Concentration conditions of formation of electrically conducting coatings from colloid-graphite dispersions

Concentration conditions under which electrically conducting graphite coatings can be formed on cardboard and polymeric dielectric substrates by deposition of graphite particles from colloid graphite dispersions were studied. It was found how the surface resistance of the samples varies, in the dc mode and in the microwave range, with the concentration and time conditions of formation of electrically conducting coatings. The transmittance and reflectance to microwave electromagnetic radiation were measured for samples coated with particles of colloid graphite from suspensions with various particle sizes.     

Template-free enzymatic synthesis of electrically conducting polyaniline using soybean peroxidase

Synthesis of polyaniline (PANI) catalyzed by soybean peroxidase at 1 °C in either aqueous or partially organic media, was studied as a function of pH and reaction media. Kinetic studies indicated that, unlike chemical polymerization, enzymatic polymerization of aniline showed neither induction period nor auto acceleration. The redox reversibility and chemical structure of the synthesized PANI was strongly dependent on the starting pH of the reaction medium. UV-vis, FT-IR, WAXD and TGA analysis are used to explain how the enzymatic reaction conditions influence both the chemical structure and physical properties of the PANI. Optimal reaction conditions are outlined for the direct enzymatic synthesis of electrically conductive emeraldine salt with yield as high as 71%.     

Synthesis of a new electrically conducting nanosized Ag–polyaniline–silica complex using γ-radiolysis and its biosensing application

In this study, a new electrically conducting nanosized Ag–PANI–silica complex, in which nano-silver is bound to silica and polyaniline (PANI), has been synthesized by using γ-irradiation at room temperature and not by using polyvinylpyrrolidone (PVP) as a colloidal stabilizer. The conductivity of nanosized Ag–PANI–silica complex was determined by using the Van der PauW method, and the complex turned out to have a high semi-conductivity (200 S/cm). The optical property and morphology were characterized by using a UV–vis spectrophotometer, field emission-scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The optical absorption bands of UV–vis analysis revealed a peak at 262, 368, and a slowly decreasing band at 600–800 nm originating from the a nanosized Ag–PANI–silica complex. FE-SEM and TEM showed that the nanosized Ag–PANI–silica complex has a particle size ranging from 10 to 30 nm and high stability. The nano-complex prepared by γ-irradiation can be applicable to be used as biosensor materials.     

Immobilized polymeric stationary phases using metalized silica supports

Immobilized presynthesized polymers on porous metalized (zirconized or titanized) silica particles as new stationary phases with improved chemical stability for RP-HPLC are reviewed. The preparations using different polymers, such as poly(methyloctylsiloxane), poly(methyltetradecylsiloxane), and poly(butadiene), different immobilization steps (gamma radiation, thermal treatment, and microwave radiation), and the chromatographic performances of these phases for polar, apolar, acidic, and basic compounds are discussed. The stability of some of these stationary phases using alkaline mobile phases is also presented.     

Iontophoretic transdermal drug delivery system using a conducting polymeric membrane

This work investigated the application of a porous polyaniline (PANi) membrane as a conducting polymeric membrane as well as an electrode in an iontophoretic transdermal drug delivery (TDD) system. Model drugs studied were: caffeine (MW: 194.2), lidocaine HCl (MW: 270.8) and doxycycline HCl (MW: 480.1). The PANi membrane was first tested as a simple membrane between the donor and receptor solutions; it provided satisfactory permeation profiles; the observed flux values were well described by a simplified mass transport model. A mouse skin was then mounted beneath the PANi film; such a composite system also presented satisfactory permeation profiles. Iontophoretic TDD experiments were next performed using both Ag|AgCl electrodes and PANi|AgCl electrodes for comparison; a PANi anode replaced the Ag anode in the last set. For doxycycline HCl, the flux and the 24-h accumulation from the PANi|AgCl set were 94.4 ± 81.2 μg/cm² h and 2760 ± 3980 μg/cm², respectively; those from the Ag|AgCl set were zero. For lidocaine HCl, the flux and 10-h accumulation from the PANi|AgCl set were, respectively, 43 ± 15 μg/cm² h and 392 ± 130 μg/cm²; the corresponding values from the Ag|AgCl set were 48 ± 20 μg/cm² h and 348 ± 78 μg/cm². Porous polyaniline membrane appears to be capable of replacing the Ag part of Ag|AgCl electrode system; further such a membrane can exercise additional control over agent transport rate. Aqueous-organic partitioning system through the porous membrane of PANi was tested with this novel technique as well. Because of the rather low porosity of the synthesized PANi film, such a system did not yield a high permeation rate.     

Vibrational spectra of doped electrically conducting polyparaphenylenes

We have made band assignments in the IR spectra of polyphenylenes synthesized by three different methods: by dehydro addition of benzene in the presence of a heterogeneous catalytic system, oxidizing agent — Lewis acid; by anodic oxidation of benzene in a solution of supporting electrolyte; by anodic oxidation of benzene in the presence of a system of the Ziegler-Natta catalyst type. Based on analysis of the vibrational spectra, we have estimated the length of the conjugation chain in synthesized polyphenylenes. We propose a method for synthesis of polyphenylene with predominantly quinoidal structure of the monomeric units, having a longer conjugation chain and distinguished by a higher, more stable value of the electrical conductivity.L. V. Pisarzhevskii Institute of Physical Chemistry, Ukrainian Academy of Sciences, Kiev. Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 27, No. 5, pp. 599–605, September–October, 1991. Original article submitted May 30, 1990.     

Engineering of superhydrophobic silica microparticles and thin coatings on polymeric films by ultrasound irradiation

Superhydrophobic coatings are one of the recent hot topics in industrial applications as well as academic studies. The mimicking lotus leaves' superhydrophobic properties have been successfully transferred to real-life applications. However, the current preparation methods used to obtain superhydrophobic coatings are still complex, commonly are not transparent and/or not durable.In the present study, a new relatively simple way to prepare superhydrophobic coatings on polymeric films is described. First, superhydrophobic silica microparticles (MPs) were synthesized by fluorination of SiO₂ MPs produced by a modified Stöber method. Briefly, tetraethyl orthosilicate was polymerized in an ethanol/water continuous phase under basic conditions, and the resultant SiO₂ MPs were dispersed in heptane as a continuous phase and reacted with 1H,1H,2H,2H-perfluorododecyltrichlorosilane (FTS) to yield FTS-SiO₂ MPs, which were dried and dispersed in decane. Superhydrophobic thin coatings were then produced by a ‘throwing stones’ sonication technique and deposited onto polycarbonate, polypropylene, polyethylene, and polyurethane films. The coatings are durable, may be transparent, and exhibit self-cleaning properties for the specific practical applications. The MPs and coated polymeric films were characterized by dynamic light scattering, high-resolution scanning electron microscopy, water contact and sliding angle measurements, and infrared and x-ray photoelectron spectroscopy. This ultrasound-assisted coating process may be upscaled and applied to many polymeric films, for instance polymethyl methacrylate, polystyrene, and polyvinyl chloride. Various applications are envisaged, including but not limited to self-cleaning windows, anti-sticking of snow to antennas and windows, solar panels, roof tiles, agricultural applications, corrosion resistance, and anti-biofouling.     

Stability and degradation of some electrically conducting polymers

The oxidative degradation reactions of polyacetylene, prepared from a soluble precursor polymer, are described and compared with those of more common polymers and of polyacetylene prepared by the conventional method. Because the band structure of the π-electron system of the polymer allows the formation of charge-transfer complexes with oxygen, the initial process in the pristine polymer is oxygen doping, with increasing conductivity. This is followed by irreversible degradation which is much faster than that of polyolefins or polydienes and faster than that of the crystalline polymer. Doping to low levels with electron acceptors removes the electrons involved in oxygen doping and the polymer becomes much more stable in air. Doping to high levels leads to new instabilities as the polymer reacts slowly with its counter-ions. Studies of polypyrrole and polythiophene show that these polymers are much more stable than polyacetylene but still undergo degradation reactions. The general features of their degradation mechanisms are discussed.     

Separation of acetylcholinesterase inhibitors using polymeric surfactants in polyelectrolyte multilayer coatings

The main objective of this study is the use of polymeric surfactants in polyelectrolyte multilayer (PEM) coatings for the separation of the pharmaceutical substances acetylcholinesterase inhibitors (AChEIs). AChEIs are used for the treatment of Alzheimer's Disease and Myasthenia Gravis. In the open-tubular capillary electrochromatography (OT-CEC) mode, the PEM coating is evaluated using nine AChEIs. Optimal conditions are established by altering several experimental parameters such as the pH of the background electrolyte (BGE), the anionic polymer for the PEM coating, the concentration of NaCl, which is used as an additive in the polymer deposition solutions, the number of bilayers, the deposition time, and the concentration of the polymeric surfactant. 25 mM NaH(2)PO(4).H(2)Ο and 25 mM Na(2)HPO(4) at pH 7 is used as BGE. Two bilayers of poly(diallyl dimethyl ammonium chloride) and poly(sodium N-undecanoyl L-leucinate) provide a baseline separation of all nine analytes in less than 4.5 min. Run-to-run reproducibility studies are also performed, and the relative standard deviation values of the migration times of the nine-analyte peaks are less than 2%. In addition, day-to-day, week-to-week and capillary-to-capillary reproducibilities are evaluated, and the relative standard deviation values of the electroosmotic flow are less than 2%. Finally, using the PEM coating approach, we were able to perform more than 150 runs in the same column. Neither the addition of the polymeric surfactant to the mobile phase, nor the reconstruction of the coating was necessary.     

Outstanding covalent conjugated gels: electrically conducting rubbers

Four series of fully conjugated poly(octylthiophene) gels were prepared by oxidative copolymerization of octylthiophene with four different cross-links (trithienylbenzenes) of functionalities f=3 or 6 and by varying the cross-link ratio R. The gels exhibit rubber elasticity and swell in apolar solvents. The gel fraction, the swelling ratio Q, the elastic modulus, and a NMR structural parameter display master curves of variations versus the variable fR, which characterises the statistical structure of the gels. This result shows that the linear chain segments comprised between adjacent cross-links govern the deformation properties of the networks. Transport properties were explored. The gels are photoluminescent. When doped (oxidation by iodine), they are electronically conducting both in dry and swollen states. At large Q intra-chain hopping mechanisms govern the conductivity while at small Q, intermolecular hopping processes are predominant. Cross-links are not a limitation to conductivity.     

ESR and magnetic properties of electrically conducting metallophthalocyanine polymers

Polymeric metallophthalocyanines of Cu, Ni, Co in which benzene rings are shared in common with the macrocyclic phthalocyanine rings containing peripheral carboxylic groups have been synthesized and their electrical conductivities are shown to increase from 5 to 8 orders of magnitude by thermal treatment. The cobalt polymer exhibits greater conductivity than its nickel or copper analogs. The heated polymers show very broad electron spin resonance (ESR) signals and large paramagnetic susceptibilities. The bulk magnetic susceptibility of these polymers shows Curie-like behavior when the samples are heated from room temperature to 473 K. This is explained on the basis of coexistence of fixed mobile and conduction electron spins in the system and the interaction of the soliton type defects present in these polymers with the polymeric network to give dipolar charge carriers. This is also supported by the decrease in ESR intensity with increasing temperature when the samples are heated in the ESR cavity. The effect of the presence of unpaired electrons on the d shell of the central metal atoms on the line width and the line shape of the ESR spectra is also explained. © 1994 John Wiley & Sons, Inc.     

Fabrication of anisotropic silica hollow microspheres using polymeric protrusion particles as templates

Anisotropic polystyrene/poly(styrene-co-divinylbenzene) (PS/P(S-DVB)) protrusion particles with various morphologies such as eyeball-like, snowman-like, and raspberry-like were synthesized using a modified seeded polymerization method by dynamically controlling and stabilizing the phase separation. The effects of swelling agent, crosslinker, and monomer concentrations on the particle morphologies were studied. Using the PS/P(S-DVB) protrusion particles as templates, anisotropic silica (SiO₂) hollow microspheres were fabricated facilely. The obtained anisotropic silica hollow spheres had a potential application in rapid waste removal and detoxification extraction with a very simple procedure.     

Thick silica gel coatings on methylsilsesquioxane monoliths using anisotropic phase separation

Silica gel coatings on methyltrimethoxysilane (MTMS)-derived monoliths have been studied using wetting transition. Wetting transition is observed in a small confined space, where a coating solution phase-separates into a well-coarsened dimension, making all the phase-separating polymerizing silica phase dynamically flow onto the existing surface of a mold. Bulk coating experiments have shown reductions of both macropore volume and diameter due to the coated layer. Comparing HPLC efficiencies of the coated monolith with those of the non-coated MTMS monolith revealed that the retention factors drastically increased in both normal- and reversed-phase modes. This is attributed to the existence of considerable amounts of accessible micropores left inside the coated layer, where analyte molecules travel and adsorb for a considerable period of time.     

Sponge-like nanostructured conducting polymers for electrically controlled drug release

An electrically controlled drug release (ECDR) system based on sponge-like nanostructured conducting polymer (CP) polypyrrole (PPy) film was developed. The nanostructured PPy film was composed of template-synthesized nanoporous PPy covered with a thin protective PPy layer. The proposed controlled release system can load drug molecules in the polymer backbones and inside the nanoholes respectively. Electrical stimulation can release drugs from both the polymer backbones and the nanoholes, which significantly improves the drug load and release efficiency. Furthermore, with one drug incorporated in the polymer backbone during electrochemical polymerization, the nanoholes inside the polymer can act as containers to store a different drug, and simultaneous electrically triggered release of different drugs can be realized with this system.     

Strategies for molecular designing of novel low-band-gap electrically conducting polymers

Molecular designing of low-band-gap electrically conducting polymers continues to be a major challenge of the field of electrically conducting polymers. Such polymers are expected to show not only good intrinsic conductivity but also possibly a good transparency in the visible spectrum for their use as infrared sensors/detectors. Low-band-gap polymers can also be of great interest as new polymeric materials for nonlinear optics. Various routes presently followed to achieve this designing with special reference to the donor-acceptor polymers and important results obtained with this route are briefly reviewed.     

Determination of water pollutants by direct-immersion solid-phase microextraction using polymeric ionic liquid coatings

The determination of a group of eighteen pollutants in waters, including polycyclic aromatic hydrocarbons and substituted phenols, is conducted in direct-immersion solid-phase microextraction (SPME) using the polymeric ionic liquid (PIL) poly(1-vinyl-3-hexadecylimidazolium) bis[(trifluoromethyl)sulfonyl]imide as a novel coating material. The performance of the PIL fiber coating in the developed IL-SPME-gas chromatography (GC)–mass spectrometry (MS) method is characterized by average relative recoveries of 92.5% for deionized waters and 90.8% for well waters, average precision values (as relative standard deviations, RSD%) of 11% for deionized waters and 12% for well waters, using a spiked level of 5 ng mL⁻¹. The detection limits oscillate from 0.005 ng mL⁻¹ for fluoranthene to 4.4 ng mL⁻¹ for 4-chloro-3-methylphenol, when using an extraction time of 60 min with 20 mL of aqueous sample. The extraction capabilities of the PIL fiber have been compared with the commercial SPME coatings: polydimethylsyloxane (PDMS) 30 μm, PDMS 100 μm and polyacrylate (PA) 85 μm. The PIL fiber is superior to the PDMS 30 μm for all analytes studied. A qualitative study was also carried out to compare among the nature of the coating materials by normalizing the coating thickness. The PIL material was shown to be more efficient than the PDMS material for all analytes studied. The PIL coating was also adequate for nonpolar analytes whereas the PA material was more sensitive for polar compounds.     

基于碳纳米管和导电聚合物电刺激释放地塞米松导电生物膜的制备

为了降低植入式神经电极引起的炎性组织反应,通过层叠法构建可电刺激释放抗炎药物地塞米松的碳纳米管与聚吡咯双层导电生物膜(MWCNTs/Dex@PPy/Dex).并采用场发射扫描电镜(FESEM)、傅里叶变换红外光谱(FT-IR)、紫外分光光度法(UV)、循环伏安扫描(CV)和交流阻抗(EIS)对生物膜表面形貌、成分组成、...     

Comparison of model monomeric and polymeric alkyl stationary phases on silica using sum-frequency spectroscopy

Model monomeric and polymeric stationary phases were examined using sum-frequency spectroscopy and contact angle measurements in order to determine structural differences between the two stationary phases. Octadecyldimethylchlorosiloxane (ODMS) monolayers and ODMS/methyl siloxane (MS) mixed monolayers in contact with water and acetonitrile solvent were examined. The results showed that the alkyl chains in the ODMS and the ODMS/TMS monolayer are highly disordered and are weakly sensitive to the change in solvent environment. In order to determine whether the observed disorder in ODMS is due to steric effects of the silicon bonded methyl groups or the lack of crosslinking, "surface-bonded" ODS and "highly crosslinked" ODS were studied and compared with ODMS. Calculations using contact angle data on ODMS monolayers showed that water interacts 70% with methyl groups and 30% with methylene groups.     

Synthesis and characterization of electrically conducting polyaniline–TCNE complexes

Polyaniline–tetracyanoethylene (TCNE) complexes can be synthesized either from emeraldine base or emeraldine hydrochloride by a relatively simple method. The complexes demonstrate greater stability than the emeraldine hydrochloride at elevated temperatures and under high current densities. The electrical conductivity of the complexes synthesized from emeraldine base can be varied from < 10^?6 to 0.2 S/cm by varying the amount of TCNE incorporated. The complexes synthesized from emeraldine hydrochloride are slightly more conductive than the starting emeraldine hydrochloride. In both types of complexes, it appears that electron transfer between the polyaniline and TCNE has occurred resulting in the formation of some positively charged polyaniline nitrogen and TCNE anions.