Development of a Quantitative Method for Detection of Multiclass Veterinary Drugs in Feed Using Modified QuPPe Extraction and LC–MS/MS

A method was developed for the rapid and quantitative analysis of 30 veterinary drugs belonging to 17 classes (amphenicols (1), anthelmintics (1), cephalosporins (4), coccidiostats (1), lincosamides (1), macrolide (1), nitroimidazole (1), penicillins (3), phenylhydrazines (1), polypeptides (1), pyrethrins (1), quinolones (5), sulfonamides (3), tetracycline (3), neuroleptic agents (1), triazene trypanocidal agents (1), other. (1)) in feeds. The proposed method with a modified Quick Polar Pesticides (QuPPe) sample preparation was validated for the determination of 30 veterinary drugs in feed samples by liquid chromatography triple-quadrupole mass spectrometry (LC–MS/MS). The sample was extracted with methanol containing 1% acetic acid and purified by dispersive solid-phase extraction (d-SPE) with C18. Good linearity (r² ≥ 0.98) was observed, and the LOQ values ranged from 10 to 200 µg/kg. Average recoveries ranged from 70.8 to 118.4%, and the relative standard deviation was ≤ 18.7%. This validated method was used in the determination of 30 veterinary drugs in 142 feed samples obtained from South Korea. The results show that lincomycin was present in only one of the tested feed samples, although it was detected at a value lower than the LOQ. In conclusion, this multi-residue method can be used for screening through the detection and quantitation of residual multiclass veterinary drugs in feed samples.     

Preparation, characterization and metal sorption studies of a Chrome-Azurol-S-loaded anion-exchange resin

Chrome Azurol S (CS) was mobilized on an strongly basic anion-exchange resin (Dowex 2 x 4, in Cl(-) form) by batch equilibration. The modified resin was stable in acetate buffer solution and in 0.1 M HCl and H(2)SO(4), but it was readily degraded with 2-6 M HCl and HNO(3). Retention of Ba(II), Sr(II), Ca(II), Mg(II), Al(III), Cr(III), Zn(II), Fe(III), Ti(IV), Mn(II), Co(II), Ni(II), Cu(II), Cd(II) and Pb(II) was studied using the batch equilibration method. The uptake and recovery yields were determined by using inductively-coupled plasma atomic emission spectroscopy (for Mg, Al, Cr, Ti, Fe, Mn, Ni, Zn, Cu, Cd and Pb) and atomic absorption spectrophotometry (for Ba, Sr, Ca and Co). The optimum pH value was established for performing a selective separation of Al(III) from the other metal ions. The sorption capacities of the CS-loaded resing for Al(III), Cr(III), Mg(II) (at pH 6), Fe(III) (at pH 5) and Ti(IV) (at pH 4) were 14, 2.9, 0.3, 3 and 3.9 mumoles g(-1) respectively. On this basis a method for separating Al(III) from other cations was established.     

A potentiometric study of the oxidation of cobalt(II) with gold(III) chloride in presence of 1,10 phenanthroline or 2,2'-bipyridine : A new titration of cobalt (II) and its application to nickel-base alloys

The redox reaction between cobalt(II) and gold(III) chloride in the presence of 1.10-phenanthroline or 2,2'-bipyridine was studied, and a titration of the cobalt(II) complex with a gold(III) chloride solution was developed. A 4-fold amount of 1,10-phenanthroline or 2,2'-bipyridine was necessary for rapid quantitative reaction; the permissible pH range was 1.5–5. The oxidation of the cobalt(II) complex proceeds rapidly at 40–50°C, and a direct potentiometric titration was possible. The following maximum errors were obtained: 3.3% for 0.2–1.0 mg Co, 2.0% for 1–5 mg Co, and 0.70% for 10–40 mg Co. The following ions did not interfere: Ni(II), Zn(II), Pb(II), Cd(II), Mn(II), Fe(II), Cr(III), Al(III), Th(IV), Se(IV), Ti(IV), U(VI), Mo(VI), SO^2-₄ and PO^3-₄. Even small quantities of silver(I), copper(II), palladium(II), mercury(II)and iron(III) interfered. The method was applied to the determination of high cobalt contents in high-temperature nickel-base alloys.     

Determination of trace elements in bone by two-jet plasma atomic emission spectrometry

This paper describes an analytical method for trace element determination in bone tissues. The study of the influence of the bone matrix showed that the addition of 25% ground bone to graphite powder with introduced impurities did not affect the analytical signal of elements in the spectral excitation in a two-jet plasma. On basis of these investigations a method for direct multielement analysis of bone tissues was suggested. The sample preparation procedure consisted in mixing powdered bone (particle size 30 μm or less) with a spectroscopic buffer (graphite powder plus NaCl) in ratio 1:3 or to a greater extent depending on the analyte concentration. Reference samples based on graphite powder were used for construction of calibration curves. The NaCl concentration in analyzed and calibration samples was 15 wt%. The effect of particle size was revealed from the determination of Ba, Sr, and Mg. To eliminate this effect, treatment of the samples with nitric acid was proposed. The validation of the technique was confirmed by comparison of the analysis results of a bone sample with those obtained by inductively coupled plasma atomic emission spectrometry after wet acid digestion. The limits of detection estimated for 20 elements were the following (μg g^-1): 0.1 (Ag), 1.0 (Al), 1.0 (Ba), 0.1 (Be), 1.2 (Bi), 0.4 (Cd), 1.0 (Co), 0.2 (Cu), 0.6 (Cr), 1.9 (In), 2 (Fe), 0.3 (Ga), 0.4 (Mn), 0.4 (Mo), 0.7 (Ni), 1.0 (Pb), 0.7 (Sn), 0.8 (Tl), 5 (Sr), 1.0 (Zn).     

Simultaneous determination of 11 saponins in Panax notoginseng using HPLC-ELSD and pressurized liquid extraction

A new HPLC coupled with evaporative light scattering detection (ELSD) method was developed for simultaneous determination of 11 major triterpene saponins, namely notoginsenoside R1 (1), ginsenosides Rg1 (2), Re (3), Rf(4), Rb1 (5), Rg2 (6), Rc (7), Rb2 (8), Rb3 (9), Rd (10), and Rg3 (11) in Panax notoginseng, a commonly used traditional Chinese medicine (TCM). Pressurized liquid extraction (PLE) was employed for sample preparation, and the analysis was achieved using a Zorbax ODS C18 column eluted with gradient water-ACN in 60 min. The drift tube temperature of ELSD was set at 60 degrees C, and nitrogen flowrate was at 1.4 L/min. The method provided good repeatability and sensitivity for quantification of 11 saponins with overall precision (including intra- and interday) and LOD of less than 2.9% (RSD) and 98 ng, respectively. The validated method was successfully applied to quantify 11 saponins in 28 samples of P. notoginseng collected in different places, which is helpful to control the quality of P. notoginseng and its related products.     

Ion flotation behaviour of thirty-one metal ions in mixed hydrochloric/nitric acid solutions

The ion flotation of 31 metal ions in hydrochloric/nitric acid solution with the cationic surfactant cetylpyridinium chloride was investigated. A 25-ml portion of 0.27-2.87 x 10(-4)M metal ion and 1.8-6.0 x 10(-4)M cetylpyridinium chloride solution in 0.17-3.4M acid mixture ([HCl]:[HNO(3)] = 2.4:1) was subjected to flotation in a cell, 22.5 cm high and 4.0 cm in diameter, for 5 min, with nitrogen bubbles. Ir(IV), Pt(IV), Ge(IV), Sn(IV), Bi(III), Au(III), Tl(III), Pd(II) and Sn(II) were floated from solution in 95-100% yield; Ru(III), Rh(III), Ir(III), Hg(II), Ag(I) and Tl(I) were partly floated, while Cr(VI), Ti(IV), Zr(IV), Ga(III), In(III), Fe(III), Sb(III), Al(III), Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Zn(II), CD(II) and Pb(II) were floated with less than 20% yield. The flotation behaviour of these metal ions in the mixed acid system was compared with that in hydrochloric acid. The flotation is more efficient in the mixed acid system.     

On the mechanism of electroreduction of sulphur-containing ligands induced by the electroreduction of transition metal cations

The large scale electrolysis of Zn(II), Cd(II), Hg(II), Cu(II), Ni(II), Co(II), Co(III), Fe(II), Mn(II), Cr(II), Cr(III), Bi(III), In(III) and Sb(III) at mercury electrodes in presence of mercaptoacetic acid, 3-mercaptopropionic acid, cysteine and thiourea was carried out and the products were investigated. In case of transition metal ions the catalytic reduction of organic compounds resulting in the formation of sulphide ions was found. There are two possible ways of the production of these ions: (i) consisting in the formation of a complex between transition metal ion and organic ligand which is subsequently, reduced, and (ii) direct electroreduction of organic compound on the electrode modifiied by the deposition of metal and metal sulphide. For both cases the mechanism of electroreduction was discussed.     

Determination of anions using monolithic capillary column ion chromatography with end-to-end differential contactless conductometric detectors under resonance approach

An end-to-end differential measurement approach with capacitively coupled contactless conductivity detection (C(4)D) was applied to anion-exchange monolithic capillary column ion chromatography. The column was prepared by thermally initiated radical polymerization of poly(glycidyl methacrylate) in a fused-silica capillary of 320 μm i.d. and modified by quaternary ammonium latex surface coating. Two C(4)Ds were placed near both ends of the capillary column and the output difference between them was measured. With 15 mM potassium hydrogen phthalate used as the eluent, good separation of a mixture of inorganic anions (F(-), Cl(-), NO(2)(-), NO(3)(-)) was achieved. The detection limits of conventional C(4)D are 1.6, 0.28, 0.53, and 0.47 mg L(-1) for F(-), Cl(-), NO(2)(-), and NO(3)(-), respectively. To further enhance the sensitivity, the capacitive impedance from C(4)D was neutralized by an inductive impedance from a piezoelectric resonator. An increase in sensitivity by a factor of 7-8 was achieved in the resonating C(4)D in comparison with the conventional C(4)D. The detection limits of the resonating C(4)D are 0.23, 0.041, 0.065, and 0.059 mg L(-1) for F(-), Cl(-), NO(2)(-), and NO(3)(-), respectively. The response of the resonating C(4)D was analyzed based on an equivalent circuit model.     

Amphidinolides H2-H5, G2, and G3, new cytotoxic 26- and 27-membered macrolides from dinoflagellate Amphidinium sp

Six new macrolides, amphidinolides H2 (5), H3 (6), H4 (7), H5 (8), G2 (9), and G3 (10), have been isolated from a marine dinoflagellate Amphidinium sp. (strain Y-42). Cytotoxicity of five derivatives (11-15) of amphidinolide H (1) in addition to 10 amphidinolides (1-10) containing amphidinolides H (1), G (2), B (3), and D (4) was examined, and it was found that the presence of an allyl epoxide, an S-cis-diene moiety, and the ketone at C-20 was important for the cytotoxicity of amphidinolide H (1)-type macrolides.     

Study on adsorption behavior of cesium using ammonium tungstophosphate (AWP)-calcium alginate microcapsules

A functional microcapsule was prepared by encapsulating the fine crystalline ammonium tungstophosphate(AWP) in calcium alginate polymer(CaALG).The characterization of AWP-CaALG microcapsule was examined by SEM and EPMA.The adsorption behavior of Cs(I),Rb(I),Sr(II),Pd(II),Ru(III),Rh(III),La(III),Ce(III),Dy(III) and Zr(IV) was investigated by the batch method.The batch experiments were carried out by varying the shaking times,HNO 3 concentration,and initial concentration of metal ions.Relatively large K d values above 10 5 cm 3 /g for Cs(I) were obtained in the range of 0.1-5 M HNO 3,resulting in a separation factor of Cs/Rb exceeding 10 2.In contrast,the K d values of Sr(II),Pd(II),Ru(III),La(III),Dy(III),Ce(III) and Zr(IV) were considerably lower than 50 cm 3 /g.The K d value of Cs(I) decreased in the order of the coexisting ions,H + > Na + >> NH 4 +,and a linear relationship with a slop of about 1 was obtained between log K d and log [NH 4 + ]([NH 4 + ] > 0.01 M).The adsorption of Cs(I) was found to be controlled by chemisorption mechanism,and followed a Langmuir-type adsorption equation.A high uptake percentage of 99.4% for Cs(I) was obtained by using the dissolved solutions of spent fuel from FBR-JOYO(JAEA).     

Dynamic adsorption and desorption of heavy metal ions on poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber

The dynamic adsorption and desorption properties, including the effect of pH value and flow rate on the adsorption, eluent acidity and volume, eluting velocity and re-use, of Cu(II), Pb(II), Zn(II), Cd(II), Mn(II), Ni(II), Co(II) and Hg(II) ions on the column loaded with poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber were investigated. The recovery of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions in the presence of Na, K, Ca and Mg ions was examined. The preconcentration of trace amounts of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions from model solution samples was carried out with satisfactory results. The amount of the metal ions detected after preconcentration and recovery by this technique was basically in agreement with the added amount. The method is rapid, precise and simple. Received: 15 October 1997 / Revised: 17 March 1998 / Accepted: 20 March 1998     

Quality evaluation of Radix Astragali through a simultaneous determination of six major active isoflavonoids and four main saponins by high-performance liquid chromatography coupled with diode array and evaporative light scattering detectors

A method, high-performance liquid chromatography coupled with diode array and evaporative light scattering detectors (HPLC-DAD-ELSD), was developed to evaluate the quality of Radix Astragali through a simultaneous determination of six major active isoflavonoids and four main saponins. The wavelength at 280 nm was chosen to determine six isoflavonoids: calycosin-7-O-beta-D-glucoside (1), ononin (2), (6alphaR, 11alphaR)-9,10-dimethoxypterocarpan-3-O-beta-D-glucoside (3), (3R)-2'-hydroxy-3',4'-dimethoxyisoflavan-7-O-beta-D-glucoside (4), calycosin (5), and formononetin (6); and ELSD connected after DAD was employed to determine four saponins: astragaloside IV (7), astragaloside II (8), astragaloside I (9), and acetylastragaloside I (10). This assay was fully validated with respect to precision, repeatability and accuracy. The proposed method was successfully applied to quantify the ten components in eleven samples from different localities in China; significant variations were demonstrated in the content of these compounds in the samples from different areas. This simple, rapid, low-cost and reliable HPLC-DAD-ELSD method is suitable for routine quantitative analysis and quality control of traditional Chinese medicines (TCMs) consisting of bioactive multi-components with different structures such as Radix Astragali.     

Determination and on-line clean-up of (fluoro)quinolones in bovine milk using column-switching liquid chromatography fluorescence detection

A simple, cost-effective, and high throughput method using on-line column-switching liquid chromatography fluorescence detection was developed and validated for analysing five (fluoro)quinolones (FQs)--enrofloxacin (ENRO), ciprofloxacin (CIPR), sarafloxacin (SARA), oxolinic acid (OXOL), and flumequine (FLUM) in bovine milk. Norfloxacin (NORF) and nalixidic acid (NALI) were used as internal standards. After simple deproteination of milk sample with 5% (w/v) metaphosphoric acid, the supernatant was subject to on-line column clean-up and direct analysis by LC-FLD. The extraction cartridge was prepared in-house by slurry packing with hydrophilic-lipophilic polymer sorbent. The accuracy of measurement for each (fluoro)quinolone at different maximum residue limits (MRL) was 101-103% (ENRO), 92.8-97.4% (CIPR), 89.8-92.8% (SARA), 116-121% (OXOL), and 81.3-85.5% (FLUM), whilst the precision was 2.9-6.1% (ENRO), 2.5-5.1% (CIPR), 2.3-5.0% (SARA), 3.1-5.9% (OXOL), and 5.6-6.5% (FLUM). The decision limits, detection capabilities, specificity and analytes stability during storage were also investigated.     

Water adsorption and hydrolysis on molecular transition metal oxides and oxyhydroxides

Addition of water to molecular transition metal oxides (TiO2(g) and CrO3(g)) and oxyhydroxides (ScO(OH)(g), VO2(OH)(g), and MnO3(OH)(g)) was studied by means of quantum chemistry. In the investigated reactions, each reaction step comprised the breaking of one M=O bond and the formation of two OH groups. Exothermicity was observed when the product had tetrahedral or lower oxygen coordination. The reactions were found to involve stable water complexes as intermediates. The stabilities of such complexes were accentuated in the addition reaction Sc(OH)3(g) + H2O(g), in which the formation of a tetrahedral complex was found exothermic. For VO(OH)3(g), CrO2(OH)2(g), and MnO3(OH)(g), water addition to the remaining M=O bonds was found endothermic, whereas the formation of water complexes, using hydrogen bonds and preserving the oxyhydroxide kernel, was preferred. Thus, the sequence of such kernels for water clustering in the investigated reactions was found to be Sc(OH)3.H2O(g), Ti(OH)4(g), VO(OH)3(g), CrO2(OH)2(g), and MnO3(OH)(g). These stability considerations are important, as CrO2(OH)2(g) is believed to be the product of water-induced degradation of the protective chromium oxide scale on stainless steel at elevated temperatures.     

Ion-pair formation of a copper(II)-ammine complex with an anionic surfactant and the recovery of copper(II) from ammonia medium by the surfactant-gel extraction method.

The extraction and separation of copper(II), zinc(II), cobalt(II), and cadmium(II) were investigated. Both copper(II) and zinc(II) formed ammine-complexes, while cadmium(II) and cobalt(II) formed hydroxide precipitates in an ammonia medium. By the addition of sodium dodecylsulfate (SDS), a copper(II) complex formed an ion-pair (copper-ammine-DS), which was extracted into the SDS phase. However, a zinc(II) complex did not form an ion-pair, and was soluble in water. Copper(II) ion was recovered by stripping (back-extraction) after the addition of hydrochloric acid. This method was applied to the separation of copper(II) in a brass alloy.     

超临界流体色谱法分析大豆磷脂

 采用以CO2 为流动相的超临界流体色谱方法 ,以含 0 0 5 % (体积分数 )三乙胺的乙醇作为改性剂 ,对具有重要生物功能的大豆磷脂组成进行分析 ,获得了大豆磷脂提取物中 6个重要组分的定性结果 ,并讨论了流动相组成、操作温度和压力对分离的影响。对其中有代表意义的磷脂酰胆碱 (PC)进行了外标法定量分析 ,在PC质量浓度为0 0 2 0 g/L～ 0 0 75 g/L时具有较好的线性关系 ,PC加样回收率为 96 7% (n =5 ) ,重现性好。此方法可用于实际样品的分析。     

Trace determination of organotin compounds in water,sediment and mussel samples by low-pressure gas chromatography coupled to tandem mass spectrometry

A fast method for the determination of eight organotin compounds (OTs), monobutyltin (MBT), dibutyltin (DBT), tributyltin (TBT), tetrabutyltin (TeBT), monophenyltin (MPhT), diphenyltin (DPhT), triphenyltin (TPhT) and tetraphenyltin (TePhT), in water, sediments and mussels, was developed using low-pressure gas chromatography/tandem mass spectrometry (LPGC/MS/MS). The method is based on sodium diethyldithiocarbamate (DDTC) complexation of the ionic organotins, followed by extraction of the target matrices and derivatization by a Grignard reagent, as described in a previously published method for water samples. Solid-phase extraction was selected as extraction method from water samples after comparison with liquid-liquid extraction, but extraction of the OTs from sediment and mussel samples was performed using toluene. Matrix-matched calibration standards were used to minimize matrix effects. The analytical process was validated by the analysis of spiked blank samples. Performance characteristics such as linearity, detection limit (LOD), quantitation limit (LOQ), precision, and recovery were determined. Recoveries of OTs in spiked matrices ranged from 86-108% in water and from 78-110% in sediments and mussels, with precision values lower than 18%. Detection limits ranged from 0.1-9.6 ng L(-1) in water, and 0.03-6.10 microg kg(-1) in the other matrices. The present implementation of LPGC rather than conventional capillary GC permitted use of large-volume injection and reduced analysis time by a factor of two. The proposed methodology was applied to the determination of OTs in real samples of water, marine sediments and mussels from the west coast of the Mediterranean Sea (Spain).     

Halide ions complex and deprotonate dipicolinamides and isophthalamides: assessment by mass spectrometry and UV-visible spectroscopy

The F(-), Cl(-), and Br(-) binding selectivity of bis(p-nitroanilide)s of dipicolinic and isophthalic acids was studied by using competitive electrospray mass spectrometry and UV-Visible spectroscopy. Both hosts prefer binding Cl(-) over either F(-) or Br(-). Host deprotonation was observed to some extent in all experiments in which the host was exposed to halide ions. When F(-) was present, host deprotonation was often the major process, whereas little deprotonation was observed by Cl(-) or Br(-), which preferred complexation. A solution of either host changed color when mixed with a F(-), H(2)PO(4)(-), di- or triphenylacetate solution.     

2,3,7-Trihydroxyfluorones immobilized on cellulose matrices in test methods for determining rare elements

It was shown that 2,3,7-trihydroxyfluorones immobilized by adsorption on cellulose matrices can be used as reagents for the test determination of Mo(VI), Ti(IV), Ge(IV), Hf(IV), Nb(V), Ta(V), W(VI), Bi(III), V(IV), and Zr(IV). The change of the protolytic and complexing properties of trihydroxyfluorones immobilized on cellulose matrices was considered in comparison to corresponding properties in a solution. It was found that the reactions of trihydroxyfluorones with rare elements on cellulose matrices and in a solution exhibit similar effects upon the addition of cetylpyridinium. These effects are the bathochromic shift of the absorption maxima of the reagents and their complexes with analytes and the extension of the range of optimum acidity for complex formation. The complexation of salicylfluorones with the titanium(IV) in solution and on cellulose paper was studied by IR spectrometry. Phenylfluorone immobilized on a mixed-fiber cloth as used in test determinations of (mg/L) 0.05–5 Ti(IV), V(IV), Hf(IV), Nb(V), and Mo(VI); 0.01–5 Ge(IV) and Zr(IV); 0.05–1 Bi(III) and W(VI); and 0.1–5 Ta(V) by the color intensity of the indicator matrix after passing through 20 mL of a test solution. It was shown that phenylfluorone immobilized on cellulose paper can be used to determine (mg/L) 0.05–50 Ti(IV), 0.5–1000 Ge(IV), 0.5–500 Zr(IV), 5–200 Bi(III), 0.1–50 Mo(VI), 0.1–1000 V(IV), 0.1–100 Nb(V), 0.1–800 Hf(IV), 1–100 Ta(V), and 1–800 W(VI) by the length of the colored zone of a test strip after it was brought into contact with a test solution.     

Solvent Extraction Separation of Germanium(IV) with N-<Emphasis Type="Italic">n</Emphasis>-Octylaniline As an Extractant

The extraction behavior of germanium(IV) from aqueous hydrochloric acid solution with N-n-octylaniline in xylene was investigated. Hydrochloric acid concentration higher than 9 M remained effective for quantitative extraction of germanium(IV). Phenylfluorone ion as a counter anion was used. More than 2% N-n-octylaniline provided quantitative extraction at 1 min equilibrium time and germanium(IV) was back extracted by 7 M ammonia. The method was free from the interference of a large number of metal ions and anions, except for Te(IV) and Sn(IV); this was avoided using the masking effect. Germanium(IV) was separated from associated elements in its binary mixture with Si(IV), Te(IV), Sb(III), Bi(III), Au(III), Cu(II), Zn(II), and its ternary mixture with Se(IV), Te(IV); Sb(III), Bi(III); and Au(III), Cu(II). The proposed method was applied to a synthetic sample containing associated metal ions. The results indicated that trace amounts of germanium(IV) could be separated effectively from higher amounts of other elements.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 5, 2005, pp. 463–467.Original English Text Copyright © 2005 by Sargar, Anuse.This article was submitted by the authors in English.