Intrachannel pulse interactions in dispersion-managed transmission systems: timing shifts

Nonlinear intrachannel interactions responsible for timing shifts in a transmission system with strong periodic dispersion management are investigated. Formulas describing the evolution of the timing shift are obtained for general bit patterns. When average dispersion is negligible, the timing shift is shown to grow linearly in distance in a system with loss and lumped amplification, whereas in a lossless system the timing shift is sufficiently small at every chirp-free point. The analysis agrees with direct numerical simulations.     

Collision-induced timing jitter in dispersion-managed WDM soliton system with filtering

Taking into account the randomicity of collision positions and the arbitrary encoding of data in channel,the influences of different dispersion management on collision-induced timing jitter in a filtered wavelength division multiplexing (WDM) soliton system are obtained statistically and numerically by applying a set of coupled ordinary differential equations which are derived through variational procedure. The optimal dispersion managements which can greatly reduce the collision-induced timing jitter are found. The multi-channel collision-induced timing jitters in a filtered WDM soliton system are given with an optimal dispersion management and constant dispersion.     

Duty-cycle division multiplexing (DCDM)

A multiplexing technique, which is based on duty-cycle division, is proposed. The channel multiplexing and demultiplexing are performed electrically at the single user bit rate, which is very economic. In a three-user system (3×10 Gb/s), the simulation results show that the best receiver sensitivity value achieved is −30.1 dBm with an optical signal-to-noise ratio (OSNR) of 22.3 dB, while the chromatic dispersion tolerance ranges from 192 to 280 ps/nm. Migration from 30 to 120 Gb/s is achieved with the penalty of 6.4 and 5.2 dB in the receiver sensitivity and OSNR, respectively, for the worst user.     

Optical 3R regeneration of 40 Gbit/s degraded data signals

A 40 Gbit/s optical 3R regenerator is proposed and demonstrated. The 3R regenerator consists of a dual-ring injection mode-locked fiber ring laser as the clock recovery module and an electroabsorption modulator (EAM) as the decision gate. The clock recovery module extracts the optical short pulse clock with low timing jitter from degraded 40 Gbit/s optical data streams, while the decision gate restores their signal quality. A numerical model describing the cross-absorption modulation effect in a bulk EAM is developed to explore the operating conditions, such as bias voltage, pump signal power. The timing jitter tolerance for the EAM optical gate is also investigated. Significantly improvement of BER is obtained from 40 Gbit/s RZ signals which are degraded by polarization mode dispersion or chromatic dispersion.     

Performance comparison of wavelet packet transform based and conventional coherent optical OFDM transmission system

In this work, the performance of WPT-COOFDM system is investigated and compared to that of FFT-COOFDM system over a fiber link. Simulation results show that the longer length of wavelet filters achieve a better performance, whereas the complexity is higher. For different wavelet mother functions employed in WPT-COOFDM systems, the chromatic dispersion robust of John64E wavelet outperforms that of other wavelets, and which could be a viable alternative for coherent optical OFDM to be considered in short distance transmissions. The simulation results also show that most of the developed wavelet mother functions mainly for image processing are not suitable for COOFDM transmission for its sensitivity to chromatic dispersion.     

色散控制光孤子系统性能分析

研究色散控制光孤子系统中的放大器的自发辐射噪声与交叉相位调制对孤子传输特性的影响，采用变分法分析了色散控制孤子的均方频移、定时抖动和误码特性，从降低自发辐射噪声和交叉相位调制扰动引起的均方频移出发，确定了补偿段的特性参量，给出了三种传输控制方案，分析了各方案中色散控制孤子的传输特性，其结果对色散控制孤子系统的设计具有参考价值。     

Simulation and analysis of dispersion compensation schemes for 100 Gbps PDM–OFDM optical communication system

In this paper, the implementation of 100 Gbps optical communication system exploiting polarization diversity at transmitter and receiver is developed and investigated with pre-, post- and symmetrical dispersion compensation schemes by using dispersion shifted and dispersion compensated fibers through simulations to optimize high data rate optical transmission. Motivation to the current analysis is to compare all 3 compensation schemes and it's found that the pre compensation technique is superior to post and symmetrical compensation techniques in 100 Gbps PDM–OFDM communication system. On examination of symmetrical and post dispersion compensation schemes, it's found that the later is superior to the previous in this case. A 100 Gbps coherent optical OFDM workplace has been discovered in which two 50 Gbps data streams are combined into one wavelength by polarization beam combiner. By comparing one can get a promising system to the symmetrical high capacity access network with high spectral efficiency, cost effective, good flexibility.     

A novel wavelength dispersive device with a dispersive element based on staircase-like straight and parallel arrayed waveguides

We propose a new type of arrayed waveguide grating (AWG) multiplexer/demultiplexer based on modified group refractive index. This device is composed by an array of straight and parallel waveguides of equal length and each waveguide consist of two sections with different width. The length of the two sections are changed from a waveguide to the adjacent one following a linear dependence resulting in a wavelength dispersive waveguide array. An example of the device design for silicon-on-insulator (SOI) platform is provided and numerical simulations have been carried out for various arrayed waveguide parameters. We demonstrate that the group index modification can be used for tailoring device dispersion properties, and that it can also result in new dispersion characteristics predicted numerically not observed in conventional AWGs. Additional advantages are that the demultiplexer does not necessarily require bending waveguide sections as in a conventional AWG (de)multiplexers, and thus yields highly compact devices with potentially very low insertion loss. Channel spacing of 1 nm have been predicted for sub-micron waveguides sizes. In this paper it is also proposed a novel wavefront converter based on waveguide array lens-like element with waveguides broadened sections. Numerical results for different input/output geometries are analized.     

偏振模色散及非线性效应对40 Gbit/s密集波分复用系统的影响

高速率、大容量的密集波分复用系统是光纤通信系统的最终发展方向 ,单信道速率达到 4 0Gbit/s时 ,光纤的非线性效应、偏振模色散现象对系统的影响更加突出。在综合考虑群速度色散、自相位调制、交叉相位调制、四波混合、偏振模色散等因素的基础上 ,推导了密集波分复用系统中任意信道的耦合非线性薛定谔方程组。利用扩展的分步傅里叶方法对该方程进行了数值计算 ,通过对 8× 4 0Gbit/s密集波分复用系统的仿真 ,分别研究了非线性效应和偏振模色散对密集波分复用系统的影响。发现由于交叉相位调制和四波混合作用 ,多波长的密集波分复用系统比单波系统受非线性效应影响严重 ;系统受偏振模色散与非线性效应的影响程度与输入信号功率有关 ,在入射光单信道平均功率较低 0 .1mW时 ,偏振模色散是影响系统性能的主要因素 ;当入射光单信道平均功率较高1mW时 ,系统受非线性效应影响严重。而偏振模色散在使信号脉冲展宽的同时 ,类似于非零色散位移光纤中的微小色散 ,对非线性效应又有一定的抑制作用。     

剩余三阶色散对相位共轭偏振孤子的影响及其补偿

光学相位共轭中剩余三阶色散不利于共轭孤子的稳定传输,导致孤子脉冲具有更大的时间抖动.本文提出在传输线末采用具有正三阶色散的色散位移光纤补偿光学相位共轭中的剩余正三阶色散.数值结果证明了其可行性.同时也分析其补偿的物理机制.     

Absolute polar duty cycle division multiplexing over wavelength division multiplexing system

The performance of absolute polar duty cycle division multiplexing (AP-DCDM) over wavelength division multiplexing (WDM) system is presented based on the simulation results. The AP-DCDM signal has narrower bandwidth than conventional time division multiplexing (TDM) signal, which makes its implementation in WDM system advantageous. In this paper, characteristics of AP-DCDM and TDM signals in WDM system are compared at the speed of 40 Gbit/s per channel, for the minimum allowed channel spacing and the chromatic dispersion tolerance. The results clearly show that AP-DCDM performs significantly better than TDM. By using AP-DCDM, 1.28 Tbit/s (32 × 40 Gbit/s) was successfully transmitted over 320 km standard single mode fiber. Spectral efficiency of 0.64 b/s/Hz was achieved by using 10 Gbit/s transmitters and receivers without polarization multiplexing.     

Dispersion-Managed Solitons in Multiple-Core Nonlinear Fiber Arrays

The variational principle is employed to obtain the evolution of the parameters of Gaussian and super-Gaussian chirped solitons that propagates through multiple-core nonlinear optical fiber arrays. This is governed by the dispersion-managed nonlinear Schrodinger's equation with strong dispersion management in the presence of linear coupling between the adjacent cores. The results are valid for any configuration of the cores.     

Crosstalk in double-pumped fiber optic parametric amplifiers for wavelength division multiplexing systems

We study experimentally inter-channel crosstalk in double-pumped fiber optic parametric amplifiers constructed with conventional dispersion shifted fibers (DSFs) having different lengths (L_A = 13.8, L_B = 6.8, L_C = 4.3, and L_D = 0.8 km). For long fibers (L_A and L_B), eye diagram measurements in a 5-channel (100 GHz spacing) system show that in order to have negligible crosstalk, the output signal power per channel, P_s, should be limited to P_s < 0 dBm. By decreasing the fiber length (to L_C) it is possible to increase the output signal power and/or the number of signals while keeping the crosstalk on negligible levels. This trend was further confirmed by using a very short DSF (L_D = 0.8 km).Finally, we experimentally demonstrate that a general trend in 2P-FOPAs is that spurious FWM increases with the number of signal channels up to a given number of channels when a saturation regime is reached. This saturation of the generation of spurious tones occurs when the bandwidth occupied by the signals exceeds ∼4-5 nm.     

Analysis of materials selected for multilayer diffractive optical elements

An analysis model to optimize the materials selected for multilayer diffractive elements (MLDOEs) is presented with approximate Cauchy dispersion formula of refractive index and the maximum polychromatic integral diffraction efficiency (PIDE). The analysis model presents that the maximum PIDE of MLDOEs consisting of two materials with large Abbe number difference and small partial dispersion difference can be generated. The scope of application and the relationship between diffraction efficiencies of MLDOEs with different material pairs and different design wavelength pairs are presented and simulated with the analysis model of MLDOEs.     

Cauchy's dispersion equation reconsidered: Dispersion in silicate glasses

We formulate a novel method of characterizing optically transparent substances using dispersion theory. The refractive index is given by a generalized Cauchy dispersion equation with coefficients that are moments of the uv and ir absorptions. Mean dispersion, Abbé number, and partial dispersion are combinations of these moments. The empirical relation between index and dispersion for families of glasses appears as a consequence of Beer's law applied to the uv spectra.     

Performance Analysis of Duty-Cycle Division Multiplexing over Wavelength Division Multiplexing System

Abstract

Performance optimization of a duty-cycle division multiplexing system over 8- and 40-channel wavelength division multiplexing networks is reported in this article. The modified duty-cycle division multiplexing system with optical domain multiplexing using a dual-drive Mach–Zehnder modulator is simulated with two and three users per wavelength. Using conventional dispersion compensation, the 40 × 40-Gbps system with two and three users per channel can support 240 and 160 km of transmission distance, respectively. The dispersion management technique based on a chirped fiber Bragg grating is proposed for a 40 × 3 × 13.33-Gbps duty-cycle division multiplexing/wavelength division multiplexing system that allows double the transmission distance compared to conventional technique.     

Cross-phase modulation in long-haul systems with chirped fiber Bragg gratings-based dispersion compensators

The cross-phase modulation (XPM) effect in fiber links with dispersion compensated by chirped fiber Bragg gratings (CFBGs) is analyzed here for the first time. A continuous-wave (CW) signal, referred to as a probe, is used to investigate the impact of XPM on communication systems. The result shows that the XPM in systems using CFBGs as dispersion compensators is greatly suppressed, compared with that of systems using dispersion compensated fiber (DCF). The difference of the dispersion management between the system using DCF and that using CFBGs is demonstrated, too.     

The Choice of Dispersion Managed Schemes in Standard Single-Mode Fiber

In this paper, the three allocated schemes of dispersion-managed soliton are proposed on standard single-mode fiber. Adopting variational method and on the proposed schemes, the timing jitter introduced from the perturbations of amplifier spontaneous-emission (ASE) and cross-phase modulation in wavelength-division multiplexing is studied. Compared with performances of different system schemes, the principles of optimal allocated dispersion management are obtained, which can be used to optimal allocated dispersion managed soliton system.     

Timing jitter induced by intrachannel interactions in optical fiber communication systems using CFG as dispersion compensator

In this paper, a theoretical model is proposed for the analysis of timing jitter induced by intrachannel interactions in optical fiber communication systems using chirped fiber grating (CFG) as dispersion compensator. And for the first time, the impact of group-delay ripple (GDR) on timing jitter is taken into account in detail, theoretically and numerically. Results show that the GDR may increase or decrease the timing jitter of certain pair of adjacent pulses, deciding by the ripple parameters. The maximum influence will be obtained when ripple period is about 2/5 of the input pulse width. In practical systems, the GDR enhance the timing jitter for some adjacent pulses while reduce it for some other adjacent pulses, depending on the pulse pattern and the GDR parameters. In our simulation, the GDR guarantees a 3.04 ps increase of the standard deviation of the timing jitter.     

Jacobi elliptic function solutions to (1 + 1) dimensional nonlinear Schrödinger equation in management system

A new kind of solutions namely elliptic function solutions to the (1 + 1) dimensional nonlinear Schrödinger equation (NLSE) in dispersion, nonlinearity and gain management system are obtained. The solutions are the generalization of analytical solutions to one-dimensional NLSE. The properties of the amplitudes and the phases of the solutions are investigated.