原子荧光光谱仪的便携化设计

针对重金属污染现场快速检测领域的发展需求,成功开发首台便携式原子荧光光谱仪。实现了高度集成低功耗进样系统、微型低功耗原子化系统、数字化对光技术、微型光电检测系统以及无线通讯技术等十余项关键技术的重大突破。整机功率仅为12 W,重量仅为10kg,锂电池供电状态下工作时间不小于8h,具备与实验室常规原子荧光光谱仪相同的性能指标,可直接用于砷、汞、铅、镉等重金属的野外现场快速检测。     

直接进样钨丝电热蒸发-原子荧光光谱法快速测定蒸馏酒中镉

为了快速低成本测定蒸馏酒中痕量重金属镉,利用钨丝电热蒸发器作为直接进样装置,与原子荧光光谱仪原子化器直接连接,构建了用于蒸馏酒中镉测定的直接进样原子荧光光谱检测系统(W-coil ETV-AFS),并对工作气体的气氛和流速、灰化和蒸发电压、样品承载量等参数进行了优化,建立了蒸馏酒中镉的直接进样快速检测方法.在最优条件下...     

直接进样电热蒸发-原子荧光光谱法快速测定蒸馏酒中镉

为了快速低成本测定蒸馏酒中痕量重金属镉,利用钨丝电热蒸发器作为直接进样装置,与原子荧光光谱仪原子化器直接连接,构建了用于蒸馏酒中镉测定的直接进样原子荧光光谱检测系统(W-coil ETV-AFS),并对工作气体的气氛和流速、灰化和蒸发电压、样品承载量等参数进行了优化,建立了蒸馏酒中镉的直接进样快速检测方法。在最优条件下,Cd的检出限(LOD)为0.06μg/L(进样量为50μL),在0.5~100μg/L线性范围内回归系数(R²)为0.997;在5μg/L水平下,9个典型蒸馏酒样品的加标回收率在86.0%~116%,相对标准偏差RSD≤8.0%(n=3)。可以直接导入样品,无需复杂的前处理过程,具有良好的灵敏度、准确度和精密度,非常适合蒸馏酒中痕量镉的快速测定。     

低温等离子体原子荧光光谱法直接测定固体样品中的汞

建立了低温等离子体(LTP)与原子荧光光谱仪(AFS)联用直接检测ABS固体样品中Hg的方法.实验采用介质阻挡放电(DBD)方式产生低温等离子体,剥蚀固体样品后产生的元素蒸气引入到原子荧光光谱仪进行检测.优化的实验条件为:DBD外接电源的放电功率为16～18 W,放电气体流速为400 mL/min;采样距离为1～5 mm;原子荧光光谱仪的原子化器高度为10 mm.本系统测定Hg的检出限为0.91 mg/kg,线性范围为91.5～1096 mg/kg;精密度(RSD,n=7)为1.9％～2.3％,并对标准样品以及实际样品进行测定,测定结果与标准值与ICPMS及CVG-AFS一致,表明本方法可作为直接检测固体样品的新型元素分析技术.     

电沉积-钨丝电热原子吸收光谱法测定地质样品中痕量金

以市售幻灯投仪卤钨灯泡钨丝为原子化器的钨丝电热原子吸收光谱分析仪(TC-AAS),功率小、仪器成本低[1,2],如用微型CCD光谱仪作检测系统,可以实现原子吸收光谱仪的小型化,甚至可用于野外现场分析[3,4].     

直接测汞仪与原子荧光法测定海洋底栖生物中痕量汞的对比研究

使用直接测汞仪和原子荧光光谱仪对海洋底栖生物脉红螺中痕量汞的测定进行了方法对比研究,实验结果表明:直接测汞仪在0~20.0ng和20.0~1 400.0ng范围内均呈良好的二次非线性拟合(R2=1.0000),原子荧光光谱仪在0.025~0.800μg/L范围内呈良好的线性关系(R2=0.9993)。在取样量相同的情况下,直接测汞仪的方法检出限为9.0×10-4μg/g,优于原子荧光光谱仪的3.9×10-3μg/g。采用国际标准物质贻贝组织(NIST SRM 2976)对比了方法的准确度和精密度,结果表明:直接测汞仪的回收率为97.95%,RSD为1.77%,原子荧光光谱仪的回收率为96.68%,RSD为3.99%。直接测汞仪简便快速,重现性好,准确度高,可用于海洋底栖生物中痕量汞的检测。     

便携式激光诱导击穿光谱仪测定土壤中重金属

土壤重金属污染对农作物生长和人体健康都有严重危害,现场快速检测对土壤重金属污染调查、应急监测具有重要意义。采用自主研发的土壤重金属激光诱导击穿光谱现场快速检测仪对矿区周边土壤进行现场检测分析,以835个不同基质土壤的光谱数据建立定标数据库,通过支持向量机建立回归模型对土壤重金属元素含量进行定量反演。现场检测获取的全波段光谱波动在15%以内,Cd、Cr、Cu、Ni、Pb和Zn等6种元素光谱强度相对标准偏差平均值为6.31%。将检测结果与实验室电感耦合等离子体质谱法分析对比,6种元素的皮尔逊相关系数r在0.850 1～0.982 9,检测结果80%以上处于±30%相对误差区间分布。对比结果表明自主研发的土壤重金属激光诱导击穿光谱现场检测仪可以满足现场快速检测需求。     

快速检测三聚氰胺激光仪问世

中国检验检疫科学研究院2月28日宣布,该院利用激光拉曼技术,自主研发了用于现场快速检测三聚氰胺的激光拉曼光谱仪以及配套试剂。使用该仪器和配套试剂,能定量检测出液态奶中高于5×10-7(0.5ppm)的三聚氰胺,每个样品检测仅需半分钟。中国检科院首席专家、研究员邹明强说,牛奶不同于其它食品,原料奶的保质期为4h,如果奶农把原料奶送到实验室来检测三聚氰胺等物质,时间长了牛奶很容易变坏,因此需要研发小型、低成本、准确的现场快速检测设备。中国检科院结合纳米和激光技术,利用激光拉曼仪,成功开发了现场快速检测液态奶中三聚氰胺含量的技术以及配套增敏试剂,可使传统的拉曼检测灵敏度大幅提高,克服了样品基质干扰,真正实现了快速、准确地分析实验样品中的三聚氰胺。据悉,目前报道的国外同类技术对牛奶样品检测,加上样品处理,共需要50min,且不能达到对三聚氰胺的定量检测。(仪器信息网)快速检测三聚氰胺激光仪问世     

测定土壤中重金属元素时前处理方法的改进

建立了一种微波消解前处理技术的半消解法消解样品,采用原子吸收光谱法和原子荧光光谱法同时测定土壤中主要重金属元素铜、锌、镉、砷、汞的方法,检测土壤标准物质GSS-3、GSS-5、GSS-20,结果显示测定均值在标准差允许范围内,相对标准偏差小于8.5%(n=4),是土壤重金属元素快速检测的可选方法。     

测定土壤中重金属元素时前处理方法的改进

建立了一种微波消解前处理技术的半消解法消解样品,采用原子吸收光谱法和原子荧光光谱法同时测定土壤中主要重金属元素铜、锌、镉、砷、汞的方法,检测土壤标准物质GSS-3、GSS-5、GSS-20,结果显示测定均值在标准差允许范围内,相对标准偏差小于8.5%(n=4),是土壤重金属元素快速检测的可选方法。     

Tungsten coil devices in atomic spectrometry: absorption, fluorescence, and emission.

In this work, tungsten coil (W-Coil) devices are used as atomizers for electrothermal atomization atomic absorption spectrometry (ETAAS), electrothermal atomization laser excited atomic fluorescence spectrometry (ETA-LEAFS), and electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES). For most cases in ETAAS and ETA-LEAFS, limits of detection (LODs) using the W-Coil are within a factor of ten of those observed with commercial graphite furnace systems. LOD for Cd by W-Coil AAS is 10 pg, while LODs for As, Se, Cr, Sb and Pb by W-Coil LEAFS are 950, 320, 1400, 330, and 160 fg, respectively. The compact W-Coil device makes it an ideal atomizer for portable atomic spectrometry instrumentation, especially when coupled with a miniature charge coupled device spectrometer. Alternatively, the atomizer can be used as an inexpensive, modular add-on to an existing commercial ICP-AES system; and the thermal separation of Pb with interference elements Al, Mn, and Fe is demonstrated.     

Sub-miniature ExB sector-field mass spectrometer

A novel sub-miniature double-focusing sector-field mass spectrometer has been fabricated at the University of Minnesota using a combination of conventional machining methods and thin film patterning techniques typically used in the sensor technology industry. Its design is based on the mass separation capabilities of a 90 degrees cylindrical crossed electric and magnetic sector-field analyzer with a 2-cm radius, which under proper conditions is able to effectively cancel the angular and chromatic dispersion of the ion beam, thus improving the resolving power of the instrument. Simulations using finite element analysis and computer modeling were employed to verify and optimize the performance of the proposed instrument before and during its fabrication. The prototype was able to attain a resolving power of 106 full-width at half-maximum (FWHM), a detection limit close to 10 parts per million, a dynamic range of 5 orders of magnitude and a mass range up to 103 Da. Its overall size, including the magnet assembly, is 3.5 cm wide, 6 cm long and 7.5 cm tall, it weighs 0.8 kg, and its power consumption was measured to be 2.5 W. The performance of the instrument was found to be comparable to that of commercial residual gas analyzers, at a fraction of the cost. All these characteristics make this miniature mass spectrometer suitable for portable and low-cost analytical instrumentation.     

原位电离与小型质谱在公共安全领域的应用

质谱作为一种具有高准确度、高灵敏度、高选择性的检测仪器,在公共安全领域有着重要的应用前景.公共安全领域的需求主要涉及毒品、毒物、爆炸物等化学物质的现场快速检测,因其影响广泛,检测结果需非常准确.作为实验室分析仪器,质谱的准确性和速度能满足公共安全的应用需求,但作为现场快速检测的仪器仍需要一定改进.现场快速检测一方面要求...     

Atomic fluorescence and atomic emission measurements with an image dissector echelle spectrometer

This paper deals with the investigation of an image dissector echelle spectrometer as an analytical instrument for flame atomic fluorescence spectrometry and for flame atomic emission spectroscopy. The fluorescence was induced by high-pressure xenon arc lamps, which emitted continuum spectra and had higher power ratings, i.e. 1.6 and 2.5 kW, than those normally used for the same purpose. The experimental set-up included two different types of premix burners and one type of total consumption burner. A spherical reflector was applied to improve the utilization of the fluorescence radiation. Two different coatings were tested. None gave the expected enhancement.Detection limits and growth curves were measured for 8 different elements (Ca, Co, Cu, Fe, K, Mg, Na and Ni) in a non-separated air/acetylene flame. The attained detection limits were found to be equally good or somewhat better in flame atomic fluorescence excited with continuum sources than previously reported in the literature, i.e. using similar flames. In flame atomic emission spectroscopy better detection limits have been reported before.     

Evaluation of Improved Ultrasonic Nebulizer for Miniature Simultaneous Microwave Plasma Torch Spectrometer

Introduction Forthelaboratoriesthatrequirerapidresultsor havehighsamplethroughput,analysisspeedispara mount.Tomeetthisrequirement,thedevelopmentof atomicspectrometershasgonethroughmanystages,fromsinglechannelsequentialscanningspectrometers,multichanneldir…     

Quantification and evaluation of ion transmission efficiency in two-stage vacuum chamber miniature mass spectrometer

Miniature mass spectrometer is more compact and portable than traditional commercial mass spectrometry, with more potential for application outside the laboratory. However, a miniature mass spectrometer is less sensitive than a commercial instrument, limiting its application scenarios. The ion transmission efficiency of the instrument is an essential factor affecting the sensitivity. Still, there are few works of literature on the quantitative study of the ion transmission efficiency of each component from a systematic perspective. In this paper, the Faraday cup coupled with a microcurrent signal testing instrument was used to measure the ions generated by nanoelectrospray ionization (nano-ESI), which have successfully gone through several components. Then the ion transmission efficiency of each component was quantified. Results showed that the front lens had the highest ion transmission efficiency of 39.7%, whereas the inlet and skimmer had the lowest ion transfer efficiency of 0.8% and 17.1%. Next, the influence of control parameters on ion transmission efficiency of critical components was investigated. If optimized, the ion funnel and the skimmer had the potential to improve their transmission efficiency by 120% and 79%, respectively. This paper shows the decreasing intensity distribution of ions in the whole transmission process and the transmission efficiency of each component, which can guide for improving the sensitivity of the miniature mass spectrometer.     

Ion/molecule reactions in a miniature RIT mass spectrometer

Ion/molecule reactions were explored in a newly developed miniature mass spectrometer fitted with a rectilinear ion trap (RIT) mass analyzer. The tandem mass spectrometry performance of this instrument is demonstrated using collision induced dissociation (CID) and ion/molecule reactions. The latter includes Eberlin transacetalization reactions and electrophilic additions. Selective detection of the chemical warfare simulant dimethyl methyl phosphonate (DMMP) was achieved through selective Eberlin reactions of its characteristic phosphonium fragment ion CH3OP(+)(O)CH3 (m/z 93), with 1,4-dioxane or 1,3-dioxolane. Efficient adduct formation as a result of electrophilic attack by the phosphonium ion on various nucleophilic reagents, including 1,1,3,3-tetramethyl urea, methanesulfonic acid methyl ester, dimethyl sulfoxide and methyl salicylate, was also observed using the RIT device. The product ions of these reactions were analyzed using CID and the characteristic fragmentation patterns of the ionic addition products were recorded using multiple-stage experiments in the miniature RIT instrument. This study clearly demonstrates that a small, home-built, miniature RIT mass spectrometer can be used to perform analytically useful ion/molecule reactions and also that instruments like this have the potential to provide a portable platform for in situ detection of organophosphorus esters and related compounds with high specificity using tandem mass spectrometry.     

电沉积-钨丝电热原子吸收光谱法测定水样中的铅

研制了一种便携式钨丝电热原子吸收光谱分析装置,其主要包括:钨丝电热原子化器、多道微型CCD光谱仪、仪器电源系统以及控制系统。并将电沉积分离富集技术与该钨丝电热原子吸收光谱分析仪器结合,完成环境水样中铅的现场分析。并对铅的电沉积条件作了研究,最佳电沉积电位为负650 mV(vs.SCE),方法检出限:0.20μg/L,线性范围:1~15μg/L,对4μg/L Pb标准溶液10次重复测试,RSD为4.4%。     

液相色谱–原子荧光联用仪的校准

介绍液相色谱–原子荧光联用仪的校准方法。液相色谱–原子荧光联用仪的校准主要包括仪器的基线噪声漂移、测量线性、测量重复性和检出限等项目。通过分析实验数据,当仪器基线噪声不大于5 m V,基线漂移不大于50 m V/(30 min),保留时间重复性不大于3%,峰面积重复性不大于5%,仪器测量线性r大于0.995,检出限不高于4 ng/m L时,仪器的计量性能指标正常。据此对影响仪器性能的各个参数进行全面评价,确认各项性能指标控制在合理范围内,以保证液相色谱–原子荧光联用仪性能正常,并对影响仪器性能的各个参数进行准确校准。