Influence of Mass Ratio on Forward and Reverse Ballistic Impact Equivalence: Experiments,Simulations, and Mechanism Analysis

Reverse ballistic impact tests are widely used for studying dynamic responses because they provide more comprehensive and quantitative projectile/rod response results than forward impact tests. To examine equivalent forward and reverse conditions, a series of 8-cm length oxygen-free copper rods with varying length–diameter ratios was used in forward and reverse ballistic Taylor impact experiments with velocities and strain ratios of 104–215 m/s and 1.25?×?10³–2.5?×?10³ s^-1, respectively. Digital image correlation (DIC) and traditional optical measurements were used to determine instantaneous responses at the μs level. Based on DIC, transient structural deformation, and plastic wave propagation, the forward and reverse length difference at similar velocities ranges from 2 to 6.95 %. Rules governing deformation from the perspective of energy, along with rules for changes in energy and plastic wave propagation were determined. The relative deformation energy error was below 5 % for target projectile mass ratios above 20.     

Experimental investigation and modeling of the tension behavior of polycarbonate with temperature effects from low to high strain rates

The effects of strain rate and temperature on the tension stress–strain responses of polycarbonate are experimentally investigated over a wide range of strain rates (0.001–1700 s⁻¹) and temperatures (0–120 °C). A modified split Hopkinson tension bar is used for high-rate uniaxial tension tests. Experimental results indicate that the stress–strain responses of polycarbonate at high strain rates exhibit the nonlinear characteristics including the obvious yielding and strain softening. The tension behavior is strongly dependent on the strain rate and temperature. The values of yield stress and strain at yield present a dramatic increase at higher strain rates and decrease with the increase in temperature. Moreover, there exists a significant rate-sensitivity transition in the polycarbonate tension yield behavior. Based on the experimental investigation, a physically based three-dimensional elastoplastic constitutive model for the finite deformation of glassy polymers is used to characterize the rate-temperature dependent yield and post-yield behavior of polycarbonate when subjected to tension loading. The model results are shown close to the experimental data within the investigated strain-rate and temperature ranges.     

Mechanics of the rate-dependent elastic–plastic deformation of glassy polymers from low to high strain rates

A combined experimental and analytical investigation has been performed to understand the mechanical behavior of two amorphous polymers—polycarbonate and poly(methyl methacrylate)—at strain rates ranging from 10⁻⁴ to 10⁴ s⁻¹. This range in strain rates was achieved in uniaxial tension and compression tests using a dynamic mechanical analyzer (DMA), a servo-hydraulic testing machine, and an aluminum split-Hopkinson pressure bar. DMA tension tests were used to characterize the viscoelastic behavior of these materials, with focus on the rate-dependent shift of material transition temperatures. Uniaxial compression tests on the servo-hydraulic machine (10⁻⁴ to 1 s⁻¹) and the split-Hopkinson pressure bar (10³ to 10⁴ s⁻¹) were used to characterize the rate-dependent yield and post-yield behavior. Both materials were observed to exhibit increased rate sensitivity of yield under the same strain rate/temperature conditions as the β-transition of the viscoelastic behavior. A physically based constitutive model for large strain deformation of thermoplastics was then extended to encompass high-rate conditions. The model accounts for the contributions of different molecular motions which become operational and important in different frequency regimes. The new features enable the model to not only capture the transition in the yield behavior, but also accurately predict the post-yield, large strain behavior over a wide range of temperatures and strain rates.     

Modeling and validation of the large deformation inelastic response of amorphous polymers over a wide range of temperatures and strain rates

A robust physically consistent three-dimensional constitutive model is developed to describe the finite mechanical response of amorphous polymers over a wide range of temperatures and strain rates, including the rubbery region and for impact loading rates. This thermomechanical model is based on an elastic–viscoplastic rheological approach, wherein the effects of temperature, strain rate, and hydrostatic pressure are accounted for. Intramolecular, as well as intermolecular, interactions under large elastic–inelastic behavior are considered for the mechanisms of deformation and hardening. For a wide range of temperatures and strain rates, our simulated results for poly(methyl methacrylate) (PMMA) and polycarbonate (PC) are in good agreement with experimental observations.     

Effect of crack-tip shape on the near-tip field in glassy polymer

The physical nature of a crack tip is not absolutely sharp but blunt with finite curvature. In this paper, the effects of crack-tip shape on the stress and deformation fields ahead of blunted cracks in glassy polymers are numerically investigated under Mode I loading and small scale yielding conditions. An elastic–viscoplastic constitutive model accounting for the strain softening upon yield and then the subsequently strain hardening is adopted and two typical glassy polymers, one with strain hardening and the other with strain softening–rehardening are considered in analysis. It is shown that the profile of crack tip has obvious effect on the near-tip plastic field. The size of near-tip plastic zone reduces with the increase of curvature radius of crack tip, while the plastic strain rate and the stresses near crack tip enhance obviously for two typical polymers. Also, the plastic energy dissipation behavior near cracks with different curvatures is discussed for both materials.     

Full-field characterization of mechanical behavior of polyurethane foams

The foam material of interest in this investigation is a rigid closed-cell polyurethane foam PMDI with a nominal density of 20 pcf (320 kg/m³). Three separate types of compression experiments were conducted on foam specimens. The heterogeneous deformation of foam specimens and strain concentration at the foam–steel interface were obtained using the 3-dimensional digital image correlation (3D-DIC) technique. These experiments demonstrated that the 3D-DIC technique is able to obtain accurate and full-field large deformation of foam specimens, including strain concentrations. The experiments also showed the effects of loading configurations on deformation and strain concentration in foam specimens. These DIC results provided experimental data to validate the previously developed viscoplastic foam model (VFM). In the first experiment, cubic foam specimens were compressed uniaxially up to 60%. The full-field surface displacement and strain distributions obtained using the 3D-DIC technique provided detailed information about the inhomogeneous deformation over the area of interest during compression. In the second experiment, compression tests were conducted for cubic foam specimens with a steel cylinder inclusion, which imitate the deformation of foam components in a package under crush conditions. The strain concentration at the interface between the steel cylinder and the foam specimen was studied in detail. In the third experiment, the foam specimens were loaded by a steel cylinder passing through the center of the specimens rather than from its end surface, which created a loading condition of the foam components similar to a package that has been dropped. To study the effects of confinement, the strain concentration and displacement distribution over the defined sections were compared for cases with and without a confinement fixture.     

An experimental study of inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading

An experimental study was conducted on the inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading. Thin-walled tubular specimens were used and small strain gages were bonded on the specimen surface to characterize the local deformation. The controlled loading paths included cyclic tension–compression, cyclic torsion, proportional axial-torsion, 90°-out-of-phase axial-torsion, and fully reversed torsion with a constant axial stress. The maximum stress in each experiment was lower than the lower yield stress of the material. It was found that the cyclic plastic deformation within the gage section of the specimen under multiaxial stress state followed the three-stage process that was observed from uniaxial loading, namely, incubation, propagation, and saturation. The plastic deformation was significantly inhomogeneous during the propagation stage, and the inhomogeneity continued through the saturation stage. The duration of each stage and the saturated strains were dependent on the cyclic stress amplitude and the loading path. Multiaxial stress state reduced the incubation stage. With identical equivalent stress magnitude, the nonproportional loading path resulted in the shortest incubation and propagation stages, and the saturated equivalent plastic strain magnitude was the smallest. Although the deformation over the gage section was inhomogeneous, the plastic deformation in a given local area was found to be practically isotropic.     

Effect of the rate of deformation on the crystallization behavior of polymers

Deformation has a significant influence on the crystallization process in a number of polymers. In this paper, the response of a recently developed model for crystallizing polymers is investigated when subject to uni-, bi-axial and constant width extensions for a range of strain rates. Both the loading and unloading behavior are examined for these deformations. The particular model studied here was developed to capture the effect of strain induced crystallization in polymers and has been applied to model crystallization in polyethylene terephthalate at temperatures just above its glass transition temperature. The model has been formulated using the notion of multiple natural configurations within a full thermodynamic framework. The connection between micro-structural changes taking place in the polymer and the form of the model are elucidated. The interplay between the relaxation processes, the rate of deformation and their combined effect on crystallization is illustrated. The results show an earlier onset of crystallization for high strain rates due to stretching of the polymer network. At low strain rates however, crystallization is not observed as the polymer network is able to relax during the deformation. A sharp upturn in the stress is observed after the onset of crystallization due to the formation of a rigid crystalline phase. The unloading curves clearly show a hysteric behavior with the amount of dissipation increasing for increasing values of strain rate. These results compare favorably with experimental observations available in literature.     

Effect of strain rate,moisture and temperature on the deformation behavior of polymer roll covers

Soft polymer roll covers, which are used in certain positions of paper manufacturing machines, have a vital role in the dynamics of two mating rotating rolls (i.e., nip dynamics). The polymer covers are often used in moist conditions where the loading rates are rather high and temperatures may vary from 45 to 60°C. In this paper, we study the dynamic mechanical behavior of two soft polyurethane composite roll covers under different conditions of temperature, moisture, and loading rate. For the tests in compression, both servohydraulic materials testing machines and the split Hopkinson pressure bar technique were used in the strain rate range of 0.001–1500 s⁻¹. The specimens, which were to be tested under moist conditions, were immersed in paper machine water (pH 4.5) until saturated moisture content was reached. The materials showed remarkable softening as well as decrease in the strain rate sensitivity in moist conditions.     

Experimental and numerical investigations into collapse behaviour of thin spherical shells under drop hammer impact

A study of the collapse behaviour of hemi spherical and shallow spherical shells and their modes of deformation under impact loading are presented in this paper. Aluminium spherical shells of various radii and thicknesses were made by spinning. These were subjected to impact loading under a drop hammer and the load histories were obtained in all the cases. Three-dimensional numerical simulations were carried out for all the tested specimen geometries using LS-DYNA^®. Material, geometric and contact nonlinearities were incorporated in the analysis. The uni-axial stress–strain curve for the material was obtained experimentally and was assumed to be piecewise linear in the plastic region. The results from impact experiments are used for the validation of the numerical simulations. Three distinct modes of deformation, namely local flattening, inward dimpling and formation of multiple numbers of lobes were analysed and influence of various parameters on these modes is discussed.     

45钢的J-C损伤失效参量研究

为了在结构碰撞效应的有限元分析中描述材料行为,通过开展45钢在不同应力状态和温度下的准静态材料力学性能实验及拉伸SHB实验,考察了应力状态三轴度、温度和应变率对材料失效应变的影响。由实验数据得到了Johnson-Cook失效模型参量,并通过出现失效的Taylor撞击实验和数值模拟进行了一定的验证,表明模型描述与实验结果的趋势一致。     

基于能量变化的微尺度金属应变突变准则研究

微尺度金属在塑性变形过程中呈现出显著的应变突变特性.论文以力加载条件下单晶Ni微米柱体和位移加载下Au纳米柱体为对象,探讨应变突变的判定准则与不同特征阶段的判别条件.首先从经典塑性理论Hill稳定性条件出发,分析微柱体变形过程中的动能变化,提出了应变突变发生与结束的判定准则.进一步分析柱体变形过程中的内能变化,结合动能变化的分析结果,给出了微尺度金属不同变形阶段的判别条件.通过与文献中实验与理论结果对比发现,基于动能变化的应变突变判定准则能够判断应变突变的发生与结束,基于能量变化的判别条件可以有效区分微柱体的不同变形阶段.最后对新理论准则的可靠性与适用性进行了讨论.     

Lüders bands propagation of 1045 steel under multiaxial stress state

Inhomogeneous plastic deformation of 1045 steel under monotonic loading was experimentally studied. Thin-walled tubular specimens were used in the experiments and custom-made small strain gages were bonded on the specimen surface to characterize the local deformation. Experiments were conducted under tension, torsion, and combined tension–torsion. During the propagation of Lüders bands, the local deformation experienced two-stage deformation: an abrupt plastic deformation stage followed by a slower deformation process. In some area of the gage section of the specimen, a small amount of initial plastic deformation occurred before the Lüders front reached. During the propagation of Lüders bands, multiple Lüders fronts can be formed. Under tension, torsion, and combined tension–torsion with a constant axial load, the Lüders front was approximately parallel to the material plane of maximum shear stress. When the combined axial-torsion followed a proportional fashion, the stress–extensometer strain responses were dependent on the axial/torsional loading ratio, and the Lüders fronts were oriented differently and propagated along the specimen axis at a different velocity. The local strain was inhomogeneous even at the work-hardening stage. The relationships between the equivalent stress and the equivalent plastic strain were found to be practically identical for all the loading cases studied.     

Dynamic limit analysis formulation for impact simulation of structural members

This paper introduces an extended concept of limit analysis to deal with the dynamic equilibrium condition considering the inertia and strain-rate effect for dynamic behavior of structures. The conventional limit analysis method has been applied to only static collapse analysis of structures without consideration of dynamic effects in the structural behavior. A dynamic formulation for the limit analysis has been derived for incremental analysis dealing with time integration, strain and stress evaluation, strain hardening, strain-rate hardening and thermal softening. The time dependent term in the governing equation is integrated with the WBZ-α method. The dynamic material behavior is described by the Johnson–Cook model in order to consider strain-rate hardening and thermal softening as well as strain hardening. Simulations have been carried out for impact analysis of a Taylor bar and an S-rail and their numerical results are compared with elasto-plastic explicit analysis results by LS-DYNA3D. Comparison demonstrates that the dynamic finite element limit analysis can predict the crashworthiness of structural members effectively with less effort and computing time than the commercial code compared. The crashworthiness of a structure with the rate-dependent constitutive model is also compared to that with the quasi-static constitutive relation in order to investigate the dynamic effect on deformation of structures.     

A dynamic finite element method for inhomogeneous deformation and electromechanical instability of dielectric elastomer transducers

We present a three-dimensional nonlinear finite element formulation for dielectric elastomers. The mechanical and electrical governing equations are solved monolithically using an implicit time integrator, where the governing finite element equations are given for both static and dynamic cases. By accounting for inertial terms in conjunction with the Arruda–Boyce rubber hyperelastic constitutive model, we demonstrate the ability to capture the various modes of inhomogeneous deformation, including pull-in instability and wrinkling, that may result in dielectric elastomers that are subject to various forms of electrostatic loading. The formulation presented here forms the basis for needed computational tools that can elucidate the electromechanical behavior and properties of dielectric elastomers that are used for engineering applications.     

Dynamic Tensile Characterization of a 4330-V Steel with Kolsky Bar Techniques

Dynamic tensile experimental techniques of high-strength alloys using a Kolsky tension bar implemented with pulse shaping and advanced analytical and diagnostic techniques have been developed. The issues that include minimizing abnormal stress peak, determining strain in specimen gage section, evaluating uniform deformation, as well as developing pulse shaping for constant strain rate and stress equilibrium have been addressed in this study to ensure valid experimental conditions and obtainment of reliable high-rate tensile stress–strain response of alloys with a Kolsky tension bar. The techniques were applied to characterize the tensile stress–strain response of a 4330-V steel at two high strain rates. Comparing these high-rate results with quasi-static data, the strain rate effect on the tensile stress–strain response of the 4330-V steel was determined. The 4330-V steel exhibits slight work-hardening behavior in tension and the tensile flow stress is significantly sensitive to strain rate.     

Hopkinson压杆实验技术的应用进展

SHPB实验装置是研究各类工程材料动态力学性能的最基本实验手段,它不仅可用于测量金属、高聚物等均匀性好、变形量较大材料的冲击压缩(拉伸、剪切、扭转)应力—应变关系,经改进后还可以用于测量质地软、波阻抗小的泡沫介质材料和质地脆、均匀性差的混凝土类材料的冲击压缩应力-应变关系。此外,SHPB实验装置因加载方式简单,加载波形易测易控制,还可以开展混凝土类材料的层裂强度研究,火工品、引信的安全性、可靠性检测,高G值加速度传感器的标定以及炸药材料的压剪起爆临界点的测定等。     

The Development of a High Rate Tensile Testing System for Micro Scaled Single Crystal Silicon Specimens

Structures have been built at micro scales with unique failure mechanisms that are not yet understood, in particular, under high-rate loading conditions. Consequently, microelectromechanical systems (MEMS) devices can suffer from inconsistent performance and insufficient reliability. This research aims to understand the failure mechanisms in micro-scaled specimens deforming at high rates. Single-crystal silicon (SCS) micro specimens that are 4 μm thick are subjected to tensile loading at an average strain rate of 92 s^?1 using a miniature Hopkinson tension bar. A capacitance displacement system and piezoelectric load cell are incorporated to directly measure the strain and stress of the silicon micro specimens. The average dynamic elastic modulus of the silicon micro specimens is measured to be 226.8?±?18.50 GPa and the average dynamic tensile strength of the silicon is measured to be 1.26?±?0.310 GPa. High-speed images show that extensive fragmentation of the specimens occurs during tensile failure.     

The investigation on dynamic fracture behavour of materials under compressive-shear combined stress waves

In this paper, an improved plate impact experimental technique is presented for studying dynamic fracture mechanism of materials, under the conditions that the impacting loading is provided by a single pulse and the loading time is in the sub-microsecond range. The impacting tests are carried out on the pressure-shear gas gun. The loading rate achieved is dK/dt∼10⁸ MPa m^1/2s⁻¹. With the elimination of influence of the specimen boundary, the plane strain state of a semi-infinite crack in an infinite elastic plate is used to simulate the deformation fields of crack tip. The single pulses are obtained by using the “momentum trap” technique. Therefore, the one-time actions of the single pulse are achieved by eradicating the stress waves reflected from the specimen boundary or diffracted from the crack surfaces. In the current study, some important phenomena have been observed. The special loading of the single pulse can bring about material damage around crack tip, and affect the material behavior, such as kinking and branching of the crack propagation. Failure mode transitions from mode I to mode II crack are observed under asymmetrical impact conditions. The mechanisms of the dynamic crack propagation are consistent with the damage failure model. The project supported by the National Natural Science Foundation of China (No. 19672066 and 18981180-4) and the Key Project of Chinese Academy of Sciences (No. KJ951-1-20)