Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

Structural, optical and electrochemical properties of TiO2 thin films grown by APCVD method

Atmospheric pressure chemical vapor deposition (APCVD) of TiO₂ thin films has been achieved onto glass and onto ITO-coated glass substrates, from the reaction of TiCl₄ with ethyl acetate (EtOAc). The effect of the synthesis temperature on the optical, structural and electrochemical properties was studied through spectral transmittance, X-ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS) measurements. It was established that the TiO₂ films deposited onto glass substrate, at temperatures greater than 400 °C grown with rutile type tetragonal structure, whereas the TiO₂ films deposited onto ITO-coated glass substrate grown with anatase type structure. EIS was applied as suitable method to determine the charge transfer resistance in the electrolyte/TiO₂ interface, typically found in dye-sensitized solar cells.     

Titania surface modification and photovoltaic characteristics with tungsten oxide

WO₃-coated TiO₂ film was prepared by depositing TiO₂ suspension containing small amounts of ammonium tungstate solution. The morphology and structure of the samples were characterized with high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and photoluminescence (PL) emission spectrum. The results showed that WO₃ formed a coating layer on surface of TiO₂ and significantly reduced the surface traps of TiO₂ nanoparticles. Transient photovoltage and electrochemical impedance measurements (EIS) were employed to study the charge separation/recombination process. The results revealed that the charge recombination was greatly retarded and the electron lifetime was increased due to the coating layer of WO₃. These observations showed good correlation with current-voltage analyses of dye-sensitized solar cell fabricated from these films, with WO₃ overlayer resulting in an increase in open-circuit voltage of up to 37 mV and 11% improvement in overall device efficiency.     

Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

TiO₂ nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO₂ nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO₂ nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO₂ mass weight, respectively, and the linkage between DBS groups and TiO₂ surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO₂ obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO₂ is also related to the increase in the capability for adsorbing RhB.     

Electrochemical properties of TiO2 nanoparticle/nanorod composite photoanode for dye-sensitized solar cells

A unique composite of TiO₂ nanoparticles (NPs) and nanorods (NRs) has been used to fabricate a photoelectrode for developing dye-sensitized solar cells (DSSCs) with higher sensitivity. The TiO₂ nanorods were synthesized using a mechanical process, in which electrospun TiO₂ nanofibers was grinded in a controlled way to obtain uniform size distribution. The characteristics of electron transport, recombination lifetime and charge collection were investigated by intensity-modulated photocurrent spectroscopy (IMPS) and intensity-modulated photovoltage spectroscopy (IMVS). Photoelectrodes prepared with the composites of NRs and NPs showed significant improvements in electron transportation compared to only NP photoelectrodes, which would enhance the photovoltaic performance of DSSCs. IMPS and IMVS measurements show that fast electron transport and slightly decreased recombination lifetime resulted in the improvement of efficiency. The highest energy conversion efficiency obtained from the photoelectrodes fabricated with the as-prepared rutile TiO₂ nanofibers at 5 wt% NR content was up to 6.1% under AM1.5G solar illumination. The results demonstrate that the composite nanostructure can take advantage of both the fast electron transport of the nanorods and the high surface area of the nanoparticles.     

The Dynamic Resistance of CdS/CdSe/ZnS Co-Sensitized TiO2 Solar Cells

Quantum dots' sensitized solar cells (QDSSCs) can create the high-performance and low-cost photovoltaic in the future. In this study, we synthesized the film of TiO₂/CdS/CdSe/ZnS photoanodes by successive ionic layer adsorption reaction (SILAR) method. The absorption spectra, photoluminescent spectra and electrochemical impedance spectra (EIS) of the film TiO₂/CdS/CdSe/ZnS photoanodes show that the structure of energy levels in the conduction band (CB) of photoanode materials CdS, CdSe, and ZnS quantum dots (QDs) can absorb a great number of photons in each region and inject stimulated electrons quickly into the conduction band (CB) of TiO₂. Furthermore, we also studied the influence of the SILAR cycles on the dynamic resistance, the lifetime of electrons in QDSSCs through Nyquist and Bode.     

Enhancement of photocatalytic degradation of polyethylene plastic with CuPc modified TiO2 photocatalyst under solar light irradiation

Solid-phase photocatalytic degradation of polyethylene (PE) plastic, one of the most common commercial plastic, over copper phthalocyanine (CuPc) modified TiO₂ (TiO₂/CuPc) photocatalyst was investigated in the ambient air under solar light irradiation. Higher PE weight loss rate, greater texture change; more amount of generated CO₂, which is the main product of the photocatalytic degradation of the composite PEC plastic can be achieved in the system of PE-(TiO₂/CuPc) in comparison with PE-TiO₂ system. The CuPc promoted charge separation of TiO₂ and enhanced the photocatalytic degradation of PE based on the analysis of surface photovoltage spectroscopy (SPS). During the photodegradation of PE plastic, the reactive oxygen species generated on TiO₂ or TiO₂/CuPc particle surfaces play important roles. The present study demonstrates that the combination of polymer plastic with TiO₂/CuPc composite photocatalyst in the form of thin film is a practical and useful way to photodegrade plastic contaminants under solar light irradiation.     

纳米TiO2颗粒/亚微米球多层结构薄膜内电荷传输性能研究

本文主要利用TiO₂亚微米球较强的光散射特性设计了纳米TiO₂颗粒/亚微米球多层结构光阳极, 并借助强度调制光电流谱(intensity-modulated photocurrent spectroscopy)、电化学阻抗谱(electrochemical impedance spectroscopy)和入射单色光光电转化效率(incident photon-to-current conversion efficiency), 研究亚微米球的引入对多层结构薄膜内缺陷态、电子传输时间、电子收集效率和界面电荷转移性能的影响. 强度调制光电流谱反映出亚微米球表面缺陷态少, 但其颗粒间接触不紧密, 导致在接触部位形成了势垒, 阻碍了电子的传输, 导致电子传输时间增长. 电化学阻抗谱结果表明不同多层结构电池界面复合无明显差别, 同时底层采用纳米TiO₂ 透明薄膜结构的电池, 其光利用率要明显高于底层采用亚微米球薄膜结构的电池, TiO₂费米能级电子填充水平也相对增大, 使得电池的光电转换效率得到提升. 多层结构复合薄膜电荷传输和光伏特性的研究, 为高效染料敏化太阳电池光阳极设计提供了实验基础.     

FT-IR study of the photocatalytic degradation of gaseous toluene over UV-irradiated TiO2 microballs: enhanced performance by hydrothermal treatment in alkaline solution

In this study, photocatalysts of TiO₂ microballls were obtained via a hydrothermal treating of commercial P25 in alkaline solution, and then characterized with SEM, XRD, BET, DRS and surface photovoltage spectroscopy (SPS) techniques. The photovoltage response of the prepared TiO₂ microballs on spectrum features a quantum size effect brought about by the reduced grain size with respect to the precursor. The UV-assisted photodegradation of gaseous toluene over P25 and the prepared TiO₂ microballs was monitored by an in situ infrared technique. The results demonstrated that the prepared TiO₂ microballs in anatase form were more active than commercial P25 in photocatalytic oxidation of gaseous toluene. The promoted activity of the hydrothermal-treated TiO₂ is attributed to the increasing specific surface area and larger band gap induced by the reduced crystallite size.     

The role of W doping in response of hydrogen sensors based on MAO titania films

Anatase TiO₂ and W doped TiO₂ films were fabricated by micro-arc oxidation (MAO) on titanium substrates and their hydrogen sensing properties were investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the oxide films and electrochemical impedance spectroscopy (EIS) was applied to investigate the gas sensing mechanism. It is found that the conductivity of TiO₂ films varies with the introduction of W dopant. EIS analysis reveals that the grains and especially the grain boundaries are mainly contributed to the hydrogen response and their equivalent circuits could be represented electrochemically by parallel resistor and constant phase element (CPE). The enhanced sensor signal at higher measuring temperature (300 °C) is observed with an optimal doping concentration of W ions (1.81 at.%).     

Preparation of nanocrystalline Sn-TiO2−X via a rapid and simple stannous chemical reducing route

The Sn-TiO_2−X nanoparticles have been prepared via a rapid and simple stannous chemical reducing method. The as-prepared Sn-TiO_2−X nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), XPS, and DRS technology as well as photocatalytic degradation of RhB were studied under illumination. The experiment results revealed that the reduction of the TiO₂ particles raised their Fermi level, which can enhance the driven force of photoinduced electrons transferring from TiO₂ to adsorbed O₂ and SnO₂ on the surface of TiO₂. On the other hand, the amount of oxygen vacancies of the Sn-TiO_2−X increased after the stannous chemical reduction. The oxygen vacancies can also effectively inhibit the recombination of photoinduced electrons and holes pairs. These factors are favorable to the photocatalytic reaction.     

Photodegradation of CH3I on mesoporous TiO2-B nanofibers with Au nanoparticles

Au nanoparticles deposited on mesoporous TiO₂-B nanofibers have been prepared, characterized, and used to catalyze photoreactions of iodomethane. High-density gold-particle deposition on TiO₂-B is obtained by electrostatic and/or chemical force between the particles of TiO₂-B and Au capped with -SC(H)(CO₂H)(CH₂CO₂H) through pH control. The capping groups on the gold particles can be removed after 400 °C calcination. It is found that the nature of the inorganic acids used for pH adjustment has effects on particle morphology and deposition. Two other methods, i.e., preparation of TiO₂-B nanofibers in the presence of gold particles and preparation of gold nanoparticles in the presence of TiO₂-B particles (deposition-precipitation method), are also investigated. However, the former method produces a low-density deposition and the latter one induces a morphology change of the TiO₂-B and an increase of the Au in size. Fourier transform infrared spectroscopy has been employed to study and to compare the photoreactions of CH₃I on TiO₂-B and Au/TiO₂-B and the effect of O₂. The presence of gold particles on TiO₂-B increases the efficiency of CH₃I photodegradation, forming adsorbed methoxy and formate. The role of gold is also discussed.     

Effect of CdS modification on photoelectric properties of TiO2/PbS quantum dots bulk heterojunction

TiO₂/PbS(CdS) quantum dots (QDs) bulk heterojunction has been fabricated by successive ionic layer adsorption and reaction method via alternate deposition of PbS and CdS QDs. In comparison with TiO₂/PbS heterojunction, the incident photon to current conversion efficiency was increased almost 50% in the visible region. Meantime, the short-circuit current and open-circuit voltage were enhanced 200% and 35% respectively. The influence mechanism of CdS is related to reduction of trap state density at TiO₂/PbS interface and PbS QDs surface by the discussion of the dark current density–voltage curves, the transient photocurrent response curves and the electrochemical impedance spectra spectroscopy (EIS).     

Study on the mechanisms of photoinduced carriers separation and recombination for Fe-TiO2 photocatalysts

The iron(III)-ion doped TiO₂ (Fe³⁺-TiO₂) with different doping Fe³⁺ content were prepared via a sol-gel method. The as-prepared Fe³⁺-TiO₂ nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), field-induced surface photovoltage spectroscopy (FISPS), and the photoelectrochemical properties of Fe³⁺-TiO₂ catalysts with different Fe³⁺ content are performed by electrical impedance spectroscopy (EIS) as well as photocatalytic degradation of RhB are studied under illuminating. Based on the experiment results, the mechanism of photoinduced carriers separation and recombination of Fe³⁺-TiO₂ was revealed: that is, the Fe³⁺ captures the photoinduced electrons, inhibiting the recombination of photoinduced electron-hole pairs, this favors to the photocatalytic reaction at low doping concentration (Fe/Ti ≤ 0.03 mol%); while Fe³⁺ dopant content exceeds 0.03 mol%, Fe₂O₃ became the recombination centers of photoinduced electrons and holes because of that the interaction of Fe₂O₃ with TiO₂ leads to that the photoinduced electrons and holes of TiO₂ transfer to Fe₂O₃ and recombine quickly, which is unfavorable to the photocatalytic reaction.     

Natural dye-based photoelectrode for improvement of solar cell performance

In the present paper, photovoltaic studies of dye-sensitized solar cells (DSSCs) based on betacyanin/TiO₂ and betacyanin/WO₃–TiO₂ have been done. The cell performances were compared through I–V curves and wavelength dependant photocurrent measurements for the two new types of DSSCs. The TiO₂-coated DSSC showed the photovoltage and photocurrent of 300 mV and 4.96 mA/cm², whereas the cell employing WO₃–TiO₂ photoelectrode showed the values 435 mV and 9.86 mA/cm², respectively. The conversion efficiency of TiO₂ based dye-sensitized solar cell was found to be 0.69 %, while WO₃–TiO₂-based cell exhibited a higher conversion efficiency of 2.2 %. The better performance of the WO₃–TiO₂ dye-sensitized solar cell photoelectrode is thought to be due to an inherent energy barrier at the electrode/electrolyte interface leading to the reduced recombination of photoinduced electrons.     

Influence of TiO2 nanotube morphology and TiCl4 treatment on the charge transfer in dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) were fabricated using TiO₂ nanoparticles (NPs), TiO₂ nanotube arrays (NTAs), and surface-modified NTAs with a TiCl₄ treatment. The photovoltaic efficiencies of the DSSCs using TiO₂ NP, NTA, and TiCl₄-treated NTA electrodes are 4.25, 4.74, and 7.47 %, respectively. The highest performance was observed with a TiCl₄-treated TiO₂ NTA photoanode, although in the case of the latter two electrodes, the amounts of N719 dye adsorbed were similar and 68 % of that of the NP electrode. Electrochemical impedance measurements show that the overall resistance, including the charge–transfer resistance, was smaller with NTA morphologies than with NP morphologies. We suggest that a different electron transfer mechanism along the one-dimensional nanostructure of the TiO₂ NTAs contributes to the smaller charge–transfer resistance, resulting in a higher short circuit current (J _sc), even at lower dye adsorption. Furthermore, the TiCl₄-treated NTAs showed even smaller charge–transfer resistance, resulting in the highest J _sc value, because the downward shift in the conduction band edge improves the electron injection efficiency from the excited dye into the TiCl₄-treated TiO₂ electrodes.     

Ultrasound-assisted synthesis of unzipped multiwalled carbon nanotubes/titanium dioxide nanocomposite as a promising next-generation energy storage material

Carbon-based systems have been discussed as prospective alternatives for conventional metal-based catalysts over the past decade. These studies were motivated by the abundance, low cost, lightweight and diversity of structural allotropes of carbon. We reported here the synthesis of a new type of unzipped multiwalled carbon nanotubes/titanium dioxide (UzMWCNT/TiO₂) nanocomposite by the two-stage procedure. By the modified Hummers method, multiwalled carbon nanotubes (MWCNTs) were converted to oxidized multi-walled carbon nanotubes (O-MWCNT). Then, through a facile ultrasound-assisted route prepared UzMWCNT/TiO₂ nanocomposite. For this, the oxidized multiwalled carbon nanotubes are treated with TiCl₄ under an ultrasonic probe for 3 h to generate UzMWCNT/TiO₂ and then explored its environmental friendliness and energy applications as a supercapacitor. This novel UzMWCNT/TiO₂ nanocomposite was characterized using XRD, TGA, FT-IR, Raman, TEM and EDX analysis. The electrochemical performance can be evaluated by using cyclic voltammetry (CV) and galvanostatic charging-discharging (GCD) study. Finally, the electrodes prepared using UzMWCNT/TiO₂ nanocomposite have been analyzed through electrochemical impedance spectroscopy (EIS) to probe the charge transfer characteristics and the results are consistent with other electrochemical measurements.     

Studies of photo-induced charge transfer properties of ZnWO4 photocatalyst

Different sizes of ZnWO₄ photocatalysts were synthesized by a hydrothermal method. The as-prepared sample shows highly efficient photocatalytic activity for the degradation of RhB under UV irradiation, which significantly vary with the increase of the hydrothermal temperatures. Surface photovoltage spectrum (SPS), field-induced surface photovoltage spectrum (FI-SPS) and surface photovoltage transient (TPV) techniques are used to investigate the detailed photoinduced charge transfer behavior. Results indicate that the ZnWO₄ synthesized at 413 K possess the largest BET surface area and the abundant donor surface states which are assumed to inhibit the recombination of the photogenerated electron-hole pairs, and thus a significant enhancement in the reaction rate is observed.     

Cocktail effect of Fe2O3 and TiO2 semiconductors for a high performance dye-sensitized solar cell

The bi-semiconductors of TiO₂ and Fe₂O₃ were used as a photoelectrode material in a high performance dye-sensitized solar cell due to cocktail effects from the two conduction bands. The size of the semiconductors was reduced by using a paint shaker to enlarge the contact area of the semiconductor with the dye or electrolyte. The fill factor and the efficiency of the prepared dye-sensitized solar cell were improved by over 16% and 300%, respectively; these parameters were measured from a current-voltage curve that was based on the effects of the Fe₂O₃ co-semiconductor and the size reduction. A mechanism is suggested wherein the conduction band of Fe₂O₃ works to prohibit the trapping effects of electrons in the conduction band of TiO₂. This result is attributed to the prevention of electron recombination between electrons in the TiO₂ conduction band with dye or electrolytes. The mechanism is suggested based on impedance results, which indicate improved electron transport at the interface of the TiO₂/dye/electrolyte.