Metal Precursor Influence on Performance of CuIn1-xGaxSe2 Films

在镀有Mo的纳钙玻璃衬底上顺序溅射沉积CuGa/In/CuGa层,然后在真空下520 oC硒化40 min,制备成CIGS薄膜. 通 过调整预制层的底层和表层的溅射沉积CuGa层的厚度比,制备不同的CIGS薄膜. 通过X射线衍射谱、拉曼谱、电子能谱、平面和断面SEM的分析, 揭示出CIGS薄膜是黄铜矿相的结构, 晶粒0.5～2 μm,且由硒化CuGa/In/CuGa厚度比为7:20:3的金属预制层后的CIGS薄膜的结晶性最好. 拉曼光谱表明,没有In-Se二元化合物相和有序缺陷化合物相.     

Cu元素对Cu(In,Ga)Se_2薄膜及太阳电池的影响

Cu元素成分对Cu(In,Ga)Se2(简称CIGS)薄膜材料的电学性质及其电池器件性能有很重要的影响.本文利用蒸发法制备了贫Cu和富Cu的CIGS吸收层(0.7Cu/(Ga+In)1.15)及相应的电池器件.扫描电镜和Hall测试发现,富Cu材料的结构特性(晶粒大、结晶状态好)和电学特性(电阻率低、迁移率高等)优于贫Cu材料,而性能测试表明贫Cu器件的效率优于富Cu器件.变温性能测试分析表明,贫Cu器件的主要复合路径是体复合,激活能与CIGS禁带宽度相当;富Cu器件的主要复合路径是界面复合,其激活能远小于CIGS禁带宽度,这大大降低了开路电压Voc,从而降低了电池效率.最后利用蒸发三步法制备了体材料稍富Cu表面贫Cu的CIGS吸收层,降低了短路电流和开路电压的损失,获得了超过15%的电池效率.     

热裂解活化硒对CIGS太阳电池开路电压的影响

考察了通过自主研发的高温热裂解辅助硒化装置所产生的高活性硒对CIGS薄膜结构和器件性能的影响.通过调节高温裂解系统的温度可以有效调节不同的硒活性.研究发现, 第一台阶HC-Se气氛可以提高CIGS薄膜表面的Ga含量, 使得CIGS薄膜内的Ga分布更加平缓, 进而提高CIGS薄膜表面禁带宽度.而且HC-Se气氛可以消除CIGS"两相分离"现象.两种因素的共同作用使得CIGS薄膜太阳电池的开路电压提高了34.6%.电池转换效率从6.02%提升至8.76%, 增长了45.5%.     

不同环境下硫化镉/铜基薄膜异质结退火对太阳电池性能调控

高效铜基薄膜太阳电池通常采用无机n型半导体材料CdS作为缓冲层,因此,缓冲层与吸收层之间的界面质量和能带匹配对载流子的收集利用至关重要.在优化CdS基础工艺的基础上,在含硫气氛下对硫化镉/铜基薄膜异质结进行退火的策略进一步提高CdS薄膜质量,并将其应用到铜基太阳电池,调控铜基薄膜电池p-n异质结能带匹配.研究表明, CdS薄膜在含硫的惰性气氛中退火可以有效提高CdS薄膜的结晶质量并抑制CZTS/CdS异质结界面的非辐射复合,器件的开路电压得到大幅提升,最高可达718 mV.在器件效率方面,基于溅射法的CZTS太阳电池效率从3.47%提升到5.68%,约为不退火处理的2倍.该研究为铜基薄膜太阳电池器件实现高开路电压提供了可靠的工艺窗口.同时,有力地说明了退火气氛选择对于CdS质量以及CZTS/CdS异质结能带匹配的重要性,除了界面互扩散以外,对薄膜材料组分及其结晶性等均实现了调控.     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃(2 min)下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明:对于不同成分比例的CIGS(正常、富Cu、高Ga)电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证;而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

不同成分比例CIGS薄膜及太阳电池的快速退火

研究了110~180 ℃（2 min）下的快速热退火对Cu(In,Ga)Se2(CIGS)薄膜特性及CIGS太阳电池性能的影响.结果表明：对于不同成分比例的CIGS（正常、富Cu、高Ga）电池来说,150 ℃,2 min的快速退火最利于电池性能及二极管特性的增加.其中,退火对富Cu电池的开路电压Voc改善最大,这是因为快速热退火对消除部分CIGS薄膜中的CuSex有积极作用,从薄膜的电阻率有少量提高,器件的短路电流Jsc有少量下降可以得到验证|而对于高Ga电池来说,填充因子FF的改善最大,这是因为高Ga样品的缺陷较多,退火会消除薄膜内部的部分缺陷,从而薄膜的迁移率及Jsc都有所提高,使得FF有较大的增加.     

预制层溅射气压对CIGS薄膜结构及器件的影响

研究了金属预制层制备过程中溅射气压对Cu(In_1-xGa_x)Se₂(CIGS)薄膜及电池器件性能的影响.通过调节溅射气压改变预制层的结晶状态及疏松度与粗糙度,在合适的预制层结构下,活性硒化热处理过程中,可使Ga有效地掺入到薄膜中形成优质的CIGS固溶体.高溅射气压会使预制层过于致密,呈现非晶态趋势.经活性硒化热处理后,CIGS薄膜容易产生CIS与CGS"两相分离"现象,从而导致CIGS薄膜太阳电池的开路电压和填充因子降低,电池转换效率由10.03%降低到5.02%.     

连续离子层吸附反应沉积后硫化法制备柔性铜锌锡硫薄膜太阳电池

在柔性钼箔衬底上采用连续离子层吸附反应法(successive ionic layer absorption and reaction)制备ZnS/Cu2SnSx叠层结构的预制层薄膜,预制层薄膜在蒸发硫气氛、550 C温度条件下进行退火得到Cu2ZnSnS4吸收层.分别采用EDS,XRD,Raman,SEM表征吸收层薄膜的成分、物相和表面形貌.结果表明,退火后薄膜结晶质量良好,表面形貌致密.用在普通钠钙玻璃上采用相同工艺制备的CZTS薄膜表征薄膜的光学和电学性能,表明退火后薄膜带隙宽度为1.49 eV,在可见光区光吸收系数大于104cm 1,载流子浓度与电阻率均满足薄膜太阳电池器件对吸收层的要求.用上述柔性衬底上的吸收层制备Mo foil/CZTS/CdS/i-ZnO/ZnO:Al/Ag结构的薄膜太阳电池得到2.42%的效率,是目前报道柔性CZTS太阳电池最高效率.     

基于氧化镍背接触缓冲层碲化镉薄膜太阳电池的研究

采用电子束蒸发法制备了NiO薄膜,并对其作为碲化镉薄膜太阳电池背接触缓冲层材料进行了相关研究.NiO缓冲层的加入使得碲化镉太阳电池开路电压显著增大.通过X射线光电子能谱测试得到的NiO/CdTe界面能带图表明NiO和CdTe的能带匹配度很好.NiO是宽禁带P型半导体材料,在电池背接触处形成背场,减少了电子在背表面处的复合,从而提高电池开路电压.通过优化NiO薄膜厚度,制备得到转换效率为12.2%、开路电压为789 mV的碲化镉太阳电池.研究证实NiO是用来制备高转换效率、高稳定性碲化镉薄膜太阳电池的一种极有前景的缓冲层材料.     

氢化纳米硅薄膜中氢的键合特征及其能带结构分析

对氢化纳米硅薄膜中氢的键合特征和薄膜能带结构之间的关系进行了研究.所用样品采用螺 旋波等离子体化学气相沉积技术制备，利用Raman散射、红外吸收和光学吸收技术对薄膜的 微观结构、氢的键合特征以及能带结构特性进行了分析.Raman结果显示不同衬底温度下所生 长薄膜的微观结构存在显著差异，从非晶硅到纳米晶硅转化的衬底温度阈值为200℃.薄膜中 氢的键合特征与薄膜的能带结构密切相关.氢化非晶硅薄膜具有较高的氢含量，因键合氢引 起的价带化学位移和低衬底温度决定的结构无序性，使薄膜呈现较大的光学带隙和带尾宽度 .升 关键词： 氢化纳米硅 螺旋波等离子体 能带结构     

Influence of different precursor surface layers on Cu(In<Subscript>1-x</Subscript>Ga<Subscript>x</Subscript>)Se<Subscript>2</Subscript> thin film solar cells

The properties of Cu(In_1-xGa_x)Se₂ (CIGS) thin films obtained by selenization of the precursors with different surface layers have been studied, and photovoltaic devices based on the absorbers were measured and analyzed. The devices constructed by the absorbers obtained by selenization of the precursors with CuGa-rich surface layers are improved, compared with those with In-rich surface layers. Through XRD, SEM, SIMS, illuminated J–V, QE and Raman spectra measurements, it was found that the increased Ga contents within the surface region of films and the graded Ga distribution can be realized in the selenized thin films fabricated by the precursors with the CuGa-rich surface layer. Consequently, the performances of the photovoltaic devices based on these thin films are further improved. PACS 61.72.Ss; 87.64.Jt; 68.60.Bs; 81.15.Cd; 84.60.Jt     

Improvement in efficiency of solar cell by removing Cu2－xSe from CIGS film surface

CIGS thin films are deposited by sputtering and selenization. The synthesis of semiconducting polycrystalline thin films and characteristics of devices based on the CIGS absorbing layers are investigated. Their microstructures are characterized by x-ray diffraction and Raman spectroscopy. The results reveal that there exist metallic Cu_2-xSe compounds in CIGS film surfaces and the compounds are thought to be responsible for the degradation of the open circuit voltage of solar cells. The optimization of selenization temperature profile and copper content in the precursor surfaces is studied, concluding that the conversion efficiency may be improved by removing metallic Cu_2-xSe compounds from the surfaces of CIGS thin films.     

硒化前后电沉积贫铜和富铜的Cu(In1-xGax)Se2薄膜成分及结构的比较

采用电沉积法获得了接近化学计量比的贫铜和富铜的Cu（In_1-xGa_x）Se₂（CIGS）预置层,研究比较了两种预置层及其硒化处理后的成分和结构特性.得到了明确的实验证据证明,硒化后富铜薄膜中的Cu_xSe相会聚集凝结成结晶颗粒分散在表面.研究表明：在固态源硒化处理后,薄膜成分基本不变;当预置层中原子比Cu/（In+Ga）<11时,硒化后薄膜表面存在大量的裂纹;而当Cu/（In+Ga） >12时,可以消除裂纹的产生,形成等轴状小晶粒;富铜预置层硒化时蒸发沉积少量In,Ga和Se后,电池效率已达到68%;而贫铜预置层硒化后直接制备的电池效率大于2%,值得进一步深入研究. 关键词： 1-xGa_x）Se₂薄膜')" href="#">Cu（In_1-xGa_x）Se₂薄膜 电沉积 硒化处理 贫铜或富铜薄膜     

Preparation of CuInGeSe4 thin films by selenization method using the Cu-In-Ge evaporated layer precursors

CuInGeSe₄ quaternary compounds are known to have a chalcopyrite-like structure and have band gaps of about 1.3 eV, suitable for optimum conversion efficiency for solar cells. We have prepared the CuInGeSe₄ thin films by the selenization method using the Cu-In-Ge evaporated layer precursors. The analyses of X-ray diffraction show that the single phase of CuInGeSe₄ is obtained by the selenization of precursors at 450-500 °C. The SEM observation of film surface shows that the grain sizes are in the order of 1-2 μm. The band gaps of selenized films close to 1.6 eV are wider than that of bulk crystals (about 1.3 eV). These films have p-type conduction and higher electrical resistivities than more 10⁵ Ω cm at room temperature.     

Low-temperature-processed ZnO thin films as electron transporting layer to achieve stable perovskite solar cells

Morphology and surface property of ZnO thin films as electron transporting layer in perovskite solar cells are crucial for obtaining high-efficient and stable perovskite solar cells. In this work, two different preparation methods of ZnO thin films were carried out and the photovoltaic performances of the subsequent perovskite solar cells were investigated. ZnO thin film prepared by sol–gel method was homogenous but provided high series resistance in solar cells, leading to low short circuit current density. Lower series resistance of solar cell was obtained from homogeneous ZnO thin film from spin-coating of colloidal ZnO nanoparticles (synthesized by hydrolysis–condensation) in a mixture of 1-butanol, chloroform and methanol. The perovskite solar cells using this film achieved the highest power conversion efficiency (PCE) of 4.79% when poly(3-hexylthiophene) was used as a hole transporting layer. In addition, the stability of perovskite solar cells was also examined by measuring the photovoltaic characteristic for six consecutive weeks with the interval of 2 weeks. It was found that using double layers of the sol–gel ZnO and ZnO nanoparticles provided better stability with no degradation of PCE in 10 weeks. Therefore, this work provides a simple method for preparing homogeneous ZnO thin films in order to achieve stable perovskite solar cells, also for controlling their surface properties which help better understand the characteristics of perovskite solar cells.     

A non-selenization technology by co-sputtering deposition for solar cell applications

This work presents a novel method to form polycrystalline Cu(In(1-x)Ga(x))Se(2) (CIGS) thin film by co-sputtering of In─Se and Cu─Ga alloy targets without an additional selenization process. An attempt was also made to thoroughly elucidate the surface morphology, crystalline phases, physical properties, and chemical properties of the CIGS films by using material analysis methods. Experimental results indicate that CIGS thin films featured densely packed grains and chalcopyrite phase peaks of (112), (220), (204), (312), and (116). Raman spectroscopy analysis revealed chalcopyrite CIGS phase with Raman shift at 175 cm(-1), while no signal at 258 cm(-1) indicated the exclusion of Cu(2-x)Se phase. Hall effect measurements confirmed the polycrystalline Cu(In,Ga)Se₂ thin film to be of p type semiconductor with a film resistivity and mobility of 2.19×10(2) Ω cm and 88 cm(2)/V s, respectively.     

Two-step growth of VSe_2 films and their photoelectric properties

We put forward a two-step route to synthesize vanadium diselenide(VSe_2), a typical transition metal dichalcogenide(TMD). To obtain the VSe_2 film, we first prepare a vanadium film by electron beam evaporation and we then perform selenization in a vacuum chamber. This method has the advantages of low temperature, is less time-consuming, has a large area, and has a stable performance. At 400?C selenization temperature, we successfully prepare VSe_2 films on both glass and Mo substrates. The prepared VSe_2 has the characteristic of preferential growth along the c-axis, with low transmittance.It is found that the contact between Al and VSe_2/Mo is ohmic contact. Compared to Mo substrate, lower square resistance and higher carrier concentration of the VSe_2/Mo sample reveal that the VSe_2 film may be a potential material for thin film solar cells or other semiconductor devices. The new synthetic strategy that is developed here paves a sustainable way to the application of VSe_2 in photovoltaic devices.     

电沉积Cu-In-Ga金属预制层的硒硫化研究

以H₂S气体作为硫源、固态蒸发硒蒸气作为硒源对电沉积Cu-In-Ga金属预制层进行硒硫化处理. 通过电沉积Cu-In-Ga金属预制层在不同衬底温度下硒化、硫化和硒硫化的对比实验,发现CuInS₂相和CuIn（S,Se）₂相优先生成,抑制了CuInSe₂相的生成,促使InSe相薄膜向内部扩散,减弱了薄膜两相分离现象. 采用先硒化后硒硫化处理工艺优化了Cu（In,Ga）（S,Se）₂薄膜的制备工艺,在250 ℃预硒化得到了开路电压为570 mV的太阳电池,在更高的预硒化温度得到了较大短路电流的太阳电池,最终优化得到了效率达到10.4%的电池器件. 关键词： 电化学沉积 Cu-In-Ga金属预制层 硒硫化处理 2薄膜')" href="#">Cu(In,Ga)(S,Se)₂薄膜     

电沉积Cu(In,Ga)Se_2预置层硫化退火制备Cu(In,Ga)(Se,S)_2薄膜及表征

在550℃下的H2S气氛中退火处理电沉积制备的Cu(In,Ga)Se2(CIGS)预置层,制备了太阳电池光吸收层Cu(In,Ga)(Se,S)2(CIGSS)薄膜.采用X射线能量色散谱、俄歇电子能谱、扫描电镜、X射线衍射和拉曼光谱对退火前后的薄膜进行表征.结果表明,H2S气氛下退火能够实现薄膜中O的去除和S的掺入,同时使得各元素的纵向分布更加均匀并可消除Cu-Se微相.此外,H2S退火还可改善薄膜的结晶性能,并使S和Ga进入黄铜矿结构,薄膜晶格参数变小.     

Inkjet printed Cu(In,Ga)S<Subscript>2</Subscript> nanoparticles for low-cost solar cells

Cu(In,Ga)Se₂ (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S₂ (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.