Diazotized reagent for spectrophotometric determination of glyphosate pesticide in environmental and agricultural samples

A new sensitive spectrophotometric method for the determination of glyphosate herbicide in environmental and agricultural samples is developed. The reaction is based on diazotization followed by coupling of glyphosate with p-dimethyl amino benzaldehyde. The resulted complex absorption spectra was observed at λ_max = 420 nm. The effects of other metal ions and pesticides were also tested for selective determination of glyphosate. The analytical parameters were optimized and have been successfully applied for determination of glyphosate in various environmental samples such as soil, water and vegetables. This method has a lower limit detection of 6 μg of glyphosate. Beer's law is obeyed over the concentration range of 6.0 μg–24.0 μg glyphosate in 25 mL of the final solution at 420 nm. The standard deviation and relative standard deviation calculated are 0.0055 and 1.023, respectively. The molar absorptivity of the colored system is 1.91 × 10¹⁰ L mol^?1cm^?1 and Sandell's sensitivity is found 0.408 × 10^?5 μg cm^?2. The proposed method is simple, sensitive, highly reproducible and time saving as compare to those complicated time consuming methods.     

Simultaneous Determination of Cobalt and Nickel Using Morpholinedithiocarbamate (MDTC) as Reagent by First and Second Derivative Spectrophotometry

A selective and sensitive derivative method has been proposed for the simultaneous determination of trace amounts of Co(II) and Ni(II) with morpholinedithiocarbamate (MDTC) in the presence of sodium lauryl sulphate (SLS). The molar absorption coefficients of the 1:2 complex of Co(II) and Ni(II) at 326 nm and 322 nm are 2.248 × 10⁴ and 2.505 × 10⁴ L mol^?1 cm^?1 for zero order. The analytical sensitivity for the second derivative of Co(II) and Ni(II) complexes are 0.0044 μg mL^?1 and 0.0060 μg mL^?1. The developed derivative procedure, using the zero‐crossing technique, has been successfully applied for the analysis of Co(II) and Ni(II) simultaneously in different alloy samples.     

Spectrophotometric Determination of Palladium(II) with n-Hydroxy-N,N-Diphenylbenzamidine and 1 -(2-Pyridylazo)-2-Naphthol

A spectrophotometric method to determine palladium(II) at trace levels is based on the extraction of palladium(II) as a binary complex with N-hydroxy-N,N′-diphenylbenzamidine (HDPBA) in chloroform at pH 5.0 ± 0.2. The complex shows maximum absorbance at 400 nm with molar absorptivity 6.4 × 10³ L mol^?1 cm^?1. The sensitivity of the Pd(II)-HDPBA complex was enhanced by the addition of l-(2-pyridylazo)-2-naphthol (PAN). The green coloured complex shows maximum absorbance at 620 nm with molar absorptivity 1.58 × 10⁴ L mol^?1 cm^?1. Sandell's sensitivity and the detection limit of the method are 0.0067 μg cm^?2and 0.1 μg Pd(II) mL^?1, respectively. Most common metal ions associated with palladium metal do not interfere. The effects of various analytical parameters on the extraction of the metal are discussed.     

Determination of Labetalol Hydrochloride in Drug Formulations by Spectrophotometry

A validated, selective and sensitive spectrophotometric method has been developed for the determination of labetalol hydrochloride in commercial dosage forms. The method is based on the coupling reaction of positive diazonium ion of 4‐aminobenzenesulfonic acid with phenolate ion of labetalol to form a colored azo compound which absorbs maximally at 395 nm. Under the optimized experimental conditions, the color is stable up to 2 h and Beer's law is obeyed in the concentration range of 0.8–17.6 μg mL^?1 with a linear regression equation of A = 4.84 × 10^?4 + 7.864 × 10^?2 C and coefficient of correlation, r = 0.9999. The molar absorptivity and Sandell's sensitivity are found to be 2.874 × 10⁴ L mol^?1 cm^?1 and 0.013 μg cm^?2 per 0.001‐absorbance unit, respectively. The limits of detection and quantitation of the proposed method are 0.08 and 0.23 μg mL^?1, respectively. The intra‐day and inter‐day precision variation and accuracy of the proposed method is acceptable with low values of standard analytical error. The recovery results obtained by the proposed method in drug formulations are acceptable with mean percent recovery ± RSD of 99.97 ± 0.52 ‐ 100.03 ± 0.63%. The results of the proposed method compared with those of Bilal's spectrophotometric method indicated excellent agreement with acceptable true bias of all samples within ± 2.0%.     

Spectrophotometric Determination of Esomeprazole Magnesium in Commercial Tablets Using 5‐Sulfosalicylic Acid and N‐Bromosuccinimide

Two simple, sensitive and economical spectrophotometric methods have been developed for the determination of esomeprazole magnesium in commercial dosage forms. Method A is based on the reaction of esomeprazole magnesium with 5‐sulfosalicylic acid in methanol to form a yellow product, which absorbs maximally at 365 nm. Method B utilizes the reaction of esomeprazole magnesium with N‐bromosuccinimide in acetone‐chloroform medium to form α‐bromo derivative of the drug peaking at 380 nm. Under the optimized experimental conditions, Beer's law is obeyed in the concentration ranges of 2‐48 and 10‐100 μg mL^?1 with molar absorptivity of 2.11 × 10⁴ and 4.57 × 10⁴L mol^?1 cm^?1 for methods A and B, respectively. The limits of detection for methods A and B are 0.35 and 0.46 μg mL^?1, respectively. No interference was observed from excipients commonly present in tablet formulations. Methods A and B are successfully applied to the commercial tablets for the estimation of esomeprazole magnesium with good accuracy and precision. The results compare favorably with the reference spectrophotometric method indicating no significant difference between the methods compared.     

Spectrophotometric determination of microamounts of mercury(II) and sulfide ions in aqueous solution

Ammonium (2′,3′-dihydroxy pyridyl-4′-azo)benzene-4-arsonate (DHP-4A) provides a simple, rapid, and sensitive spectrophotometric microdetermination of mercury(II) in aqueous solution. The magenta colored 1:2 metal to ligand complex formed has a molecular extinction coefficient 6.25 × 10⁴ liters mol^?1 cm^?1 at the maximum absorption of 535 nm in highly alkaline medium. Beer's law is obeyed up to 3.8 ppm and Sandell's sensitivity (for an absorbance of 0.001) is 0.0032 μg of mercury(II)/cm². The mercury(II) complexed with DHP-4A has also been used in microdetermination of sulfide ions using ligand exchange reaction. The optimum concentration range of sulfide ions which can reproducibly be determined is 0.16-5.05 μg/10 ml and sensitivity of sulfide ions determination (for an absorbance 0.001) is 7.3 × 10^?4 μg/cm².     

Spectrophotometric Determination of Tetracyclines in Pure Form and in Pharmaceutical Preparations,by a Molybdenum Blue Method

Abstract

A new and sensitive spectrophotometric method has been developed for the determination of tetracyclines either in a pure form or in Pharmaceuticals, by a molybdenum blue method. The procedure is based on the observation that, in sulphuric acid medium, tetracyclines reduce ammonium molybdate to molybdenum blue, the absorbance of which is proportional to the amount of antibiotic present. The variables affecting development of the color have been investigated and the conditions optimized. Beer's law is obeyed for up to 20 μg/ml of tetracycline HCl and oxytetracycline HCl, 28 μg/ml of demeclocycline HCl, 18 μg/ml of chlortetracycline HCl, 32 μg/ml of doxycycline HCl and 40 μ/ml of rolitetracycline. Molar absorptivities (1 mol^?1 cm^?1) and Sandell's sensitivities (μ cm^?2 per 0.001 absorbance unit) are, respectively: tetracycline HCl 4.9×10⁴ and 0.0098, oxytetracycline HCl 5.4×10⁴ and 0.0092, demeclocycline HCl 1.6×10⁴ and 0.0313, chlortetracycline HCl 5.5×10⁴ and 0.0094, doxycycline HCl 3.4×10⁴ and 0.0141, rolitetracycline 2.7×10⁴ and 0.0195.     

Spectrophotometric Determination of Lead by Extraction of the Mixed-Metal Complex Pb(II)-Ca-Purpurin (1,2,4-Trihydroxyanthraquinone)

Abstract

Mixtures of Lead(II) and Ca(II) form with purpurin (P; 1,2,4-Trihydroxyanthraquinone) the mixed-metal-complex PbCaP₃, which is extracted with isobutyl methyl ketone (IBMK) at pH 7.8. The molar absorptivity of the complex is 2.8 × 10⁴ l.mol^?1.cm^?1 at 575 nm and its conditional extraction constant 2.5 × 10¹⁷ 1⁴.mole^?4. The use of this complex for the spectrophotometric determination of lead up to 40 μg has been investigated. The proposed procedure has been successfully applied to the analysis of this metal in different samples.     

Synthesis of New Reagent 2,6‐Diacetylpyridine Bis‐4‐Phenyl‐3‐Thiosemicarbazone (2,6‐DAPBPTSC): Selective,Sensitive and Extractive Spectrophotometric Determination of Co(II) in Vegetable,Soil, Pharmaceutical and Alloy Samples

New synthesized reagent 2,6‐diacetylpyridine bis‐4‐phenyl‐3‐thiosemicarbazone (2,6‐DAPBPTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a reddish brown colored complex with 2,6‐DAPBPTSC, which is extracted into isoamylalcohol, under optimum conditions. The maximum absorption of the isoamylalcohol extract is measured at 400 nm. Beer's law is applied in the range 0.6‐6.0 ppm of cobalt(II). The molar absorptivity and Sandell's sensitivity of the complex is calculated as 2.2 × 10⁴ L mol^?1 cm^?1 and 2.68 × 10^?3 μg cm^?2, respectively. An adequate linearity with a correlation coefficient value of 0.969 is obtained for the Co(II)‐2,6‐DAPBPTSC complex. The instability constant of the complex, calculated from Asmus' method is 3.75 × 10^?4 The precision and accuracy of the method is checked with calculation of relative standard deviation (n = 5), 0.388 and the detection limit a value is 0.0028 μg mL^?1. The method is successfully employed for the determination of cobalt(II) in real samples, such as vegetables, soil, water samples, standard alloy samples, and the performance of the present method was evaluated in terms of Student ‘t’ test and Variance ‘f’ test, which indicates the significance of the present method is an inter comparison of the experimental values, using atomic absorption spectrometer (AAS).     

Spectrophotometric determination of nitrite in polluted waters using 3-nitroaniline

Nitrite reacts with 3-nitroaniline in the presence of hydrochloric acid to form a diazonium cation, which is subsequently coupled with N-(1-naphtyl)ethylenediammonium chloride to form a stable purple azo dye. The method is suitable for the determination of 0.01–0.80 μg ml^?1 nitrite. The reactions are very fast and require no control of temperature. The observed molar absorptivity and Sandell's sensitivity of the azo dye are 4.9 × 10⁴ l mol^?1 cm^?1 and 9.4 × 10^?4 μg cm^?2, respectively. The method is free from most interferences. The method has been applied successfully to polluted river water.     

Extractive Determination of Vanadium in Fungi Samples

A new reagent system has been reported for the extractive separation and simultaneous spectrophotometric de termination of vanadium (V). The method is based on the formation of a water in soluble blue‐violet V(V) complex with N‐hydroxy‐N‐m‐tolyl‐N′‐phenylbenzamidine (HTPBA), and neutral surfactant Triton X‐100 into chloroform over an acidity range of 1.0–10.0 M acetic acid. The complex shows a broad absorption maximum at 570 nm, when measured against a chloroform blank. The λ_max (570 nm) of the complex and that of re agent (313 nm) are well separated, hence the excess of the reagent does not interfere in the spectrophotometric de termination of the metal. The molar absorptivity (?) of the complex is (4.74) × 10³ 1 mol^?1 cm^?1. The linearity of the calibration curve is followed between 0.5–12.0 μg mL^?1 with slope, intercept and correlation coefficient of 9.16× 10^?2, 4.5 × 10^?3 and 0.999, respectively. The detection limit of the method is 45 μgl^?1. The proposed re agent system provides significantly higher tolerance limit for iron (500 μg mL^?1) and also various metalions commonly associated with vanadium did not interfere. The method was applied for the deter mi nation of vanadium content of three samples i.e. Spirogyra, Puccinia and Riccia.     

Determination of manganese(VII) as 3,3′-Dianisole-4,4′-bis(3,5-diphenyltetrazolium chloride) complex and its application

A simple, rapid, selective and sensitive spectrophotometric method is described for the determination of trace amounts of manganese using Blue tetrazolium chloride as a chromogenic reagent. The method is based on the formation of ion-associate complex between manganese(VII) and the cation of ditetrazolium salt, having an absorption maximum at 255 nm. Beer’s law is obeyed in the range of 0.1–1.6 μg mL^?1. The molar absorptivity and Sandell’s sensitivity were found to be 4.97 × 10⁴ L mol^?1 cm^?1 and 1.11 × 10^?3 μg cm^?2, respectively. Limit of deterction is 6.86 ng mL^?1 Mn(VII) and limit of quantitation is 22.8 ng mL^?1 Mn(VII). Optimum reaction conditions were evaluated. The effect of interfering ions on the determination is described. The extraction, distribution and association constants, and the recovery factor have been calculated.     

A highly sensitive spectrophotometric determination of gallium with chromal blue G in the presence of cetyltrimethylammonium chloride

A new spectrophotometric method for the determination of gallium with chromal blue G in the presence of cetyltrimethylammonium chloride is described. The sensitivity of color reaction between gallium and chromal blue G is greatly increased by the sensitizing action of cetyltrimethylammonium chloride. The gallium complex has maximal absorbance at 662 nm and pH 6.2–6.8. Beer's law is obeyed over the range 0.04–0.6 ppm of gallium. The molar absorptivity of the complex is 1.44 × 10⁵ liters mol^?1 cm^?1 at 662 nm, and the spectrophotometric sensitivity is 4.8 × 10^?4 μg Ga cm^?2. The mole ratio of gallium and chromal blue G in the complex is estimated to be 1:4. The formation constant and effect of interfering ions are described.     

Extraction Spectrophotometric Determination of Vanadium in Industrial Waste Water

A new and simple extraction spectrophotometric method for the determination of vanadium(V) with KIO₄, N‐phenylbenzohydroxamic acid (PBHA) and crystal violet (CV), in industrial waste water samples is described. It is based on the extraction of mixed‐ligand complex V(V)‐IO₄^? ‐PBHA‐CV⁺ into chloroform solution over 2‐7 MHC1. The molar absorptivity of the complex is (7.20) × 10³1 mol^?1 cm^?1 at λ_max 535 nm. The detection limit of the method is 44 μg 1^?1 V. The linearity of the calibration curve is followed up to 6 μgmL^?1 in the organic solution with slope, intercept and correlation coefficient of 1.34 × 10^?1, 6.7 × 10^?3 and +0.99, respectively. This method enhances the sensitivity of the conventional PBHA method for the determination of vanadium, and is free from interferences of other metal ions commonly associated with vanadium. The method has been successfully tested for the determination of V in the industrial waste water samples.     

Extraction—Spectrophotometric determination of nickel with 2-hydroxy-1-naphthaldoxime

A method for the solvent extraction—spectrophotometric determination of nickel with 2-hydroxyl-1-naphthaldoxime (HNA) has been studied. The method is based upon the formation of a nickel—HNA complex which is extracted into chloroform from an aqueous solution of pH 5.8. The nickel—HNA complex in chloroform exhibits an absorption maximum at 410 nm with molar absorptivity of 8.1 × 10³ liters mol^?1 cm^?1. Beer's law is applicable in the range from 5 to 50 μg of nickel. The mole ratio of the complex and effect of interfering ions are described.     

Spectrophotometric Assay of Certain Aminoglycosides Using Cyanoacetamide

Abstract

A simple and sensitive ultraviolet spectrophotometric method has been devised for the determination of amikacin, kanamycin, neomycin and streptomycin in pure form and in some pharmaceutical preparations. The method depends on the nitrosation of the primary amino groups followed by reaction with cyanoacetamide in ammonia medium at 100°C for 30 min, The reaction products exhibit a characteristic absorption. maximum at 270 nm. Beer's law is obeyed within the concentration ranges 4–40 μg ml^?1 for amikacin, kanamycin and neomycin and 8–80 μg ml^?1 for streptomycin with apparent molar absorptivities of about 1.85 × 10⁴ for the first three compounds and 1.3×10⁴ 1. mole^?1.cm^?1 for streptomycin.     

Rapid spectrophotometric determination of ruthenium(III) with prochlorperazine maleate

A rapid, simple spectrophotometric method for the determination of μg amounts of ruthenium, based on the formation of a pink complex between the metal and prochlorperazine maleate (PCPM) in sulphuric or hydrochloric acid solution, is described. The complex has an absorption maximum at 530 nm and its molar absorptivity is 6.733·10³ l mol^?1 cm^?1. The sensitivity is 0.0151 μg Ru cm^?2 for log I_o/I = 0.001. Beer's law is valid over the range 0.2–10 μg Ru ml^?1 ; the optimal range for spectrophotometric determination is 0.8–8.0 μg Ru ml^?1. Job's method of continuous variation, the mole ratio method and the slope ratio method indicate a 1:1 composition for the complex. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions are reported.     

A rapid method for the spectrophotometric determination of palladium(II) and osmium(VIII)

Propionyl promazine phosphate is proposed as a new reagent for the rapid spectrophotometric determination of microgram amounts of Pd(II) and Os(VII). PPP instantaneously forms an orange-red 1:1 complex with Pd(II) in sodium acetate-hydrochloric acid buffer of pH 0.8 to 4.0 at room temperature. The reagent also forms an orange-red radical cation with Os(VIII) in 0.5 to 2.0 M hydrochloric acid. The Pd-PPP complex exhibits an absorption maximum at 490–500 nm with molar absorptivity of 7.1 × 10³ liter mol^?1 cm^?1. The Os-PPP radical cation has an absorption maximum at 505–515 nm with molar absorptivity of 2.21 × 10⁴ liters mol^?1 cm^?1. The Sandell sensitivity is 0.022 μg/cm² (Pd) and 0.008 μg/ cm² (Os). Beer's law is valid over the concentration range 0.2 to 21 ppm (Pd) and 0.2 to 4.2 ppm (Os). The proposed method offers the advantages of simplicity, rapidity, and without the need for heating or extraction. The reagent is used for the determination of Pd in the synthetic mixtures corresponding to Pd alloys used in jewelery and Os in osmiridium alloy.     

Spectrophotometric Determination of Diphenadione Via its Metal Complexes

Abstract

Spectrophotometric procedure is described for the quantitative determination of diphenadione [2-(diphenylacetyl)-1,3-indandione], based on direct spectrophotometric measurements of the absorbances of its iron (III), iron (II) and cobalt (II), metal complexes at 488 nm, 505 nm and (334 nm, 372 nm), respectively. The drug reacts with metals in the ratio of 3:1 and 2:1 for iron (III) and for both iron (II) and cobalt (II) respectively. The obtained complexes have apparent molar absorptivities of 1.48 × 10³ 1 mol^?1 cm^?1, 0.714 × 10³ 1 mol^?1cm^?1 and (1.70 × 10³ 1 mol^?1cm^?1, 1.93 × 10³ 1 mol^?1cm^?1) for iron (III), iron (II) and cobalt (II) complexes, respectively. The procedure is suggested for the determination of 51–400 μg.ml^?1 diphenadione via the iron (II) complex and 35–170 μg.ml^?1 diphenadione via both cobalt (II) and iron (III) complexes. The suggested procedure has accuracies of 99.79 ± 0.67%, 99.64 ± 0.37% and (100.09 ± 0.53%, 99.99 ± 0.42%) for the metal complexes of iron (III), iron (II) and cobalt (II), respectively.     

A Rapid,Simple, and Sensitive Spectrophotometric Determination of Traces of Vanadium (V) in Foodstuffs,Alloy Steels,and Pharmaceutical,Water, Soil,and Urine Samples

Abstract

A rapid, simple, sensitive, and selective spectrophotometric method is investigated for the determination of traces of vanadium (V) in foodstuffs, alloy steels, and pharmaceutical, water, soil, and urine samples in aqueous DMF medium. The metal ion forms a green colored complex with 2-hydroxy-3-methoxy benzaldehyde thiosemicarbazone (HMBATSC) in an acidic buffer of pH 6.0. The green colored solution, having an absorbance maximum at 380 nm, is stable for more than 72 hours. Beer's law is obeyed in the range of 0.051–2.037 µg ml^?1. The molar absorptivity and Sandell's sensitivity of the method are found as 2.75 × 10⁴ l mol^?1 cm^?1 and 0.0018 µg cm^?2, respectively. The green colored complex has 1:2 [V(V)-HMBATSC] stoichiometry. The stability constant of the complex is determined as 3.267 × 10¹¹ by Job's method. The optimum reaction conditions and other analytical parameters are studied. A sensitive and selective second-order derivative spectrophotometry has also been proposed for the determination of V(V). The interference of various cations and anions are studied. The present method is successfully applied to the determination of vanadium (V) in foodstuffs, alloy steels, and pharmaceutical, water, soil, and urine samples.