不同退火温度下氧化锌薄膜可见发光与n型导电研究

采用脉冲激光沉积法在蓝宝石衬底上制备出可见光发光良好的氧化锌薄膜, 在不同的温度下进行了后退火处理. 随着退火温度的升高, 薄膜的可见光发光发生了显著改变, 载流子浓度、迁移率、电阻率也呈现出一定的变化规律. 结合 X射线衍射、扫描电子显微镜、光致发光谱及霍尔测量, 探讨了本征氧化锌薄膜可见光发光的发射机理, 并分析了其 n型导电的原因. 关键词： 氧化锌薄膜 可见光发光 n型导电     

Relationship between the photoluminescence and conductivity of undoped ZnO thin films grown with various oxygen pressures

The pulsed laser deposition (PLD) technique is used to deposit undoped ZnO thin films on glass substrates at 150 °C with different oxygen pressures of 40, 80, 100 and 150 mTorr. X-ray diffraction (XRD) and atomic force microscopy (AFM) studies indicated that the obtained ZnO thin films were hexagonal wurtzite-type structures with strong (0 0 2) c-axis orientation. The relationship between photoluminescence and the conductivity of the ZnO thin films grown by pulsed laser deposition at various oxygen pressures was also discussed. The intensity of the deep-level-emission (DLE) and conductivity generally increased as the oxygen pressure decreased. The intensity of DLE peak was generally proportional to the conductivity. The band gap energy values, determined from transmittance spectra, were around 3.30-3.34 eV, and decreased when the oxygen pressure increased.     

纳米ZnO和ZnO-SiO2复合薄膜的光学性质研究

通过溶胶凝胶(sol-gel)法分别在玻璃衬底上制备了ZnO纳米薄膜和ZnO-SiO₂纳米复合薄膜,并利用紫外-可见光分光光度计对薄膜的光学性能进行了分析.可见光-紫外透射谱显示,随着ZnO溶胶浓度从0.7mol/L降低到0.006mol/L,制备的ZnO薄膜从只出现一个380nm(对应的光学禁带宽度为3.27eV)左右的吸收边到在380和320nm(对应的光学禁带宽度为3.76eV)左右各出现一个吸收边,并且随着ZnO溶胶浓度的降低,在380—320nm波段内的透过率明显提高.而Z 关键词： 纳米ZnO 2复合薄膜')" href="#">ZnO-SiO₂复合薄膜 溶胶凝胶法 透射率     

p-type ZnO films for preparation of p-n-junctions

Photoelectrical properties of ZnO films doped with Li acceptor impurity and prepared by the electron-beam evaporation method were investigated. The obtained films possess a p-type conductivity. Using p-ZnO:Li and n-ZnO:Ga films, the p-n-junctions were prepared and their photoelectrical properties were studied. The mechanism of charge carrier transport in these films and the influence of annealing on the type and mechanism of conductivity were investigated.     

Optical and electrical properties of p-type ZnO fabricated by NH3 plasma post-treated ZnO thin films

In this paper, a simple method is reported to obtain nitrogen-doped p-ZnO film. In this method NH₃ plasma, generated in a plasma-enhanced chemical vapor deposition system, was employed to treat ZnO thin film. By Hall-effect measurement, a p-type conductivity was observed for the treated film with the hole density of 2.2 × 10¹⁶ cm⁻³. X-ray photoelectron spectroscopy (XPS) results confirmed that nitrogen was incorporated into ZnO film during the treatment process to occupy the oxygen positions. In low temperature photoluminescence spectra, an emission peak corresponding to acceptor-donor pair was observed. From this emission peak we calculated the N-related acceptor binding energy to be 130 meV.     

Structural and optical properties of ZnO thin films on (111) CaF2 substrates grown by magnetron sputtering

ZnO thin films were grown on (111) CaF₂ substrates by magnetron sputtering at room temperature. Structural and optical properties of the ZnO thin films were studied. XRD analysis showed that the ZnO thin films had the (002) preferential orientation. The transmittance of ZnO thin films was over 80% in the visible range. The optical band gap of the ZnO thin films was 3.26 eV. The optical constants (n,k)$(n,k)$ of the ZnO thin films in the wavelength range 300–1000 nm were obtained by infrared spectroscopic ellipsometry measurement. PL spectra of ZnO thin films showed strong UV near-band-edge emission peak at 376.5 nm and weak visible red emission at 643.49 nm using He–Cd laser as the light source, using a synchrotron radiation light source PL spectra showed three emission peak at 320 nm, 410 nm and 542 nm respectively.     

Characterization of ZnO thin films grown on various substrates by RF magnetron sputtering

In this study we investigated properties of ZnO thin films deposited on both oxygen-containing substrates and a substrate without oxygen content at various O₂/Ar reactant gas ratios. Deposition of ZnO on indium-tin oxide (ITO) resulted in the best crystallinity, whereas the least degree of crystallization was observed from ZnO deposited on glass. All the films were found to have compressive stress, which was relieved by annealing in O₂ environment. ZnO films deposited on glass revealed p-type conductivity when prepared at O₂/Ar ratio of 0.25 whereas those on SiN_x yielded p-type conductivity when prepared at O₂/Ar ratio of 4. In addition, shallower oxygen interstitial seemed to be found from films with better crystallinity. The largest shift in binding energy of Zn_2p3/2 was observed from ZnO prepared on glass at O₂/Ar ratio of 0.25, whereas that of O_1s was obtained from ZnO deposited on SiN_x at O₂/Ar ratio of 4. A model was proposed in terms of O₂ diffusion and hydrogen desorption in order to account for the observed property variations depending on substrates and O₂/Ar ratios.     

原位氧化Zn3N2制备p型ZnO薄膜的性能研究

采用射频反应溅射法在玻璃衬底上制备Zn₃N₂薄膜，然后向真空室中通入纯氧气进行热氧化制备ZnO薄膜.利用X射线衍射、扫描电子显微镜、霍尔效应测量、透射光谱和光致发光光谱等表征技术，研究了氧化温度和氧化时间对ZnO薄膜的结晶质量、电学性质和光学性能的影响.研究结果显示，450 ℃ 下氧化2 h后的样品中除含有ZnO外，还有Zn₃N₂成分，500 ℃下氧化2 h可以制备出电阻率为0.7 Ωcm，空穴载流子浓度为10^{关键词： p型ZnO薄膜 3N₂薄膜')" href="#">Zn₃N₂薄膜 射频溅射 原位氧化}     

Influence of high-pressure hydrogen treatment on structural and electrical properties of ZnO thin films

ZnO thin films were treated by high-pressure hydrogen (H₂). Scanning electron microscope (SEM) images show that the surface morphology of ZnO films has been changed significantly by H₂ treatment. X-ray diffraction patterns show that the Zn(OH)₂ phases formed after H₂ treatment. The X-ray photoelectron spectroscopy results indicate that H atoms were doped into the surface of ZnO by forming H-O-Zn bond. The phenomenon shows that it is easy to form O-H bond in ZnO rather than H interstitial atom under high-pressure hydrogen circumstance.     

The effects of thermal annealing in NH3 -ambient on the p-type ZnO films

Thermal annealing in NH₃-ambient was carried out to form p-type ZnO films. The properties were examined by X-ray diffraction (XRD), Hall-effect measurement, photoluminescence (PL), and secondary ion mass spectrometry (SIMS). Electron concentrations in ZnO films were in the range of 10¹⁵–10¹⁷/cm³ with thermal annealing in NH₃-ambient. The activation thermal annealing process was needed at 800 C under N₂-ambient to obtain p-type ZnO. The electrical properties of the p-type ZnO showed a hole concentration of 1.06×10¹⁶/cm³, a mobility of 15.8 cm²/V s, and a resistivity of 40.18 Ω cm. The N-doped ZnO films showed a strong photoluminescence peak at 3.306 eV at 13 K, which is closely related to neutral acceptor bound excitons of the p-type ZnO. The incorporation of nitrogen was confirmed in the SIMS spectra.     

Temperature dependence of the optical band gap and electrical conductivity of sol-gel derived undoped and Li-doped ZnO films

Undoped and lithium (Li)-doped ZnO films were prepared by sol-gel method using spin coating technique. The effects of Li content on the crystallinity and morphological properties of ZnO films were assessed by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). XRD patterns of the films showed the hexagonal wurtzite type polycrystalline structure and that the incorporation of lithium leads to substantial changes in the structural characteristics of ZnO films. The SEM and AFM measurements showed that the surface morphology of the films was affected from the lithium incorporation. The wrinkle network was observed on the surface from both SEM and AFM results for undoped ZnO. The wrinkle structure disappeared with increasing Li content. The absorption spectra of the ZnO and 5% Li-doped ZnO (LZO5) films were carried out between 140 and 400 K temperatures. The optical band gap of ZnO and LZO5 films (calculated at various temperatures) showed a linear dependence on the temperature. The absolute zero value optical band gap and the rate of change of the band gap with temperature of the ZnO and LZO5 films were found to be 3.339 and 3.322 eV, and 2.95 × 10⁻⁴ and 1.60 × 10⁻⁴ eV/K, respectively. The transport mechanisms in the ZnO and LZO5 films have been investigated by analyzing of the temperature (80-300 K) dependence of the conductivity. The activation energies of the ZnO film increased with Li content.     

Thermal conductivity of thermoelectric Al‐substituted ZnO thin films

ZnO:Al thin films with a low electrical resistivity were grown by magnetron sputtering on sapphire substrates. The cross‐plane thermal conductivity (κ = 4.5 ± 1.3 W/mK) at room temperature is almost one order of magnitude lower than for bulk materials. The thermoelectric figure of merit ZT at elevated temperatures was estimated from in‐plane power factor and the cross‐plane thermal conductivity at room temperature. It is expected that the thermal conductivity drops with increasing temperature and is lower in‐plane than cross‐plane. Consequently, the thin film ZT is at least three times higher than for bulk samples at intermediate temperatures. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Defects related room temperature ferromagnetism in p-type (Mn, Li) co-doped ZnO films deposited by reactive magnetron sputtering

We report on the defects related room temperature ferromagnetic characteristics of Zn_0.95-xMn_xLi_0.05O (x = 0.01, 0.03, 0.05 and 0.08) thin films grown on glass substrates using reactive magnetron sputtering. By increasing the Mn content, the films exhibited increases in the c-axis lattice constant, fundamental band gap energy, coercive field and remanent magnetization. Comparison of the structural and magnetic properties of the as-deposited and annealed films indicates that the hole carriers, together with defects concentrations, play an important role in the ferromagnetic origin of Mn and Li co-doped ZnO thin films. The ferromagnetism in films can be described by bound magnetic polaron models with respect to defect-bound carriers.     

Effect of annealing temperature on photocatalytic activity of ZnO thin films prepared by sol-gel method

Zinc oxide thin films are deposited on Si and quartz substrates using the sol-gel method. The thin films, annealed at 400, 600 and 800 °C respectively, are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), ultraviolet-visible spectrophotometer (UV-Vis), fluorescence spectrometer (FL) and the photocatalytic activity is tested by the decomposition of methyl orange dye under UV illumination. The results show that the mean grain size, surface-to-volume ratio, rms roughness and degradation efficiency of the thin films increases with increasing annealing temperature. In particular, ZnO thin film annealed at 800 °C exhibits the highest photocatalytic activity, degrading methyl orange by almost 88% in 180 min. Photocatalytic reaction mechanism of the ZnO thin films is discussed in detail, and the oxygen defects are proposed to be the active sites of the ZnO photocatalyst.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Structural characterization of supported nanocrystalline ZnO thin films prepared by dip-coating

Nanocrystalline ZnO thin films prepared by the sol-gel dip-coating technique were characterized by grazing incidence X-ray diffraction (GIXD), atomic force microscopy (AFM), X-ray reflectivity (XR) and grazing incidence small-angle X-ray scattering (GISAXS). The structures of several thin films subjected to (i) isochronous annealing at 350, 450 and 550 °C, and (ii) isothermal annealing at 450 °C during different time periods, were characterized. The studied thin films are composed of ZnO nanocrystals as revealed by analysing several GIXD patterns, from which their average sizes were determined. Thin film thickness and roughness were determined from quantitative analyses of AFM images and XR patterns. The analysis of XR patterns also yielded the average density of the studied films. Our GISAXS study indicates that the studied ZnO thin films contain nanopores with an ellipsoidal shape, and flattened along the direction normal to the substrate surface. The thin film annealed at the highest temperature, T = 550 °C, exhibits higher density and lower thickness and nanoporosity volume fraction, than those annealed at 350 and 450 °C. These results indicate that thermal annealing at the highest temperature (550 °C) induces a noticeable compaction effect on the structure of the studied thin films.     

Influence of annealing temperature on the photoluminescence property of ZnO thin film covered by TiO2 nanoparticles

In this work, ZnO thin films covered by TiO₂ nanoparticles (labeled as TiO₂-ZnO thin films) were prepared by electron beam evaporation. The influence of annealing temperature on the photoluminescence property of the samples was studied. The structures and surface morphologies of the samples were analyzed by X-ray diffraction (XRD) and atomic force microscope, respectively. The photoluminescence was used to investigate the fluorescent properties of the samples. The measurement results show that the ultraviolet emission of ZnO thin films is largely enhanced after they are covered by TiO₂ nanoparticles, while the green emission is suppressed. However, when the annealing temperature is relatively high (≥500 °C), the intensity of ultraviolet emission drops off and a violet emission peak along with a blue emission peak appears. This is probably connected with the atomic interdiffusion between TiO₂ nanoparticles and ZnO thin film. Therefore, selecting a suitable annealing temperature is a key factor for obtaining the most efficient ultraviolet emission from TiO₂-ZnO thin films.     

Influence of growth temperature of TiO2 buffer on structure and PL properties of ZnO films

A series of ZnO films with TiO₂ buffer on Si (1 0 0) substrates were prepared by DC reactive sputtering. Growth temperature of TiO₂ buffer changed from 100 °C to 400 °C, and the influence on the crystal structures and optical properties of ZnO films have been investigated. The XRD results show that the ZnO films with TiO₂ buffer have a hexagonal wurtzite structure with random orientation, and with the increase of growth temperature of TiO₂ buffer, the residual stresses were released gradually. Specially, the UV emission enhanced distinctly and FWHMs (full width half maximum) decreased linearly with the increasing TiO₂ growth temperature. The results all come from the improvement of crystal quality of ZnO films.     

Optical properties of p-type CuAlO2 thin film grown by rf magnetron sputtering

We report the structural and optical properties of copper aluminium oxide (CuAlO₂) thin films, which were prepared on c-plane sapphire substrates by the radio frequency magnetron sputtering method. X-ray photoelectron spectroscopy (XPS) along with X-ray diffraction (XRD) analysis confirms that the films consist of delafossite CuAlO₂ phase only. The optical absorption studies show the indirect and direct bandgap is 1.8 eV and 3.45 eV, respectively. Room temperature photoluminescence (PL) measurements show three emission peaks at 360 nm (3.45 eV), 470 nm (2.63 eV) and 590 nm (2.1 eV). The first one is near band edge emission while the other two are originated from defects.