钨丝电热原子吸收光谱分析法测定痕量锌

蒸馏水中的锌与吡咯烷二硫代氨基甲酸铵(APDC)形成的络合物用CCl4萃取后,弃去有机相,水相用作配制锌标准溶液和制备样品溶液,从而解决了用钨丝电热原子吸收光谱法测锌时空白值太高而难以进行实际样品分析的问题.考察了影响萃取和钨丝电热原子吸收测定的各种实验条件.在进样10 μL样品溶液时,本方法的定量下限为5 μg/L.测定了3个国家标准物质(大米、人发和水系沉积物)中的锌含量,结果与推荐值一致.     

便携式钨丝电热原子吸收光谱仪测定天麻中的铅

采用微波消解-小型钨丝电热原子吸收光谱仪在优化条件下测定了天麻中的铅。进样10μL时,检出限为10.1μg/L。对600μg/L铅标准溶液进行5次连续测定,测定结果的相对标准偏差为5.2%。铅的线性范围为100~1500μg/L,回归方程为A=0.0002c-0.0103,线性相关系数r=0.995 8。该法测定结果与电感耦合等离子体发射光谱仪(ICP-OES)测定结果接近,该方法简便、快速,可用于天麻样品中痕量铅的测定。     

超声辅助萃取-钨丝电热原子吸收光谱法测定痕量镉

镉对人体和动植物而言是一种非必需的元素,当其含量超过一定浓度就会产生毒性.由于镉在生物体内的半衰期长达1年之久,一旦进入生物体就不易排出.因此,测定食物样品中的镉对保证人类和动物的健康有重要的意义[1].     

钨丝电热蒸发-氩/氢火焰原子吸收光谱分析方法

基于钨丝电热蒸发设备,建立了一种全新的钨丝电热蒸发-氩/氢火焰串联原子吸收光谱系统.研究了系统抗酸、抗盐能力,结果表明:Na<'+>和Ca<'2+>质量浓度小于400 mg/L、Mg<'2+>质量浓度小于1500 mg/L时不干扰测定.在优化的仪器条件下:Pb、Cd、Au和Ag的检出限分别为:0.016、0.0005、...     

钨丝在原子吸收光谱分析中的应用

随着原子化器和检测器的小型化，钨丝原子吸收光谱分析仪在便携式分析仪器方面显示了很大的潜力。本文主要评述了近年来钨丝在电热原子吸收光谱分析中的应用，引用文献49篇。     

电沉积-钨丝电热原子吸收光谱法测定水样中的铅

研制了一种便携式钨丝电热原子吸收光谱分析装置,其主要包括:钨丝电热原子化器、多道微型CCD光谱仪、仪器电源系统以及控制系统。并将电沉积分离富集技术与该钨丝电热原子吸收光谱分析仪器结合,完成环境水样中铅的现场分析。并对铅的电沉积条件作了研究,最佳电沉积电位为负650 mV(vs.SCE),方法检出限:0.20μg/L,线性范围:1~15μg/L,对4μg/L Pb标准溶液10次重复测试,RSD为4.4%。     

钨丝在原子吸收光谱分析中的应用

随着原子化器和检测器的小型化,钨丝原子吸收光谱分析仪在便携式分析仪器方面显示了很大的潜力.本文主要评述了近年来钨丝在电热原子吸收光谱分析中的应用,引用文献49篇.     

便携式钨丝电热原子吸收光谱仪测定水样中铜、铬、铅和镉

以钨丝原子化器和小型化CCD检测器为主要部件,组装了便携式钨丝电热原子吸收光谱分析仪,优化了载气(Ar/H2) 流速、空心阴极灯位置、原子化器高度、灰化和原子化电流等主要仪器条件.最佳载气(Ar/H2)流速(mL/min)为600 /300(Cd),800/200(Cu, Pb, Cr);灰化电流为2.9～3.2 A;原子化电流为8.5 A;CCD的积分时间为50 ms.并在优化的仪器条件下准确测定了环境水样中的铜(Cu)、铬(Cr)、铅(Pb)和镉(Cd),进样10 μL时,其检出限分别为2、5、9和0.5 μg/L.此便携式原子吸收光谱仪在环境水样痕量元素分析中可望有良好的应用前景.     

电热原子吸收光谱法测定水中总钼

建立电热原子吸收法测定水中总钼的含量。样品采用硝酸–过氧化氢消解,热解涂层石墨管减小记忆效应,塞曼背景校正消除背景噪声。检测了27种共存离子的干扰影响。经6家实验室对标准物质和实际样品检测验证,方法检出限为0.6μg/L,能够满足微量检测要求。钼测定结果相对误差最大值为–6.2%,实验室内相对标准偏差为4.5%~7.6%(n=6),实验室间相对标准偏差为4.3%~5.7%(n=6),加标回收率为91.8%~104.0%。该方法精密度和准确度满足我国地下水和废水监测技术规范的质控要求。     

Determination of Cr(VI) by portable tungsten coil electrothermal atomic absorption spectrometer after surfactant-assisted dispersive liquid-liquid microextraction

As a new developed instrument, a portable tungsten coil electrothermal atomic absorption spectrometer (W-coil ET-AAS) was first coupled with surfactant assisted dispersive liquid–liquid microextraction (SA-DLLME) to improve its analytical performance and expand its applications in this work. SA-DLLME was very simple, rapid and the extraction efficiency was considerably improved by the effect of surfactant, which was suitable to be coupled with the portable instrument in field analysis. After SA-DLLME, concentrated chromium in organic phase was directly determined on W-coil atomiser. The influence factors relevant to SA-DLLME and instrumental conditions were studied systematically. Under the optimal conditions, the limit of detection (LOD) for Cr(VI) was 0.016 µg L^?1, with sensitivity enhancement factor (EF) of 107. The relative standard deviation (RSD) for seven replicate measurements of 0.5 µg L^?1 of Cr(VI) was 4.6%. The recoveries for the spiked samples were in the acceptable range of 96.8–104%. The rapid, simple and high effective method greatly improved the sensitivity of this portable spectrometer for the determination of Cr(VI) and was applied to the analysis of ultra-trace Cr(VI) in real and certified water samples with satisfactory results.     

Separation and preconcentration by flow injection coupled to tungsten coil electrothermal atomic absorption spectrometry

A flow injection system coupled to a tungsten coil electrothermal atomizer has been developed for on-line separation and preconcentration, using lead as a model element. The system utilizes three-way solenoid valves for sampling, buffering, washing and reconditioning solution management, and the resin column is inserted in the tip of the autosampler arm of a Varian GTA-96. The solenoid valves and tungsten coil power supply were controlled by a computer program written in Visual Basic, interfaced with the built-in Varian software. The system performance was tested by loading the resin column with the sample flowing at 3 ml min⁻¹ for 60 s. Elution was performed automatically by sampling 20 μl of the eluent from a sample cup of the autosampler, and this aliquot was delivered into a 150 W tungsten coil. With Chelex-100 resin, the separation of concomitants was tested with lead in the presence of as much as 1000 mg l⁻¹ of Ca, Mg, Na or K. The model system presented an enrichment factor of 64 at a sampling rate of 30 samples per hour.     

Chemical modifiers in arsenic determination in biological materials by tungsten coil electrothermal atomic absorption spectrometry

Palladium, iridium, and rhodium are evaluated as possible chemical modifiers in the determination of As in digest solutions of biological materials (human hair and clam) by tungsten coil electrothermal atomic absorption spectrophotometry (TCA-AAS). The modifier in solution was applied onto the coil and thermally pre-reduced; the pre-reduction conditions, the amount of modifier, and the thermal program were optimized. Palladium was not satisfactory, whereas Ir and Rh were effective modifiers and rendered better relative sensitivity for As by a factor of 1.4 and 1.9, respectively compared to the case without modifier. Upon optimization of thermal conditions for As in pre-reduced Ir (2.0 µg) and Rh (2.0 µg) modifiers and in the digest solutions of the study matrices, Rh (2.0 µg) was more effective modifier and was selected as such. The mean within-day repeatability was 2.8% in consecutive measurements (25–100 µg L^–1) (3 cycles, each of n=6) and confirmed good short-term stability of the absorbance measurements. The mean reproducibility was 4.4% (n=20 in a 3-day period) and the detection limit (3 _blank/slope) was 29 pg (n=15). The useful coil lifetime in Rh modifier was extended to 300–400 firings. Validation was by determination of As in the certified reference material (CRM) of Oyster tissue solution with a percentage relative error (E _rel%) of 2% and percentage relative standard deviation (RSD%) of 3% (n=4), and by analytical recovery of As spiked in CRM of human hair [94±8% (n=4)]. The methodology is simple, fast (sample readout frequency 21 h^–1), reliable, of low cost, and was applied to the determination of As in hair samples of exposed and unexposed workers.     

电沉积-钨丝电热原子吸收光谱法测定地质样品中痕量金

以市售幻灯投仪卤钨灯泡钨丝为原子化器的钨丝电热原子吸收光谱分析仪(TC-AAS),功率小、仪器成本低[1,2],如用微型CCD光谱仪作检测系统,可以实现原子吸收光谱仪的小型化,甚至可用于野外现场分析[3,4].     

Comparison of tungsten coil electrothermal vaporization and thermospray sample introduction methods for flame furnace atomic absorption spectrometry

Flame furnace atomic absorption spectrometry (FF-AAS) is a newly developed flame atomic absorption spectrometric technique based on arranging a flame furnace onto the top of the flame burner head. In this fundamental investigation, 25 elements were carefully tested by using either thermospray FF-AAS or tungsten coil electrothermal vaporization FF-AAS, of which 15 volatile and semi-volatile elements (Cd, Tl, Ag, Pb, Zn, Hg, Cu, Sb, Bi, Te, In, As, Se, Sn and Au) exhibited better limits of detection compared to those by conventional FAAS; however, non-volatile or refractory elements (Fe, Co, Ni, Cr, Mn, Pd, Pt, Al, Be and V) showed inferior sensitivities by the proposed methods.     

火焰原子吸收光谱法测定废旧二次电池中钴的含量

建立了火焰原子吸收光谱(FAAS)法测定废旧二次电池中钴的方法。确定了最佳溶样方法和仪器测定的最佳条件,在选定的操作条件下,钴的检出限0.015μg/mL,相对标准偏差为0.98%～1.9%,加标回收率为98.0%～105%。用来测定废旧二次电池中的钴,操作简单、快速、灵敏度高,结果令人满意。     

A comparative study of chemical modifiers in the determination of total arsenic in marine food by tungsten coil electrothermal atomic absorption spectrometry

Three platinum group elements (Pd, Ir and Rh) both in solution and in pre-reduced form, and also combined with Mg(NO₃)₂ or ascorbic acid, were assessed as possible chemical modifiers on the atomization of As in digest solutions of seafood matrices (clam and fish tissue) by tungsten coil electrothermal atomic absorption spectrometry (TCA-AAS) and compared without a modifier. Of 28 modifier alternatives in study including single form and binary mixtures, and based on maximum pyrolysis temperature without significant As loss and best As absorbance sensitivity during atomization, three modifiers: Rh (0.5 μg), Ir (1.0 μg) and Rh (0.5 μg) + ascorbic acid (0.5 μg), at optimum amounts were pre-selected and compared. The definitive modifier (rhodium (0.5 μg)) was selected by variance analysis. The mean within-day repeatability was 3% in consecutive measurements (25-300 μg l⁻¹) (three cycles, each of n = 6) and showed good short-term stability of the absorbance measurements. The mean reproducibility was 4% (n = 18 in a 3-day period) and the detection limit (3σ_blank/slope) was 42 pg (n = 16). Quantitation was by standard additions to compensate for matrix effects not corrected by the modifier. Three sample digestion procedures were compared in fish and clam tissue samples: microwave acid digestion alone (A) or combined with the addition of 2% (m/v) K₂S₂O₈ solution followed either by UV photo-oxidation (B) or re-digestion in a thermal block (C). The accuracy was established by determination of As in certified reference material of dogfish muscle (DORM-2). Procedures B and C showed good recoveries (102% (n = 4) and 103% (n = 7), respectively), whereas procedure A was not quantitative (85%). The methodology is simple, fast, reliable, of low cost and was applied to the determination of total As in lyophilized samples of clam and fish collected in the Chilean coast.     

Uncertainty of atomic absorption spectrometer

The uncertainty of the flame atomic absorption spectrometer was studied. Drift of signal, noise, and nonlinearity of the calibration curve were found to be main sources of uncertainty for the absorbance measurement, and factors affecting these sources of uncertainty were evaluated using Cd as a typical element. The combined uncertainty was 0.00133 absorbance units at a Cd concentration of 0.5 mg/l (0.078 absorbance units). The relationship between the flame conditions and the burner optics contributed strongly to the uncertainty. Therefore, the matrix effect of the sample must to be taken into consideration in actual analyses.