Lead-selective poly(vinyl chloride) membrane electrodes based on acyclic dibenzopolyether diamides

Lipophilic acyclic dibenzopolyether diamides, 12 kinds, have been designed to prepare solvent polymeric membrane ion-selective electrodes (ISEs) for Pb(2+). The ionophores include 1,5-bis[2-(N,N-dialkylcarbamoylmethoxy)phenoxy]-3-oxapentanes1-4, 1,5-bis[2-(N,N-dialkylcarbamoylpentadecyloxy)phenoxy]-3-oxapentanes 5-8, and 1,2-bis[2-(2'-N,N-dialkylcarbamoylpentadecyloxy)phenoxy]ethanes 9-12. Linear response concentration range of the ISE based on 9 is 3 x 10(-2) - 1 x 10(-6) M of Pb(2+) (average slope = 28.5 mV decade(-1)). Potentiometric selectivities of the ISEs based on 1-12 for Pb(2+) over other heavy metal cations, alkali metal cations, and alkaline earth metal cations have been assessed. These ISEs exhibit remarkably high selectivities for Pb(2+) relative to heavy metal cations, such as Cu(2+), Fe(2+), and Ni(2+), the selectivity coefficients (K(Pot)(Pb,Cu)) being 5 x 10(-5) - 6 x 10(-5) for 1-4 and ca. 6 x 10(-4) for 9. For the Pb(2+) selectivities over alkali metal cations, such as Na(+) and K(+), 9 which has an ethylene glycol spacer and a N,N-diethyl group is superior to other dibenzopolyether diamide ionophores 1-8 and 10-12.     

Measuring quaternary ammonium cleaning agents with ion selective electrodes

Data for coated-wire, ion selective electrodes (ISEs) are presented for cationic surfactant ions found in common cleaners including benzyldimethyltetradecylammonium, benzyldimethyldodecylammonium, and benzyldimethylhexadecylammonium. The ion exchangers dinonylnaphthalene sulfonic acid, tetraphenyborate, and tetrakis(4-chlorophenyl)borate are examined, showing dinonylnaphthalene sulfonic acid to be the favored species. The ISEs exhibit approximately Nernstian behavior down to the 10⁻⁶ M limit of detection with lifetimes in excess of 50 days when used continuously, and a shelf life of over 100 days. Reaching the upper detection limit at the critical micelle concentration requires use of polymeric-membrane reference electrodes including a new membrane cocktail, which allow response measurements of an order of magnitude higher than the traditional fritted-glass reference electrode. The surfactant ISEs show excellent selectivity over the common metal ions Na⁺, K⁺, Mg²⁺, Ca²⁺, and Cu²⁺ with selectivity coefficients less than 10^−5.3. The ISEs are also selective over the lower molecular weight quaternary ammonium ions tetradecyltrimethylammonium, dodecyltrimethylammonium, benzyldimethyl(2-hydroxyethyl)ammonium, and tetrabutylammonium with selectivity coefficients ranging from 10^−1.7 to 10^−5.5. Use of a single electrode to determine accurately the total cationic surfactant concentration in common cleaning solutions is accomplished with information about concentration dependent interferences and a modified Nikolsky–Eisenman model. Finally, quaternary ammonium surfactants have a deleterious effect on the measurements of pH and common ions like K⁺, Mg²⁺ and Ca²⁺ with polymeric ISEs. This makes it critical to include surfactant electrodes in a detector array when cleaning agents are present.     

Mercury(II) ion-selective electrodes based on heterocyclic systems

Mercury ion-selective electrodes (ISEs) were prepared with a polymeric membrane based on heterocyclic systems: 2-methylsulfanyl-4-(4-nitro-phenyl)-l-p-tolyl-1H-imidazole (I) and 2,4-diphenyl-l-p-tolyl-1H-imidazole (II) as the ionophores. Several ISEs were conditioned and tested for the selection of common ions. The electrodes based on these ionophores showed a good potentiometric response for Hg2+ ions over a wide concentration range of 5.0 x 10(5-) - 1.0 x 10(-1)M with near-Nernstian slopes. Stable potentiometric signals were obtained within a short time period of 20 s. The detection limits, the working pH range of the electrodes were 1.0 x 10(-5) M and 1.6-4.4 respectively. The electrodes showed better selectivity for Hg2+ ions over many of the alkali, alkaline-earth and heavy metal ions. Also sharp end points were obtained when these sensors were used as indicator electrodes for the potentiometric titration of Hg2+ ions with iodide ions.     

Modern potentiometry

For most chemists, potentiometry with ion-selective electrodes (ISEs) primarily means pH measurements with a glass electrode. Those interested in clinical analysis might know that ISEs, routinely used for the determination of blood electrolytes, have a market size comparable to that of glass electrodes. It is even less well known that potentiometry went through a silent revolution during the past decade. The lower detection limit and the discrimination of interfering ions (the selectivity coefficients) have been improved in many cases by factors up to 10(6) and 10(10), respectively, thus allowing their application in fields such as environmental trace analysis and potentiometric biosensing. The determination of complex formation constants for lipophilic hosts and ionic guests is also covered in this Minireview.     

Lipophilic ionic additive for controlling the selectivity of ion-selective electrodes reversible to cations of nitrogen-containing organic bases

The effect of a lipophilic ionic additive, a tetradecylammonium salt of a liquid ion exchanger, on the selectivity of ion-selective electrodes (ISEs) for cations of nitrogen-containing organic bases was studied. Additive-containing ISEs exhibited a higher selectivity for cations of primary to tertiary amines as compared to that for quaternary ammonium cations. A maximum change in selectivity (up to more than two orders of magnitude) due to the introduction of tetradecylammonium was observed for membranes containing dinonyladipate as a plasticizer and tris(nonyloxy)benzene sulfonic acid as an ion exchanger. In this case, the introduction of lipophilic ionic additive may lead to the reversal of the selectivity series. The effect of the lipophilic ionic additive on the selectivity of ISEs with membranes plasticized with o-nitrophenyl octyl ether decreased approximately by an order of magnitude. The selectivity of ISEs with the membranes containing tetrakis(4-chlorophenyl) borate as a cation exchanger was virtually independent of the presence of lipophilic ionic additives. The results obtained were explained by the peculiarities of ion-pair formation in the membrane.     

Potentiometric sensors based on fluorous membranes doped with highly selective ionophores for carbonate

Manganese(III) complexes of three fluorophilic salen derivatives were used to prepare ion-selective electrodes (ISEs) with ionophore-doped fluorous sensing membranes. Because of their extremely low polarity and polarizability, fluorous media are not only chemically very inert but also solvate potentially interfering ions poorly, resulting in a much improved discrimination of such ions. Indeed, the new ISEs exhibited selectivities for CO(3)(2-) that exceed those of previously reported ISEs based on nonfluorous membranes by several orders of magnitude. In particular, the interference from chloride and salicylate was reduced by 2 and 6 orders of magnitude, respectively. To achieve this, the selectivities of these ISEs were fine-tuned by addition of noncoordinating hydrophobic ions (i.e., ionic sites) into the sensing membranes. Stability constants of the anion-ionophore complexes were determined from the dependence of the potentiometric selectivities on the charge sign of the ionic sites and the molar ratio of ionic sites and the ionophore. For this purpose, a previously introduced fluorophilic tetraphenylborate and a novel fluorophilic cation with a bis(triphenylphosphoranylidene)ammonium group, (R(f6)(CH(2))(3))(3)PN(+)P(R(f6)(CH(2))(3))(3), were utilized (where R(f6) is C(6)F(13)). The optimum CO(3)(2-) selectivities were found for sensing membranes composed of anionic sites and ionophore in a 1:4 molar ratio, which results in the formation of 2:1 complexes with CO(3)(2-) with stability constants up to 4.1 × 10(15). As predicted by established theory, the site-to-ionophore ratios that provide optimum potentiometric selectivity depend on the stoichiometries of the complexes of both the primary and the interfering ions. However, the ionophores used in this study give examples of charges and stoichiometries previously neither explicitly predicted by theory nor shown by experiment. The exceptional selectivity of fluorous membranes doped with these carbonate ionophores suggests their use not only for potentiometric sensing but also for other types of sensors, such as the selective separation of carbonate from other anions and the sequestration of carbon dioxide.     

Solid-contact ion-selective electrodes for aromatic cations based on pi-coordinating soft carriers

Ion-selective electrodes (ISEs) based on pi-coordinating carriers were prepared and investigated as potentiometric sensors for aromatic cations, using N-methylpyridinium as a model aromatic cation. Derivatives of tetraphenylborate were studied as charged carriers in plasticized poly(vinyl chloride) membranes. Furthermore, neutral compounds containing pi-coordinating anthryl groups were studied as neutral carriers. Bis(2-ethylhexyl)sebacate (DOS) and 2-nitrophenyl octyl ether (o-NPOE) were used as non-polar and polar plasticizer, respectively. ISEs were constructed by using poly(3,4-ethylenedioxythiophene) (PEDOT) as solid-contact material. Conventional ISEs with internal filling solution were used for comparison. The potentiometric responses of the ISEs were investigated using N-methylpyridinium as primary ion. The results show that the selectivity of the ISEs is influenced significantly by both the plasticizer and the charged carriers, while the neutral carriers studied have only a minor influence on the selectivity. The role of cation-pi interactions between aromatic cations and the membrane components is discussed.     

New sensing materials of molecularly-imprinted polymers for the selective recognition of Chlortetracycline

As a result of the stressful conditions in aquaculture facilities there is a high risk of bacterial infections among cultured fish. Chlortetracycline (CTC) is one of the antimicrobials used to solve this problem. It is a broad spectrum antibacterial active against a wide range of Gram-positive and Gram-negative bacteria. Numerous analytical methods for screening, identifying, and quantifying CTC in animal products have been developed over the years. An alternative and advantageous method should rely on expeditious and efficient procedures providing highly specific and sensitive measurements in food samples. Ion-selective electrodes (ISEs) could meet these criteria. The only ISE reported in literature for this purpose used traditional electro-active materials. A selectivity enhancement could however be achieved after improving the analyte recognition by molecularly imprinted polymers (MIPs).Several MIP particles were synthesized and used as electro-active materials. ISEs based in methacrylic acid monomers showed the best analytical performance according to slope (62.5 and 68.6 mV/decade) and detection limit (4.1 × 10⁻⁵ and 5.5 × 10⁻⁵ mol L⁻¹). The electrodes displayed good selectivity. The ISEs are not affected by pH changes ranging from 2.5 to 13. The sensors were successfully applied to the analysis of serum, urine and fish samples.     

Synthesis of a tweezer-like bis(arylthiaalkoxy)calix[4]arene as a cation sensor for ion-selective electrodes: an investigation of the influence of neighboring halogen atoms on cation selectivity

Two novel tweezer-like 25,27-dihydroxy-26,28-bis(phenylthiaethoxy)calix[4]arenes 6 and 7 were synthesized by the reaction of 25,27-dihydroxy-26,28-bis(bromoethoxy)calix[4]arenes 3 and 4 for the evaluation of their ion-selectivity in ion-selective electrodes (ISEs). X-ray structural analysis indicated that calix[4]arene 7 is in an interesting infinite linear aggregate via self-inclusion. For investigation of the influences of substitutes on the behavior of the ISEs, the halogen substituted aryl analogues of 25,27-dihydroxy-26,28-bis(arylthiaethoxy)calix[4]arenes 8-12 were also synthesized and their ISE performances were evaluated under the same conditions. ISEs based on 6-12 as neutral ionophores were prepared, and their selectivity coefficients for Ag+ (log KAg,M(pot)) were investigated against other alkali metal, alkaline-earth metal, lead, ammonium ions and some transition metal ions using the fixed interference method (FIM). These ISEs showed excellent Ag+ selectivity over most of the interfering cations examined, except for Hg2+ having relative smaller interference (log KAg,Hg(pot) < or = 2.1). The 19F NMR spectra of 9 and 9.AgClO4 were recorded for investigation the fluorine environments in the complex. The 19F NMR spectra strongly suggested that the fluorine atoms on ionophore 9 participated in ligation with silver cation.     

Cesium-ion selective electrodes based on calix[4]arene dibenzocrown ethers

Four calix[4]arene dibenzocrown ether compounds have been prepared and evaluated as Cs(+)-selective ligands in solvent polymeric membrane electrodes. The ionophores include 25,27-bis(1-propyloxy)calix[4]arene dibenzocrown-6 1, 25,27-bis(1-alkyloxy)calix[4]arene dibenzocrown-7s 2 and 3, and 25,27-bis(1-propyloxy)calix[4]arene dibenzocrown-8 4. For an ion-selective electrode (ISE) based on 1, the linear response concentration range is 1x10(-1) to 1x10(-6) M of Cs(+). Potentiometric selectivities of ISEs based on 1-4 for Cs(+) over other alkali metal cations, alkaline earth metal cations, and NH(4)(+) have been assessed. For 1-ISE, a remarkably high Cs(+)/Na(+) selectivity was observed, the selectivity coefficient (K(Cs,Na)(Pot)) being ca. 10(-5). As the size of crown ether ring is enlarged from crown-6 (1) to crown-7 (2 and 3) to crown-8 (4), the Cs(+) selectivity over other alkali metal cations, such as Na(+) and K(+), is reduced successively. Effects of membrane composition and pH in the aqueous solution upon the electrode properties are also discussed.     

Optimization of the Composition of Ca-Selective Membranes Based on Tridentate Phosphoryl-Containing Neutral Ionophores

The selectivity and sensitivity of ion-selective electrodes (ISEs) based on membranes with phosphoryl-containing ionophores and lipophilic anion exchangers were studied. The analytical properties of the ISEs can be significantly modified and their selectivity for alkali and alkaline-earth metals can be even reversed by changing the membrane composition.     

用交流阻抗法研究某些离子选择电极的响应特性

用交流阻抗法研究了两种液膜胆R汁酸电极和两种聚氯乙烯(PVC)膜钙离子选择电极. 从体电阻R_b和电荷传递电阻R_(ct)得到膜内离子迁移活化能E_a, 及电极的表观标准交换电流密度i°_0等信息. 结果表明: E_a比R_b更能反映离子在膜内迁移的情况, 离子在PVC膜中的迁移比在液膜中困难得多; i°_0能在一定程度上反映电极性能的优劣等。     

4'-picrylamino-5'-nitrobenzo-18-crown-6 as a sensing reagent in potassium ion-selective electrode membranes

Five crown ethers, namely, 4'-picrylamino-5'-nitrobenzo-18-crown-6 (I), dibenzo-18-crown-6 (III), dibenzo-30-crown-10 (IV), dicyclohexano-18-crown-6 (V) and bis-[(benzo-15-crown-5)-15-ylmethyl pimelate] (VI) have been compared with valinomycin (II) for their role as potassium ion-sensors in PVC matrix membrane ion-selective electrodes (ISEs). Sensor I was found to be the best, but fell short of the high quality of the well established sensor II (valinomycin) in terms of selectivity towards potassium over sodium and ammonium. Nevertheless, electrodes made from membranes containing sensor I, 2-nitrophenyl octyl ether (NPOE) or 2-nitrophenyl phenyl ether and potassium tetra-p-chloro-phenylborate (anion excluder) in PVC were of long lifetimes. The loss of slope of the ISEs is linked to small falls in the electrical resistance of the ISE membranes; this being associated with leaching of sensor and solvent mediator from the membranes into test or storage solutions. No chromatographic evidence was found of anion excluder being leached.     

The effect of the ion exchanger site-counterion complex formation on the selectivities of ISEs

Using the model of ideally associated solution, the effect of ion association of the ion exchanger sites with main and foreign counterions on the selectivity of ISEs based on liquid ion exchangers has been considered. Equations which describe the potentiometric selectivity coefficient as a function of ion association constants in the membrane phase and of standard free energies of transfer of the determined and foreign ions from water to the membrane are obtained for the following main cases: (a) the determined and foreign ions are single-charged; (b) the determined ion is double-charged and the foreign ion is single-charged. It is shown that in the case of single-charged main and foreign ions, the ratio of the ion association constants has a great effect on the potentiometric selectivity of membranes, only if the ion exchanger sites produce less strong associates with the determined counterion as compared with the foreign one. Otherwise, this effect is insignificant. The selectivity for double-charged ions should increase, other things being equal, as the first constant of association of these ions with the ion exchanger sites increases. The effect of producing ion triplets of the type I(2)R((+/-)) on the selectivity of ISEs is also considered. Experimental data are presented which illustrate the effect of the nature of the ion exchanger on the potentiometric selectivity. Some procedures employing the factor of ion association for increasing the potentiometric selectivity of liquid ion exchange membranes are considered.     

Ion-selective electrodes for determination of organic ammonium ions: Ways for selectivity control

The influence of the ISE membrane composition on the selectivity for primary, secondary, tertiary, and quaternary alkylammonium cations, as well as for cations of physiologically active amines, has been investigated. Factors studied include the effect of plasticizer (2-nitrophenyl octyl ether, o-NPOE; dibutyl phthalate, DBP; dinonyl adipate, DNA; tris(2-ethylhexyl) phosphate, TEHP) and ion exchanger (potassium tetrakis(4-chlorophenyl)borate, K(TpClPB); potassium tris(nonyloxy)benzenesulfonate, K(TNOBS)), as well as that of the lipophilic cationic additive (tetradecylammonium nitrate, (TDA)NO(3)) and neutral carrier (dibenzo-18-crown-6) presence in membrane. It has been established that plasticizer nature affects K(i,j)(pot) values both when the target and/or foreign ions have non-ionic polar groups capable of specific interaction with plasticizer, and when the only difference consists in the substitution degree of their ionic groups. K(i,j)(pot) values for quaternary alkylammonium cations over primary-tertiary ones change in the following order: TEHP>DBP approximately DNA>o-NPOE. The highest K(i,j)(pot) value change is achieved for the primary-quaternary alkylammonium cation pair, amounting to 3 and 4.7 orders for membranes containing K(TNOBS) and K(TpClPB) as ion exchangers, respectively. In its turn, the ion exchanger influence on the selectivity depends on plasticizer nature, it being maximal for o-NPOE (about 2 orders) and practically non-existent for TEHP. On the whole, as compared to K(TpClPB)-based ISEs, those based on K(TNOBS) show higher selectivity for primary-tertiary alkylammonium cations over quaternary ones. Incorporation of (TDA)NO(3) into membrane causes further improvement of selectivity for primary-tertiary alkylammonium cations in the case of K(TNOBS) only. The maximal total effect of the ion exchanger and lipophilic ionic additive is observed for ISEs with DNA-plasticized membranes and is over 3 orders. The influence of crown ether on the selectivity also depends significantly upon ion exchanger and plasticizer nature. For ISEs with o-NPOE-plasticized membranes the K(i,j)(pot) value changes can be as great as 3 (ion exchanger K(TNOBS)) and even 4.5 (ion exchanger K(TpClPB)) orders. On the contrary, for ISEs with TEHP-plasticized membranes the crown ether effect on the selectivity is unessential. The results obtained are explained by peculiarities of organic ammonium cations solvating by plasticizer and association of cations with ion exchangers.     

A Method of Determining Selectivity Coefficients Based on the Practical Slope of Ion Selective Electrodes

It is a problem to be solved that the experimental selectivity coefficients of ion selective electrodes( ISEs) depend on the activity. This paper studied the new method of determining selectivity coefficients. A mixed ion response equation, which was similar to Nicolsky-Eisenman (N-E) equation recommended by IUPAC, was proposed. The equation includes the practical response slope of ISEs to the primary ion and the interfering ion. The selectivity coefficient was defined by the equation instead of the N-E equation. The experimental part of the method is similar to that based on the N-E equation. The values of selectivity coefficients obtained with this method do not depend on the activity whether the electrodes exhibit the Nernst response or non-Nernst response. The feasibility of the new method is illustrated experimentally.     

Potentiometric Determination of Non‐Ionic Surfactants by Liquid Membrane Electrodes

It is well known that non‐ionic surfactants (NIS) influence remarkably the potentiometric measurements with liquid membrane ion selective electrodes (ISEs), interfering particularly on performance of ISEs for earth‐alkali metals, for which the loss of selectivity with regard to alkali metals has been documented. These studies indicate that such interferences are due to the extraction of surfactants within the membrane, where a competition takes place between the originally present ionophore and the surfactant which also acts as a ligand for alkali metals. The interpretation of such phenomena enabled one to exploit this interference for analytical purposes by membrane/solution extraction experiment monitored by UV measurements and by impedance FRA analysis on coated wire electrodes. Using Ca/Mg ISEs based on the neutral ionophore ETH 4030, it has been established that the logarithm of the Ca/Mg over Na potentiometric selectivity constant is linearly correlated with the concentration of NIS like Tegopren 5863 and Triton X‐100. The proposed method has been applied for the development of a new potentiometric analytical procedure for the determination of Tegopren 5863 in synthetic seawater (SSW), ranging from 0.25 to 5 ppm. Our procedure consists in the exposure of the electrode to stirred SSW containing the surfactant; the progressive extraction of Tegopren 5863 causes a growth in electrode's sensitivity to Na⁺ and K⁺, losing selectivity for Ca²⁺ and Mg²⁺. In turn this induces an increase of EMF, as all these ions are present in the studied matrix. The potential drift was monitored for 15 hours, showing that the process reaches thermodynamic equilibrium after about 12 hours of exposure. This method presents a value of 210 ppb of Tegopren 5863 as detection limit.     

Cobalt(II) porphyrazine as an active component of iodide-selective electrodes

Cobalt(II) porphyrazine is synthesized and studied as an active component of a polyvinyl chloride plasticized membrane ion-selective electrodes (ISEs). It is established that regardless of their structure, ISEs are sensitive to iodide. The introduction to the ISE of an ionic additive, ionic liquid 1,3-dihexadecylimidazolium chloride, significantly improves the electrochemical characteristics: the slope of the electrode function reaches ?(57 ± 1) mV/dec, c_min = 8.3 × 10^–6 M. Solid-state screen-printed electrodes the surfaces of which are modified by a 1: 4 mixture of cobalt(II) porphyrazine and ionic liquid 1,3-dihexadecylimidazolium chloride demonstrate satisfactory electrochemical characteristics: the slope of the electrode function is ?(56 ± 4) mV/dec and c_min = 2.5 × 10^–5 M. The potentiometric selectivity of the ISEs for iodide is studied. It is found that the effect of lipophilic interfering ions is significantly lower for solid state ISEs than for plasticized membrane electrodes.     

Micro Solid‐Contact Ion‐Selective Electrode Using a Carbon Nanotube Tower as Ion‐to‐Electron Transducer and Conductive Substrate

Solid contact (SC) ion‐selective electrodes (ISEs) have been recognized as the next generation of ISEs. In this work, the electrical conductivity and mechanical strength of a carbon nanotube (CNT) tower enable it to play the dual roles of transducer and substrate for micro SC‐ISEs. The electrode had a close to Nernstian slope of 35 mV/decade a_Ca2+, a linear range of four orders of magnitude of calcium ion activity (10^?5.6 to 10^?1.8 M), and a detection limit of 1.6×10^?6 M. The simplified fabrication by a one‐step drop casting makes miniaturizing SC‐ISEs and fabricating sensor arrays easier to achieve.     

All-solid-state Fluoride Ion-selective Electrode using LaF3 Single Crystal with Poly(3,4-ethylenedioxythiophene) as Solid Contact Layer

An all-solid-state fluoride ion-selective electrode (ISE) was prepared using LaF₃ single crystal with poly(3,4-ethylenedioxythiophene (PEDOT) as the solid contact layer. In contrast to polymer-based ISEs, crystalline membrane-based ISEs have not been used for all-solid-state device, thereby prohibiting the integration of ISEs on a chip. The all-solid-state fluoride ISE developed in this study exhibited superior sensitivity (−56.0±0.9 mV/dec) and selectivity compared to those of conventional inner filling solution ISE. The effects of PEDOT as a solid contact layer were analyzed using chronopotentiometry and electrochemical impedance spectroscopy, which revealed that PEDOT promoted electrode stability. The all-solid-state device can miniaturize the fluoride ISE and facilitate environmental, industrial, agricultural, and physiological monitoring.