Effect of hydrogenation vs. re-heating on intrinsic magnetization of Co doped In2O3

Influence of Co doping for In in In₂O₃ matrix has been investigated to study the effect on magnetic vs. electronic properties. Rietveld refinement of X-ray diffraction patterns confirmed formation of single phase cubic bixbyite structure without any parasitic phase. Photoelectron spectroscopy and refinement results further revealed that dopant Co²⁺ ions are well incorporated at the In³⁺ sites in In₂O₃ lattice and also ruled out formation of cluster in the doped samples. Magnetization measurements infer that pure In₂O₃ is diamagnetic and turns to weak ferromagnetic upon Co doping. Hydrogenation further induces a huge ferromagnetism at 300 K that vanishes upon re-heating. Experimental findings confirm the induced ferromagnetism to be intrinsic, and the magnetic moments to be associated with the point defects (oxygen vacancies V_o) or bound magnetic polarons around the dopant ions.     

Comment on “Effect of annealing temperature on structure, magnetic properties and optical characteristics in Zn0.97Cr0.03O nanoparticles” by Liu et al., [Appl. Surf. Sci. 256 (2010) 3559]

The authors of a recent paper (Appl. Surf. Sci. 256 (2010) 3559) studied the effect of annealing temperature on structural, magnetic and optical properties in Cr-doped zinc oxide (Zn_0.97Cr_0.03O) nanoparticles synthesized by sol-gel method. The authors have verified that Cr ions, in 3+ valence state, substitute the Zn ions in the ZnO lattice. They concluded that the ferromagnetism observed in the samples is an intrinsic property of the Cr-doped ZnO. However, we noticed an unusual point in this article. The Cr 2p XPS spectrum shown by them is against the general trend of the 2p XPS spectra of the transition metals. In this light, we re-measured the high-resolution 2p XPS spectrum of Cr for a 3% Cr-doped ZnO sample that is entirely different than theirs. The spectrum presented by them therefore demands proper interpretations or it might mislead the researchers in this developing field.     

Fe/Al2O3/Fe隧道结特性分析

用离子束溅射方法制备磁性隧道结(MTJ). 研究MTJ样品的隧道结磁电阻(TMR)效应.用X射线 光电子能谱分析了MTJ的软、硬磁层和非磁层及其界面的化学组成与微结构.研究了MTJ的微 结构对氧化铝势垒高度与有效宽度和TMR效应的影响. 关键词： 磁性隧道结 X射线光电子能谱 隧道结磁电阻     

P-n codoping induced enhancement of ferromagnetism in Mn-doped In2O3: A first-principles study

We have performed first-principles density functional theory calculation in order to investigate the feasibility of “p-n codoping method” in improving magnetic property of In₂O₃ based diluted magnetic semiconductors. We find that the ferromagnetic state is favored in Mn-doped In₂O₃, and Sn doping can increase magnetic moment in Mn-doped In₂O₃. These findings are in line with our earlier experimental observation. Along with previous works, we now have enough evidences to support that p-n codoping is a valid method to improve magnetism of oxides based diluted magnetic semiconductors.     

Generation of oxygen vacancies in the surface of ferroelectric Pb(Nb,Zr,Ti)O3

Controlled generation of oxygen vacancies in the surface of ferroelectric thin films is crucial to study how surface reduction affects molecular adsorption and catalysis of gas-surface phenomena. We demonstrate the effective reduction in the surface of 4% niobium doped 20/80 PZT (PNZT) thin films. The sample was characterized by X-ray diffraction (XRD), Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), and heated at 200, 250 and 300 °C in a high vacuum system at 10⁻⁵ T of H₂. Auger peak-to-peak intensities was used to study the elemental concentrations during the reduction experiment. High-resolution XPS spectra were acquired before and after reduction process for detecting the changes of the oxygen signal. Vacancies production rates as slow as 0.21% per minute were achieved and the temperature was not a key parameter in the process. Experiments at higher hydrogen pressures and lower temperatures might improve the control of the vacancies production.     

Role of point defects on conductivity, magnetism and optical properties in In2O3

In order to assess the effects of point defects including transition metal doping on its electronic structure, the self-consistent band structure of the transparent oxide In₂O₃ (in the Ia₃ structure) has been calculated with oxygen vacancies, oxygen and indium interstitial atoms and several transition metal dopants using density functional theory based first principles calculations. An oxygen vacancy alone does not act as a strong native donor but when combined with interstitial indium and (substitutional) transition metal doping, shallow donor levels close to the conduction band are formed. Spin polarized calculations show measurable magnetism in some of the transition metal doped systems while the dielectric functions indicate whether such systems remain transparent among other things.     

X-ray photoelectron spectroscopy studies of Co-doped ZnO-Ga2O3-SiO2 nano-glass-ceramic composites

Co-doped ZnO-Ga₂O₃-SiO₂ nano-glass-ceramic composites were prepared by sol-gel method. X-ray diffraction patterns showed that the crystallization temperature was 800 °C. X-ray photoelectron spectroscopy (XPS) was used to study the effect of heat-treatment temperature on the electronic structure of Co-doped ZnO-Ga₂O₃-SiO₂ nano-glass-ceramic composites. The Zn (2p_3/2), Ga (2p_3/2) and O (1s) XPS spectra for the glass-ceramics heat-treated at 800-1000 °C could be deconvoluted into two peaks corresponding to these elements in glass network and in nanocrystals, respectively. The results indicate that the material is composed of an amorphous silicate network and ZnGa₂O₄ nanocrystalline particles. The amount of nanocrystals increases with the annealing temperature. The photoelectron peak of Si (2p) shifts to higher binding energy at higher annealing temperature, revealing the charge transfer from Si to O increased. The relationship between the microstructure of Co-doped ZnO-Ga₂O₃-SiO₂ sample and its absorption properties was discussed, and the suitable heat-treatment temperature was proposed.     

Luminescence characterization and electron beam induced chemical changes on the surface of ZnAl2O4:Mn nanocrystalline phosphor

Luminescence characteristics and surface chemical changes of nanocrystalline Mn²⁺ doped ZnAl₂O₄ powder phosphors are presented. Stable green cathodoluminescence (CL) or photoluminescence (PL) with a maximum at ∼512 nm was observed when the powders were irradiated with a beam of high energy electrons or a monochromatic xenon lamp at room temperature. This green emission can be attributed to the ⁴T₁ → ⁶A₁ transitions of the Mn²⁺ ion. Deconvoluted CL spectra resulted in two additional emission peaks at 539 and 573 nm that may be attributed to vibronic sideband and Mn⁴⁺ emission, respectively. The luminescence decay of the Mn²⁺ 512 nm emission under 457 nm excitation is single exponential with a lifetime of 5.20 ± 0.11 ms. Chemical changes on the surface of the ZnAl₂O₄:Mn²⁺ phosphor during prolonged electron beam exposure were monitored using Auger electron spectroscopy. The X-ray photoelectron spectroscopy (XPS) was used to determine the chemical composition of the possible compounds formed on the surface as a result of the prolonged electron beam exposure. The XPS data suggest that the thermodynamically stable Al₂O₃ layer was formed on the surface and is possibly contributing to the CL stability of ZnAl₂O₄:Mn phosphor.     

Characterization of interface between CuInSe2 and In2O3

CuInSe₂/In₂O₃ structures were formed by depositing CuInSe₂ films by stepwise flash evaporation onto In₂O₃ films, which were grown by DC reactive sputtering of In target in presence of (Ar+O₂) gas mixture. Phase purity of the CuInSe₂ and In₂O₃ films was confirmed by Transmission Electron Microscopy (TEM) studies. X-ray diffraction (XRD) results on CuInSe₂/In₂O₃/glass structures showed sharp peaks corresponding to (112) plane of CuInSe₂ and (222) plane of In₂O_3. Rutherford Backscattering Spectrometry (RBS) investigations were carried out on CuInSe₂/In₂O₃/Si structures in order to characterize the interface between In₂O₃ and CuInSe₂. The results show that the CuInSe₂ films were near stoichoimetric and In₂O₃ films had oxygen deficient composition. CuInSe₂/In₂O₃ interface was found to include a ∼20 nm thick region consisting of copper, indium and oxygen. Also, the In₂O₃/Si interface showed the formation of ∼20 nm thick region consisting of silicon, indium and oxygen. The results are explained on the basis of diffusion/reaction taking place at the respective interfaces.     

Electronic structure analysis of Mn- and Fe-codoped In2O3 by photoemission yield measurements

The valence band electronic structures of Mn- and/or Fe-doped In₂O₃, i.e., In₂O₃:Mn, In₂O₃:Fe, and In₂O₃:(Mn, Fe), are investigated by photoemission yield measurements. Significant changes are observed in the threshold energy of photoemission, depending on the doped magnetic ions, which indicates that an additional occupied band appears above the top of the valence band of In₂O₃ owing to doping with Mn and/or Fe ions. It is confirmed that the order of the threshold energies of photoemission, E_PET, is E_PET(In₂O₃:Mn)<E_PET(In₂O₃:(Mn, Fe))<E_PET(In₂O₃:Fe)<E_PET(In₂O₃). To gain a better understanding of these results, first-principles molecular orbital calculations are also carried out, which successfully explain the observed changes in the photoemission threshold energies.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

Electronic structure of non-centrosymmetric AgCd2GaS4 and AgCd2GaSe4 single crystals

X-ray photoelectron core-level and valence-band spectra for pristine and Ar⁺-ion irradiated (0 0 1) surfaces of AgCd₂GaS₄ and AgCd₂GaSe₄ single crystals grown, respectively, by the Bridgman method and the method of direct crystallization have been measured in the present work. The X-ray photoelectron spectroscopy (XPS) results reveal high chemical stability of (0 0 1) surfaces of AgCd₂GaS₄ and AgCd₂GaSe₄ single crystals. Electronic structure of AgCd₂GaS₄ has been calculated employing the full potential linearized augmented plane wave method. For the AgCd₂GaS₄ compound, the X-ray emission bands representing the energy distribution of the valence Ag d-, Cd d-, Ga p- and S p-like states were recorded and compared on a common energy scale with the XPS valence-band spectrum. The theoretical and experimental data regarding the occupation of the valence band of AgCd₂GaS₄ were found to be in excellent agreement to each other. Second harmonic generation (SHG) efficiency of AgCd₂GaS₄ by using the 320 ns CO laser at 5.5 μm has been recorded within the temperature range 80–300 K. Substantial increase of the photoinduced SHG which in turn is substantially dependent on the temperature has been detected for the AgCd₂GaS₄ compound.     

Synthesis and characterization of room-temperature ferromagnetism in Fe- and Ni-co-doped In2O3

Observation of room-temperature ferromagnetism in Fe- and Ni-co-doped In₂O₃ samples (In_0.9Fe_0.1−xNi_x)₂O₃ (0?x?0.1) prepared by citric acid sol-gel auto-igniting method is reported. All of the samples with intermediate x values are ferromagnetic at room-temperature. The highest saturation magnetization (0.453 μ_B/Fe+Ni ions) moment is reached in the sample with x=0.04. The highest solubility of Fe and Ni ions in the In₂O₃ lattice is around 10 and 4 at%, respectively. The 10 at% Fe-doped sample is found to be weakly ferromagnetic, while the 10 at% Ni-doped sample is paramagnetic. Extensive structure including Extended X-ray absorption fine structure (EXAFS), magnetic and magneto-transport including Hall effects studies on the samples indicate the observed ferromagnetism is intrinsic rather than from the secondary impurity phases.     

R型铁氧体BaFe4-xTi2+xO11的化学组态以及磁性行为的研究

本文通过传统的固相反应法制备了R型六角铁氧体BaFe_4-xTi_2+xO₁₁ (x= 0, 0.25, 0.5, 0.75, 1), 并且对它的原子价态以及磁性行为进行了研究. X 射线光电子能谱(XPS)结果显示了随着掺杂含量的增加, 体系中Fe³⁺离子逐渐减少而Fe²⁺离子逐渐增加. 由于具有非对称结构的阻挫晶格中存在各种关联作用的竞争, 使得BaFe_4-xTi_2+xO₁₁体系表现出了复杂的磁有序行为, 在T₁～250 K和T₂～83 K两处存在磁转变. 对这一系列掺杂样品, 在相变温度T₁之上表现顺磁行为, 而在相变温度T₂前后的磁化强度都表现出低场下随磁场的增加快速增加, 高场下则线性变化且在5×10⁴ Oe时还未达到饱和的行为, 表明这一系列掺杂样品是典型的倾斜反铁磁态(canted antiferromagnetic) 或者亚铁磁态.     

Surface termination, composition and reconstruction of Fe3O4(001) and γ-Fe2O3(001)

We address a current controversy concerning the nature of the surfaces of Fe₃O₄(001) and γ-Fe₂O₃(001) grown on MgO(001) by molecular beam epitaxy. Despite recent claims to the contrary, we show that γ-Fe₂O₃(001) unambiguously exhibits a (1×1) surface net, in contrast to Fe₃O₄(001), which assumes a R45 reconstruction. In addition, we present high-energy-resolution Fe 2p and O 1s core-level photoelectron spectra obtained at both normal and grazing emission for γ-Fe₂O₃(001) and Fe₃O₄(001). These spectra show that the Fe₃O₄(001) surface has a higher Fe(III)/Fe(II) ratio than the bulk, and that the asymmetry in the O 1s line shape for Fe₃O₄(001) is due to final state effects rather than the presence of a surface oxygen or hydroxyl species.     

Weak ferromagnetism in BiFeO3 doped with titanium

The Bi_1−xA_xFe_1−xTi_xO₃ (A—Ca, Sr, Pb, Ba) and BiFe_1−xTi_xO_3+δ systems have been studied using X-ray, neutron powder diffraction and magnetization measurements in a magnetic field up to 14 T. It was found that all Bi_1−xA_xFe_1−xTi_xO₃ solid solutions are rhombohedral up to x=0.3. In the case of BiFe_1−xTi_xO_3+δ the rhombohedral distortion preserved up to x=0.11. A homogeneous weakly ferromagnetic state was found for Bi_1−xCa_xFe_1−xTi_xO₃ (0.15≤x≤0.25) and BiFe_1−xTi_xO_3+δ (0.06≤x≤0.11), probably due to magnetoelectric interactions, whereas Bi_1−xA_xFe_1−xTi_xO₃ (A—Sr, Pb, Ba) compounds above doping level x>0.1 seem to be collinear antiferromagnets.     

Surface chemistry of Fe2O3 nanoparticles on ultrathin oxide layers on Si and Ge

In this paper, we report on a comparative study of the effect of Fe₂O₃ nanoparticles (NP), introduced onto a thin oxide layer formed on silicon and germanium surfaces, on the thermal decomposition pathway of the individual oxide layers. On both the surfaces, NP of Fe₂O₃ undergo a reduction reaction through a bonding partner change reaction, where the oxygen atoms change from Fe to Si or Ge. On both the surfaces, annealing results in the conversion of the suboxide-like species to dioxide-like species (SiO_x to SiO₂ and GeO_x to GeO₂ respectively for Si and Ge surfaces), until the oxide layer decomposes following the desorption of the respective monoxide species (SiO and GeO). Both the Si and Ge corelevels show a larger chemical shift (4.1 and 3.51 eV in Si 2p and Ge 3d corelevels, respectively) for the as-prepared oxide samples with the NP, at room temperature compared to that without the NP (3.7 and 3.4 eV), indicating a catalytic enhancement of the dioxide formation. Selective formation of silicon oxides leads to encapsulation of the nanoparticles and acts like a protective layer, preventing the oxidation of Fe.     

Experimental and theoretical study of the electronic properties of CoSi2 and NiSi2

Electronic structure of Co and Ni silicides were studied by means of the spectral properties of XPS high-resolution measurements together with theoretical calculations using crystal orbital overlap population (COOP) analysis. Calculations were carried out for CoSi₂ and NiSi₂ microstructures. Analysis from calculations shows that hybridization is stronger in Co disilicide than in Ni disilicide. Close to the Fermi level, we noticed that for the Co disilicide there is a small distribution (bonding and antibonding) to the total COOP, while the contribution from the Ni disilicide is null. XPS analysis of sample under study gives evidence about the covalent bonding when the chemical shifts for the Co 2p_3/2, Ni 2p_3/2 and Si 2p transitions are analyzed in the depth-profile mode.