The interaction of CH<Subscript>3</Subscript>Cl,CH<Subscript>2</Subscript>Cl<Subscript>2</Subscript>, CHCl<Subscript>3</Subscript>, and CCl<Subscript>4</Subscript> with ozone on the surface of ice under stratospheric conditions

The interaction of ozone with chlorinated methanes adsorbed on a thin ice film was studied over the temperature range 77–292 K. Ozone was shown to oxidize chlorinated methanes starting with 210 K to produce chlorine oxides of various compositions. The products formed in the oxidation of chlorinated methanes with ozone over the temperature range 77–292 K were analyzed by IR Fourier transform spectroscopy. Along with carbon dioxide and water, chlorine oxides in high oxidation states were predominantly formed.     

镉离子响应性凝胶光子晶体传感膜的构建

将光子晶体与响应性水凝胶结合,采用“三明治”填充方法,以聚苯乙烯（PS）胶体晶体为模板,丙烯酰胺和烯丙基硫脲为单体制备得到一种对镉离子具有特异响应性的凝胶光子晶体传感膜,并对其进行了形貌表征和响应性研究。结果表明,该传感膜具有排列整齐的反蛋白石结构,可对不同浓度的Cd²⁺输出不同的光学信号。随着Cd²⁺浓度的增大,传感膜的Bragg衍射峰发生蓝移,并伴随有显著的颜色变化。在最优配比,适宜pH和离子强度条件下,衍射峰的最大位移值可达51.1 nm。在研究过程中发现其他干扰金属离子的存在不会影响传感膜对Cd²⁺的特异性响应,并且表现出了较快的响应速度。在多次循环实验中传感膜由于具备高度交联结构而表现出了良好的机械性和化学稳定性。该传感膜的构建为Cd²⁺的快速高效及裸眼可视检测提供了可能性。     

Development of an optical ammonia sensor based on polyaniline/epoxy resin (SU-8) composite

Polyaniline (PANI)/glycidyl ether of bisphenol A (SU-8) composite film is elaborated in order to detect ammonia gas. These composite films are characterized by ultraviolet-visible (UV-vis) spectroscopy, Fourier transformed infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The sensitivity to ammonia is measured by optical absorption changes. The ammonia sensing properties of PANI/SU-8 composite films are studied, and then are compared to pure PANI films elaborated by chemical way. Experimental results show that the PANI/SU-8 optical sensor has simultaneously a rapid response to ammonia gas and regenerates easily, that is advantageous compared to pure PANI films.     

石墨烯掺杂纳米氧化锌用于检测三乙胺的增强气敏性能

通过简单研磨实现固相反应的方法制备了纳米氧化锌材料,并利用石墨烯掺杂对氧化锌进行改性,研究了氧化锌材料的气敏性能。利用X射线衍射仪(XRD)、扫描电镜(SEM)、红外光谱仪(IR)对合成的样品进行了结构和形貌表征,考察了原料比例和石墨烯掺杂量对氧化锌形貌和气敏性能的影响。结果表明:合成的氧化锌均为纳米颗粒,随着柠檬酸量增加,得到许多有气孔的氧化锌;石墨烯掺杂后,均得到纳米颗粒的氧化锌;气体检测表明,石墨烯掺杂后的氧化锌,其最佳工作温度由400℃降为280℃,对三乙胺表现出较高的选择性;掺杂3%石墨烯的氧化锌对浓度为0.1 mmol/L三乙胺的响应值(S=Ra/Rg)达到18,是掺杂前的4倍。石墨烯掺杂纳米ZnO可作为检测三乙胺气体的新型传感材料。     

Enantioselective behaviour of ethylated γ-cyclodextrins as GC stationary phases for chlorinated pesticides and phase characterisation by HPLC

Summary Small composition changes can influence the enantiomeric selectivity of alkylated cyclodextrins used as stationary phase in high resolution gas chromatography. A method is presented for the characterisation of such cyclodextrins using high performance liquid chromatography combined with evaporative light scattering and mass spectrometric detection (atmospheric pressure chemical ionisation in the positive ion mode). The method was applied to different batches of octakis (2,3,6-tri-O-ethyl)-γ-cyclodextrins (TEG-CD). Some showed a very good enantiomer selectivity for chlorinated pesticides. Separation evaluations were carried out with an improved test mixture containing selected, partly enantiomer enriched pesticides. Capillaries based on underethylated TEG-CD with up to 4 free OH groups dissolved in OV 1701-OH allowed the separation of α-HCH, o,p’-DDT, compounds of technical chlordane (cis-and trans-chlordane, U82, MC5, MC7, MC8) as well as chlordane metabolites (cis- and trans-heptachlor epoxide, oxychlordane) into enantiomers.     

Synthesis of polypyrrole films for the development of ammonia sensor

In the present investigation, we have synthesized a polypyrrole films by chemical polymerization technique for the development of ammonia sensor. The polypyrrole films were synthesized in an aqueous acidic medium on glass substrate with mild oxidation of ferric chloride at temperature 29°C. The concentrations (molar) of monomer (pyrrole), oxidant (ferric chloride), and dopant (polyvinyl sulfonate) have been optimized for the uniform and porous surface morphology of the synthesized polypyrrole film. The synthesized films were characterized by scanning electron microscopy, ultraviolet‐visible, and Fourier transforms infrared spectroscopy. Ammonia gas sensing behavior of polypyrrole films was studied by using indigenously developed gas sensing chamber. The synthesized polypyrrole film with optimized process parameters shows excellent and reproducible response to low concentration (100 ppm) of ammonia gas. Copyright © 2007 John Wiley & Sons, Ltd.     

On‐Chip Tailorability of Capacitive Gas Sensors Integrated with Metal–Organic Framework Films

Gas sensing technologies for smart cities require miniaturization, cost‐effectiveness, low power consumption, and outstanding sensitivity and selectivity. On‐chip, tailorable capacitive sensors integrated with metal–organic framework (MOF) films are presented, in which abundant coordinatively unsaturated metal sites are available for gas detection. The in situ growth of homogeneous Mg‐MOF‐74 films is realized with an appropriate metal‐to‐ligand ratio. The resultant sensors exhibit selective detection for benzene vapor and carbon dioxide (CO₂) at room temperature. Postsynthetic modification of Mg‐MOF‐74 films with ethylenediamine decreases sensitivity toward benzene but increases selectivity to CO₂. The reduced porosity and blocked open metal sites caused by amine coordination account for a deterioration in the sensing performance for benzene (by ca. 60 %). The enhanced sensitivity for CO₂ (by ca. 25 %) stems from a tailored amine–CO₂ interaction. This study demonstrates the feasibility of tuning gas sensing properties by adjusting MOF–analyte interactions, thereby offering new perspectives for the development of MOF‐based sensors.     

Analysis of urban particulate standard reference materials for the determination of chlorinated organic contaminants and additional chemical and physical properties

A previously issued National Institute of Standards and Technology (NIST) Standard Reference Material (SRM), SRM 1649, Urban Dust/Organics has been analyzed for chlorinated organic contaminants (polychlorinated biphenyls and chlorinated pesticides) to provide certified values for a new class of compounds relative to the former certification. The material will be reissued as SRM 1649a. Four different analytical techniques were used. Specifically, two different methods of extraction (Soxhlet and pressurized fluid extraction) were used in conjunction with sample analysis by gas chromatography with two different columns (5% phenyl-methyl polysiloxane and 50% methyl C-18 dimethyl polysiloxane) that exhibit distinct selectivity, and with two different modes of detection (electron capture detection and mass spectrometry). The results from these techniques were combined to generate certified concentrations for 35 PCB congeners (some in combination) and 8 chlorinated pesticides. Ancillary assessments of additional chemical and physical properties of SRM 1649a include homogeneity, moisture, total organic carbon, extractable mass, and the particle-size distribution. The approach and the results for the certification of the PCB congeners and chlorinated pesticides in SRM 1649a, and the determination of the additional chemical and physical properties are described. In addition, the determination of PCBs and chlorinated pesticides in SRM 1648, Urban Particulate Matter (a particulate material certified for inorganic constituents), is also discussed although certified values are not presented. Received: 8 June 1998 / Revised: 4 September 1998 / Accepted: 26 September 1998     

Analysis of urban particulate standard reference materials for the determination of chlorinated organic contaminants and additional chemical and physical properties

A previously issued National Institute of Standards and Technology (NIST) Standard Reference Material (SRM), SRM 1649, Urban Dust/Organics has been analyzed for chlorinated organic contaminants (polychlorinated biphenyls and chlorinated pesticides) to provide certified values for a new class of compounds relative to the former certification. The material will be reissued as SRM 1649a. Four different analytical techniques were used. Specifically, two different methods of extraction (Soxhlet and pressurized fluid extraction) were used in conjunction with sample analysis by gas chromatography with two different columns (5% phenyl-methyl polysiloxane and 50% methyl C-18 dimethyl polysiloxane) that exhibit distinct selectivity, and with two different modes of detection (electron capture detection and mass spectrometry). The results from these techniques were combined to generate certified concentrations for 35 PCB congeners (some in combination) and 8 chlorinated pesticides. Ancillary assessments of additional chemical and physical properties of SRM 1649a include homogeneity, moisture, total organic carbon, extractable mass, and the particle-size distribution. The approach and the results for the certification of the PCB congeners and chlorinated pesticides in SRM 1649a, and the determination of the additional chemical and physical properties are described. In addition, the determination of PCBs and chlorinated pesticides in SRM 1648, Urban Particulate Matter (a particulate material certified for inorganic constituents), is also discussed although certified values are not presented. Received: 8 June 1998 / Revised: 4 September 1998 / Accepted: 26 September 1998     

ZnO-SnO2纳米复合氧化物的制备、表征及其气敏性质的研究(英)

本文用可控湿化学共沉淀法研制了ZnO-SnO₂纳米晶体复合气敏材料并考察其对有毒气体CO和NO₂的气敏性质。用TEM、BET和XRD等方法表征了纳米复合物的粒度、形貌、比表面、热稳定性和相稳定性。研究了制备的可控参数，如金属阳离子总浓度、沉淀pH值和老化时间等对复合物气敏性质的影响。研究结果表明，该纳米复合氧化物具有化学均一性，高度热稳定和相稳定性，对CO和NO₂具有高的灵敏度和选择性，其气敏性质依赖于复合物组成、焙烧温度和操作温度。通过2wt％金属Cd的掺杂和10wt% Al2O3氧化物的表面包覆大大提高了气体的灵敏度和选择性。用程序升温吸脱附研究了纳米复合物表面对气体的吸脱附性能，并探讨了气敏机理。     

Metal-organic frameworks-derived hierarchical ZnO structures as efficient sensing materials for formaldehyde detection

Semiconducting metal oxides have been considered as effective approach for designing high-performance chemical sensing materials. In this paper, a kind of metal-organic frameworks ZIF-8 was used as sacrificed template to prepare porous ZnO hollow nanocubes for the application in gas sensing. It is found that changing calcination temperature and solvent can greatly influence the morphology of the material, which finally affects the gas sensing performance. Acetylene-sensing properties of the sensors were investigated in detail. It can be clearly seen that the material used methanol as reaction solvent with the decomposition at 350 °C for 2 h (ZnO-350-M) showed the optimal formaldehyde-sensing behaviors compared with other materials prepared in this experiment. The dynamic transients of the ZnO-350-M-based sensors demonstrated a high response value (about 10), fast response and recovery rate (4 s and 4 s, respectively) and good selectivity towards 100 ppm (part per million) formaldehyde as well as a low detectable limit (1 ppm). As exemplified for the sensing investigation towards formaldehyde, the porous ZnO hollow nanocubes showed a significantly improved chemical sensitivity due to the highly synergistic effects from the well exposed surfaces, defect states and the robust ZnO.     

二氧化锡中空微球用于快速灵敏检测硫化氢

以氨基酚醛树脂球作模板,通过一种简单的模板法制备了具有中空微球(HMS)结构的二氧化锡;将其涂覆于氧化铝陶瓷管金电极表面,制得一种新型薄膜式硫化氢传感器.采用X射线衍射(XRD)及透射电子显微镜(TEM)表征了材料的微观结构和形貌,并考察了二氧化锡中空微球(Sn O2HMS)的气敏性能.结果表明,二氧化锡中空微球对硫化氢气体表现出良好的气敏特性.在最佳工作温度(200℃)下,所制作的传感器对142.6 mg/m3硫化氢的响应值高达97.13%,响应时间为22 s.该传感器对硫化氢的响应线性范围为0.2852~142.6 mg/m3,相关系数为0.9931,检出限达到0.1549 mg/m3,且几乎不受环境湿度和温度的影响,具有良好的重现性和选择性.对养殖场中硫化氢气体连续监测10个月后,传感器响应信号衰减了5.4%,表明该传感器具有长期稳定的使用寿命,可实现远程监测的实际应用.     

Structural,morphological, optical and sensing properties of SnSe and SnSe2 thin films as a gas sensing material

In this work, orthorhombic tin selenide thin films were grown onto three different substrates using an organophosphorus precursor (Ph₃PSe) via chemical vapor deposition. Structural, microstructural and morphological properties of the as-grown films were systematically investigated using XRD, ESEM and AFM respectively. Grain size, microstrain and dislocation were calculated and correlated with different factors. The effects of selenization temperature and substrate type on different film properties and gas sensing response of films deposited onto alumina substrates were investigated. XRD analysis reveals the appearance of a mixed phase as a function of temperature. Furthermore, substrate type plays a key role in the rate of appearance of each phase. EDAX analysis confirms the existence of the desired elements and detect the evaporation of selenium and the appearance of oxygen at higher temperatures. Atomic force microscopy (AFM) was used to investigate the surface topography of the grown thin films.Optical properties of the films grown onto glass and silicon substrates were studied. From the recorded optical data, a direct optical band gap in the range of 0.9–1.3 eV was obtained with an absorption coefficient α > 10⁴ cm⁻¹ throughout large spectral regions. Optical studies were remarkably affected by the obtained phase as well as the selenization temperature. Gas sensing properties of the samples deposited onto alumina substrates were examined as a new sensing material for detection of methane gas at different concentrations. SnSe sensors show high sensitivity, are reversible and exhibit fast response and recovery times compared to SnSe₂ sensors.     

HFIP-Functionalized Co3O4 Micro-Nano-Octahedra/rGO as a Double-Layer Sensing Material for Chemical Warfare Agents

Semiconductor metal oxides (SMO)-based gas-sensing materials suffer from insufficient detection of a specific target gas. Reliable selectivity, high sensitivity, and rapid response–recovery times under various working conditions are the main requirements for optimal gas sensors. Chemical warfare agents (CWA) such as sarin are fatal inhibitors of acetylcholinesterase in the nerve system. So, sensing materials with high sensitivity and selectivity toward CWA are urgently needed. Herein, micro-nano octahedral Co₃O₄ functionalized with hexafluoroisopropanol (HFIP) were deposited on a layer of reduced graphene oxide (rGO) as a double-layer sensing materials. The Co₃O₄ micro-nano octahedra were synthesized by direct growth from electrospun fiber templates calcined in ambient air. The double-layer rGO/Co₃O₄-HFIP sensing materials presented high selectivity toward DMMP (sarin agent simulant, dimethyl methyl phosphonate) versus rGO/Co₃O₄ and Co₃O₄ sensors after the exposure to various gases owing to hydrogen bonding between the DMMP molecules and Co₃O₄-HFIP. The rGO/Co₃O₄-HFIP sensors showed high stability with a response signal around 11.8 toward 0.5 ppm DMMP at 125 °C, and more than 75 % of the initial response was maintained under a saturated humid environment (85 % relative humidity). These results prove that these double-layer inorganic–organic composite sensing materials are excellent candidates to serve as optimal gas-sensing materials.     

Analysis of gaseous toxic industrial compounds and chemical warfare agent simulants by atmospheric pressure ionization mass spectrometry

The suitability of atmospheric pressure chemical ionization mass spectrometry as sensing instrumentation for the real-time monitoring of low levels of toxic compounds is assessed, especially with respect to public safety applications. Gaseous samples of nine toxic industrial compounds, NH3, H2S, Cl2, CS2, SO2, C2H4O, HBr, C6H6 and AsH3, and two chemical warfare agent simulants, dimethyl methylphosphonate (DMMP) and methyl salicylate (MeS), were studied. API-MS proves highly suited to this application, with speedy analysis times (<30 seconds), high sensitivity, high selectivity towards analytes, good precision, dynamic range and accuracy. Tandem MS methods were implemented in selected cases for improved selectivity, sensitivity, and limits of detection. Limits of detection in the parts-per-billion and parts-per-trillion range were achieved for this set of analytes. In all cases detection limits were well below the compounds' permissible exposure limits (PELs), even in the presence of added complex mixtures of alkanes. Linear responses, up to several orders of magnitude, were obtained over the concentration ranges studied (sub-ppb to ppm), with relative standard deviations less than 3%, regardless of the presence of alkane interferents. Receiver operating characteristic (ROC) curves are presented to show the performance trade-off between sensitivity, probability of correct detection, and false positive rate. A dynamic sample preparation system for the production of gas phase analyte concentrations ranging from 100 pptr to 100 ppm and capable of admixing gaseous matrix compounds and control of relative humidity and temperature is also described.     

Monolayer Co3O4 Inverse Opals as Multifunctional Sensors for Volatile Organic Compounds

Monolayers of periodic porous Co₃O₄ inverse opal (IO) thin films for gas‐sensor applications were prepared by transferring cobalt‐solution‐dipped polystyrene (PS) monolayers onto sensor substrates and subsequent removal of the PS template by heat treatment. Monolayer Co₃O₄ IO thin films having periodic pores (d≈500 nm) showed a high response of 112.9 to 5 ppm C₂H₅OH at 200 °C with low cross‐responses to other interfering gases. Moreover, the selective detection of xylene and methyl benzenes (xylene+toluene) could be achieved simply by tuning the sensor temperature to 250 and 275 °C, respectively, so that multiple gases can be detected with a single chemiresistor. Unprecedentedly high ethanol response and temperature‐modulated control of selectivity with respect to ethanol, xylene, and methyl benzenes were attributed to the highly chemiresistive IO nanoarchitecture and to the tuned catalytic promotion of different gas‐sensing reactions, respectively. These well‐ordered porous nanostructures could have potential in the field of high‐performance gas sensors based on p‐type oxide semiconductors.     

Gas chromatographic sensing on an optical fiber by mode-filtered light detection

A chemical sensor for gas phase measurements is reported which combines the principles of chemical separation and fiber optic detection. The analyzer incorporates an annular column Chromatographic sensor, constructed by inserting a polymer-clad optical fiber into a silica capillary. Light from a helium-neon laser is launched down the fiber, producing a steady intensity distribution within the fiber, but a low background of scattered light. When sample vapor is introduced to the sensor, and an analyte-rich volume interacts with the polymer cladding, Chromatographic retention is observed simultaneously with a change in the local refractive index of the cladding. An increase in cladding refractive index (RI) causes light to be coupled out of the fiber, with detection at a right-angle to the annular column length to provide optimum S/N ratio. This detection mechanism is called mode-filtered light detection. We report a gas Chromatographic separation on a 3.1 m annular column (320 microm i.d. silica tube, 228 microm o.d. fiber with a 12 microm fluorinated silicone clad) of methane, benzene, butanone and chlorobenzene in 6 min. The annular column length was reduced to 22 cm to function as a sensor, with selected organic vapors exhibiting unique retention times and detection selectivity. The detection selectivity is determined by the analyte RI and the partition coefficient into the cladding. The calculated limit of detection (LOD) for benzene vapor is 0.03% by volume in nitrogen, and several chlorinated species had LOD values less than 1%. For binary mixtures of organic vapors, the detected response appears to be the linear combination of the two organic standards, suggesting that the annular column may be useful as a general approach for designing chemical sensors that incorporate separation and optical detection principles simultaneously.     

Porous sol gel silica films doped with crystalline NiO nanoparticles for gas sensing applications

A reliable sol gel route to synthesize NiO doped SiO₂ films with different NiO content is here described. The films showed detectable and reversible changes in both optical and electrical properties when exposed to some reducing/oxidizing gaseous species at temperatures in the 250°C–350°C range. A functional characterization protocol has been designed and some of the sensing properties of the materials have been investigated for detecting NO₂, CH₄, CO and H₂. An optical transmittance increase up to 2% has been detected for 1% CO in dry air atmospheres, while relative resistance response (R _R = R _gas/R _air) values up to 4.97 for 850 ppm H₂/air mixtures have been registered for conductometric gas sensing. Films at all NiO molar concentrations in the 10% NiO - 40% range showed an optical response to the target gas, while only 30% and 40% NiO films provided a detectable gas induced resistance change.     

Viscometric and volumetric studies on binary mixtures of 1,2-dichloroethane and chlorinated methanes or their binary equimolar mixtures at 303.15 K

Excess viscosities, η^E and molar excess volumes V^E were obtained for binary mixtures of 1,2-dichloroethane and chlorinated methanes and for pseudobinary mixtures of 1,2-dichloroethane and equimolar binary mixtures from chlorinated methanes at 303.15 K. The chlorinated methanes include carbon tetrachloride, chloroform and dichloromethane. Grunberg—Nissan interaction parameter d and interaction energy for flow of activation W_vis were also presented. The relationship between the η^E's and the V^E's has been quantitively considered using Singh's equations. The excess viscosities for all the systems are negative over the entire compositions. There are specific interactions between 1,2-dichloroethane and chlorinated methanes, but the specific interactions are not strong. The interactions of 1,2-dichloroethane with chlorinated methanes decrease in the order: chloroform > dichloromethane > carbon tetrachloride. ‘Pseudochloroform’ has been defined by us for the first time as the equimolar mixture of dichloromethane and carbon tetrachloride.     

Theoretical limit of energy consumption for removal of organic contaminants in U.S. EPA Priority Pollutant List by NRTL,UNIQUAC and Wilson models

This paper quantifies the theoretical limit of energy consumption for the removal of 20 representative organic contaminants (9 chlorinated alkyl hydrocarbons, 3 chlorinated alkenes, 3 brominated methanes, 5 aromatic hydrocarbons and their derivatives) in the United States Environmental Protection Agency (U.S. EPA) Priority Pollutant List by physical procedures. The general rules of the theoretical limit of energy consumption with different initial concentrations at 298.15 K and 1.01325 × 10⁵ Pa by NRTL, UNIQUAC and Wilson models are obtained from the thermodynamic analysis with our previously established method based on the thermodynamic first and second law. The results show that the waste treatment process needs a high energy consumption and the theoretical limit of energy consumption for organic contaminant removal increases with decreasing initial concentrations in aqueous solutions. The theoretical limit of energy consumption decreases with the more C–H bonds being replaced by C–Cl or C–Br bonds in chlorinated methanes, ethanes, ethenes or brominated methanes except for 1,1,2,2-tetrachloroethane, and the energy consumption for the removal of chlorinated methanes is higher than that of chlorinated ethanes with the same C–H bonds being replaced by C–Cl bonds. For the removal of chlorinated ethenes, brominated methanes and benzene and its derivatives studied, the energy consumption has corresponding relationship with solubility and the energy consumption is higher for the removal of organics with higher solubility.