Synthesis and bioactivity of highly ordered TiO2 nanotube arrays

The highly ordered TiO₂ nanotube arrays were fabricated by potentiostatic anodization of Ti foils in fluorinated dimethyl sulfoxide (DMSO). TiO₂ nanotube arrays are formed using a 40 V anodization potential for 24 h, with a length of 12 μm, diameter of 170 nm and aspect ration of about 70. The as-prepared nanotubes are amorphous, but can be crystallized as the heat treatment temperature increases. Anatase phase appears at a temperature of about 300 °C, then transforms to rutile phase at about 600 °C. After heat treatment at 500 °C and soaking in SBF for 14d, a thick apatite layer of about 13 μm covers the whole surface of TiO₂ nanotube arrays, indicating their excellent in vitro bioactivity, which is mainly attributed to their high specific surface area and the anatase phase.     

Photoelectrochemical property and photocatalytic activity of N-doped TiO2 nanotube arrays

N-doped TiO₂ nanotube arrays (NTN) were prepared by anodization and dip-calcination method. Hydrazine hydrate was used as nitrogen source. The surface morphology of samples was characterized by SEM. It showed that the mean size of inner diameter was 65 nm and wall thickness was 15 nm for NTN. The ordered TiO₂ nanotube arrays on Ti substrate can sustain the impact of doping process and post-heat treatment. The atomic ratio of N/Ti was 8/25, which was calculated by EDX. Photoelectrochemical property of NTN was examined by anodic photocurrent response. Results indicated the photocurrent of NTN was nearly twice as that of non-doped TiO₂ nanotube arrays (TN). Photocatalytic activity of NTN was investigated by degrading dye X-3B under visible light. As a result, 99% of X-3B was decomposed by NTN in 105 min, while that of TN was 59%.     

Ni-doped TiO2 nanotube arrays on shape memory alloy

Self-organized Ni-Ti-O nanotube arrays were fabricated through a direct anodization of NiTi shape memory alloy in glycerol-based electrolyte. The growth of Ni-doped TiO₂ nanotube arrays was mainly affected by anodization voltage and temperature. Higher anodization voltage facilitated the growth of uniform nanotube arrays. Large-area open-ended Ni-Ti-O nanotube arrays could form on the surface of the shape memory alloy under a higher anodization temperature. The oxide nanotubes had a gradually changed composition along the growth direction of the nanotube and presented a thermal stability up to 400 °C. The nanotubular oxide demonstrated a much better hydrophilic behavior than that of the traditional oxide layer grown on NiTi substrate through air oxidization. The successful fabrication of Ni-doped TiO₂ nanotube arrays here makes it feasible to further explore excellent physical and chemical as well as biomedical properties of the nanotube-modified surfaces of the NiTi shape memory alloy.     

Highly ordered anodic TiO2 nanotube arrays and their stabilities as photo(electro)catalysts

Highly ordered TiO₂ nanotube arrays with an average diameter of 230 nm, a wall thickness of 30 nm and a length of 1.8 μm were fabricated within a large domain by electrochemically anodizing of a titanium foil in a mixed solution of glycerol and NH₄F aqueous electrolyte. The TiO₂ nanotubes exhibit an anatase structure after annealing at 450 °C in air for 3 h. The direct photolysis (DP), photocatalytic (PC), electrocatalytic (EC) and photoelectrocatalytic (PEC) activities of the TiO₂ nanotube arrays were investigated using methyl orange (MO) as the model pollutant. The degradation of MO in PC process is faster than that in DP process, which confirms the photocatalysis of TiO₂ nanotube arrays. The degradation rate in PEC process is much higher than those in EC and PC processes, which demonstrates the synergetic effect between PC and EC processes. The synergetic factor is 4.1, which suggests that the synergetic effect is strong. Moreover, the stabilities of morphology, structure and photo(electro)catalytic degradation performance of the TiO₂ nanotube arrays were studied in order to evaluate their applicability as photo(electro)catalysts. The photo(electro)catalytic experiments bring neither morphological nor structural modifications to the nanotube arrays. The photo(electro)catalytic degradation rates of the TiO₂ nanotube arrays maintain stable in 10 cycles, which indicates that the TiO₂ nanotube arrays are appropriate to be applied as photo(electro)catalysts.     

Fabrication, characterization and photoelectrochemical properties of Fe2O3 modified TiO2 nanotube arrays

TiO₂ nanotube (NT) arrays modified by Fe₂O₃ with high sensibility in the visible spectrum were first prepared by annealing anodic titania NTs pre-loaded with Fe(OH)₃ which was uniformly clung to the titania NTs using sequential chemical bath deposition (S-CBD). The photoelectrochemical performances of the as-prepared composite nanotubes were determined by measuring the photo-generated currents and voltages under illumination of UV-vis light. The titania NTs modified by Fe₂O₃ showed higher photopotential and photocurrent values than those of unmodified titania NTs. The enhanced photoelectrochemical behaviors can be attributed to the modified Fe₂O₃ which increases the probability of charge-carrier separation and extends the range of the TiO₂ photoresponse from ultraviolet (UV) to visible region due to the low band gap of 2.2 eV of Fe₂O₃.     

Crystalline orientation preference for TiO2 nanotube arrays with efficient photoelectrochemical properties

Novel TiO₂ nanotube arrays (TiO₂ NTAs) with preferred oriented crystalline structure were firstly achieved by a facile method through anodizing Ti sheets with textured microstructure. Highly oriented crystalline structure of TiO₂ NTAs, with its (004) lattice plane of anatase TiO₂ paralleling to the top surface of TiO₂ NTAs was identified by the results of XRD, which was further confirmed by the regular diffraction spots and lattice fringes with uniform direction in HRTEM images. In comparison with normal randomly oriented TiO₂ NTAs, the quasi-single crystal structure of highly oriented TiO₂ NTAs can suppress the recombination of photogenerated electron–hole pairs and enhance the transfer of photocarriers, as was proved by the photoelectrochemical measurement conducted on both normal TiO₂ and oriented TiO₂ NTAs. The results of this study provide a promising avenue to obtain high photoelectrochemical performance TiO₂ NTAs-based hybrid nanomaterials.     

Optical and electrical characterization of TiO2 nanotube arrays on titanium substrate

Novel oriented aligned TiO₂ nanotube (TN) arrays were fabricated by anodizing titanium foil in 0.5% HF electrolyte solution. It is indicated that the sizes of the TNs greatly depended on the applied voltages to some extent. The electrical properties of the TN arrays were characterized by current-voltage (I-V) measurements. It exhibits a nonlinear, asymmetric I-V characterization, which can be explained that there exists an n-type semiconductor/metal Schottky barrier diode between TN arrays and titanium substrate interface. The absorption edges shift towards shorter wavelengths with the decrease of the anodizing voltages, which is attributed to the quantum size effects. At room temperature, a novel wide PL band consisting of four overlapped peaks was observed in the photoluminescence (PL) measurements of the TN arrays. Such peaks were proposed to be resulted from the direct transition X₁ → X₂/X₁, indirect transition Γ₁ → X₂/X₁, self-trapped excitons and oxygen vacancies, respectively.     

Influence of anodization parameters on the morphology of TiO2 nanotube arrays

TiO₂ nanotube arrays can be fabricated by electrochemical anodization in organic and inorganic electrolytes. Morphology of these nanotube arrays changes when anodization parameters such as applied voltage, type of electrolyte, time and temperature are varied. Nanotube arrays fabricated by anodization of commercial titanium in electrolytes containing NH₄F solution and either sulfuric or phosphoric acid were studied at room temperature; time of anodization was kept constant. Applied voltage, fluoride ion concentration, and acid concentrations were varied and their influences on TiO₂ nanotubes were investigated. The current density of anodizing was recorded by computer controlled digital multimeter. The surface morphology (top-view) of nanotube arrays were observed by SEM. The nanotube arrays in this study have inner diameters in range of 40-80 nm.     

Synthesis and field emission of diamond-like carbon nanorods on TiO2/Ti nanotube arrays

Highly ordered TiO₂/Ti nanotube arrays were fabricated by anodic oxidation method in 0.5 wt% HF. Using prepared TiO₂/Ti nanotube arrays deposited Ni nanoparticles as substrate, high quality diamond-like carbon nanorods (DLCNRs) were synthesized by a conventional method of chemical vapor deposition at 750 °C in nitrogen atmosphere. DLCNRs were analyzed by filed emission scanning electron microscopy and Raman spectrometer. It is very interesting that DLCNRs possess pagoda shape with the length of 3–10 μm. Raman spectra show two strong peaks about 1332 cm⁻¹ and 1598 cm⁻¹, indicating the formation of diamond-like carbon. The field emission measurements suggest that DLCNRs/TiO₂/Ti has excellent field emission properties, a low turn-on field about 3.0 V/μm, no evident decay at 3.4 mA/cm² in 480 min.     

Influence of long-term aqueous exposure on surface properties of plasma sprayed oxides Al2O3, TiO2 and their mixture Al2O3-13TiO2

The surface properties of plasma sprayed Al₂O₃- and TiO₂-based coating materials were characterized in order to investigate the influence of surface strain and phase inhomogenity. The materials were water exposed up to 8 months. The bulk crystallographic structure, dissolution behaviour, effective charge (zeta potential, isoelectric point), surface compositions and oxidation states were determined. In addition, the properties of the aging solutions, such as conductivity, supernatant pH (point of zero charge), and redox potential, were monitored during aging.It was shown that the materials were stable under aging conditions, but that considerable surface rearrangements, such as dissolution-reprecipitation and surface site redistributions may occur. However, overall only minor changes in surface properties results from this restructuring process.     

Applying the statistical experimental method to evaluate the process conditions of TiO2 nanotube arrays by anodization method

Vertically oriented TiO₂ nanotube arrays were successfully produced by the anodization technique in NH₄F/H₃PO₄ electrolyte. The structure and morphology were characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). It is found that TiO₂ nanotube arrays annealed at 500 °C containing 100% anatase phase and entirely converted into rutile at 800 °C. The response surface methodology (RSM) and Box-Behnken design were applied to find the optimal factor conditions in production of TiO₂ nanotube arrays. Based on the results in preliminary experiments, we selected anodization time, anodization voltage and NH₄F concentration as the key factors to investigate their effects on responses. The regression models were built by fitting the experimental results with a second-order polynomial. By using the regression models, the optimal factor conditions were obtained as follows: anodization time of 300 min; anodization voltage of 15.39 V; NH₄F concentration of 0.50 M. Corresponding to the optimal factor conditions, the predicted average length and diameter of nanotube array were 1429 nm and 33 nm, respectively. Confirmation experiments using the optimized conditions were performed: TiO₂ nanotube arrays were obtained with an average tube length of 1420 nm and average tube diameter of 36 nm. The experimental results are in good agreement with the predicted results.     

Favorable recycling photocatalyst TiO2/CFA: Effects of loading percent of TiO2 on the structural property and photocatalytic activity

A series of photocatalysts TiO₂/CFA were prepared using coal fly ash (CFA), waste discharged from coal-fired power plant, as substrate, and then these photocatalysts were characterized by scanning electron microscope, X-ray diffraction analysis, nitrogen adsorption test and ultraviolet-visible absorption analysis. The effects of loading percent of TiO₂ on the photocatalytic activity and re-use property of TiO₂/CFA were evaluated by the photocatalytic decoloration and mineralization of methyl orange solution. The results show that the pore volume and the specific surface area of the TiO₂/CFA both increased with the increase in the loading percent of TiO₂, which improved the photocatalytic activity of TiO₂/CFA. However, when the loading percent of TiO₂ was too high (up to 54.51%), superfluous TiO₂ was easy to break away from CFA in the course of water treatment, which was disadvantaged to the recycling property of TiO₂/CFA. In this study, the optimal loading percent of TiO₂ was 49.97%, and the efficiencies of photocatalytic decoloration and mineralization could be maintained above 99% and 90%, respectively, when the photocatalyst was used repeatedly, without any decline, even at the sixth cycle.     

Study on highly visible light active Bi-doped TiO2 composite hollow sphere

Bi-doped hollow titania spheres were prepared using carbon spheres as template and Bi-doped titania nanoparticles as building blocks. The Bi-doped titania nanoparticles were synthesized at low temperature. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The effects of Bi content on the physical structure and photocatalytic activity of doped hollow titania sphere samples were investigated. Results showed that there was an optimal Bi-doped content (4%) for the photocatalytic degradation of methylene blue (MB).     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

有序TiO2纳米管阵列结构的可控生长及其物相研究

分别在HF水溶液、含NH₄F和H₂O的乙二醇有机溶液中对Ti箔进行阳极氧化,得到TiO₂纳米管阵列结构.该结构高度有序、分布均匀、垂直取向,且通过阳极氧化工艺条件(如阳极氧化电压、电解液的选择与配比以及氧化时间等)可实现对其结构参数(如管径、管壁厚度、管密度、管长等)的有效控制.利用XRD研究了TiO₂纳米管阵列的物相结构.结果表明：退火前的TiO₂纳米管阵列为无定形结构;分别在真空和氧气氛中50 关键词： 2纳米管阵列')" href="#">TiO₂纳米管阵列 阳极氧化 可控生长     

Effects of impurities containing phosphorus on the surface properties and catalytic activity of TiO2 nanotube arrays

TiO₂ nanotube arrays were prepared by titanium anodic oxidation with either HF or H₃PO₄/NH₄F aqueous electrolyte solutions. The samples were characterized by means of X-ray diffraction (XRD), infrared spectroscopy (IR), Raman spectroscope, photoluminescence spectra (PL) and photocurrent response. Aqueous solutions of methylene blue or Cr(VI) ions were used as the target pollutants to compare catalytic activities of the two nanotube array types. The amorphous impurities containing phosphorus were confirmed by XRD and IR, for the sample synthesized with H₃PO₄/NH₄F electrolytes. They closed a portion of the active sites, acted as recombination centers of photo-generated charges, and were also involved in the negative reactions of competing photo-generated holes or OH radicals. The TiO₂ nanotube arrays formed in the H₃PO₄/NH₄F electrolytes exhibited a stronger fluorescence spectrum, a weaker photocurrent and a lower catalytic activity than the sample fabricated with HF electrolyte without phosphorus impurities.     

Mesoporous nanotube aggregates obtained from hydrothermally treating TiO2 with NaOH

Nanotube aggregates with high porosity were prepared from hydrothermal treatment of TiO₂ particles in NaOH at 130 °C, followed by HCl rinsing to different pH values. Pore structure of the aggregates, which were mainly mesoporous, was characterized by analyzing the N₂ sorption isotherm with different methods including the t-plot and density function theory. The surface area, pore volume and mean pore size of the aggregates increased with the rinsing acidity to reach a maximum (e.g. 400 m²/g in surface area) at pH 1.6 and then decreased with further increase of the acidity. The crystalline phase and composition of the aggregates were, as well, significantly affected by the acidity of the post-treatment rinsing. Large-surface area aggregates were of loosely-attached nanotubes, composed of both anatase TiO₂ and H₂Ti₂O₅·H₂O, obtained under a mildly acidic rinsing condition, while basic or highly acidic conditions resulted in the formation of closely coagulated dense structures consisting of different crystalline phases.     

Passivation of TiO2 by ultra-thin Al-oxide

The passivation of sol–gel TiO₂ by ultra-thin layers of Al-oxide has been investigated using transient and spectral photovoltage (PV) techniques. The ultra-thin layers of Al-oxide were prepared by the ion-layer gas reaction (ILGAR) technique and modified by thermal treatments in air, vacuum or Ar/H₂S atmosphere. The samples where characterized by elastic recoil detection analysis (ERDA), X-ray photoelectron spectroscopy (XPS), and contact potential difference (CPD) technique. Without an Al-oxide surface layer, electronic states in the forbidden gap of TiO₂ are formed during thermal treatments in vacuum and Ar/H₂S. The trap density is strongly reduced at the TiO₂/Al-oxide interface. The formation of electronic defects is prevented by a closed ultra-thin layer of Al-oxide.     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.     

含水量对TiO2纳米管形貌控制参数的影响

以不同含水量的乙二醇溶液为电解液,采用阳极氧化法制备TiO2纳米管阵列。通过记录反应过程中电导率、粘度及回路电流随时间的变化曲线,研究含水量对电解液粘度、电导率及电流等过程参数的影响,分析了纳米管形貌尺寸与TiO2溶蚀所耗电荷量的关系。粘度初始值和初始电导率均与含水量呈三次关系,相关系数分别为0.992 5和0.977 8。在反应过程中,溶液粘度值有缓慢增加的趋势。由于不同含水量的电解液粘度的不同,H+和OH-数量不同,F-迁移速率不同,电导率-时间曲线及电流-时间曲线具有不同的变化趋势,并对其进行了理论分析。当水体积分数为4%,5%,6%和10%时,纳米管的形貌较为有序并且TiO2纳米管阵列表面的碎片较少,纳米管直径变化范围为50 nm至72 nm,长度变化范围为0.85~1.90 m。F-腐蚀氧化膜时所消耗电量与TiO2氧化膜被腐蚀掉的体积呈一次函数关系,即腐蚀电量越大,腐蚀掉的体积越大,为制备一定形貌尺寸的纳米管提供了一定的控制方法。