Femtosecond laser-induced damage of gold films

Single- and multi-shot ablation thresholds of gold films in the thickness range of 31-1400 nm were determined employing a Ti:sapphire laser delivering pulses of 28 fs duration, 793 nm center wavelength at 1 kHz repetition rate. The gold layers were deposited on BK7 glass by an electron beam evaporation process and characterized by atomic force microscopy and ellipsometry. A linear dependence of the ablation threshold fluence F_th on the layer thickness d was found for d ≤ 180 nm. If a film thickness of about 180 nm was reached, the damage threshold remained constant at its bulk value. For different numbers of pulses per spot (N-on-1), bulk damage thresholds of ∼0.7 J cm⁻² (1-on-1), 0.5 J cm⁻² (10-on-1), 0.4 J cm⁻² (100-on-1), 0.25 J cm⁻² (1000-on-1), and 0.2 J cm⁻² (10000-on-1) were obtained experimentally indicating an incubation behavior. A characteristic layer thickness of L_c ≈ 180 nm can be defined which is a measure for the heat penetration depth within the electron gas before electron-phonon relaxation occurs. L_c is by more than an order of magnitude larger than the optical absorption length of α⁻¹ ≈ 12 nm at 793 nm wavelength.     

Femtosecond pulsed laser ablation of diamond-like carbon films on silicon

Femtosecond pulsed laser ablation (τ = 120 fs, λ = 800 nm, repetition rate = 1 kHz) of thin diamond-like carbon (DLC) films on silicon was conducted in air using a direct focusing technique for estimating ablation threshold and investigating the influence of ablation parameter on the morphological features of ablated regions. The single-pulse ablation threshold estimated by two different methods were ?_th(1) = 2.43 and 2.51 J/cm². The morphological changes were evaluated by means of scanning electron microscopy. A comparison with picosecond pulsed laser ablation shows lower threshold and reduced collateral thermal damage.     

Morphology of ablation craters generated by fs laser pulses in LiNbO3

The surface morphology of the ablation craters generated in LiNbO₃ by 130 fs laser pulses at 800 nm has been investigated by AFM/SNOM microscopy. The single pulse fluence corresponding to the ablation threshold has been estimated to be ≈1.8 J/cm².A complex structure including random cone-shaped protrusions is observed inside the ablated crater. The scale of the protrusion spacing is in the submicron range and the heights are typically of a few tens of nanometers. At and outside the crater rim a novel quasi-periodic wave-like topography pattern is observed in both types of microscopy techniques. The average wavelength, that is slightly dependent on pulse fluence, is (500-800 nm) comparable to the light wavelength. This novel topography feature keeps a close similarity with a Fresnel diffraction pattern by an absorbing circular obstacle or impact wave pattern produced by a combination of heat and shock wave (resemble that of impact crater). It is proposed that the obstacle is associated to the strongly nonlinear multiphoton absorption at the peak of the pulse profile. The energy deposited by nonlinear absorption of such profile causes ablation of both the crater and the rippled structure.     

Analyses of surface coloration on TiO2 film irradiated with excimer laser

TiO₂ film of around 850 nm in thickness was deposited on a soda-lime glass by PVD sputtering and irradiated using one pulse of krypton-fluorine (KrF) excimer laser (wavelength of 248 nm and pulse duration of 25 ns) with varying fluence. The color of the irradiated area became darker with increasing laser fluence. Irradiated surfaces were characterized using optical microscopy, scanning electron microscopy, Raman spectroscopy and atomic force microscopy. Surface undergoes thermal annealing at low laser fluence of 400 and 590 mJ/cm². Microcracks at medium laser fluence of 1000 mJ/cm² are attributed to surface melting and solidification. Hydrodynamic ablation is proposed to explain the formation of micropores and networks at higher laser fluence of 1100 and 1200 mJ/cm². The darkening effect is explained in terms of trapping of light in the surface defects formed rather than anatase to rutile phase transformation as reported by others. Controlled darkening of TiO₂ film might be used for adjustable filters.     

Femtosecond pulsed laser deposition of nanostructured TiO2 films

Nanostructured deposits of TiO₂ were grown on Si (1 0 0) substrates by laser ablating a TiO₂ sintered target in vacuum or in oxygen using a Ti:sapphire laser delivering 80 fs pulses. The effect of the laser irradiation wavelength on the obtained nanostructures, was investigated using 800, 400 and 266 nm at different substrate temperatures and pressures of oxygen. The composition of the deposits was characterized using X-ray photoelectron spectroscopy (XPS) and the surface morphology was studied by environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). Deposits are absent of microscopic droplets in all conditions explored. The best deposits, constituted by nanoparticles of an average diameter of 30 nm with a narrow size distribution, were obtained at the shorter laser wavelength of 266 nm under vacuum at substrate room temperature.     

Application of the laser ablation for conservation of historical paper documents

Laser ablation was applied for surface cleaning and spectroscopic diagnostics of historical paper documents and model samples in the framework of the conservation projects. During cleaning the spectra of ablation products were recorded by means of the LIBS technique which allowed for nearly non-destructive identification of surface layers such as contaminants, substrate and pigments. For consecutive laser pulses a strong decrease of band intensities of the emission lines of Ca, Na, K, Al and Fe ascribed to contaminants were observed. The effect was used for monitoring of the cleaning progress of stained paper. For surface cleaning and spectra excitation the Q-switched Nd:YAG laser of 6 ns pulsewidth operating at wavelengths of 266, 355, 532, and 1064 nm and of fluence selected from the range 0.3-0.9 J/cm² was applied. The ablation parameters were optimized in agreement with the literature and the results were confirmed by surface studies and testing of the mechanical and chemical properties, and also by the response to the ageing process of the paper substrate. In case of the model paper irradiated in the UV range at 266 and 355 nm a visual inspection revealed local damages of the cellulose fibers accompanied by a decrease of the mechanical strength of the substrate. The effect was more pronounced after artificial ageing. The best results were obtained for samples irradiated at 532 nm and at laser fluence below the damage threshold of 0.6 J/cm², which is in agreement with literature.     

A study on UV laser drilling of PEEK reinforced with carbon fibers

This paper deals with the application of Nd-YAG laser emitting at 355 nm to the drilling process of Carbon Fiber Reinforced Polyetheretherkethone (PEEK-CF) laminates. The combination of a modern UV-laser source with a scanning technology enabling speeds up to 4 m/s, suppresses heat affected zones (HAZ) and consequently detachment of fibers from the polymer matrix. A removal technique based on the ablation of superimposed layers of composite material is proposed and analyzed in detail as a function of energy density delivered to the surface, hatch strategy and thickness of the laminate to be drilled. The hatching technique discussed in the paper is compared with conventional laser trepanning and percussion drilling through holes for the realization of 2 mm and 0.1 mm diameter, respectively. In both the cases benefits were noticed in terms of extension of HAZ and quality of the cut edges.     

Laser fluence, repetition rate and pulse duration effects on paint ablation

The efficiency (mm³/(J pulse)) of laser ablation of paint was investigated with nanosecond pulsed Nd:YAG lasers (λ = 532 nm) as a function of the following laser beam parameters: pulse repetition rate (1-10,000 Hz), laser fluence (0.1-5 J/cm²) and pulse duration (5 ns and 100 ns). In our study, the best ablation efficiency (η ≅ 0.3 mm³/J) was obtained with the highest repetition rate (10 kHz) at the fluence F = 1.5 J/cm². This ablation efficiency can be associated with heat accumulation at high repetition rate, which leads to the ablation threshold decrease. Despite the low thermal diffusivity and the low optical absorption of the paint (thermal confinement regime), the ablation threshold fluence was found to depend on the pulse duration. At high laser fluence, the ablation efficiency was lower for 5 ns pulse duration than for the one of 100 ns. This difference in efficiency is probably due to a high absorption of the laser beam by the ejected matter or the plasma at high laser intensity. Accumulation of particles at high repetition rate laser ablation and surface shielding was studied by high speed imaging.     

XPS studies of short pulse laser interaction with copper

The effect of laser ablation on copper foil irradiated by a short 30 ns laser pulse was investigated by X-ray photoelectron spectroscopy. The laser fluence was varied from 8 to 16.5 J/cm² and the velocity of the laser beam from 10 to 100 mm/s. This range of laser fluence is characterized by a different intensity of laser ablation. The experiments were done in two kinds of ambient atmosphere: air and argon jet gas.The chemical state and composition of the irradiated copper surface were determined using the modified Auger parameter (α′) and O/Cu intensity ratio. The ablation atmosphere was found to influence the size and chemical state of the copper particles deposited from the vapor plume. During irradiation in air atmosphere the copper nanoparticles react with oxygen and water vapor from the air and are deposited in the form of a CuO and Cu(OH)₂ thin film. In argon atmosphere the processed copper surface is oxidized after exposure to air.     

Femtosecond and nanosecond laser damage thresholds of doped and undoped triazenepolymer thin films

The influence of pulse duration on the laser-induced damage in undoped or infrared-absorbing-dye doped thin triazenepolymer films on glass substrates has been investigated for single, near-infrared (800 nm) Ti:sapphire laser pulses with durations ranging from 130 fs up to 540 fs and complementarily for infrared (1064 nm) Nd:YAG ns-laser single-pulse irradiation. The triazenepolymer material has been developed for high resolution ablation with irradiation at 308 nm. Post-irradiation optical microscopy observations have been used to determine quantitatively the threshold fluence for permanent laser damage. In contrast to our previous studies on a triazenepolymer with different composition [J. Bonse, S.M. Wiggins, J. Solis, T. Lippert, Appl. Surf. Sci. 247 (2005) 440], a significant dependence of the damage threshold on the pulse duration is found in the sub-picosecond regime with values ranging from ∼500 mJ/cm² (130 fs) up to ∼1500 mJ/cm² (540 fs). Other parameters such as the film thickness (50 nm and 1.1 μm samples) or the doping level show no significant influence on the material behavior upon irradiation. The results for fs- and ns-laser pulse irradiation are compared and analyzed in terms of existent ablation models.     

Generation of nanospikes via laser ablation of metals in liquid environment and their activity in surface-enhanced Raman scattering of organic molecules

The formation of dense arrays of nanospikes occurs under laser ablation of bulk targets (Ag, Au, Ta, Ti) immersed in liquids such as water or ethanol. The average height of spikes is 50 nm and their density on the target amounts to 10¹⁰ cm⁻². The effect is observed with sufficiently short laser pulses. In particular, either a 350 ps or a 90 ps Nd:YAG lasers are used in their fundamental harmonics. The nanospikes are characterized by UV-Visible reflection spectrometry and atomic force microscopy. The oscillations of electrons within nanospikes result in a permanent coloration of the surface and a modification of the optical reflection spectra of the metal. Scanning the laser beam along the metal surface allows its nanostructuring over extended areas (∼1 cm²). The nanostructured Ag surface shows enhanced Raman scattering of acridine molecules at a concentration of 10⁻⁵ M/l, whereas the initial Ag targets do not show any signal within the accuracy of measurements.     

Effect of spot size on cone formation in a XeCl laser ablation of polyethersulfone films

Radiation from the UV excimer lasers, with the fluence above the ablation threshold, can etch the polymer surfaces by photoablation. In some cases different microstructures may appear on the surface during the laser ablation. In this paper the effect of the laser spot size on the cone formation on polyethersulfone films has been investigated. The experiments have been performed with a XeCl laser at the wavelength of 308 nm and at the fluences of 70 and 100 mJ/cm² at air. For the investigation of the effect of the laser spot size on cone formation, the samples were irradiated at two different laser spot sizes of w₁ and w₂ = 0.1 w₁. The morphology of the processed surface was studied by scanning electron microscopy (SEM). It has shown that the shape, size and density of cones change with the change of the laser spot size. Also, the number of pulses and the pulse repetition rate which are needed for threshold of cone formation are affected by the laser beam spot size on the surface.     

Synthesis and characterization of Co (Ni or Cu)-MCM-41 mesoporous molecular sieves with different amount of metal obtained by using microwave irradiation method

Co (Ni or Cu)-MCM-41 mesoporous molecular sieves with different amount of metal were synthesized by using cetyltrimethyl ammonium bromide as a template and by a novel microwave irradiation method. These samples were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and N₂ physical adsorption. The experimental results show that Co (Ni or Cu)-MCM-41 mesoporous molecular sieves were successfully synthesized. When the as-synthesized samples were calcined at 550 °C for 10 h, the template was effectively removed. Under microwave irradiation condition, Co-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 745.7-1188.8 m²/g and average pore sizes in a range of 2.46-2.75 nm; Ni-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 625.8-1161.3 m²/g and average pore sizes of ca. 2.7 nm; Cu-MCM-41 mesoporous molecular sieves have specific surface areas in a range of 601.6-1142.9 m²/g and average pore sizes in a range of 2.46-2.76 nm. On the other hand, with increasing the introduced metal amount, the specific surface area and pore volume of the synthesized Co (Ni or Cu)-MCM-41 mesoporous molecular sieves became small, and the mesoporous ordering of the samples became poor. Under the comparable synthesis conditions, the synthesized Co-MCM-41 mesoporous molecular sieve has a bigger specific surface area and a more uniform pore distribution as compared with the synthesized Ni-MCM-41and Cu-MCM-41 mesoporous molecular sieves.     

Patterning of indium-tin oxide on glass with picosecond lasers

The results of patterning of the indium-tin oxide (ITO) film on the glass substrate with high repetition rate picosecond lasers at various wavelengths are presented. Laser radiation initiated the ablation of the material, forming grooves in ITO. Profile of the grooves was analyzed with a phase contrast optical microscope, a stylus type profiler, scanning electron microscope (SEM) and atomic force microscope (AFM). Clean removal of the ITO film was achieved with the 266 nm radiation when laser fluence was above the threshold at 0.20 J/cm², while for the 355 nm radiation, the threshold was higher, above 0.46 J/cm². The glass substrate was damaged in the area where the fluence was higher than 1.55 J/cm². The 532 nm radiation allowed getting well defined grooves, but a lot of residues in the form of dust were generated on the surface. UV radiation with the 266 nm wavelength provided the widest working window for ITO ablation without damage of the substrate. Use of UV laser radiation with fluences close to the ablation threshold made it possible to minimize surface contamination and the recast ridge formation during the process.     

Preparation and ablation properties of ZrC-SiC coating for carbon/carbon composites by solid phase infiltration

A novel ZrC-SiC coating was prepared on carbon/carbon (C/C) composites surface by solid phase infiltration and the ablation properties of the ZrC-SiC coated C/C composites under oxyacetylene flame were studied. The results show that the coating prepared on the condition of optimum process parameters exhibits dense surface and outstanding anti-ablation ability. After ablation for 20 s, the mass ablation rates of the coated C/C composites can be lowered to 2.36 × 10⁻³ g/s, 37.1% reduction compared with uncoated C/C composites. The oxide layer composed of ZrO₂ and SiO₂ acts as oxygen diffusion barrier and the evaporation of ZrO₂ and SiO₂ absorbs a great amount of heat from the flame and reduces the erosive attack on the coating.     

Low temperature synthesis of iodine-doped TiO2 nanocrystallites with enhanced visible-induced photocatalytic activity

Iodine-doped TiO₂ nanocrystallites (denoted as I-TNCs) were prepared via a newly developed triblock copolymer-mediated sol-gel method at a temperature of 393 K. I-doping, crystallization and the formation of porous structure have been simultaneously achieved. The obtained particles were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and UV-vis spectrophotometer. The results indicated that the as-prepared I-TNCs possessed a diameter of ca. 5 nm with anatase crystalline structure and a specific surface area of over 200 m² g⁻¹. The presence of iodine expanded the photoresponse in visible light range, and led to enrich in surface hydroxyl group on the TiO₂ surface. Compared with the commercial photocatalyst P25, the I-TNCs significantly enhanced the photocatalytic efficiency in the degradation of rhodamine B and 2,4-dichlorophenol, and the I-TNCs with 2.5 mol% doping ratio exhibited the best photocatalytic activity.     

Local chemical transformations in poly(dimethylsiloxane) by irradiation with 248 and 266 nm

Poly(dimethylsiloxane) (PDMS) has been irradiated with a frequency quadrupled Nd:YAG laser and a KrF^*-excimer laser at a repetition rate of 1 Hz. The analysis of ablation depth versus pulse number data reveals a pronounced incubation behavior. The thresholds of ablation (266 nm: 210 mJ cm⁻², 248 nm: 940 mJ cm⁻²) and the corresponding effective absorption coefficients α_eff (266 nm: 48900 cm⁻¹, 248 nm: 32700 cm⁻¹, α_lin = 2 cm⁻¹) were determined. The significant differences in the ablation thresholds for both irradiation wavelengths are probably due to the different pulse lengths of both lasers. Since the shorter pulse length yields a lower ablation threshold, the observed incubation can be due to a thermally induced and/or a multi-photon absorption processes of the material or impurities in the polymer.Incubation of polymers is normally related to changes of the chemical structure of the polymer. In the case of PDMS, incubation is associated with local chemical transformations up to several hundred micrometers below the polymer surface. It is possible to study these local chemical transformations by confocal Raman microscopy, because PDMS is transparent in the visible. The domains of transformation consist of carbon and silicon, as indicated by the appearance of the carbon D- and G-bands between 1310 and 1610 cm⁻¹, a band appearing between 502 and 520 cm⁻¹ can be assigned to mono- and/or polycrystalline silicon.The ablation products, which are detected in the surroundings of the ablation crater consist of carbon and amorphous SiO_x (x ≈ 1.5) as detected by infrared spectroscopy.     

A green synthetic approach to graphene nanosheets for hydrogen adsorption

A green and facile strategy of preparing graphene by reducing exfoliated graphite oxide (GO) with glucose was developed in this study. The as-prepared samples were characterized by X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The characterization results indicated that the graphene sheets (GS) were of high quality with smooth surface, rich pore structure and few layer graphene. The samples have a BET specific surface area of 1205.8 m² g⁻¹ measured by N₂ adsorption at 77 K. The hydrogen storage capacity of 2.7 wt.% at 298 K and 25 bar demonstrated that the as-prepared graphene employing glucose as reductant is supposed to be a promising material with outstanding property for hydrogen storage.     

Bioactive glass and hydroxyapatite thin films obtained by pulsed laser deposition

Bioactive glass (BG), calcium hydroxyapatite (HA), and ZrO₂ doped HA thin films were grown by pulsed laser deposition on Ti substrates. An UV KrF^* (λ = 248 nm, τ ≥ 7 ns) excimer laser was used for the multi-pulse irradiation of the targets. The substrates were kept at room temperature or heated during the film deposition at values within the (400-550 °C) range. The depositions were performed in oxygen and water vapor atmospheres, at pressure values in the range (5-40 Pa). The HA coatings were heat post-treated for 6 h in a flux of hot water vapors at the same temperature as applied during deposition. The surface morphology, chemical composition, and crystalline quality of the obtained thin films were studied by scanning electron microscopy, atomic force microscopy, and X-ray diffractometry. The films were seeded for in vitro tests with Hek293 (human embryonic kidney) cells that revealed a good adherence on the deposited layers. Biocompatibility tests showed that cell growth was better on HA than on BG thin films.     

Evolution of InP surfaces under low fluence pulsed UV irradiation

An InP wafer was irradiated in air by a series of UV pulses from a nitrogen laser with fluences of 120 mJ/cm² and 80 mJ/cm². These fluences are below the single-pulse ablation threshold of InP. Over the studied region the distribution of the radiation intensity was uniform. The number of pulses varied from 50 to 6000. The evolution of the surface morphology and structure was characterized by atomic force microscopy, optical microscopy and Raman spectroscopy. The relationship between mound size and the number of pulses starts out following a power law, but saturates for a sufficiently high number of pulses. The crossover point is a function of fluence. A similar relation exists for the surface roughness. Raman spectroscopic investigations showed little change in local crystalline structure of the processed surface layer.