A novel dual-material probe for in situ measurement of particle charge densities in gas–solid fluidized beds

Particle charge density is vitally important for monitoring electrostatic charges and understanding particle charging behavior in fluidized beds. In this paper, a dual-material probe was tested in a gas–solid fluidized bed for measuring the charge density of fluidized particles. The experiments were conducted in a two-dimensional fluidized bed with both single bubble injection and freely bubbling, at various particle charge densities and superficial gas velocities. Uniformly sized glass beads were used to eliminate complicating factors at this early stage of probe development. Peak currents, extracted from dynamic signals, were decoupled to determine charge densities of bed particles, which were found to be qualitatively and quantitatively consistent with charge densities directly measured by Faraday cup from the freely bubbling fluidized bed. The current signals were also decoupled to estimate bubble rise velocities, which were found to be in reasonable agreement with those obtained directly by analyzing video images.     

Fluidization and bubbling behavior of potash particles in a deep fluidized bed

Most existing models for predicting bubble size and bubble frequency have been developed for freely bubbling fluidized beds. Accurate prediction of bubbling behavior in deep fluidized beds, however, has been a challenge due to the higher degree of bubble coalescence and break up, high probability of the slugging regime, partial fluidization, and chaotic behavior in the bubbling regime. In this work, the bubbling and fluidization behavior of potash particles was investigated in a deep fluidized bed employing a twin-plane electrical capacitance tomography (ECT) system. Solid volume fraction, average bubble velocity, average bubble diameter, and bubble frequency in both bubbling and slugging regimes were measured at two different bed height ratios (H/D = 3.5 and H/D = 3.78). This work is the first to illustrate a sequential view of bubbles at different superficial gas velocities in a fluidized bed. The results show that both the bubble diameter and rising velocity increased with increasing the superficial gas velocity for the two bed heights, with larger values observed in the deeper bed compared to the shallower one. Predicted values for bubble diameter, bubble rise velocity and bubble frequency from different models are compared with the experimental data obtained from the ECT system in this work. Good agreement has been achieved between the values predicted by the previous models and the experimental data for the bubble diameter and bubble rise velocity with an average absolute deviation of 16% and 15% for the bed height of 49 cm and 13% and 8% for the bed height of 53 cm, respectively.     

Influence of vertical internals on a bubbling fluidized bed characterized by X-ray tomography

An ultra-fast X-ray tomographic scanner is applied to study the hydrodynamics in a bubbling fluidized bed with and without vertical internals (e.g., heat exchanger tubes). The objective of this study is to understand the influence of vertical internals on hydrodynamic properties such as bubble volume, size and velocity and to provide measurement data for the design and scale-up of catalytic bubbling fluidized bed reactors with vertical internals. With these new measurements, correlations of bubble properties can be developed to reliably scale-up bubbling fluidized beds with vertical internals. For the investigated reactor with Geldart A/B particles, no relation between bubble size and velocity was observed for individual bubbles, i.e.; smaller bubbles tend to rise with higher velocities. A significant reduction in bubble size and sharpening of the bubble size distribution was generally obtained for a bed with vertical internals.     

The measurement of bubble flows in fluidized beds by electrical probe

Measurements of bubble velocities, dimensions and flow rates in a two-dimensional fluidized bed by a dual electrical capacitive probe are compared with measurements from cine photography; the cine photographs and electric measurements were taken at the same point in a fluidized bed and at the same time. It was found that both sets of measurements were in agreement only when the conditions of electrical measurement were arranged to exclude spurious signals, while still retaining sensitivity, and when the theory of measurement included the effects of bubble retardation and distortion, and allowed for the stochastic incidence between the bubble front and the probes.     

BUBBLE CHARACTERISTICS IN A TWO-DIMENSIONAL VERTICALLY VIBRO-FLUIDIZED BED

Measurement of bubble size and local average bubble rise velocity was carried out in a vertically sinusoidal vibro-fluidized bed. Glass beads of Geldart group B particles were fluidized at different gas velocities, while the bed was vibrated at different frequencies and amplitudes to study their effects on the bubble behavior. This is compared with the case of no vibration in a two-dimensional bed and it is concluded that with vibration the local average bubble size, dbav, decreases significantly, especially at minimum bubbling velocity. The average bubble size increases slightly with increasing vibration frequency and amplitude. The local average bubble rise velocity is higher than that with no vibration, though with increasing vibration frequency and amplitude, it does not change significantly.     

ELECTROSTATIC PHENOMENA IN GAS-SOLIDS FLUIDIZED BEDS

Electrostatic charges are generated by particle-wall, particle-particle and particle-gas contacts in gas-solids transport lines and fluidized bed reactors. High particle charge densities can lead to particle agglomeration, particle segregation, fouling of reactor walls and internals, leading to undesirable by-product and premature shut-down of processing equipment. In this paper, the charge generation, dissipation and segregation mechanisms are examined based on literature data and recent experimental findings in our laboratory. The particle-wall contact charging is found to be the dominant charge generation mechanism for gas-solids pneumatic transport lines, while bipolar charging due to intimate particle-particle contact is believed to be the dominant charge generation mechanism in gas fluidized beds. Such a bipolar charging mechanism is also supported by the segregation patterns of charged particles in fluidized beds in which highly charged particles tend to concentrate in the bubble wake and drift region behind rising bubbles.     

Bottom bed regimes in a circulating fluidized bed boiler

This paper extends previous work on the fluidization regimes of the bottom bed of circulating flyidized bed (CFB) boilers. Pressure measurements were performed to obtain the time-average bottom bed voidage and to study the bed pressure fluctuations. The measurements were carried out in a 12 MW_th CFB boiler operated at 850°C and also under ambient conditions (40°C). Two bubbling regimes were identified: a “single bubble regime” with large single bubbles present at low fluidization velocities, and, at high fluidization velocities, an “exploding bubble regime” with bubbles often stretching all the way from the air distributor to the surface of the bottom bed. The exploding bubble regime results in a high through-flow of gas, indirectly seen from the low average voidage of the bottom bed, which is similar to that of a stationary fluidized bed boiler, despite the higher gas velocities in the CFB boiler. Methods to determine the fluidization velocity at the transition from the single to the exploding bubble regime are proposed and discussed. The transition velocity increases with an increase in particle size and bed height.     

Characterization of gas–solid fluidized bed hydrodynamics by vibration signature analysis

Vibration measurement, as a non-intrusive technique, was used to characterize the hydrodynamics of fluidized beds. A series of experiments were performed in a lab-scale fluidized bed using two accelerometers for measuring the vibration of the bed and a pressure probe for measuring pressure fluctuations. The output signals were analyzed by statistical methods. The results show that the vibration technique can predict transition velocities at high velocities and indicate that analyzing the vibration signals can be an effective non-intrusive technique to characterize the hydrodynamics of fluidized beds. It was shown that transition from bubbling to turbulent velocity can be determined from the variation of standard deviation and kurtosis of vibration signals against superficial gas velocity of the bed. However, this point could be determined only from standard deviation of pressure fluctuations, and not from skewness or kurtosis of pressure fluctuations.     

Vibration time series analysis of bubbling and turbulent fluidization

A non-intrusive vibration monitoring technique was used to study the hydrodynamics of a gas–solid fluidized bed. Experiments were carried out in a 15 cm diameter fluidized bed using 226, 470 and 700 μm sand particles at various gas velocities, covering both bubbling and turbulent regimes. Auto correlation function, mutual information function, Hurst exponent analysis and power spectral density function were used to analyze the fluidized bed hydrodynamics near the transition point from bubbling to turbulent fluidization regimes. The first pass of the autocorrelation function from one half and the time delay at which it becomes zero, and also the first minimum of the mutual information, occur at a higher time delay in comparison to stochastic systems, and the values of time delays were maximum at the bubbling to turbulent transition gas velocity. The maximum value of Hurst exponent of macro structure occurred at the onset of regime transition from bubbling to turbulent. Further increase in gas velocity after that regime transition velocity causes a decrease in the Hurst exponent of macro structure because of breakage of large bubbles to small ones. The results showed these methods are capable of detecting the regime transition from bubbling to turbulent fluidization conditions using vibration signals.     

Effect of promoters on dynamics of gas-solid fluidized bed Statistical and ANN approaches

In this study, a bubbling fluidized bed column, 99 mm in inside diameter and 960 mm in height, was used to investigate the effect of rod and disc promoters on fluctuation and expansion ratios. Factorial design （statistical approach） and artificial neural network （ANN） models were developed to predict the fluctuation and expansion ratios in this gas-solid fluidized bed with varying gas flow rates, bed heights, particle sizes and densities. The fluctuation and expansion predicted using these statistical and ANN models, for beds with and without promoters, were found to agree well with corresponding experiments. The statistical model was found to be superior to the ANN model due to its ability to take into account both individual and interactive effects. The rod promoters were found to be more effective in reducing bed fluctuation, and in increasing bed expansion at high gas mass velocities.     

Discrete particle modeling of granular temperature distribution in a bubbling fluidized bed

The discrete hard sphere particle model (DPM) is applied in this work to study numerically the distributions of particle and bubble granular temperatures in a bubbling fluidized bed. The dimensions of the bed and other parameters are set to correspond to those of Müller et al. (2008). Various drag models and operational parameters are investigated to find their influence on particle and bubble granular temperatures. Various inlet superficial gas velocities are used in this work to obtain their effect on flow characteristics. It is found that the superficial gas velocity has the most important effect on granular temperatures including bubble granular temperature, particle translational granular temperature and particle rotational granular temperature. The drag force model affects more seriously the large scale variables such as the bubble granular temperature. Restitution coefficient influences all granular temperatures to some degree. Simulation results are compared with experimental results by Müller et al. (2008) showing reasonable agreement.     

CFD–DEM study of effect of bed thickness for bubbling fluidized beds

The effect of bed thickness in rectangular fluidized beds is investigated through the CFD–DEM simulations of small-scale systems. Numerical results are compared for bubbling fluidized beds of various bed thicknesses with respect to particle packing, bed expansion, bubble behavior, solids velocities, and particle kinetic energy. Good two-dimensional (2D) flow behavior is observed in the bed having a thickness of up to 20 particle diameters. However, a strong three-dimensional (3D) flow behavior is observed in beds with a thickness of 40 particle diameters, indicating the transition from 2D flow to 3D flow within the range of 20–40 particle diameters. Comparison of velocity profiles near the walls and at the center of the bed shows significant impact of the front and back walls on the flow hydrodynamics of pseudo-2D fluidized beds. Hence, for quantitative comparison with experiments in pseudo-2D columns, the effect of walls has to be accounted for in numerical simulations.     

Bubbling behavior of cohesive particles in a two-dimensional fluidized bed with immersed tubes

Fluidization hydrodynamics are greatly influenced by inter-particle cohesive forces. This paper studies the fluidization of large cohesive particles in a two-dimensional fluidized bed with immersed tubes using “polymer coating” to introduce cohesive force, to gain better understanding of bubbling behavior when particles become cohesive and its effect on chemical processes. The results show that the cohesive force promotes bubble splitting in the tube bank region, thereby causing an increase in the number and a decline in the aspect ratio of the bubbles. As the cohesive force increases within a low level, the bubble number increases and the bubble diameter decreases, while the aspect ratio exhibits different trends at different fluidization gas velocities. The difference in the evolution of bubble size under various cohesive forces mainly takes place in the region without tubes. When the cohesive force is large enough to generate stable agglomerates on the side walls of the bed, the bubble number and the bed expansion sharply decrease. The tubes serve as a framework that promotes the agglomeration, thus accelerating defluidization. Finally, the bubble profile around tubes was studied and found to greatly depend both on the cohesive forces and the location of tubes.     

DEM simulation of polydisperse systems of particles in a fluidized bed

Numerical simulations based on three-dimensional discrete element model (DEM) are conducted for mono-disperse, binary and ternary systems of particles in a fluidized bed. Fluid drag force acting on each particle depending on its size and relative velocity is assigned. The drag coefficient corresponding to Ergun’s correlation is applied to the system of fluidized bed with particle size ratios of 1:1 for the mono-disperse system, 1:1.2, 1:1.4 and 1:2 for the binary system and 1:1.33:2 for the ternary system b...     

A new drag model for TFM simulation of gas–solid bubbling fluidized beds with Geldart-B particles

In this work, a new drag model for TFM simulation in gas–solid bubbling fluidized beds was proposed, and a set of equations was derived to determine the meso-scale structural parameters to calculate the drag characteristics of Geldart-B particles under low gas velocities. In the new model, the meso-scale structure was characterized while accounting for the bubble and meso-scale structure effects on the drag coefficient. The Fluent software, incorporating the new drag model, was used to simulate the fluidization behavior. Experiments were performed in a Plexiglas cylindrical fluidized bed consisting of quartz sand as the solid phase and ambient air as the gas phase. Comparisons based on the solids hold-up inside the fluidized bed at different superficial gas velocities, were made between the 2D Cartesian simulations, and the experimental data, showing that the results of the new drag model reached much better agreement with experimental data than those of the Gidaspow drag model did.     

A new drag model for TFM simulation of gas-solid bubbling fluidized beds with Geldart-B particles

In this work, a new drag model for TFM simulation in gas-solid bubbling fluidized beds was proposed, and a set of equations was derived to determine the meso-scale structural parameters to calculate the drag characteristics of Geldart-B particles under low gas velocities. In the new model, the meso-scale structure was characterized while accounting for the bubble and meso-scale structure effects on the drag coefficient. The Fluent software, incorporating the new drag model, was used to simulate the fluidization behavior. Experiments were performed in a Plexiglas cylindrical fluidized bed consisting of quartz sand as the solid phase and ambient air as the gas phase. Comparisons based on the solids hold-up inside the fluidized bed at different superficial gas velocities, were made between the 2D Cartesian simulations, and the experimental data, showing that the results of the new drag model reached much better agreement with exoerimental data than those of the Gidasoow dra~ model did.     

Particle Measurement Sensor for in situ determination of phase structure of fluidized bed

Based on three-dimensional (3D) acceleration sensing, an intelligent particle spy capable of detecting, transferring, and storing data, is proposed under the name of Particle Measurement Sensor (PMS). A prototype 60-mm-dia PMS was tested to track its freefall in terms of velocity and displacement, and served as a particle spy in a fluidized bed delivering the in situ acceleration information it detects. With increasing superficial gas velocity in the fluidized bed, the acceleration felt by PMS was observed to increase. The variance of the signals, which reflect the fluctuation, increased at first, reaching a maximum at the gas velocity (Uc) which marks the transition from bubbling to turbulent fluidization. Through probability density distribution (PDD) analysis, the PDD peak can be divided into the emulsion phase peak and the bubble phase peak. The average acceleration of emulsion and bubble phase increased, while the variance of both phases reached a maximum at Oc, at the same time. However, the difference between the variances of two phases reached the maximum at Oc. Findings of this study indicate that PMS can record independent in situ information. Further, it can provide other in situ measurements when equipped with additional multi-functional sensors.     

Bubble dynamics in a two-dimensional gas-solid fluidized bed

Related referential studies on gas-solid two-phase flows were briefly reviewed. Bubble ascending in a two-dimensional （2D） gas-solid fluidized bed was studied both experimentally and numerically. A modified continuum model expressed in the conservation form was used in numerical simulation. Solid-phase pressure was modeled via local sound speed; gas-phase turbulence was described by the K-ε two-equation model. The modified implicit multiphase formulation （IMF） scheme was used to solve the model equations in 2D Cartesian/cylindrical coordinates. The bubble ascending velocity and particle motion in the 2D fluidized bed were measured using the photochromic dye activation （PDA） technique, which was based on UV light activation of particles impregnated with the dye. Effects of bed height and superficial gas velocity on bubble formation and ascent were investigated numerically. The numerically obtained bubble ascending velocities were compared with experimental measurements. Gas bubble in jetting gas-solids fluidized bed was also simulated numerically.     

Flow structure and bubble dynamics in supercritical water fluidized bed and gas fluidized bed: A comparative study

Supercritical water (SCW) fluidized bed is a new reactor concept for hydrogen production from biomass or coal gasification. In this paper, a comparative study on flow structure and bubble dynamics in a supercritical water fluidized bed and a gas fluidized bed was carried out using the discrete element method (DEM). The results show that supercritical water condition reduces the incipient fluidization velocity, changes regime transitions, i.e. a homogeneous fluidization was observed when the superficial velocity is in the range of the minimum fluidization velocity and minimum bubbling velocity even the solids behave as Geldart B powders in the gas fluidized bed. Bubbling fluidization in the supercritical water fluidized bed was formed after superficial velocity exceeds the minimum bubbling velocity, as in the gas fluidized bed. Bubble is one of the most important features in fluidized bed, which is also the emphasis in this paper. Bubble growth was effectively suppressed in the supercritical water fluidized bed, which resulted in a more uniform flow structure. By analyzing a large number of bubbles, bubble dynamic characteristics such as diameter distribution, frequency, rising path and so on, were obtained. It is found that bubble dynamic characteristics in the supercritical water fluidized bed differ a lot from that in the gas fluidized bed, and there is a better fluidization quality induced by the bubble dynamics in the supercritical water fluidized bed.     

鼓泡流化床中流动特性的多尺度数值模拟

鼓泡流化床因其较高的传热特性以及较好的相间接触已经被广泛应用于工业生产中,而对鼓泡流态化气固流动特性的充分认知是鼓泡流化床设计的关键.在鼓泡流化床中,气泡相和乳化相的同时存在使得床中呈现非均匀流动结构,而这种非均匀结构给鼓泡流化床的数值模拟造成了很大的误差.基于此,以气泡作为介尺度结构,建立了多尺度曳力消耗能量最小的稳定性条件,构建了适用于鼓泡流化床的多尺度气固相间曳力模型.结合双流体模型,对A类和B类颗粒的鼓泡流化床中气固流动特性进行了模拟研究,分析了气泡速度、气泡直径等参数的变化规律.研究表明,与传统的曳力模型相比,考虑气泡影响的多尺度气固相间曳力模型给出的曳力系数与颗粒浓度的关系是一条分布带,建立了控制体内曳力系数与局部结构参数之间的关系.通过模拟得到的颗粒浓度和速度与实验的比较可以发现,考虑气泡影响的多尺度曳力模型可以更好地再现实验结果.通过A类和B类颗粒的鼓泡床模拟研究发现,A类颗粒的鼓泡床模拟受多尺度曳力模型的影响更为显著.