化学溶液法制备的Bi3.25La0.75Ti3O12和Bi3.25Nd0.75Ti3O12薄膜的光学特性

采用化学溶液方法在(111)Pt／Ti/SiO2/Si衬底上制备了Bi3.25La0.75Ti3O12(BLT)和Bi3.25Nd0.75Ti3O12(BNT)薄膜．x射线衍射测试表明，两种薄膜都为单一的层状钙钛矿结构．扫描电子显微镜分析显示，BNT薄膜由大而均匀的棒状晶粒组成，BLT薄膜的组成晶粒则较小．采用紫外一近红外椭圆偏振光谱仪测试了200-100nm波长范围的椭圆偏振光谱，拟合得到薄膜的光学常数(折射率和消光系数)和厚度，确定BLT薄膜的禁带宽度分别为4．30和3．61eV，并采用单电子振子模型分析了薄膜在带间跃迁区的折射率色散关系．     

MOD法制备Bi4-xLaxTi3O12铁电薄膜及其谱图分析

采用有机金属沉积法(MOD)制备了Bi4Ti3O12(BIT)和Bi3.25La0.75Ti3O12(BLT)前驱体溶液,分别在单晶硅基片上制备了BIT和BLT铁电薄膜.前驱体溶液的干凝胶粉体和铁电薄膜分别用红外光谱(FTIR)、拉曼光谱和环境扫描电镜(ESEM)进行了表征.结果表明600℃时晶粒实现了由焦绿石相向类钙钛矿相结构的完全转变;温度升高,晶粒尺寸增大,薄膜结晶效果得到改善;引入镧使Ti-O和Bi-O键吸收峰位置向低波数频移,高温时频移率较大;500℃热处理时,干凝胶中乙二醇甲醚、乙酰丙酮完全分解,温度超过600℃后,残留的水及硝酸根离子挥发或分解.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO2/Si衬底上制备出Bi4Ti3O12和Bi3.25La0.75Ti3O12薄膜,研究了La掺杂对Bi4Ti3O12薄膜的晶体结构、铁电性能和疲劳特性的影响,发现La掺杂没有改变Bi4Ti3O12薄膜的基本晶体结构,并且提高了Bi4Ti3O12铁电薄膜的剩余极化值和抗疲劳性能,对La掺杂改善Bi4Ti3O12铁电薄膜性能的机理进行了讨论.     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi_3.25La_0.75Ti₃O₁₂铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi_3.25La_0.75Ti₃O₁₂薄膜未能充分晶化，晶粒细小且有非晶团聚，介电与铁电性能均较差.高于550℃退火处理的Bi_3.25La_{0.75 关键词： 铁电薄膜 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ Sol-Gel工艺     

La,V共掺杂的Bi_4Ti_3O_(12)铁电薄膜的溶胶-凝胶法制备及性能测试

采用溶胶-凝胶(sol-gel)工艺在Pt/TiO2/SiO2/p-Si(100)衬底上制备出Bi4Ti3O12(BIT)和Bi3.25La0.75Ti2.97V0.03O12(BLTV)铁电薄膜,研究了La,V共掺杂对BIT薄膜的晶体结构和电学性能的影响.BIT薄膜为c轴择优取向,BLTV薄膜为随机取向,拉曼光谱分析表明V掺杂降低了TiO6(或VO6)八面体的对称性,也增强了Ti—O键(或V—O键)杂化.BLTV薄膜的剩余极化Pr为25.4μC/cm2,远大于BIT薄膜的9.2μC/cm2,表现出良好的铁电性能.疲劳、漏电流测试显示BLTV薄膜具有优良的抗疲劳特性和漏电流特性,表明La,V共掺杂能有效地降低薄膜中的氧空位.     

Si基Bi4Ti3O12铁电薄膜的制备与特性研究

采用sol-gel工艺,在分层快速退火的工艺条件下成功地制备了高质量Si基BiTi3O12铁电薄膜.研究了Si基Bi4Ti3O12薄膜的生长行为、铁电性能、C-V特性和疲劳特性.研究表明:Si基Bi4Ti3O12薄膜具有随退火温度升高沿c轴择优生长的趋势;退火温度通过影响薄膜的晶粒尺寸、生长取向和薄膜中载流子的浓度来改变Si基Bi4Ti3O12薄膜的铁电性能;Ag/Bi4Ti3O12/p-Si异质结的C-V特性曲线呈现顺时针回滞,可以实现极化存储;109次极化反转后Bi4Ti3O12薄膜的剩余极化仅下降12%,具有较好的疲劳特性.     

退火气压对Bi3.25La0.75Ti3O12铁电薄膜的微观结构和铁电性能的影响

采用sol-gel法在Pt/TiO₂/SiO₂/p-Si(100)衬底上制备了Bi_3.25La_0.75Ti₃O₁₂(BLT)铁电薄膜,研究了在750 ℃时不同退火气压(p_{O2:10^-4—3 atm)对薄膜微观结构和电学性能的影响.XRD和拉曼光谱结果表明在10^-4和3 atm氧气压下退火 关键词： 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ 铁电性能 sol-gel法 正交化度     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi3.25La0.75Ti3O12铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi3.25La0.75Ti3O12薄膜未能充分晶化,晶粒细小且有非晶团聚,介电与铁电性能均较差.高于550℃退火处理的Bi3.25La0.75Ti3O12薄膜表面平整无裂纹,晶粒均匀,无焦碌石相或其他杂相,薄膜为多晶生长,具有较好的介电与铁电性能,4V电压下的漏电流密度低于2×10-8A/cm2.随退火温度升高,晶化程度的提升和晶粒尺寸的增大使薄膜的剩余极化增大而矫顽电场降低.600℃退火处理的Bi3.25La0.75Ti3O12薄膜显示了优于Bi4Ti3O12薄膜的铁电性能,其剩余极化Pr和矫顽电场Ec分别达到17.5μC/cm2和102kV/cm.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

退火气压对Bi3.25La0.75Ti3O12铁电薄膜的微观结构和铁电性能的影响

采用sol-gel法在Pt/TiO2/SiO2/p-Si(100)衬底上制备了Bi3.25La0 75Ti3O12(BLT)铁电薄膜,研究了在750 ℃时不同退火气压(Po2:10-4-3 atm)对薄膜微观结构和电学性能的影响.XRD和拉曼光谱结果表明在10-4和3 atm氧气压下退火的薄膜晶化度明显降低.同时,XRD结果反映出10-1atm氧气压下退火的薄膜具有a轴择优取向.FSEM截面形貌显示0.1 atm氧气压下退火的薄膜由与a轴取向相对应的柱状晶粒构成,1 atm氧气压下退火的薄膜为由随机取向相对应的斜杆状晶粒构成.薄膜的微观结构最终影响了其铁电性能.0.1 atm氧气压下退火的薄膜具有最大的剩余极化值(Pr=17.8 Μc/cm2和最小的矫顽场强(Ec=73.6 Kv/cm),以及良好的抗疲劳特性.     

Structural and optical properties of Bi3.25Nd0.75Ti3O12 ferroelectric thin films

Ferroelectric Bi_3.25Nd_0.75Ti₃O₁₂ (BNT) thin films were grown on (111)Pt/Ti/SiO₂/Si substrates by a chemical solution method. The films were composed of large rod-like grains. XRD and Raman spectroscopy measurements showed they were polycrystalline perovskite structure with a good crystallinity. Pt/BNT/Pt capacitors had been fabricated and showed good ferroelectricity. The optical constants (n, k) of BNT thin films in the wavelength ranges of 0.2–1.7 μm and 2.5–11.4 μm were obtained by spectroscopic ellipsometry measurements. The dispersion of the refractive index in the interband transition region followed the single electronic oscillator model. The optical band gap was found to be about 3.61 eV. PACS 77.84.-s; 78.20.Ci; 77.80.-e     

Electrical studies on Zr-modified Bi3.25La0.75Ti3O12: a promising FRAM ceramic

Zr-modified Auruvillius family of lanthanum bismuth titanate, namely Bi_3.25La_0.75Ti_3?xZr_xO₁₂ (BLTZ, x = 0, 0.1, 0.3, 0.5, 0.7 and 1), was prepared by solid-state reaction method. Dielectric properties of the ceramics were studied as a function of temperature. Hysteresis measurements were also performed. Among the composition, Bi_3.25La_0.75Ti_2.9Zr_0.1O₁₂ (BLTZ1) showed large remnant polarization compared to the promising ceramic, namely Bi_3.25La_0.75Ti₃O₁₂. The results were corroborated with the pyroelectric, electric polarization and Raman spectroscopic data.     

Retention characteristics of Au/Bi3.25La0.75Ti3O12/Si metal-ferro- electric-semiconductor structure

Lanthanum-substituted bismuth titanate (Bi_3.25La_0.75Ti₃O₁₂) (BLT) thin films were deposited on p-type Si(100) substrates using a chemical solution deposition process. The ferroelectric and dielectric properties of the films with an Au/BLT/Si structure were investigated. It was found that retention behaviors of the capacitors after polling with a negative and positive voltage were very different. The capacitor at an accumulation state exhibited a better retention characteristic than that at a depletion state. A rapid loss of memory for the capacitor at depletion state was found and attributed to the depolarization fields inside the ferroelectric film. It is proposed that the interaction between injected charges and ferroelectric polarization plays a role in the retention properties of the MFS capacitors.     

Stress and its related effects on the fatigue behavior of Bi3.25La0.75Ti3O12 thin films

The effects of external stress cooperated with temperature, measuring frequency and measuring electric field on the fatigue properties of Bi_3.25La_0.75Ti₃O₁₂ thin films are investigated. The fatigue properties can be improved by the external stress (both tensile and compressive). The larger the stress is, the more obvious the improvement is. Meanwhile, the stress-induced improvement is more distinct in the films annealed at a higher temperature. In addition, when measured at a higher frequency or at a larger electric field, the films show better fatigue properties, and the improvement caused by stress is more evident. The experimental results can be explained well by the mechanism in which the charged defects pin the domain walls during electric cycling.     

Large nonlinear optical response of polycrystalline Bi3.25La0.75Ti3O12 ferroelectric thin films on quartz substrates

We measure the nonlinear susceptibility of Bi(3.25)La(0.75)Ti(3)O(12) (BLT) thin films grown on quartz substrates using the Z-scan technique with picosecond laser pulses at a wavelength of 532 nm. The third-order nonlinear refractive index coefficient gamma and absorption coefficient beta of the BLT thin film are 3.1 x 10(-10) cm(2)/W and 3 x 10(-5) cm/W, respectively, which are much larger than those of most ferroelectric films. The results show that the BLT thin films on quartz substrates are good candidate materials for applications in nonlinear optical devices.     

烘烤温度对溶胶-凝胶法制备镧掺杂钛酸铋薄膜结构与铁电性质的影响

采用溶胶-凝胶法，在保持薄膜结晶温度和有机物分解温度相同情况下，发现烘烤温度（即溶剂的挥发温度）对镧掺杂钛酸铋薄膜的晶体结构、表面形貌和铁电性质均产生重要影响.在较低烘烤温度下得到的薄膜（117）择优取向明显.但随着烘烤温度增加，薄膜的（117）择优取向逐渐减弱.薄膜的表面晶粒形貌则从棒状逐渐转变为盘状.还测量了薄膜的铁电性质，发现在250℃烘烤温度下得到的薄膜具有最大的剩余极化强度，2Pr为28.4μC/cm2.对实验现象进行了定性解释. 关键词： 溶胶-凝胶法 烘烤温度 铁电薄膜     

Absorption gratings in ferroelectric Bi4Ti3O12

4 Ti₃O₁₂. Basic properties of absorption gratings in this crystal are investigated with beam-coupling experiments. Depending on the grating spacing, wavelength, and intensity of the writing beams, an absorption grating in our sample can be either in phase or shifted by 180° with respect to the light pattern. The formation mechanism of absorption grating is discussed and proposed to originate from a shallow-trap effect. Received: 10 February 1997     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术,利用LSCO/CeO2/YSZ多异质缓冲层,在Si(100)基片上成功地制备了c轴一致取向的Bi3.15Nd0.85Ti3O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构、取向和形貌特征,考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响,确定了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型的蝴蝶形曲线,表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与薄膜取向的相关性.