聚(异氰脲酸酯-噁唑烷酮)合成反应的研究

本文对聚(异氰脲酸酯-噁唑烷酮)(PISOX)的合成反应进行了系统研究.用原位红外法定量地研究了温度、投料比对PISOX合成中噁唑烷酮(OX)和异氰脲酸酯(IS)成环反应的影响规律.结果发现,低温有利于IS的生成,高温有利OX的生成;在高温下IS转化为OX;投料比与固化工艺决定着PISOX的结构.     

多官能度噁唑烷的合成及其改性聚氨酯材料

合成了2,2-二甲基-N-羟乙基-1,3-噁唑烷(OX),并以其为结构单元合成了2种多官能度的噁唑烷化合物——丙二酸二-2,2-二甲基-N-羟乙基-1,3-噁唑烷酯(OX1)和1,1,5,5-戊烷端四甲酸四-2,2-二甲基-N-羟乙基-1,3-噁唑烷酯(OX2).采用13C核磁共振谱、质谱、元素分析和傅里叶变换红外光谱对产物结构进行表征,并探索了产物用于单组份湿固化聚氨酯(SPU)体系的潜固化剂性能.研究了固化体系的表观性能、力学性能和热性能.结果表明:纯湿固化SPU发泡且膨胀,拉伸强度为3.2 MPa,断裂伸长率为364%;而SPU-OX2固化体系的拉伸强度达27.2 MPa,是纯SPU固化体系拉伸强度(3.2 MPa)的9倍;SPU-OX2固化体系断裂伸长率达457%,是纯SPU固化体系断裂伸长率(364%)的1.26倍.聚氨酯中加入噁唑烷OX1和OX2为潜固化剂,不仅较好改善了聚氨酯的表观性能,而且增加了聚氨酯预聚体的力学性能和热稳定性.     

一种有效合成3-芳基-4-氟烷基-2-噁唑烷酮的方法

报道了一种方便有效地合成3-芳基-4-氟烷基-2-噁唑烷酮的方法.用芳基胺作为起始原料通过与氯甲酸烯丙基酯反应以95.8%～99.5%的收率得到芳基氨基甲酸烯丙基酯.芳基氨基甲酸烯丙基酯与氟烷基碘在乙腈和水的混合液中由连二亚硫酸钠引发在室温下发生自由基加成反应得到氟烷基化的加成产物.加成产物在碱性条件下发生分子内的N-环合反应得到3-芳基-4-氟烷基-2-噁唑烷酮.整个反应都在室温下进行,并且没有用到光气合成了3-芳基-4-氟烷基-2-噁唑烷酮,该方法具有原料易得,条件温和,绿色环保的优点.     

1,8-二氮杂二环十一碳-7-烯(DBU)立体选择性催化合成噁唑啉-2-(硫)酮衍生物

以1,8-二氮杂二环十一碳-7-烯(DBU)为催化剂,在无其它金属催化条件下,炔丙醇与异氰酸酯(或硫氰酸酯)进行亲核加成/环化反应,合成了一系列多取代的噁唑烷-2-(硫)酮衍生物,收率为75%~95%.该反应经5-exo-dig环化机制,高度立体选择性地得到Z-式芳亚甲基取代产物,为噁唑啉酮的骨架合成提供了简单快速的合成方法.     

5-(3′-芳基-5′-噁唑烷酮基甲氧基)-3(2H)哒嗪酮类化合物的合成及生物活性

5-(3′-芳基-5′-噁唑烷酮基甲氧基)-3(2H)哒嗪酮类化合物的合成及生物活性;芳基噁唑烷酮基甲氧基哒嗪酮;合成;生物活性     

手性5-异丙基-2-噁唑烷酮的酶催化立体选择性互补合成

以2-异丙基环氧乙烷为底物,氰酸钠为亲核试剂,筛选获得两种卤醇脱卤酶HheA10和HheG,可以分别催化合成(S)-5-异丙基-2-噁唑烷酮和(R)-5-异丙基-2-噁唑烷酮。通过对其反应条件进一步考察,建立了立体选择性互补合成手性5-异丙基-2-噁唑烷酮的生物催化技术路线。      

噁唑烷酮环氧树脂的研究进展

含噁唑烷酮结构的树脂具有优良的耐热性、电性能及物理机械性能等。将噁唑烷酮环引入环氧树脂,可提高固化物的玻璃化转变温度、粘结性、介电性和阻燃性等。本文综述了噁唑烷酮环氧树脂的一般合成方法,探讨了原料配比、反应温度、催化剂种类及用量对噁唑烷酮环氧树脂合成过程的影响,分析了固化剂与噁唑烷酮环氧树脂固化产物性能之间的联系,对噁唑烷酮环氧树脂在绝缘材料、涂料、粘合剂、印刷电路板以及高性能树脂基体等领域的应用情况进行了详细介绍,并对其发展前景予以展望。     

3-丙烯酰基-1,3-噁唑烷-2-酮的合成

3-α,β-不饱和酰基-1,3-噁唑烷-2-酮在烷基化及Diels-Alder等反应中在手性催化剂的存在下,产物都有较高的对映选择性。但3-丙烯酰基-3,3-噁唑烷-2-酮极易聚合,现有制备方法结果均不理想。本文将丙烯酸与丙烯酰氯在三乙胺的存在下生成酸酐,再在无水氯化锂的作用下与1,3-噁唑烷-2-酮在室温反应,反应结束后直接将反应混合物通过硅胶柱色谱进行层析分离得到3-丙烯酰基-1,3-噁唑烷-2-酮,产率达83％。合成路线如下：     

5-芳氧甲基-2-噁唑烷酮的合成及表征

环氧氯丙烷;氯甲基噁唑烷酮;合成;芳氧甲基噁唑烷酮     

(－)-7(R)-羟罗汉脂素的全合成研究

以4-戊烯酸及(R)-4-苯基-2-噁唑烷酮为起始原料, 以氯化镁在三乙胺和三甲基氯化硅存在下催化的(R)-4-苯基-3-戊烯酰基-2-噁唑烷酮的埃文斯（Evans)反式羟醛缩合反应为关键步骤, 经9步反应合成了(－)-7(R)-羟罗汉脂素, 其光谱数据与文献报道的天然产物一致.     

酚醛型氰酸酯与双酚A型环氧共固化反应的FTIR研究

在恒温固化条件下,通过FTIR跟踪方法,研究了酚醛型氰酸酯与双酚A型环氧共固化反应的路径及其反应机理.共固化体系的反应过程包括在150℃及其以下温度,主要发生的是氰酸酯的三嗪环化固化反应,其中三嗪环化固化反应由于环氧的加入,反应速率被极大地提高了;同时,酚醛型氰酸酯中的氨基甲酸酯类杂质与环氧发生开环聚合反应,引起环氧官能团产生弱而持续的消耗.但在此阶段,酚醛型氰酸酯与环氧之间没有化学反应发生;在180℃及其以上温度,三嗪环和环氧发生反应,异构为异氰脲酸环结构,并进一步反应生成唑啉酮环结构,由于该反应的发生,促进了环氧官能团的消耗速度,在环氧官能团的转化率-时间图中,出现倒S曲线;在三嗪环的转化率图中,出现一个极大值后再降落的曲线.反应温度的提高有利于促进酚醛型氰酸酯与环氧之间的共固化反应,特别是当反应温度为220℃时,氰酸酯官能团和环氧官能团的消耗、三嗪环和唑啉酮环的生成均以较快的速率进行,—OCN生成三嗪环的转化率可以较容易地达到1,而唑啉酮环的转化率不超过0.5.     

Biosynthesis of the Polycyclic System in the Antifungal HSAF and Analogues from Lysobacter enzymogenes

The biocontrol agent Lysobacter enzymogenes produces polycyclic tetramate macrolactams (PoTeMs), including the antifungal HSAF. To elucidate the biosynthesis of the cyclic systems, we identified eleven HSAF precursors/analogues with zero, one, two, or three rings through heterologous expression of the HSAF gene cluster. A series of combinatorial gene expression and deletion experiments showed that OX3 is the “gatekeeper” responsible for the formation of the first 5‐membered ring from lysobacterene A, OX1 and OX2 are responsible for formation of the second ring but with different selectivity, and OX4 is responsible for formation of the 6‐membered ring. In vitro experiments showed that OX4 is an NADPH‐dependent enzyme that catalyzes the reductive cyclization of 3‐dehydroxy alteramide C to form 3‐dehydroxy HSAF. Thus, the multiplicity of OX genes is the basis for the structural diversity of the HSAF family, which is the only characterized PoTeM cluster that involves four redox enzymes in the formation of the cyclic system.     

Modification of epoxy resin using reactive liquid (ATBN) rubber

Epoxy resins are widely utilised as high performance thermosetting resins for many industrial applications but unfortunately some are characterised by a relatively low toughness. In this respect, many efforts have been made to improve the toughness of cured epoxy resins by the introduction of rigid particles, reactive rubbers, interpenetrating polymer networks and engineering thermoplastics within the matrix.In the present work liquid amine-terminated butadiene acrylonitrile (ATBN) copolymers containing 16% acrylonitrile is added at different contents to improve the toughness of diglycidyl ether of bisphenol A epoxy resin using polyaminoimidazoline as a curing agent. The chemical reactions suspected to take place during the modification of the epoxy resin were monitored and evidenced using a Fourier transform infrared. The glass transition temperature (T_g) was measured using a differential scanning calorimeter. The mechanical behaviour of the modified epoxy resin was evaluated in terms of Izod impact strength (IS), critical stress intensity factor, and tensile properties at different modifier contents. A scanning electron microscope (SEM) was used to elucidate the mechanisms of deformation and toughening in addition to other morphological features. Finally, the adhesive properties of the modified epoxy resin were measured in terms of tensile shear strength (TSS).When modifying epoxy resin with liquid rubber (ATBN), all reactivity characteristics (gel time and temperature, cure time and exotherm peak) decreased. The infrared analysis evidenced the occurrence of a chemical reaction between the two components. Addition of ATBN led to a decrease in either the glass transition temperature and stress at break accompanied with an increase in elongation at break and the appearance of some yielding. As expected, the tensile modulus decreased slightly from 1.85 to about 1.34 GPa with increasing ATBN content; whereas a 3-fold increase in Izod IS was obtained by just adding 12.5 phr ATBN compared to the unfilled resin. It is obvious that upon addition of ATBN, the Izod IS increased drastically from 0.85 to 2.86 kJ/m² and from 4.19 to 14.26 kJ/m² for notched and unnotched specimens respectively while K_IC varies from 0.91 to 1.49 MPa m^1/2 (1.5-fold increase). Concerning the adhesive properties, the TSS increased from 9.14 to 15.96 MPa just by adding 5 phr ATBN. Finally SEM analysis results suggest rubber particles cavitation and localised plastic shear yielding induced by the presence of the dispersed rubber particles within the epoxy matrix as the prevailing toughening mechanism.     

乙二醇二缩水甘油醚的合成及作为阳离子型紫外光固化稀释剂性能研究

以三氟化硼乙醚络合物为催化剂,以氢氧化钠为成环反应的闭环剂,利用乙二醇和环氧氯丙烷为原料合成了乙二醇二缩水甘油醚.研究了催化剂三氟化硼乙醚络合物用量、环氧氯丙烷和乙二醇摩尔比、氢氧化钠和乙二醇摩尔比,以及成环反应温度这些因素对合成反应的影响.结果表明较好的合成反应条件是:三氟化硼乙醚络合物质量分数为0.40%,环氧氯丙烷和乙二醇较佳摩尔比为2.4:1,氢氧化钠和乙二醇较佳摩尔比为2.2:1,较佳的成环反应温度为30℃.同时,把乙二醇二缩水甘油醚作为稀释剂加入到环氧树脂E-51中,利用三芳基锍鎓六氟锑酸盐作为引发剂,制备了阳离子型紫外光固化涂料,其紫外光固化膜的拉伸强度为46.25MPa,杨氏模量为1487.26MPa,断裂伸长率为6.27%.     

Photo‐/Baso‐Chromisms and the Application of a Dual‐Addressable Molecular Switch

Two typical molecular switches of spiropyran (SP) and benzoxazine (OX) were fused by sharing an indole to achieve a new dual‐addressable molecular switch (SP‐OX‐NO₂). Through proper molecular modification with NO₂, the transformation from merocyanine (MC) to ring‐closed SP or ring‐closed OX can be controlled separately with visible light or base stimuli in solution, respectively, and these processes are verified by UV‐vis and NMR spectroscopy as well as control experiments. The cis‐merocyanine (cis‐MC) form is involved in the basochromic process in solution. DFT calculation suggests that the bidirectional switching property of the fused SP‐OX molecular switch can be controlled separately, when the OX isomer is more stable than the deprotonated SP isomer. Because of the significant color variations in solution, the simple dual‐addressable switch has been further successfully applied to construct a multicolor reversible display on paper.     

含环氧基团的聚合物微球固载2,2,6,6-四甲基哌啶氮氧自由基催化剂的制备及其催化分子氧氧化苯甲醇

以甲基丙烯酸缩水甘油酯(GMA)为单体, 以乙二醇二甲基丙烯酸酯(EGDMA)为交联剂, 采用悬浮聚合法制得交联聚甲基丙烯酸缩水甘油酯(CPGMA)微球, 然后以4-羟基-2,2,6,6-四甲基哌啶氮氧自由基(4-OH-TEMPO)为试剂, 使CPGMA微球表面的环氧基团发生开环反应, 从而制得了TEMPO固载化微球TEMPO/CPGMA, 考察了制备条件对固载化反应的影响, 并采用多种方法对微球TEMPO/CPGMA进行了表征. 将微球TEMPO/CPGMA与CuCl组成共催化体系, 用于分子氧氧化苯甲醇, 考察了反应条件对催化体系性能的影响. 结果表明, 以含环氧基团的聚合物微球CPGMA为载体, 通过开环反应, 可成功地实现TEMPO的固载化, 开环反应属S_N2亲核取代反应, 适宜采用溶剂N,N''-二甲基甲酰胺和反应温度85℃. 非均相催化剂TEMPO/CPGMA与助催化剂CuCl构成共催化体系, 在室温、常压O₂条件下可高效地将苯甲醇氧化为苯甲醛, 产物选择性和产率分别为100%和90%. 主催化剂TEMPO与助催化剂CuCl适宜的摩尔比为1:1.2; 主催化剂适宜用量为0.90 g. 此外, TEMPO/CPGMA固体催化剂具有良好的循环使用性能.     

Mechanism of the tertiary amine-catalyzed dicyandiamide cure of epoxy resins

Infrared and NMR data on tertiary amine-catalyzed, dicyandiamide—epoxy resin (and model compound) systems have been utilized to elucidate the mechanism of the curing process. The early exothermic curing reaction is shown to be ring opening of the resin epoxy groups by dicyandiamide imino and amino anionic species, giving rise to N-alkyl cyanoguanidines; a minor amount of polyether formation also occurs at this time. After the exothermic reaction is essentially complete at <90°C., a slow, high temperature (110–200°C.) addition of hydroxyl hydrogen across the nitrile triple bond occurs, giving rise to an imino ether which then rearranges to the guanyl urea.     

环氧树脂与氰酸酯共固化反应的研究

应用DSC、FT IR对乙酰丙酮过渡金属络合物催化促进的环氧树酯与氰酸酯共固化反应行为、历程以及固化物的结构特征进行了研究探讨 .结果表明 ,促进剂能够明显的降低固化反应温度 ,缩短固化反应时间 .反应历程首先是氰酸酯发生自聚反应形成二聚体或三聚体 (三嗪环 ) ,然后二聚体可进一步共聚形成三嗪环 ,此过程伴随着环氧基的聚醚反应 ,最后是三嗪环与剩余的环氧基反应形成唑烷酮 .在氰酸酯欠量的条件下 ,固化树脂中主要是唑烷酮和聚醚结构 ,三嗪环结构很少 ;在氰酸脂适量或过量条件下 ,固化树脂主要是三嗪环和唑烷酮结构 ,聚醚结构很少 .     

Planar chirality: cycloaddition and transannular reactions of optically active azoninones that contain (E)-olefins

Unsaturated nine-membered ring lactams that contain (E)-olefins within the ring are characterized by planar chiral properties. Thus, selective conversions of the double bond allowed a complete transfer of the planar chiral information into new stereogenic centers The basis of the transformations was the high activation barrier that prevented efficient flipping of the double bond at room temperature (epimerization pR <=> pS) with respect to the ring. Cycloadditions led diastereoselectively to cyclopropano, epimino, epoxy, and dihydroxy azonanones under mild conditions with moderately high yields. The epoxy azonanones were subjected to regio- and diastereoselective transannular epoxide opening/ring contraction sequences to give hydroxy indolizidinones. The regiochemical and stereochemical outcome strongly depends on the configuration of the oxirane and the chiral information of the lactam unit. The so-formed optically active bicycles with defined substitution patterns should serve as versatile building blocks in alkaloid synthesis.