at 1∶1∶1 molar ratio of substrate to catalyst and hydrogen peroxide. The product selectivity for catechol (CTL) and epoxy cyclohexane (ECH) was 90.5% and 96.5% with supported HPHZ Schiff base complexes of iron(III) ions, but was found to be low with cobalt(II) and nickel(II) ions complexes of Schiff base. The selectivity for catechol (CTL) and epoxy cyclohexane (ECH) was different with studied metal ions and varied with molar ratio of metal ions in the reaction mixture. The selectivity was constant on varying the molar ratio of hydrogen peroxide and substrate. The energy of activation for epoxidation of cyclohexene and phenol conversion in presence of polymer supported HPHZ Schiff base complexes of iron(III) ions was 8.9 kJ mol^?1 and 22.8 kJ mol^?1, respectively, but was high with Schiff base complexes of cobalt(II) and nickel(II) ions and with unsupported Schiff base complexes.     

Formation of the second superhydrophobic shell around an encapsulated metal ion: synthesis, X-ray structure and electrochemical study of the clathrochelate and bis-clathrochelate iron(II) and cobalt(II, III) dioximates with ribbed perfluoroarylsulfide substituents

The nucleophilic substitution of six chlorine atoms of the n-butylboron-capped clathrochelate iron and cobalt(II) precursors with perfluoroarylthiolate anions afforded the hexaperfluoroarylsulfide macrobicyclic iron and cobalt(II) tris-dioximates. The complexes obtained are soluble in aromatic and aliphatic hydrocarbons as well as in polar aprotonic solvents due to the presence of the superhydrophobic fluorine-containing molecular periphery. As it follows from the X-ray data for five iron and cobalt mono- and bis-clathrochelates, the geometry of their macrobicyclic frameworks is affected by both the nature of an encapsulated metal ion and that of the ribbed substituents. Bis-capping fragment Co(II)O(6) of the Co(III)Co(II)Co(III) bis-clathrochelate possesses a trigonal antiprismatic geometry, all the Co(II)N(6) coordination polyhedra are trigonal-prismatic, and those of the encapsulated iron(II) and cobalt(III) ions are intermediate between them. The wide range of Co-N distances as well as the significant shifts of the encapsulated cobalt(II) ions from the centres of their N(6)-coordination polyhedra were explained by the Jahn-Teller distortion. The EPR and magnetometry data are also characteristic of the low-spin cobalt(II) complexes with this distortion. The parameters of the (57)Fe M?ssbauer spectra of the iron macrobicycles are characteristic of the low-spin iron(II) complexes. The cyclic voltammograms (CVs) for the complexes studied contain the one-electron oxidation and reduction waves assigned to metal-centered redox-processes. The Fe(2+/3+) and Co(2+/3+) oxidations are quasi-reversible or irreversible. The anionic clathrochelate species resulting from the reversible Co(2+/+) reductions are stable on the CV time scale, whereas their iron(I)-containing analogs are unstable.     

Analytical applications of a liquid anion-exchanger for the separation of uranium(IV) in malonate solution

Uranium was quantitatively extracted with 4% Amberlite LA-1 in xylene at pH 2.5-4.0 from 0.001 M malonic acid. It was stripped from the organic phase with 0.01 M sodium hydroxide and determined spectrophotometrically at 530 nm as its complex with 4-(2-pyridylazo) resorcinol. Of various liquid anion-exchangers tested, Amberlite LA-1 was found to be best. Uranium was separated from alkali and alkaline earth metal ions, thallium(I), iron(II), silver, arsenic(III) and tin(IV) by selective extraction, and from zinc, cadmium, nickel, copper(II), cobalt(II), chromium(III), aluminium, iron(III), lead, bismuth, antimony(III) and yttrium by selective stripping. The separation from scandium, zirconium, thorium and vanadium(V) was done by exploiting differences in the stability of chloro-complexes.     

Determination of cobalt(II), copper(II) and iron(II) by ion chromatography with chemiluminescence detection

An optimized flow-injection manifold for the chemiluminescence determination of cobalt(II), copper(II), iron(II) and chromium(III) by their catalytic effect on the luminol reaction is described. Detection limits are 0.0006, 0.08, 0.3 and 0.1 ng ml^?1, respectively. The suppression effect of several carboxylic acids on the emission intensity is discussed. A procedure for the separation of cobalt(II), copper(II) and iron(II) on a low-capacity, silica-based cation-exchange column, using 5 mM oxalic acid at pH 4.2 as the mobile phase and post-column detection via the luminol reaction, is also described. Detection limits for cobalt(II) and copper(II) are 0.01 and 5 ng ml^?1, respectively.     

Synthesis and characterization of iron(III), manganese(II), cobalt(II), nickel(II), copper(II) and zinc(II) complexes of salicylidene-N-anilinoacetohydrazone (H2L1) and 2-hydroxy-1-naphthylidene-N-anilinoacetohydrazone (H2L2)

Salicylidene-N-anilinoacetohydrazone (H(2)L(1)) and 2-hydroxy-1-naphthylidene-N-anilinoacetohydrazone (H(2)L(2)) and their iron(III), manganese(II), cobalt(II), nickel(II), copper(II) and zinc(II) complexes have been synthesized and characterized by IR, electronic spectra, molar conductivities, magnetic susceptibilities and ESR. Mononuclear complexes are formed with molar ratios of 1:1, 1:2 and 1:3 (M:L). The IR studies reveal various modes of chelation. The electronic absorption spectra and magnetic susceptibility measurements show that the iron(III), nickel(II) and cobalt(II) complexes of H(2)L(1) have octahedral geometry. While the cobalt(II) complexes of H(2)L(2) were separated as tetrahedral structure. The copper(II) complexes have square planar stereochemistry. The ESR parameters of the copper(II) complexes at room temperature were calculated. The g values for copper(II) complexes proved that the Cu-O and Cu-N bonds are of high covalency.     

Rapid spectrophotometric determination of cobalt after extraction using oximidobenzotetronic acid

A spectrophotometric method based on the extraction of cobalt with benzene solutions of oximidobenzotetronic acid (OBTA) is proposed for the estimation of 0.2-3.0 ppm of cobalt. The 3:1 OBTA : Co complex containing cobalt(III) has its absorption maximum at 430 nm; its molar absorptivity in benzene is 1.82 x 10(3)L. mole(-1). mm(-1). Since the blue iron(II) complex is not extracted into benzene, iron(II) and cobalt(II) can be separated and determined spectrophotometrically.     

Highly sensitive spectrofluorometry of europium(III) as its benzoyltrifluoroacetone complex with trioctylphosphine oxide by means of solvent extraction and vacuum sublimation

Summary A new method for the highly sensitive fluorometric determination of europium(III) as its benzoyltrifluoroacetone (BFA) complex with trioctylphosphine oxide (TOPO) without uncombined BFA in n-hexane has been established by means of solvent extraction and vacuum sublimation. The effect of various factors on the fluorescence intensity of europium(III) was investigated. The fluorescence intensity was measured at 620 nm against rhodamine B as an internal standard under the excitation at 335 nm. It was found that a heating treatment gave rise to the enhancement of the fluorescence intensity for about twice times compared with that without heating treatment. Excellent linearity of the calibration curve of europium(III) was obtained in the range of 0–100 ppb. A few ppb of europium(III) can still be detected with this method. All 13 rare earth metals and cobalt(II) tested gave a somewhat positive error. Aluminium(III), iron(III), and copper(II) caused a negative error. The interference of aluminium(III) and iron(III) was removed by extraction with 0.1 mol/l 8-quinolinol in chloroform at pH 4.0, while the problem of cobalt(II) and copper(II) was solved by masking with 0.1 mol/l Na₂S₂O₃ in aqueous solution.

---

Hochempfindliche spektrofluorimetrische Bestimmung von Europium(III) als Benzoyltrifluoracetonkomplex mit Trioctylphosphinoxid mit Hilfe der Lösungsextraktion und Vakuumsublimation

     

Extraction of palladium(II) from hydrochloric acid solutions by (RS)-1-(4-chlorophenyl)-4,4-dimethyl-3-(1H-1,2,4-triazol-1-ylmethyl)-pentan-3-ol

The extraction properties of (RS)-1-(4-chlorophenyl)-4,4-dimethyl-3-(1H-1,2,4-triazol-1-ylmethyl)-pentan-3-ol (with chloroform as a diluent) with respect to palladium(II) were studied. Palladium(II) was found to be efficiently extracted by the reagent from 0.1–6 M HCl solutions by the coordination mechanism. The rate of palladium(II) recovery depends on the hydrochloric acid and chloride ion concentrations in the aqueous phase. Conditions for the selective separation of palladium(II) and copper(II) from nickel(II), cobalt(II), and iron(III) were determined.     

Metal complexes of anti-inflammatory drugs—I. Complexes of iron(III), cobalt(II), nickel(II), copper(II) and zinc(II) with 4-hydroxy-3-(5-methyl-3-is

The preparation, spectroscopic and magnetic properties are reported for complexes of iron(III), cobalt(II), nickel(II), copper(II) and zinc(II) with th