High-performance titanium dioxide photocatalyst on ordered mesoporous carbon support

Anatase TiO₂ photocatalysts supported with the ordered mesoporous carbon, CMK-3, were synthesized by the incorporation of TiO₂ into CMK-3 followed by heating at 700 °C. The structural properties of the TiO₂ on CMK-3 were investigated by X-ray diffraction, nitrogen physisorption and electron microscopy techniques. In particular, TiO₂ was observed both inside and the external surface of CMK-3. The photocatalytic activity of TiO₂ on CMK-3 under UV-light exhibited higher efficiency in removing the Rhodamine 6G dye solution than the commercial photocatalyst P25 and TiO₂ on activated carbon. It was attributed to the synergistic effect of large surface area adsorption provided by mesoporous CMK-3 and the distinctive location of TiO₂ on the external surface of CMK-3.     

不同孔径的介孔碳分子筛对VB12的吸附性质研究

摘要利用SBA-15为模板, 在不同温度下合成了孔径大小在3.7(CMK-3-100)和6-3 nm(CMK-3-150)之间的介孔碳， 以其作为吸附剂, 研究了它们在水溶液中对VB12的吸附作用. 结果表明, CMK-3-130与CMK-3-100和CMK-3-150相比， 表现出对VB12最大的吸附能力(吸附能力为412.5 mg/g), 这是因为它有比较高的有序结构和比较大的孔容.     

介孔碳CMK-3对苯酚的吸附动力学和热力学研究

研究了介孔碳CMK-3对苯酚的吸附性能, 与传统商用活性碳(CAC)进行了比较, 结果表明, CMK-3比CAC的吸附量大、吸附速率快、达到平衡时间短, 是一种较好的吸附剂. 同时探讨了介孔碳CMK-3对苯酚的吸附热力学和动力学特征. CMK-3对苯酚的吸附行为可用Langmuir和Freundlich等温式进行描述, 相关性都较好, 但更符合Freundlich经验公式. 分别采用模拟一阶反应和二阶反应模型考察了吸附动力学, 并计算了这些动力学模型的速率常数. 模拟二级反应模型和实验数据之间有较好的相关性. 分别计算了热力学参数ΔG0, ΔS0和ΔH0, 结果表明, CMK-3对苯酚的吸附过程是吸热和自发的.     

Adsorption of U(VI) from aqueous solution by sulfonated ordered mesoporous carbon

The sulfonated mesoporous carbon (CMK-3-SO₃H) prepared by functionalizing mesoporous carbon (CMK-3) via vapor transfer method has been explored for the removal and recovery of uranium from aqueous solutions. The influences of different experimental parameters such as solution pH, initial concentration, contact time and temperature on adsorption were investigated. The results showed that CMK-3-SO₃H has the highest uranium sorption capacity at initial pH of 5.0 and contact time of 120 min, and the adsorption process could be better described by the pseudo-second-order model and Langmuir isotherm. Selective adsorption studies showed that the CMK-3-SO₃H could selectively remove of U(VI), and the selectivity coefficients of mesoporous carbon in the presence of co-existing ions, Mg(II), Zn(II), Mn(II), Cu(II), Ni(II), Sr(II) and Hg(II) improved after functionalization.     

Adsorption of aqueous alkylphenol ethoxylate surfactants by mesoporous carbon CMK-3

Mesoporous carbon, CMK-3, was prepared using hexagonal SBA-15 mesoporous silica as the template and the adsorption of nonylphenol ethoxylates (NPE) onto CMK-3 was investigated. The adsorption process was well described using pseudo-second-order kinetics. At initial NPE concentrations of 107 and 530 mg l(-1), the adsorption rate constants were found to be 5.6 x 10(-3) and 8.7 x 10(-4) g mg(-1) min(-1), indicating that a higher initial concentration or adsorption amount resulted in a lower adsorption rate. NPE adsorption onto CMK-3 fitted a Langmuir-Freundlich model and the maximum amounts of NPE absorbed at 15, 25, and 35 degrees C were 923, 720, and 463 mg g(-1), suggesting an elevated adsorption capacity of CMK-3 for NPE with decreased adsorption temperature. In addition, increasing adsorption temperature led to the change of the adsorption model from the Langmuir-Freundlich to the Langmuir model. N2 adsorption results showed that the adsorption of NPE led to a decrease in the mesopore volume of CMK-3. However, the pore width of NPE-loaded CMK-3 was found to be identical to that of CMK-3.     

介孔碳材料CMK-3的合成及其吸附性能研究——介绍一个综合化学实验

介绍一个集物理化学、分析化学和无机化学为一体的综合实验——介孔碳材料CMK-3的合成及其吸附性能研究。实验通过合成具有高比表面积的介孔碳材料CMK-3,运用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和氮气吸附/脱附技术表征材料的形貌和多孔结构;考察了介孔碳材料CMK-3对水溶液中次甲基蓝染料分子的吸附性能。     

Effect of the conditions of the matrix carbonization of sucrose on the structure and adsorption properties of mesoporous carbon materials

A study was carried out on the effect of the conditions of the matrix carbonization of sucrose in MCM-48 and SBA-15 silica mesoporous molecular sieves on the structure and adsorption properties of the resultant CMK-1 and CMK-3 mesoporous carbon molecular sieves. CMK-3 was found to be a structurally similar replica of SBA-15. An exact replica is not formed in the case of MCM-48. This failure is attributed to considerable deformation of the matrix during the carbonization process due to the bicontinuous pore system and thinner framework walls. This is probably related to transformation of the carbon material into a low symmetry product upon detemplating of the C/MCM-48 composite (dissolution of the silica). Mesoporous carbon materials were obtained with good adsorption structure features. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 44, No. 6, pp. 365–370, November–December, 2008.     

Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.     

Structural and sorption properties of carbon replicas obtained by matrix carbonization of organic precursors in SBA-15 and KIT-6

We have carried out a comparative study of matrix carbonization of some organic precursors (sucrose, polydivinylbenzene, polyphenol-formaldehyde, polyacrylonitrile, acetonitrile) in SBA-15 and KIT-6 silica mesoporous molecular sieves. We have shown that carbon mesoporous molecular sieves of the CMK-8 type, obtained in KIT-6 mesopores, have better adsorption characteristics due to the features of the three-dimensional cubic structure, the larger pore volume and thickness of the walls of the framework. The maximum micropore volume is observed in CMK-3 and CMK-8, obtained by carbonization of polyphenol-formaldehyde and polydivinylbenzene, while the greatest specific surface area is observed on carbonization of sucrose, where the maximum hydrogen adsorption capacity is achieved at a level of ∼1.4 wt.% (77 K, 1 atm). We show that the mesopore surface coverage by hydrogen in carbon mesoporous molecular sieves increases as the degree of graphitization increases.     

Kinetics and Thermodynamics of Adsorption of VB12 onto Mesoporous Carbon Coated with PMMA

Ordered mesoporous carbons CMK-3, CMK-1 coated with poly(methyl methacrylate)(PMMA)(CMK-3- PMMA and CMK-1-PMMA) and pristine mesoporous carbons CMK-3, CMK-1 were employed to adsorb vitamin B12(VB12) from water solution. Adsorption isotherm and kinetics of adsorption were investigated via batch experi- ments. It was found that the adsorption capacity of VB12 at 30, 40 and 50 °C can reach 688.2, 572.4 and 428.7 mg/g, respectively. The adsorption isotherm can be described by Langmuir model. The pseudo first- and second-order kinetic models were employed to fit the dynamic adsorption. It was found that the dynamic adsorption follows the pseudo second-order model. The thermodynamic equilibrium coefficients obtained at different temperatures were used to evaluate the thermodynamic constants ΔG0, ΔH0 and ΔS0. The negative value of Gibbs free energy, ΔG0 indicates that the adsorption occurred via a spontaneous process. The increase in the value of –ΔG0 with increasing temperature indicates that higher temperatures were favourable to the sorption process. The enthalpy values of ΔH040 kJ/mol(66.36 kJ/mol and 56.43 kJ/mol) for CMK-3-PMMA and CMK-1-PMMA confirm that chemisorption were involved in the adsorption process. This is consistent with the IR spectra and is another evidence for the formation of hydrogen bond between PMMA in the pore of CMK-3 and VB12.     

Effect of the chemical and structural modification of CMK-3 mesoporous carbon molecular sieve on hydrogen adsorption

The effect of the conditions of postsynthetic modification of CMK-3 carbon mesoporous molecular sieves on their structural and adsorption properties was studied. The specific surface, volume, pore size, and hydrogen adsorption are markedly enhanced upon activation of CMK-3 by thermal, steam, and chemical treatment using H₂, CO₂, H₂O₂, and HNO₃. Analysis of the occupancy density of the mesopore surface indicated increased hydrogen adsorption capacity of the hydrogen-activated carbon surface of CMK-3. Hydrogen adsorption is increased from 1.20 to 2.23 mass % at 1 atm and 77 K by steam treatment. This effect may be employed to create efficient carbon MMS adsorbents, including composite adsorbents, for the accumulation and storage of hydrogen at high pressure (adsorption >6 mass %).     

C60大量、快速分离和电喷雾电离质谱检测

本文用配合沉淀和活性炭吸附相结合的方法，从高级富勒烯含量较高的混合物中，大量、快速分离Ｃ６０，并用电喷雾电离质谱对分离产物进行检测     

锂离子电池电极用规整中孔碳分子筛的电化学特性

采用SEM, N₂吸附技术和XRD对首次用于锂离子电池电极的规整中孔碳分子筛CMK-5的表面形态、孔结构和晶体结构进行了表征. 利用恒电流仪和伏安循环法研究了CMK-5的电化学性质, 并与传统的阳极材料石墨进行对比. 结果表明, CMK-5具有良好的可逆特性, 在第三次充电-放电循环中贮能密度仍可达525 mAh/g, 由于CMK-5具有特殊的中孔结构, 因而更适合用作快速充电-放电循环材料. 一个有趣的现象是, CMK-5在伏安循环的正值部分没有出现极值, 这与传统阳极材料显著不同. 另外, 还利用XPS和XRD考察了CMK-5的充电-放电特性.     

Chromium-based metal–organic framework/mesoporous carbon composite: synthesis,characterization and CO<Subscript>2</Subscript> adsorption

New composites of a water-stable chromium-based metal organic framework MIL-101 and mesoporous carbon CMK-3 were in situ synthesized with different ratios of MIL-101 and CMK-3 using the hydrothermal method. The composites as well as the parent materials were characterized by X-ray diffraction, thermo gravimetric analysis, scanning electron microscope, transmission electron microscope and nitrogen/carbon dioxide adsorption isotherms. The hybrid material possesses the same crystal structure and morphology as its parent MIL-101, and exhibits an enhancement in CO₂ adsorption uptakes when compared to MIL-101 and CMK-3. The increase in CO₂ uptakes was attributed to the combined effect of the formation of additional micropores, the enhancement of micropore volume and the activation of unsaturated metal sites by CMK-3 incorporation.     

介孔L材料CMK-3对甲基紫的吸附性能

合成了高度有序的具有二维六方(P6mm)结构的介孔碳材料CMK-3;利用X射线衍射分析了CMK-3的晶体结构,利用氮气吸脱附(BET)试验测定了孔体积;测定了CMK-3对水溶液中甲基紫的吸附行为,考察了不同pH、温度及浓度下水溶液中甲基紫的静态吸附行为,并分析了酸性、中性、碱性条件下吸附剂对甲基紫和罗丹明B混合溶液的竞...     

In situ introduction of dispersed metallic Ag nanoparticles into the channels of mesoporous carbon CMK-3

An in situ reduction method has been developed to fabricate metallic Ag nanoparticles inside the channels of mesoporous carbon CMK-3.This approach combines function of the CMK-3 surface by oxidation using HNO_3 with the subsequent absorption of Ag~ . The resultant nanocomposite materials were characterized by nitrogen adsorption,X-ray diffraction,Auger electron spectroscopy and transmission electron microscopy.Compared with the conventional impregnation method,our approach shows that Ag nanoparticles of 2-4 nm can be uniformly incorporated into CMK-3.     

Synthesis and characterization of nanocast silica NCS-1 with CMK-3 as a template

Nanocast silica (NCS-1) was synthesized by a casting process by employing the mesoporous carbon CMK-3 (the replica of SBA-15) as a template, tetraethoxysilane (TEOS) as the silica source, and hydrochloric acid (HCl) as the catalyst. The ordered carbon template was removed by employing different methods, such as calcination, thermal treatment followed by calcination, and controlled combustion. According to XRD and TEM characterization, NCS-1 exhibits an ordered structure with hexagonal symmetry and retains the morphology of the original SBA-15 used for the synthesis of CMK-3 over two replication steps on the nanometer scale. This demonstrates the well-connected porosity in CMK-3 type carbon, which can be used as a mold to synthesize mesostructured materials. The nitrogen adsorption isotherms generally show type IV shape, indicating mesoporous characteristics. The structure of NCS-1 is strongly influenced by variables of the nanocasting process, such as the loading amount of silica, hydrolysis temperature, and carbon removal methods. The surface area, pore size, and pore volume of NCS-1 can be tuned to a certain range by varying these parameters.     

有序介孔炭负载铜基催化剂Cu/CMK-3用于气相甲醇氧化羰基化反应

通过纳米浇铸法合成了有序介孔炭CMK-3,再通过浸渍法制备了Cu/CMK-3催化剂,并将其用于气相甲醇氧化羰基化反应。N2吸附-脱附测试、X射线衍射(XRD)以及透射电镜(TEM)的表征结果表明,Cu/CMK-3具有序介孔结构,活性Cu物种均匀分散于CMK-3的表面及孔道中,粒径为10~20 nm,远小于相同条件下制备的铜/活性炭(Cu/AC)催化剂。固定床反应器的活性评价结果显示450℃下制备的Cu/CMK-3催化活性最高,反应10 h内碳酸二甲酯(DMC)的时空收率(STY)达到286 mg·g^-1·h^-1,选择性为76%。长周期活性评价结果表明Cu/CMK-3稳定性较相同条件下制备的Cu/AC有大幅提高,50 h内DMC的STY降低了20%,75 h内降低了28%。     

化学气相沉积法合成Fe/CMK-5及其对溶菌素的吸附性能

以SBA-15为模板,二茂铁为碳源,利用化学气相沉积(CVD)法合成了Fe/CMK-5复合材料.用粉末X射线衍射、低温N2吸附、热重分析、透射电镜等对复合材料进行了表征.结果表明复合材料中碳以CMK-5结构存在,Fe颗粒均匀地分布在CMK-5的骨架中,通过调节CVD时间可改变Fe/CMK-5的结构参数.在pH值为11的缓冲溶液中研究了Fe/CMK-5系列复合材料对溶菌素(lysozyme)的吸附性能,考察了溶菌素在Fe/CMK-5孔道内部的结构稳定性以及在不同pH值溶液中的泄露量.     

双孔道管状有序介孔炭对维生素B12的吸附缓释性能

通过纳米铸型法,以硅基介孔分子筛SBA-15为模板,糠醇为碳源,草酸作为聚合催化剂合成了具有双孔道管状有序介孔炭CMK-5.利用粉末X射线衍射(XRD)、扫描电子显微镜(SEM)和氮气物理吸附法等对其结构进行了表征.结果表明合成的CMK-5具有有序结构,比表面积和孔容积分别高达1856 m2·g-1和2.10 cm3·g-1,在3.1和5.5nm具有集中的双孔分布.由于独特的双孔道结构特点,CMK-5在120 min内快速吸附维生素B12至平衡,吸附量高达943 mg·g-1,远高于商用活性炭.CMK-5吸附维生素B12后可以直接用于缓释,动态缓释浓度维持在～9 mg·L-1,适用于维生素B12分子在人体内的缓释.