Correlation between bioactivity and structural properties of titanium dioxide coatings grown by atomic layer deposition

TiO₂ coatings were grown on Ti and Si by Atomic Layer Deposition (ALD) from titanium ethoxide and water at 300 °C in a wide range of the reaction cycles number N = 100-2000. TiO₂ coatings were found to be amorphous at low value of N < 300 while the coatings grown at N ≥ 300 revealed anatase polycrystalline structure. The TiO₂ coatings bioactivity was evaluated by hydroxyapatite forming ability by the technique of soaking in Simulated Body Fluid (SBF). Correlation between bioactivity and structural properties of TiO₂ was determined. X-ray diffraction and scanning electron microscopy with electron probe microanalysis showed that amorphous TiO₂ coating did not induce the hydroxyapatite growth whereas anatase resulted in the hydroxyapatite forming on the samples surfaces which confirmed TiO₂ anatase bioactivity.     

Effect of N2 ion flux on the photocatalysis of nitrogen-doped titanium oxide films by electron-beam evaporation

Nitrogen-doped titanium oxide (TiO_xN_y) films were prepared with ion-assisted electron-beam evaporation. The nitrogen (N) incorporated in the film is influenced by the N₂ flux modulated by the N₂ flow rate through an ion gun. The TiO_xN_y films have the absorption edge of TiO₂ red-shifted to 500 nm and exhibit visible light-induced photocatalytic properties in the surface hydrophilicity and the degradation of methylene blue. The structures and states of nitrogen in the films are investigated by X-ray diffraction patterns (XRD), and X-ray photoelectron spectroscopy (XPS) and related to their visible light-induced photocatalytic properties. The results indicate that the substitutional N in anatase TiO₂ can induce visible light photocatalysis. The substitutional N is readily doped by the energetic nitrogen ions from the ion gun. The best photocatalytic activity is obtained at the largest N loading about 5.6 at.%, corresponding to the most substitutional N in anatase TiO₂. The film exhibits the degradation of methylene blue with a rate-constant (k) about 0.065 h⁻¹ and retaining 7° water contact angle on the surface under visible light illumination.     

The preparation of nitrogen-doped TiO2−xNx photocatalyst coated on hollow glass microbeads

In this paper, the effective method for nitrogen-doped TiO_2−xN_x photocatalyst coated on hollow glass microbeads is described, which uses titanium tetraisopropoxide [Ti(iso-OC₃H₇)₄] as the raw materials and gaseous ammonia as a heat treatment atmosphere. The effects of heat treatment temperature and time on the photocatalytic activity of TiO_2−xN_x/beads are studied. The photocatalyst is characterized by the UV-vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), Brunauer-Emmett-Teller (BET) analysis and scanning electron microscopy (SEM). The results show that when the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the photocatalytic activity of the TiO_2−xN_x/beads is the best. Compared with TiO₂, the photoabsorption wavelength range of nitrogen-doped TiO_2−xN_x red shifts of about 60 nm, and the photoabsorption intensity increases as well. The photocatalytic activity of the TiO_2−xN_x/beads is higher than that of the TiO₂/beads under visible light irradiation. The presence of nitrogen neither influences on the transformation of anatase to rutile, nor creates new crystal phases. When the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the amount of nitrogen-doped is 0.53 wt.% in the TiO_2−xN_x. As the density of TiO_2−xN_x/beads prepared is lower than 1.0 g/cm³, it may float on water surface and use broader sunlight spectrum directly.     

Pure and Nb-doped TiO1.5 films grown by pulsed-laser deposition for transparent p-n homojunctions

Pure and Nb-doped titanium oxide thin films were grown on sapphire substrates by pulsed-laser deposition in vacuum (10⁻⁷ mbar). The PLD growth leads to titanium oxide thin films displaying a high oxygen deficiency (TiO_1.5) compared with the stoichiometric TiO₂ compound. The structural and electrical properties (phase, crystalline orientation, nature and concentration of charge carriers, etc.) of these titanium oxide films were studied by XRD measurements and Hall effect experiments, respectively. The undoped TiO_1.5 phase displayed a p-type semiconductivity. Doping this titanium oxide phase with Nb⁵⁺ leads to an n-type behaviour as is generally observed for titanium oxide films with oxygen deficiency (TiO_x with 1.7 < x < 2). Multilayer homojunctions were obtained by the stacking of TiO_1.5 (p-type) and Nb-TiO_1.5 (n-type) thin films deposited onto sapphire substrates. Each layer is 75 nm thick and the resulting heterostructure shows a good transparency in the visible range. Finally, the I-V curves obtained for such systems exhibit a rectifying response and demonstrate that it is possible to fabricate p-n homojunctions based only on transparent conductive oxide thin films and on a single chemical compound (TiO_x).     

Effect of crystalline structure of TiO2 substrates on initial growth of atomic layer deposited Ru thin films

Ru thin films were grown on polymorphic TiO₂ thin film substrates at 230 and 250 °C by atomic layer deposition using 2,4-(dimethylpentadienyl)(ethylcyclopentadienyl)Ru and an O₂ gas. While the Ru films grown on amorphous and rutile TiO₂ substrates showed a relatively long incubation cycle number of approximately 350 and 100 at 230 and 250 °C, respectively, the Ru films grown on anatase TiO₂ substrates exhibited a significantly shorter incubation delay which was attributed to the catalytic activity of anatase TiO₂. This difference in the incubation cycle affected the surface morphology of the Ru films on different TiO₂ substrates.     

Optical and electric properties of Nb-doped anatase TiO2 single crystal

Nb-doped anatase TiO₂ single crystal has been grown by chemical vapour transport method. Raman spectra shows that the obtained crystal with Nb of 0.08 wt% has typical anatase structure. An absorption band was observed at around 2.2 eV, which seems to be due to the d-d transition in the conduction band. The electron paramagnetic resonance and electric resistivity measurements show that the doped niobium makes quite shallow donor level whose orbital is d_xy-like centered at the titanium position of anatase.     

Photocatalytic thin films containing TiO2:N nanopowders obtained by the layer-by-layer self-assembling method

In this work, TiO₂-N powders were synthesized by high-energy ball milling, using commercial titanium dioxide (TiO₂) in the anatase phase and urea to introduce nitrogen into TiO₂ in order to enhance their photocatalytic properties in the visible spectral region. Several samples were prepared by milling a mixture of TiO₂-urea during 2, 4, 8, 12 and 24 h and characterized by spectroscopic and analytical techniques. X-ray diffraction (XRD) results showed the coexistence of anatase and high-pressure srilankite TiO₂ crystalline phases in the samples. Scanning electron microscopy (SEM) revealed that the grain size of the powder samples decreases to 200 nm at 24 h milling time. UV-Vis diffuse reflectance spectroscopic data showed a clear red-shift in the onset of light absorption from 387 to 469 nm as consequence of nitrogen doping in the samples. The photocatalytic activity of the TiO₂-N samples was evaluated by methylene blue degradation under visible light irradiation. It was found that TiO₂-N samples had higher photocatalytic activity than undoped TiO₂ samples, which could be assigned to the effect of introducing N atoms and XPS results confirm it. Using polyethylenimine (PEI), transparent thin films of TiO₂-N nanoparticles were prepared by layer-by-layer self assembly method. UV-visible spectrophotometry was employed in a quantitative manner to monitor the adsorbed mass of TiO₂ and PEI after each dip cycle. The adsorption of both TiO₂ and PEI showed a saturation dip time of 15 min.     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 nanotubes

A series of Nd-TiO₂ powders have been prepared by the sol-gel technique with neodymium nitrate and tetra-n-butyl titanium as raw materials, and then Nd-TiO₂ nanotubes were fabricated by the hydrothermal method with a 10 mol l⁻¹ NaOH solution. The as-prepared Nd-TiO₂ nanotubes were characterized by TEM, XRD, DRS, and XPS, and their photocatalytic activity was also tested in the case of the degradation of methyl orange in water. TEM photograph showed that Nd-TiO₂ nanotubes were about 10-20 nm in diameter, with the lengths range from 100 to 300 nm. TiO₂ nanotubes contained anatase and rutile crystallites. However, 0.3% Nd-TiO₂ nanotubes contained anatase crystallites, and only little rutile crystallites, so it is shown that neodymium doping hindered the phase transformation from anatase into rutile. Nd doping increased the visible-light absorption ability of Nd-TiO₂ nanotubes, and a red shift for Nd-TiO₂ nanotubes appeared when compared to TiO₂ nanotubes. XPS analysis showed that two types of oxygen existed on the photocatalyst surface, including metal-O and hydroxyl group, and more hydroxyl group was on the surface of 2% Nd-TiO₂ nanotubes than on the surface of TiO₂ nanotubes. Nd doping enhanced the photocatalytic activities of Nd-TiO₂ nanotubes, and 0.3% Nd-TiO₂ nanotubes exhibited the highest photocatalytic activity.     

An XPS study on ion beam induced oxidation of titanium silicide

Titanium silicides (TiSi₂) films grown on Si(1 0 0) substrate were investigated by ex situ XPS depth profiling after athermal ion beam induced oxidation (IBO) at 12 keV O₂⁺ incident energy and normal incidence. The composition and stoichiometry of these films were quantitatively determined as chemical state relative concentrations versus sputter time. “In depth” silicon and titanium oxidation states have been obtained after spectra deconvolution, showing a mixture of silicon dioxide, titanium dioxide, titanium suboxides, elemental titanium and residual traces of titanium nitride. Thermochemical data based on the corresponding enthalpies of formation of the oxides cannot explain our experimental results as in the case of low energy IBO, an oxygen defective altered layer is formed, presenting features of a reduced TiO_x phase.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

A computational study on the adsorption and ring cleavage of para-chlorophenol on anatase TiO2 surface

In this work, a computational technique based on semiempirical SCF MO method MSINDO, has been used for investigation of the adsorption and photocleavage of para-chlorophenol (p-CP) molecule on the anatase TiO₂ (0 0 1) and (1 0 0) surfaces. The surfaces have been modeled with two saturated clusters Ti₂₁O₅₈H₃₂ and Ti₃₆O₉₀H₃₆. The optimization of the perpendicular conformation of p-CP molecule relative to the anatase TiO₂ (1 0 0) surface, has resulted in a linkage of the molecule to the surface titanium atom via phenolic oxygen atom. We studied the aromatic ring cleavage by singlet oxygen (¹O₂) and superoxide radical anion () and accordingly, relevant mechanisms are suggested. The results reveal that the ring opening path of p-CP molecule on TiO₂ (1 0 0) surface, following the single electron transfer/ mechanism, is energetically more favourable than the ¹O₂/dioxetane mechanism.     

Photoemission investigations on nanostructured TiO2 grown by cluster assembling

Nanostructured titanium dioxide (ns-TiO₂) films were grown by supersonic cluster beam deposition method. Transmission electron microscopy demonstrated that films are mainly composed by TiO₂ nanocrystals embedded in an amorphous TiO₂ phase while their electronic structure was studied by photoemission spectroscopy. The cluster assembled ns-TiO₂ films are expected to exhibit several structural and chemical defects owing to the large surface to volume ratio of the deposited clusters. Ultraviolet photoemission spectra (hv = 50 eV) from the valence band unveil the presence of a restrained amount of surface Ti 3d defect states in the band gap, whereas Ti 2p core level X-ray photoelectron (hv = 630 eV) spectra do not manifestly disclose these defects.     

Adsorption kinetics of alkanes on TiO2 nanotubesarray - structure-activity relationship

Presented are thermal desorption spectroscopy (TDS) measurements of iso-/n-butane adsorption on a variety of TiO₂ nanotubes (TiNTs) samples which are characterized by different crystal structures. The results are compared with a prior study on anatase(0 0 1) thin films grown on SrTiO₃(0 0 1). A distinct kinetic structure-activity relationship was present, i.e., the binding energies of the alkanes depend on the polymorph (anatase vs. mixed anatase/rutile) of TiO₂. A direct-fitting procedure of the TDS data has been applied to extract the kinetics parameters. The binding energies in the limit of zero coverage decrease as anatase thin film > amorphous-TiNTs ∼ polycrystalline anatase TiNTs > polycrystalline mixed anatase/rutile TiNTs.     

Characterization on titanium surfaces and its effect on photocatalytic bactericidal activity

Many studies have been published on the use of TiO₂ as a photocatalyst, which decomposes various organic compounds under UV illumination by generating various radicals. The purpose of the present study was to evaluate the photocatalytic bactericidal effects of variously treated titanium surfaces on Escherichia coli K-12. The specimens were fabricated from grade 4 commercially pure titanium, 12 mm in diameter and 1 mm in thickness. Five different surfaces were prepared (MA: machined surface; AO: anodized at 300 V; NO: NaOH-treated; NW: NaOH- and water-treated; and HT: heat-treated). Surface analysis was performed using scanning electron microscopy, optical interferometer, and thin-film X-ray diffractometry. Photocatalytic activity of each group was confirmed by degradation of methylene blue (MB). The antibacterial activity was assessed by calculating the survival ratio in a drop of a culture of E. coli placed on the surface under UV illumination. Significant photocatalytic activity and bactericidal effects were observed on the titanium surfaces of AO and NW, regardless of the surface roughness (P < 0.01). The group with anatase was the most susceptible to the photocatalytic effect, while the surface without anatase showed the least susceptibility. Based on this in vitro study, the crystallography of the oxide layer on its titanium surfaces is an important factor affecting the photocatalytic bactericidal activity.     

TiO2 activation using acid-treated vermiculite as a support: Characteristics and photoreactivity

Vermiculite was treated by sulfuric or nitric acid aqueous solutions with different concentration. These modified materials as the promising supports, were used to immobilize TiO₂. TiO₂ was prepared by the precursor, which was obtained by substituting partly isopropyl alcohol with Cl⁻ in titanium chloride {[Ti(IV)(OR)_nCl_m] (n = 2-3, m = 4 − n)}. The TiO₂/vermiculite composites were characterized by X-ray diffraction, scanning electron microscopy, and the nitrogen absorption. Their photocatalytic activity was evaluated by removal of methylene blue (MB). The pure anatase type crystalline phase was well deposited on the supports. The concentrations of acid for treatment had a significant influence on pore sizes and surface area of vermiculite. The treatment process changed microstructure of vermiculite, modified its characteristics, and farther improved the catalytic activity and absorption capacity of TiO₂/vermiculite composites. The treatment effect of nitric acid was superior to that of sulfuric acid.     

N incorporation and electronic structure in N-doped TiO2(1 1 0) rutile

We describe the growth and properties of well-defined epitaxial TiO_2−xN_x rutile for the first time. A mixed beam of atomic N and O radicals was prepared in an electron cyclotron resonance plasma source and Ti was supplied from a high-temperature effusion cell or an electron beam evaporator, depending on the required flux. A very high degree of structural quality is generally observed for films grown under optimized anion-rich conditions. N substitutes for O in the lattice, but only at the ∼1 at.% level, and is present as N³⁻. Epitaxial growth of TiO₂ and TiO_2−xN_x rutile prepared under anion-rich conditions is accompanied by Ti indiffusion, leading to interstitial Ti (Ti_i), which is a shallow donor in rutile. Our data strongly suggest that Ti_i donor electrons compensate holes associated with substitutional N²⁻ (i.e., Ti(III) + N²⁻ → Ti(IV) + N³⁻), leading to highly resistive or weakly n-type, but not p-type material. Ti 2p core-level line shape analysis reveals hybridization of N and Ti, as expected for substitutional N. Ti-N hybridized states fall in the gap just above the VBM, and extend the optical absorption well into the visible.     

Photocatalytic hydroxyapatite/titanium dioxide multilayer thin film deposited onto glass using an rf magnetron sputtering technique

Hydroxyapatite (HA)/titanium dioxide (TiO₂) thin film was deposited on glass using a radio frequency magnetron sputtering. X-ray diffraction (XRD), Fourier-transform infrared spectrometry, ultraviolet-visible spectroscopy and measurement of its photocatalytic activity by the decomposition of formaldehyde gas and the bacterial survival test of Escherichia coli (E. coli) cells were applied to characterize the film. After heat treatment (at 500 °C), XRD analysis of the HA/TiO₂ film showed a crystalline TiO₂ crystal structure with anatase phase. The transmittance of the HA/TiO₂ film decreased after the heat treatment, however, the average transmittance remained at 87% in the visible light range.In the decomposition of formaldehyde gas, the HA/TiO₂ film showed a higher decomposition rate than either the TiO₂ or the HA film alone. However, in the bacterial survival test, survival of cells on the HA/TiO₂ film was higher than that on the TiO₂ film, which indicates the HA/TiO₂ film has a lower bactericidal effect than the TiO₂ film alone.     

Visible-light-activated Ce-Si co-doped TiO2 photocatalyst

To enhance the visible photocatalytic activity and thermal stability of TiO₂, Ce-Si co-doped TiO₂ materials were synthesized through a nonaqueous method of which the purpose was to reduce the aggregation between TiO₂ particles. The obtained materials maintained anatase phase and large surface area of 103.3 m² g⁻¹ even after calcined at 800 °C. The XPS results also indicated that Si was weaved into the lattice of TiO₂, and Ce mainly existed as oxides on the surface of TiO₂ particles. The doped Si might enhance surface area and suppress transformation from anatase to rutile, while the doped Ce might cause visible absorption and inhibit crystallite growth during heat treatment. Evaluated by decomposing dye Rhodamine B, visible photocatalytic activity of Ce-Si co-doped TiO₂ was obviously higher than that of pure TiO₂ and reached the maximum at Ce and Si contents of 0.5 mol% and 10 mol%.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

A combined experimental and theoretical analysis of Fe-implanted TiO2 modified by metal plasma ion implantation

Photocatalyst titanium dioxide (TiO₂) thin films were prepared using sol-gel process. To improve the photosensitivity of TiO₂ at visible light, transition metal of Fe was implanted into TiO₂ matrix at 20 keV using the metal plasma ion implantation process. The primary phase of the Fe-implanted TiO₂ films is anatase, but X-ray diffraction revealed a slight shift of diffraction peaks toward higher angles due to the substitutional doping of iron. The additional band gap energy levels were created due to the formation of the impurity levels (Fe-O) verified by X-ray photoelectron spectroscopy, which resulted in a shift of the absorption edge toward a longer wavelength in the absorption spectra. The optical band gap energy of TiO₂ films was reduced from 3.22 to 2.87 eV with an increase of Fe ion dosages from 0 to 1 × 10¹⁶ ions/cm². The band gap was determined by the Tauc plots. The photocatalysis efficiency of Fe-implanted TiO₂ was assessed using the degradation of methylene blue under ultraviolet and visible light irradiation. The calculated density of states for substitutional Fe-implanted TiO₂ was investigated using the first-principle calculations based on the density functional theory. A combined experimental and theoretical Fe-implanted TiO₂ film was formed, consistent with the experimentally observed photocatalysis efficiency of Fe-implanted TiO₂ in the visible region.