On the kinetics of thermal electron attachment to perfluoroethers

In this Letter we report the results of the measurements of the rate coefficients for thermal attachment to several perfluoroethers namely perfluorodiglyme (C₆F₁₄O₃), perfluorotriglyme (C₈F₁₈O₄), perfluoropolyether (CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃) and perfluorocrownether ((C₂F₄O)₅). Rate coefficients were obtained under thermal conditions in the temperature range 298–378 K. The increase of the rates with temperature follows the Arrhenius law and the activation energies have been obtained from the slope of the ln(k) vs. 1/T. The respective values of the rate coefficients (at 298 K) and activation energies are as follows: 7.7 ± 1.2 × 10^?11 cm³ s^?1 (0.18 ± 0.005 eV), 6.7 ± 2.1 × 10^?11 cm³ s^?1 (0.25 ± 0.004 eV), 2.1 ± 0.2 × 10^?10 cm³ s^?1 (0.16 ± 0.010 eV), 3.1 × 10^?11 cm³ s^?1 (0.27 ± 0.003 eV) for C₆F₁₄O₃, C₈F₁₈O₄, CF₃–(OCF(CF₃)CF₂)_n–(OCF₂)_m–OCF₃ and (C₂F₄O)₅.     

Temperature dependence on the dose response of the Fricke–gelatin–xylenol orange gel dosimeter

The effect of temperature during optical absorbance measurements and irradiation on the values of the molar absorption coefficient, (ε_m)_t, and radiation chemical yield, G_t^′, respectively, for the Fricke–gelatin–xylenol orange (FGX) gel dosimeter were investigated. At 20 °C, the product (ε_m)_tG_t^′ was found to be 6.76×10^?3 m² J^?1. While an irradiation temperature coefficient, k₂, was evident (?0.53% °C^?1), no temperature effect was found during measurement in the range 16–25 °C.     

Dyed polyvinyl chloride films for use as high-dose routine dosimeters in radiation processing

Characteristics of the polyvinyl chloride (PVC) films containing 0.11 wt% of malachite green oxalate or 6GX-setoglausine and about 100 μm in thickness were studied for use as routine dosimeters in radiation processing. These films show basically color bleaching under irradiation with ⁶⁰Co γ-rays in a dose range of 5–50 kGy. The sensitivity of the dosimeters and the linearity of dose-response curves are improved by adding 2.5% of chloral hydrate [CCl₃CH(OH)₂] and 0.15% hydroquinone [HOC₆H₄OH]. These additions extend the minimum dose limit to 1 kGy covering dosimetry requirements of the quality assurance in radiation processing of food and healthcare products. The dose responses of both dyed PVC films at irradiation temperatures from 20°C to 35°C are constant relative to those at 25°C, and the temperature coefficients for irradiation temperatures from 35°C to 55°C were estimated to be (0.43±0.01)%/°C. The dosimeter characteristics are stable within 1% at 25°C before and 60 days after the end of irradiation.     

The effect of irradiation temperature on the quality improvement of Kimchi,Korean fermented vegetables,for its shelf stability

The present study was conducted to evaluate the effect of irradiation temperature on the shelf stability and quality of Kimchi during storage at 35 °C for 30 days. Kimchi samples were N₂-packaged and heated at 60 °C and then gamma irradiated at 20 kGy under various temperatures (room temperature, ice, dry ice, and liquid nitrogen). In the results of microbial, pH, and acidity analysis, combination treatment of heating and irradiation was able to sterilize microbes in Kimchi regardless of irradiation temperature. When Kimchi was irradiated under frozen temperatures, especially dry ice, the softening of texture and the deterioration of sensory quality of Kimchi were reduced. Also, ESR signal intensities were weakened due to the decrease of irradiation dose and temperature.     

Temperature dependence of the free volume in polytetrafluoroethylene studied by positron annihilation spectroscopy

The temperature dependence of the free volume holes in pure polytetrafluoroethylene (PTFE) and doped with 25% glass have been studied in the temperature range (30–250 °C) using positron annihilation lifetime spectroscopy. The data clearly revealed the glass transition temperatures for pure and doped PTFE are 130 and 110 °C, respectively. As the temperature increases, the free volume distribution becomes positioned at larger free volume hole size. A good correlation between the electrical conductivity and the o-Ps parameters was achieved.     

Phase transitions of CaTiO3 ceramics sintered with the aid of NaF and MgF2

New phases with initial composition (1 ? x)CaTiO₃ ? xNaF ? xMgF₂ (0 ≤ x ≤ 0.20) have been prepared at low temperature (950 °C) from mixtures of CaTiO₃ and fluorides NaF and MgF₂. The oxyfluorides obtained have been characterized by X-ray diffraction at room temperature and indexed by isotypy with orthorhombic CaTiO₃. The microstructures of these phases are observed by scanning electron microscopy. Dielectric measurements have been carried out during cooling cycle from 500 °C to room temperature at two frequencies (100 Hz, 1 kHz). Differential scanning calorimetry (DSC), thermogravimetry (TG) and differential thermogravimetry (DTG) analyses have been performed, respectively, from room temperature up to 550 °C (DSC) and 920 °C (TG–DTG). The dielectric measurements revealed two anomalies which have been confirmed by DSC analyses. These phenomena are ascribed to second order phase transitions. The variation of the real permittivity with temperature is in agreement with the class I capacitor specifications. However, the dielectric losses have to be improved.     

Preparation via microemulsion method and proton conduction at intermediate-temperature of BaCe1−xYxO3−α

The ceramic powders of BaCe_1?xY_xO_3?α (x = 0.05, 0.10, 0.15, 0.20) have been prepared via a microemulsion method. Green compacts of the powders were sintered to densities higher than 95% of theoretical at the lower temperature (1500 °C). The obtained ceramics showed a single-phase of orthorhombic perovskite. The proton conduction was investigated by employing the techniques of AC impedance and electrochemical hydrogen permeation (hydrogen pumping) at 300–600 °C. It was found that the ceramics were almost pure proton conductors in wet hydrogen, and the highest proton conductivity was observed for x = 0.15 at 600 °C. Ammonia was synthesized successfully from nitrogen and hydrogen at atmospheric pressure in the electrolytic cell using BaCe_0.85Y_0.15O_3?α. The maximum rate of NH₃ formation was found to be 2.1 × 10^?9 mol s^?1 cm^?2 at 500 °C with an applied current of 0.75 mA.     

Molecular characterization of Ulex europaeus biochar obtained from laboratory heat treatment experiments – A pyrolysis–GC/MS study

Gorse species (Ulex sp.) are ubiquitous in the shrublands of NW Spain and have the potential to become key players in an integral biofuel/biochar program in NW Spain. Here we present molecular characterization (using pyrolysis–GC/MS) of a biochar “thermosequence” obtained by laboratory heating of Ulex europaeus wood in a muffle furnace between 200 and 600 °C (T_CHAR). Low temperature chars (T_CHAR ≤ 350 °C) produced significant amounts of pyrolysis products of which the precursor biopolymer could be recognized, while high-temperature chars (T_CHAR ≥ 400 °C) produced mainly phenols and monocyclic and polycyclic aromatic hydrocarbons, which are not specific for any biopolymer. Carbohydrate could hardly be recognized at T_CHAR ≥ 350 °C. The thermal rearrangement of polyphenols, mainly lignin, was reflected in more detail (1) C₃-side chain shortening and probably depolymerization (T_CHAR 200–350 °C), (2) demethoxylation of syringyl and probably also some guaiacyl lignin (T_CHAR 300–400 °C), (3) elimination of virtually all remaining methoxyl groups (T_CHAR 350–400 °C), through dehydroxylation and demethoxylation, (4) almost complete dehydroxylation of lignin and other biopolymers (T_CHAR 400–500 °C), (5) progressive condensation into polyaromatic structures (T_CHAR 300–500 °C) and (6) partial elimination of alkyl bridges between (poly)aromatic moieties (T_CHAR 450–500 °C). These results were supported by Fourier transform infrared spectroscopy (FTIR) of the same samples. We conclude that pyrolysis–GC/MS can be used as a rapid molecular screening method of gorse-derived biochar. Molecular properties elucidation is an essential part of predicting the stability and agronomical behavior of gorse-derived biochar after future implementation in soils.     

Kinetic study of nucleophilic reactivity of heterocyclic amines with 4,6-dinitrobenzofuroxan in acetonitrile

The reaction kinetics of 4,6-dinitrobenzofuroxan with five heterocyclic amines was investigated spectrophotometrically (UV–Vis) in acetonitrile at 20 °C. It was observed that the rate constants of these reactions increased as follows: 2-aminopyrimidine > 2-aminothiazole > 2-aminobenzothiazole > 5-amino-3,4-dimethylisoxazole > 2-amino-5-trifluoromethyl-1,3,4-thiadiazole. Further, second-order rate constants (k₁) pertaining to the C–N and C–C bond forming step of these complexation processes fit to the three parameter equation log k (20 °C) = s_N (N + E), allowing the determination of the nucleophilicity parameters (N) of the five heterocyclic amines. The heterocyclic amines were subsequently ranked on the comprehensive nucleophilicity scale defined by Mayr et al. (2003), providing a direct comparison of n-, π-, and σ-nucleophiles.     

Experimental evaluation of a uniform transmembrane pressure crossflow microfiltration unit for the concentration of micellar casein from skim milk

A uniform transmembrane pressure (UTMP) crossflow microfiltration (CFMF) system maintains a low but uniform transmembrane pressure (ΔP_TM) with high crossflow velocity (CFV), which reduces fouling and cake build-up, and improves the utilization of available filtration area. A CFMF system, with a 0.2 μm nominal pore size ceramic filter, filtration area 0.184 m², was operated in both UTMP and non-UTMP modes. The two modes were compared for their effectiveness in maintaining a steady flux during the separation of casein micelles from skim milk up to a concentration factor (CF) 10 at 50°C. Experiments were performed at an average CFV of 7.2 m s⁻¹ and ΔP_TM from 89 to 380 kPa. Up to CF 4 the non-UTMP mode maintained a slightly better flux and process time than the UTMP mode, but reached the minimally acceptable flux (below 0.005 kg m⁻² s⁻¹) at CF 6. Depending upon the ΔP_TM maintained, the UTMP mode approached the minimal flux at CF 7 or 10 depending upon the combination of ΔP_TM and CFV used. Cake resistance (R_cm) was modified to include the effect of an increase in retentate viscosity with concentration. R_cm increased for the non-UTMP mode and decreased for the UTMP mode with a decrease in the ratio of permeation flux/wall shear stress (J_p/τ_w) (which occurred as the retentate gets concentrated). This indicated that the cake formed during the non-UTMP mode of operation was more compact and durable (harder to erode) than in the UTMP mode. A central composite rotatable design estimated the optimal operating region at a CFV of 7.1 m s⁻¹ and ΔP_TM of 241±10 kPa to achieve maximum flux and a high concentration.     

Separation of hydrogen from steam using a SiC-based membrane formed by chemical vapor deposition of triisopropylsilane

A silicon carbide-based membrane was formed in the macropores of an α-alumina support tube by chemical vapor deposition of triisopropylsilane at 700–800°C with a forced cross-flow through the porous wall. The membrane permeated gases except H₂O mainly by the Knudsen diffusion mechanism at permeation temperatures of 50–400°C. The H₂/H₂O selectivity was near or below unity because of the hydrophilic nature of the membrane. After a heat-treatment in Ar at 1000°C for 1 h, however, the membrane formed at a final evacuation pressure of 1 kPa exhibited a H₂/H₂O selectivity of 3–5, for a mixed feed of H₂–H₂O–HBr system, associated in a thermochemical water-splitting process. The H₂ permeance was (5–6)×10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at 50–400°C. The membrane maintained the H₂/H₂O selectivity for more than 100 h in the H₂–H₂O–HBr mixture at 400°C.     

Doping effects of Yb3+ on the crystal structures,nanoparticle properties and electrical behaviors of ZrO2 derived from a facile urea-based hydrothermal route

Weakly-agglomerated nanocrystalline (ZrO₂)_1−x(Yb₂O₃)_x (x=0.02–0.2) powders with high surface area (109–151 m² g⁻¹) were synthesized by a two-step hydrothermal process in the presence of urea: a stock solution of metal nitrates and urea was heated at 80 °C for 24 h and then at 180 °C for 48 h. For x=0.04–0.2, the as-derived powders were an assembly of uniform nanoparticles with well-defined edges in the size between 6.1–8.4 nm. Before and after calcination at 800 °C, the lattice parameters, microstrain and surface area of the (ZrO₂)_1−x(Yb₂O₃)_x samples tended to increase with Yb³⁺ concentration; while, the average crystallite size decreased correspondingly. In the Arrhenius plots over the measurement temperature range of 400–800 °C, the bulk ionic conductivity of the compacts sintered at 1400 °C for 24 h showed a maximum value at the composition of x=0.08 in cubic structure, with an activation energy of 0.89 eV. At 800 °C, σ_b=0.049 S cm⁻¹ for x=0.08.     

The electrochemical properties of thermophilic cytochrome P450 CYP119A2 at extremely high temperatures in poly(ethylene oxide)

The electrochemical measurements were carried out by using thermophilic cytochrome P450 CYP119A2 (P450st) modified with poly(ethylene oxide) (PEO) in PEO₂₀₀ as an electrochemical solvent. The PEO modified P450st gave clear reduction–oxidation peaks by cyclic voltammetry in oxygen-free PEO₂₀₀ up to 120 °C. The midpoint potential measured for the P450st was −120 mV vs. [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ at 120 °C. The peak separation, ΔE, was 16 mV at 100 mV/s. The estimated electron transfer rate of PEO-P450st at 120 °C was 35.1 s⁻¹. The faster electron transfer reaction was achieved at higher temperatures. The electrochemical reduction of dioxygen was observed at 115 °C with the PEO-modified P450st system.     

Preferential crystallization in an unusual case of conglomerate with partial solid solutions

Ethanolamine mandelate (E.M.) crystallizes as a stable conglomerate and has been found to form partial solid solutions. The crystal structure of the pure enantiomer has been solved from single-crystal X-ray diffraction. In order to determine the extreme compositions of the partial solid solutions in equilibrium (87% ee), the isothermal ternary section in the system [(+)-E.M.–(−)-E.M.–(ethanol–water azeotropic mixture)] was established at 25 °C. Several consecutive preferential crystallization attempts (AS3PC method) were undertaken between T_B = 41 °C (starting temperature) and T_F = 25 °C (final temperature) on a 2-L scale.We initially expected to obtain crude crops whose enantiomeric purities would be close to that defined by the isothermal ternary phase diagram (T_F). In fact, the filtered solid phases are of lower enantiomeric excesses: ca. 62% ee. The monitoring of the mother liquor composition over the course of the entrainment shows that the enantiomeric composition of the filtered solid is related to the metastable equilibria involved in the preferential crystallization.     

Gamma-ray response of a clear,crosslinked PMMA dosimeter,Radix W

Radix W, a clear poly(methyl-methacrylate) (PMMA) dosimeter was developed with improved properties compared to the conventional clear PMMA dosimeter, Radix RN15. PMMA with a glass transition temperature (T_g) higher than 120 °C was selected making it possible to measure doses in a wide range of 1 to 150 kGy. Dose rates of 2.5–10 kGy/h were tested and did not affect significantly the dose response. The influence of irradiation temperature was reduced compared with Radix RN15.     

Reactions of the HO2 radical with OH,H, Fe2+ and Cu2+ at elevated temperatures

The temperature dependence of the rate constant for the reactions of HO₂ with OH, H, Fe²⁺ and Cu²⁺ has been determined using pulse radiolysis technique. The following rate constants, k (dm³ mol⁻¹ s⁻¹) at 20°C and activation energies, E_a (kJ mol⁻¹) have been found. The reaction with OH was studied in the temperature range 20–296°C (k=7.0×10⁹, E_a=7.4) and the reaction with H in the temperature range 5–149°C (k=8.5×10⁹, E_a=17.5). The reaction with Fe²⁺ was studied in the temperature range 16–118°C (k=7.9×10⁵, E_a=36.8) and the reaction with Cu²⁺ in the temperature range 17–211°C (k=1.1×10⁸, E_a=14.9).     

Preparation of a new lightly cross-linked liquid crystalline polyamide by interfacial polymerization. Application to the obtainment of microcapsules with photo-triggered release

Microcapsules based on a new liquid crystalline lightly cross-linked polyamide, in which the state of order can be triggered by means of external stimuli, such as temperature and light, were prepared by interfacial polymerization. This polyamide exhibited a nematic phase up to 166 °C and it started to decompose at 340 °C; morphological variations of the film were observed by Scanning Electron Microscopy in correspondence to the clearing temperature; moreover, by continuous irradiation with UV light at room temperature, the polymer underwent E–Z photoisomerization. The prepared microcapsules contained either toluene, or concentrated solutions of naphthalene or β-carotene, as the core; in all cases, their outer surface appeared smooth and dense, while heterogeneities could be seen on the inner face. Capsule diameter lay in the range 30–120 μm, depending on the encapsulated material, with quite narrow size distributions. To the authors’ knowledge, this is the first example of microcapsules whose shell is completely constituted by a liquid crystalline lightly cross-linked polymer. Release experiments of β-carotene were performed in water and in tetrahydrofuran. β-Carotene release in water at 20 °C was strongly influenced by UV irradiation: in the absence of irradiation, it was practically negligible while, when microcapsules were submitted to continuous irradiation with UV light, β-carotene was quickly released and reached 100% release after 5 min. Preliminary experiments concerning the effect of temperature and of a swelling solvent, such as THF, on release, were also performed.     

Enhanced electrical conductivity in Ce0.79Gd0.20Co0.01O2−δ for low temperature solid oxide fuel cell applications

Very high electrical conductivity of ～0.021 S/cm at 600 °C is obtained in Ce_0.79Gd_0.20Co_0.01O_2?δ. Corresponding activation energy of conduction ～0.43 eV measured in the temperature range of 400–700 °C is found to be notably low. Improved electrical properties with 99% of the theoretical density as obtained for these specimens, prepared using powder of average particle size ～20 nm and subsequent sintering at 1100 °C, is considered to be a significant step to reduce the processing temperature. The measured electrical potential of ～1 V indicates the suitability of its use as an electrolyte in electrochemical devices.     

Thermogravimetric and FTIR studies of chitosan blends

Results of spectrophotometric and thermogravimetric studies of chitosan (CH) blends with polyvinyl alcohol (PVAL), starch (S) and hydroxypropylcellulose (HPC) obtained by casting from solutions in the form of transparent films containing 0–1.0 weight fraction of CH were discussed. Blends containing S are homogeneous only in the case of low-weight fraction of S (to 0.3).On the basis of results of thermodegradation in dynamic and isothermal conditions, thermal stability of the tested systems was estimated. Thermogravimetric measurements in dynamic conditions were carried out in the temperature range of 100–450 °C at constant heating rate 15 °C/min. From thermogravimetry (TG) and DTG curves the activation energy and characteristic parameters of degradation of the tested blends were determined. The observed growth of activation energy and T_p—temperature of initial weight loss, T_max—temperature of maximal rate and C_e—degree of conversion at the end of the measurement (at temperature 450 °C) along with the increase of polymer fraction (HPC and S) in the CH blend provides an evidence of improved thermal stability of the systems tested.Investigations in isothermal conditions in air at temperature from 100 to 200 °C confirmed appreciable improvement of CH thermal stability in the blends being tested.Infrared spectroscopic analysis of the blends showed a distinct stabilization of the process of chain scission. In the band at 1080 cm⁻¹ associated with absorption in –C–O–C– group during degradation of the blends at temperature 200 °C much smaller decrease due to molecular scission were observed than in the case of pure CH.     

Influence of thermal treatment on the glass transition temperature of thermosetting epoxy laminate

The influence of accelerated thermal treatment of thermosetting epoxy laminate on its glass transition temperature was studied. Lamplex^® FR-4 glass fibre-reinforced epoxy laminate (used for printed circuit board manufacturing) was used in these experiments. The composite was exposed to thermal treatments at temperatures ranging from 170 °C to 200 °C for times ranging from 10 to 480 h. The glass transition temperature (T_g) was analysed via dynamic mechanical analysis (DMA). It has been proven that the glass transition temperature rapidly decreases in reaction to thermal stress. The obtained T_g data were used for Arrhenius plots for different critical temperatures (T_g-crit. = 105–120 °C). From their slopes (?E_a/R), the activation energy of the thermal degradation process was calculated as 75.5 kJ/mol. In addition to this main relaxation mechanism, DMA also recorded one smaller relaxation process in the most aged samples. Microscopic analysis of the sample structure showed the presence of pronounced small regions of degradation both on the surface and in the inner structure, which are probably the causes of microscopic delamination and the smaller relaxation process.