Optical and hydrophilic properties of Cr doped TiO2-SiO2 nanostructure thin film

Cr doped TiO₂-SiO₂ nanostructure thin film on glass substrates was prepared by a sol-gel dip coating process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the structural and chemical properties of the films. A UV-vis spectrophotometer was used to measure the transmittance spectra of the thin film. The hydrophilicity of the thin film during irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that Cr doping has a significant effect on the transmittance and super-hydrophilicity of TiO₂-SiO₂ thin film.     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Preparation and photoelectrochemical performance of Ag/graphene/TiO2 composite film

By dipping-lifting in sol-gel solution and reducing process, the graphene/TiO₂ composite film on the glass plate was first prepared. Then, the Ag/graphene/TiO₂ composite film was fabricated by interface reaction with AgNO₃ and N₂H₄·H₂O on the surface of graphene/TiO₂ composite film. The characterization results show that the uniform porous TiO₂ film is made up of the anatase crystal, and the Ag/graphene/TiO₂ composite film is constructed by doping or depositing graphene sheets and Ag nanoparticles on the surface of TiO₂ film. The photoelectrochemical measurement results indicate that the Ag/graphene/TiO₂ composite film has an excellent photoelectrochemical conversion property.     

Preparation and characterization of PES/TiO2 composite membranes

Polyethersulfone (PES)/TiO₂ composite membranes were prepared by phase inversion method with nano-TiO₂ as additive. The influence of TiO₂ on the morphologies and the performances of PES/TiO₂ membranes were investigated through the methods of SEM, XRD, TGA, contact angle goniometer, mechanical strength tests and filtration experiments. The results showed that the structure of membrane was not obviously affected by addition of TiO₂, and the performances such as hydrophilicity, thermal stability, mechanical strength and anti-fouling ability of membrane were enhanced through adding TiO₂ nanoparticles. At 0.5 wt.% TiO₂ content, the composite membrane has an excellent performance, however higher TiO₂ content (than 0.5 wt.%) resulted in defective pore structure of the membranes and decline of the performances, such as permeability and mechanical strength. TGA and mechanical strength analyses indicated good compatibility between polymers and TiO₂ nanoparticles.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

Influence of the OH groups on the photocatalytic activity and photoinduced hydrophilicity of microwave assisted sol-gel TiO2 film

In the present work the influence of the OH groups on the photocatalytic activity and the photoinduced hydrophilicity of microwave assisted sol-gel TiO₂ films was investigated. The prepared TiO₂ films were characterized using XRD and AFM. Furthermore, the surface of the TiO₂ films was examined by help of XPS in order to determine the amount of OH groups before and after UV irradiation at different humidities. The activity of the TiO₂ films was determined using stearic acid as a model compound and the photoinduced superhydrophilicity was investigated through contact angle measurements.The results of this investigation showed that the microwave assisted sol-gel technique produces highly homogeneous and efficient TiO₂ films without the need for heat treatment for crystallization. Based on the conducted experiments it is suggested that the amount of OH groups on the TiO₂ surface highly influence the photocatalytic activity and the photoinduced superhydrophilicity and that the two mechanisms may be closely related. It is suggested that the superhydrophilicity is obtained through a combination of photocatalytic degradation of organic contaminants and surface structural changes in form of an increased amount of OH-groups.     

Catalytic growth of TiO2 nanowires from a TiN thin film

We report in this work synthesis of TiO₂ nanowires from a TiN thin film overlayed with nickel. The nanowires have been analyzed with EELS, XPS, XRD and HRTEM. It has been shown that the nanowires are single-crystalline and of the rutile structure. The growth mechanism has been studied, allowing to determine in which process conditions synthesis of nanowires occurs and to propose a growth scenario.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Study of Al2O3/TiO2 reflectivity enhancing bi-layer films on bright aluminium substrates

Al₂O₃/TiO₂ bi-layer films on aluminium substrates have been obtained by combining anodising and TiO₂ sol-gel deposition. The reflectivity enhancing properties of these Al₂O₃/TiO₂ bi-layer films have been studied in relation to the refractive index and thickness of the Al₂O₃ and TiO₂ single-layers. It is shown that a significant improvement of reflectivity can be achieved by a proper optimisation of the bi-layer elaboration parameters.     

Cocktail effect of Fe2O3 and TiO2 semiconductors for a high performance dye-sensitized solar cell

The bi-semiconductors of TiO₂ and Fe₂O₃ were used as a photoelectrode material in a high performance dye-sensitized solar cell due to cocktail effects from the two conduction bands. The size of the semiconductors was reduced by using a paint shaker to enlarge the contact area of the semiconductor with the dye or electrolyte. The fill factor and the efficiency of the prepared dye-sensitized solar cell were improved by over 16% and 300%, respectively; these parameters were measured from a current-voltage curve that was based on the effects of the Fe₂O₃ co-semiconductor and the size reduction. A mechanism is suggested wherein the conduction band of Fe₂O₃ works to prohibit the trapping effects of electrons in the conduction band of TiO₂. This result is attributed to the prevention of electron recombination between electrons in the TiO₂ conduction band with dye or electrolytes. The mechanism is suggested based on impedance results, which indicate improved electron transport at the interface of the TiO₂/dye/electrolyte.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Room temperature ferromagnetism in vacuum-annealed TiO2 thin films

Thin films of pure TiO₂ have been prepared using both spin-coating and sputter-deposition techniques on sapphire and quartz substrates. The structural characteristics of the films have been investigated in detail using Raman spectroscopy and high-resolution transmission electron microscopy (HRTEM). When annealed in vacuum, all films demonstrate room temperature ferromagnetism, while the air-annealed samples show much smaller, often negligible, magnetic moments. The magnetization of the vacuum-annealed sputtered samples depends on film thickness, with the volume magnetization decreasing monotonically with increasing thickness. Furthermore, the magnetization per unit area also decreases slightly with increasing film thickness. These results suggest that ferromagnetism in the vacuum-annealed TiO₂ films is mediated by surface defects or interfacial effects, but does not arise from stoichiometric crystalline TiO₂.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

Fabrication, characterization and photoelectrochemical properties of Fe2O3 modified TiO2 nanotube arrays

TiO₂ nanotube (NT) arrays modified by Fe₂O₃ with high sensibility in the visible spectrum were first prepared by annealing anodic titania NTs pre-loaded with Fe(OH)₃ which was uniformly clung to the titania NTs using sequential chemical bath deposition (S-CBD). The photoelectrochemical performances of the as-prepared composite nanotubes were determined by measuring the photo-generated currents and voltages under illumination of UV-vis light. The titania NTs modified by Fe₂O₃ showed higher photopotential and photocurrent values than those of unmodified titania NTs. The enhanced photoelectrochemical behaviors can be attributed to the modified Fe₂O₃ which increases the probability of charge-carrier separation and extends the range of the TiO₂ photoresponse from ultraviolet (UV) to visible region due to the low band gap of 2.2 eV of Fe₂O₃.     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

Electrodeposition and properties of Zn-nanosized TiO2 composite coatings

Nanosized TiO₂ particles were prepared by sol-gel method. The TiO₂ particles were co-deposited with zinc from a sulphate bath at pH 4.5 using electrodeposition technique. The corrosion behavior of the coatings was assessed by electrochemical polarization, impedance, weight-loss and salt spray tests. Wear resistance and microhardness of the composite coating was measured. The smaller grain size of the composite coatings was observed in the presence of TiO₂ and it was confirmed by the images of scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques.     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

Enhanced photoelectrochemical properties of F-containing TiO2 sphere thin film induced by its novel hierarchical structure

The novel nanostructured F-containing TiO₂ (F-TiO₂) sphere was directly synthesized on the surface of Ti foil in the solution of NH₄F and HCl by one-step hydrothermal approach under low-temperature condition. The samples were characterized respectively by means of field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The results showed that the F-TiO₂ sphere was hierarchical structure, which composed of porous octahedron crystals with one truncated cone, leading to a football-like morphology. XPS results indicated that F⁻ anions were just physically adsorbed on the surface of TiO₂ microspheres. The studies on the optical properties of the F-TiO₂ were carried out by UV-vis light absorption spectrum. The surface fluorination of the spheres, the unique nanostructure induced accessible macropores or mesopores, and the increased light-harvesting abilities were crucial for the high photoelectrochemical activity of the synthesized F-TiO₂ sphere for water-splitting. The photocurrent density of the F-TiO₂ sphere thin film was more than two times than that of the P25 thin film. Meanwhile, a formation mechanism was briefly proposed. This approach could provide a facile method to synthesize F-TiO₂ microsphere with a special morphology and hierarchical structure in large scale.