透明光学树脂中Eu3+辐射参数的理论和实验研究

报道了一种新合成的含三元稀土配合物的透明光学树脂材料的辐射特性的研究。基于J-O参数理论,利用含稀土配合物Eu(TTA)3phen-0.31wt%的光学树脂的发射荧光光谱,计算了Eu3 在光学树脂基质中的J-O参数Ω2=10.139 4×10-20cm2,Ω4=3.810 9×10-20cm2,Ω6=9.050 7×10-20cm2。利用得到的J-O参数可以计算光学树脂中Eu3 的跃迁振子强度fcal,5D0激发态的辐射跃迁概率A(456.6 s-1)、辐射寿命τ(2 190.1μs),还计算了光学树脂中Eu3 的跃迁5D0→7FJ′(其中J′=1,2,4,6)的发射截面σ、荧光分支比β。通过分析计算得到的J-O参数可知,光学树脂中Eu3 的5D0亚稳态的寿命较长,跃迁5D0→7F2的发射截面最大,说明含稀土配合物的光学树脂具有作光放大或激光材料的潜在性。     

Eu(TTFA)3掺杂环氧基光刻胶薄膜的强烈红色荧光

合成了稀土配合物Eu(TTFA)3(TTFA, 2-thenoyltrifluoroacetone)掺杂的环氧基紫外负性光刻胶薄膜,采用荧光分光光度计对其光致发光特性进行了系统表征.荧光光谱分析表明,Eu(TTFA)3掺杂的光刻胶薄膜具有很宽的激发谱带(200～400 nm),且在长波紫外区表现为强激发,说明有机配体TTFA-与中心离子之间存在着比电荷迁移带更有效的能量传递.配体TTFA-的三重激发态和Eu3+的激发态能级匹配较好,能很好地敏化Eu3+而发出明亮的红光,是获得Eu3+红色荧光发射的优良配体,认证了有机配体与稀土离子之间产生有效能量传递的前提是存在"天线效应".     

掺Tm~(3+)氟锆酸盐玻璃2μm发光特性

研究了Tm3+掺杂氟锆酸盐玻璃的2μm发光特性。通过吸收光谱,运用Judd-Ofelt(J-O)理论计算了J-O强度参量tΩ(t=2,4,6)以及Tm3+离子在玻璃中的自发辐射跃迁几率、荧光分支比和辐射跃迁寿命等光谱参数。采用808 nm激光二极管(LD)抽运,获得了Tm3+离子在氟锆酸盐玻璃中的近2μm发射光谱。Tm3+离子在玻璃中的3F4→3H6跃迁峰值波长位于1.82μm处。研究表明,随着Tm3+离子浓度的增加,Tm3+离子之间发生明显的交叉弛豫过程(3H4→3F4,3F4→3H6),从而使得1.82μm处荧光强度明显增强,但当掺杂浓度进一步增加达到一定程度后,基于三能级稀土离子的浓度猝灭效应,该荧光强度明显降低。研究计算了氟锆酸盐玻璃中Tm3+…3F4→3H6跃迁对应的受激发射截面,结果表明,受激发射截面受Tm3+掺杂浓度的影响不大。     

Eu(TTFA)3掺杂环氧基光刻胶薄膜的强烈红色荧光

合成了稀土配合物Eu(TTFA)3（TTFA, 2 thenoyltrifluoroacetone）掺杂的环氧基紫外负性光刻胶薄膜,采用荧光分光光度计对其光致发光特性进行了系统表征.荧光光谱分析表明,Eu(TTFA)3掺杂的光刻胶薄膜具有很宽的激发谱带（200 ~ 400 nm）,且在长波紫外区表现为强激发,说明有机配体TTFA-与中心离子之间存在着比电荷迁移带更有效的能量传递.配体TTFA-的三重激发态和Eu3+的激发态能级匹配较好,能很好地敏化Eu3+而发出明亮的红光,是获得Eu3+红色荧光发射的优良配体,认证了有机配体与稀土离子之间产生有效能量传递的前提是存在“天线效应”.     

Er3+单掺和Er3+/Yb3+共掺碲酸盐玻璃的光谱性质及能量传递

采用高温熔融法制备了新型Er3+单掺和Er3 +/Yb3+共掺的TeO2-Bi2O3-SiO2-B2O3玻璃,测试并分析了样品的吸收光谱、发射光谱以及Er3 +/Yb3共掺杂样品的发射光谱和荧光寿命.计算出了玻璃的J-O强度系数Ωt(t=2,4,6);系统讨论了Er3+/Yb3+共掺杂样品在808 nm激光激发下,Yb...     

Eu3+掺杂Bi2O3-TeO2-B2O3-ZnO玻璃光谱性质

测量了Eu3+（1 mol%）掺杂(60-χ)Bi2O3-χ TeO2-30B2O3-10ZnO（χ＝5,10,20,30,摩尔百分比）玻璃的吸收光谱、发射光谱、激发光谱以及声子边带谱.根据稀土离子Eu3+光学跃起矩阵元的特点,从发射光谱获得了Eu3+光学跃起的J-O参数Ω2与Ω4.结果显示,强度参量Ω2随着Bi2O3量的增加与TeO2量的减少而减小,表明材料的对称性提高, Eu-O键强减弱,共价性减弱.随着Bi2O3量的增加,电－声子偶合减弱,材料的热稳定性大幅度提高.     

掺铥PLZT透明光电陶瓷的光辐射特性

根据J-O理论研究掺Tm3+的光电陶瓷PLZT的激光潜能，利用Tm3+的420?2000 nm的吸收光谱拟合出了其强度参量，即?2=9.133￡10-21 cm2, ?4=1.529￡10-21 cm2和?6=1.712￡10-21 cm2，进而由强度参量计算了辐射跃迁几率、辐射寿命、荧光分支比和1865 nm荧光峰的受激发射截面等光学参数．     

掺Tm3+有机-无机复合材料的合成及光谱参数计算

以正硅酸乙酯与γ-(2,3-环氧丙氧基)丙基三甲氧基硅烷为前驱体,应用溶胶-凝胶技术,合成了Tm3+离子掺杂的有机-无机复合材料。从吸收光谱特性出发,应用Judd-Ofelt理论,计算得到了Tm3+离子的J-O强度参量(Ω2,Ω4,Ω6)及Tm3+离子各激发能级的自发辐射跃迁概率、荧光分支比及辐射寿命等光谱参量。根据McCumber理论计算了Tm3+离子能级3H6←→3F4(1.8μm)跃迁的吸收截面和受激发射截面,同时,根据所获得的吸收截面、发射截面以及掺杂离子浓度等参数获得了Tm3+离子在凝胶玻璃中的增益截面函数。与其它玻璃掺杂基质比较可知,Tm3+掺杂的有机改良硅酸盐玻璃在～1.8μm和～2.0μm波段的中红外激光中有潜在的应用前景。     

掺钕钆镓石榴石激光晶体光谱分析

掺钕钆镓石榴石(Nd3+: Gd3 Ga5 O12,简称Nd : GGG)激光晶体是固体热容激光器的首选工作物质.采用提拉法生长了Nd:GGG晶体,测试了晶体的吸收及荧光光谱,并利用J-O理论计算了晶体的吸收及发射截面、强度参数、辐射跃迁概率、荧光分支比、荧光寿命等光谱参数.吸收光谱测试及计算结果发现,Nd:GGG晶体的最强吸收峰位于808 nm附近,主峰808 nm的吸收截面积σabs=4.35×10-20cm2,吸收线宽FWHM为8 nm,并且吸收峰强度随掺杂离子浓度的增加而增加.荧光光谱测试及计算结果表明,晶体的最强荧光发射峰位于1 062 nm附近,是Nd3+的4F3/2-4I11/2能级跃迁产生的荧光发射.主发射峰1 062 nm辐射跃迁概率AJJ'=1 832.01 s-1,荧光分支比βJJ=45.07%,荧光寿命τ=250 μs,受激发射截面σ(λ)=21.58×10-20cm2,较大的荧光分支比和受激发射截面易实现4F3/2-4I11/2通道的激光运转.     

Eu3+配合物掺杂聚合物的制备与光谱性能研究

以噻吩甲酰三氟丙酮(2-thenoyltrifluoroacetone , TTFA), 六氟乙酰丙酮(hexafluoro- acetylacetone, HFA)和甲基联苯甲酰(dibenzoylmethide, DBM) 分别为配体合成了Eu3+的三种β-二酮类配合物Eu(TTFA)3、Eu(HFA)3和 Eu(DBM)3,以及掺杂这三种配合物的聚合物（聚甲基丙烯酸甲酯,PMMA）,并用分光光度计对它们的荧光光谱特性进行了分析研究.结果表明,三种配合物中Eu(TTFA)3荧光强度最强,并分析了其原因,发现能级匹配、配体取代基、配体结构对称性等均对配合物发光效率有重要的影响.通过比对,证明了TTFA是Eu3+发红色荧光的优良配体.进一步研究还发现,Eu(TTFA)3掺杂PMMA中稀土离子的荧光强度和荧光寿命均随掺杂浓度（质量分数为0.08～0.5）的增加而增大.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.