Determination of cadmium, lead and copper in wine by differential pulse anodic stripping voltammetry

Summary The simultaneous determination of cadmium, lead and copper in wine by differential pulse anodic stripping voltammetry at the hanging mercury drop electrode is described. The wine samples are decomposed in a mixture of sulphuric acid and hydrogen peroxide at 180° C. The procedure is controlled by recovery tests and compared with other wet digestion methods. The results for ten red and white wine samples of different origin are given. The lead values (65–230 ppb) were below the accepted maximum level for this metal, but some of the wines contained relatively large amounts of copper (0.08–1.04 ppm). Very low values (1.4–6.6 ppb) were found for cadmium.

---

Bestimmung von Cadmium, Blei und Kupfer in Wein durch Differentialpulse-anodic-stripping Voltammetrie

Zusammenfassung Bei dem beschriebenen Verfahren werden die Proben mit Schwefelsäure/Wasserstoffperoxid bei 180° C aufgeschlossen. Recovery Tests und Vergleiche mit anderen Naßaufschluß-methoden wurden durchgeführt. Ergebnisse für 10 Proben von Rot- und Weißweinen verschiedenen Ursprungs werden angegeben. Die Bleigehalte (65–230 ppb) lagen unter den zugelassenen Maximalwerten. Einige Weine wiesen jedoch relativ hohe Kupfergehalte auf (0,08–1,04 ppm). Cadmium wurde nur in sehr geringen Mengen gefunden (1,4–6,6 ppb).

We would like to thank A/S Vinmonopolet for supplying the wine samples, and the Royal Norwegian Council for Scientific and Industrial Research for a postdoctoral fellowship (M. Oehme).     

Anodic stripping voltammetry at a mercury film electrode: baseline concentrations of cadmium,lead, and copper in selected natural waters

A simple, rapid, and inexpensive anodic stripping voltammetric method with a mercury thin film electrode is reported for the establishment of baseline concentrations of cadmium, lead, and copper in natural waters. The procedure for routine surface preparation of wax-impregnated graphite mercury film electrodes requires about 30 min. Concentrations in the 0.006–6 μg l^-1 range are determined by linear d.c. voltage sweeps; the total time for a plating and stripping cycle is 6 min or less. The need for pressure-digesting samples for copper determinations is demonstrated. The a.s.v. results correlate well with corresponding analyses performed by graphite-furnace atomic absorption spectrometry.     

Determination of lead, cadmium, copper and zinc in human tissues by differential pulse anodic stripping voltammetry

Summary A convenient electroanalytical technique for the simultaneous determination of lead, cadmium, copper and zinc in human blood and teeth is described. The method is based on differential pulse anodic stripping voltammetry at the static mercury drop electrode (SMDE). Optimum conditions for the anodic stripping of Pb, Cd, Cu and Zn were determined using ammonium acetate and dilute nitric acid (pH 2) as electrolytes. Interferences from other metals were not observed and the estimations were reproducible within a standard deviation of±4%. Low blank values and high sensitivity of the method allowed the determinations at sub-ppb levels with an electrolysis time of 1–3 min. The accuracy of the method has been tested by comparison with the results obtained by mass spectrometry and atomic absorption spectrometry. The results and findings are discussed in brief.

---

Bestimmung von Blei, Cadmium, Kupfer und Zink in menschlichen Geweben mit Hilfe der Differentialpuls-Anodic Stripping Voltammetrie

Zusammenfassung Eine vorteilhafte elektroanalytische Methode zur Bestimmung von Pb, Cd, Cu und Zn in menschlichem Blut und in Zähnen wird beschrieben. Das Verfahren beruht auf der Differentialpuls-Anodic Stripping Voltammetrie an der statischen Quecksilbertropfelektrode. Mit Hilfe von Ammoniumacetat und verdünnter Salpetersäure (pH 2) als Trägerelektrolyten wurden die optimalen Bedingungen ausgearbeitet. Störungen durch andere Metalle wurden nicht beobachtet. Die Standardabweichung betrug ±4%. Infolge der niedrigen Blindwerte und der hohen Empfindlichkeit konnten Bestimmungen im Sub-ppb-Bereich mit Elektrolysezeiten von 1–3 min durchgeführt werden. Die Genauigkeit der Methode wurde durch Vergleich mit massenspektrometrischen und AAS-Untersuchungen bewiesen. Die Ergebnisse werden kurz diskutiert.

     

Determination of thallium in natural waters by anodic stripping voltammetry

Thallium was determined in natural waters by anodic stripping voltammetry at a hanging mercury drop electrode, in acetate buffer pH 4.6+EDTA, after preconcentration and separation on an anion exhange resin. For Pacific Ocean surface waters a mean value of 13.0±1.4 ng Tl l^?1 was found, while for freshwater samples the value was 3.7±1.0 ng Tl l^?1. Thermodynamic considerations of thallium speciation predict that both in seawater and freshwater thallium exists primarily in the trivalent state. This was confirmed by experiment.     

Determination of pyrithione in natural waters by cathodic stripping voltammetry

A method was developed to determine the biocide pyrithione in natural waters. The method is based on cathodic stripping voltammetry (CSV) in the presence of Triton-X-100, which is used to separate the peak from interfering thiol compounds. Optimised conditions include a Triton-X-100 concentration of 4 ppm and a pH adjusted to 9 using ammonia buffer. The adsorption potential for pyrithione was −0.10 V and the peak occurred at −0.2 to −0.3 V. Detection was by differential-pulse CSV. The detection limit in UV-digested seawater was 1.5 nM for a deposition time of 60 s. In principle, this limit of detection could be lowered by extending the adsorption time, but in practice this may not be possible due to interferences by other organic compounds (surfactants and thiol compounds) in natural waters.     

Determination of copper and lead in schist by anodic stripping voltammetry

Samples were decomposed in HClO₄/HF mixture in a Teflon beaker to avoid electrochemical interference from platinum ions. The residue remaining after evaporation to dryness was taken up in nitric acid and examined by anodic stripping voltammetry. Both the hanging mercury drop electrode and the rotating glassy carbon electrode, mercury-plated in situ, were used with success. Copper at 120 ppm and lead at 40 ppm were determined with a relative standard deviation of 6%. The schist was the Nordic reference sample ASK-2.     

Determination of copper, lead and cadmium in whole blood by stripping voltammetry with the use of graphite electrodes

The problem with toxic metal ion determination in blood is the adsorption of organic compounds on the electrode surface and the formation of complexes between metal ions and organic constituents of blood. This is the reason why usually preliminary acid digestion or other sample pretreatment is used. Two kinds of electrodes have been used: “Ultra-Trace Electrode”, made from impregnated graphite (I), and thick film graphite disposable electrodes (II). The analysis of whole blood with different sample preparation methods shows, that chemical digestion is not necessary for the analysis. Electrochemical two-stage sample preparation provides the possibility for analysing whole blood with the mentioned electrodes. Thick film disposable electrodes are less sensitive to the interference of organic constituents of blood. These electrodes give the possibility to determine total cadmium, lead and copper concentration in whole blood without special sample pretreatment. The application of “Ultra-Trace Electrode” for blood analysis is possible only after preliminary pretreatment of blood by chemical digestion or electrochemical sample preparation.     

Use of ultramicroelectrodes for determining lead in natural waters by stripping voltammetry

Anin situ obtained graphite-fiber-based thin-film mercury microelectrode was used for determining lead(II) in natural water by stripping voltammetry without removing oxygen and using no supporting electrolyte. Under the optimum voltammetric conditions (E _el = -1.2 V,t _el = 5 min,c _Hg(II) = 1 x 10^-7 M, ΔE = 40 mV, v= 105 mV/s), the calibration graph was linear in the range of actual lead(II) concentrations in natural waters. At a lead(II) concentration of 0.002 mg/L, the RSD was 11%.     

Interferences in the determination of copper in natural waters by anodic stripping voltammetry

Copper(I)-binding anions such as cyanide and thiocyanate, and polysaccharides, when present in non-saline waters are shown to produce an additional, more anodic wave during the determination of copper by stripping voltammetry. The origins of this wave and potential interferences in determinations of copper and copper-complexing capacities are discussed. The effect of inadequate oxygen removal is reported.     

Determination of cadmium, copper and lead in natural waters after anion-exchange separtion.

A method is described for the determination of cadmium, copper and lead in samples of natural non-saline waters. After acidification with hydrobromic acid, the water sample is filtered and, following the addition of ascorbic acid, passed through a column of the strongly basic anion-exchange resin Dowex 1-X8 (bromide form). On this exchanger cadmium(II). copper(I) and lead(II) are adsorbed as anionic bromide complexes. After elution of these elements with 1 M nitric acid, the determinations by atomic absorption spectrometry are carried out in a medium consisting of 90% ($\text{v}\text{v}$) methanol and 10% ($\text{v}\text{v}$) 1.5 M hydrobromic acid. The procedure was used for the routine determination of cadmium, copper and lead in water samples collected in Austria.     

The determination of cadmium,lead and copper in urine by differential pulse anodic stripping voltammetry

Differential pulse anodic stripping voltammetry is used for the simultaneous determination of cadmium, lead and copper in different types of urine samples. Unlike most biological samples, urine can be analyzed directly for cadmium and lead without pretreatment of the sample; a significant increase in sensitivity is obtained if the analysis is carried out at an elevated temperature. The complete decomposition of urine with a mixture of nitric, perchloric and sulphuric acids is also described; this procedure makes it possible to determine copper simultaneously. Good agreement was obtained between the two procedures, and the recovery of metals from spiked samples was satisfactory for both methods. The relative merits of the two approaches are discussed.     

The determination of copper,lead and cadmium in an oyster homogenate by anodic stripping voltammetry

Oyster homogenate is digested with nitric and perchloric acids and analyzed by differential pulse anodic stripping voltammetry. The results are compared with the “probable concentrations” obtained from an intercalibration exercise.     

Determination of cadmium, lead and copper in wine by potentiometric stripping analysis

A procedure for the determination of Cd, Pb and Cu in different wine samples after simple sample preparation on a mercury film electrode (MFE) by potentiometric stripping analysis (PSA) is presented. In 150 German wine samples collected in 1993/94 the following values were found: Cd mean: 0.63 ng/mL (range: 0.003– 0.98 ng/mL); Pb mean: 50 ng/mL (range: 4–254 ng/mL); Cu mean: 250 ng/mL (range: 50–394 ng/mL).     

The determination of copper,lead, cadmium and zinc in human teeth by anodic stripping voltammetry

Differential pulse anodic stripping voltamrnetry and a hanging mercury drop electrode are used for the determination of copper, lead, cadmium and zinc in Norwegian teeth and pure hydroxyapatite. Special attention is given to the choice of decomposition procedure and the determination of the blank values. A complete dissolution of the tooth material and satisfactory blank values can be obtained by using decomposition with nitric acid in a Teflon bomb.     

The determination of copper,lead and cadmium in sea water by differential pulse anodic stripping voltammetry

The effect of various instrumental parameters is investigated and optimized conditions established. The results are in accordance with the theory of differential pulse anodic stripping voltammetry. Both a hanging mercury drop electrode, and a rotating glassy carbon electrode mercury plated in situ were used. The best detection limit is obtained with the mercury film electrode, but the hanging mercury drop electrode is more reproducible. The differential pulse stripping technique is compared to linear sweep stripping, and increased sensitivity and better peak separation is demonstrated for the former technique, particularly when a hanging mercury drop electrode is used. However, the differential pulse technique will also improve the detection limit for a mercury film electrode, if the electrode has a non-ideal response with a corresponding high background current.     

Determination of lead and cadmium in titanium dioxide by differential pulse anodic stripping voltammetry

A procedure for the simultaneous determination of lead and cadmium in TiO(2) by differential pulse anodic stripping voltammetry (ASV) has been developed. The key feature of the method is the use of triethanolamine (TEA) to remove titanium interference: TiO(2) undergoes acidic digestion with HF/H(2)SO(4) at atmospheric pressure, TEA is added to the HCl solution of the residue and the solution is analysed using a standard ASV instrumentation, equipped with a hanging mercury drop electrode. The calibration curves for both lead and cadmium are linear up to 50 mugl(-1) of solution, and the detection limits are 1 mugl(-1), corresponding to 1 mugg(-1) of TiO(2). Method reliability was tested by comparing the results with those given by electrothermal atomic absorption spectroscopy. The method has been successfully applied for determination of both contaminants in powdered titanium dioxide (raw materials) and in titanium dioxide-containing cosmetics (sunscreen products).