K-edge angiography utilizing a tungsten plasma X-ray generator in conjunction with gadolinium-based contrast media

The tungsten plasma flash X-ray generator is useful in order to perform high-speed enhanced K-edge angiography using cone beams because K-series characteristic X-rays from the tungsten target are absorbed effectively by gadolinium-based contrast media. In the flash X-ray generator, a 150 nF condenser is charged up to 80 kV by a power supply, and flash X-rays are produced by the discharging. The X-ray tube is a demountable diode, and the turbomolecular pump evacuates air from the tube with a pressure of approximately 1 mPa. Since the electric circuit of the high-voltage pulse generator employs a cable transmission line, the high-voltage pulse generator produces twice the potential of the condenser charging voltage. At a charging voltage of 80 kV, the estimated maximum tube voltage and current were approximately 160 kV and 40 kA, respectively. When the charging voltage was increased, the characteristic X-ray intensities of tungsten K_α lines increased. The K_α lines were clean, and hardly any bremsstrahlung rays were detected. The X-ray pulse widths were approximately 110 ns, and the time-integrated X-ray intensity had a value of approximately 0.35 mGy at 1.0 m from the X-ray source with a charging voltage of 80 kV. Angiography was performed using a film-less computed radiography (CR) system and gadolinium-based contrast media. In angiography of non-living animals, we observed fine blood vessels of approximately 100 μm with high contrasts.     

A new X-ray pinhole camera for energy dispersive X-ray fluorescence imaging with high-energy and high-spatial resolution

A new X-ray pinhole camera for the Energy Dispersive X-ray Fluorescence (ED-XRF) imaging of materials with high-energy and high-spatial resolution, was designed and developed. It consists of a back-illuminated and deep depleted CCD detector (composed of 1024 × 1024 pixels with a lateral size of 13 μm) coupled to a 70 μm laser-drilled pinhole-collimator, positioned between the sample under analysis and the CCD. The X-ray pinhole camera works in a coaxial geometry allowing a wide range of magnification values.The characteristic X-ray fluorescence is induced on the samples by irradiation with an external X-ray tube working at a maximum power of 100 W (50 kV and 2 mA operating conditions).The spectroscopic capabilities of the X-ray pinhole camera were accurately investigated. Energy response and energy calibration of the CCD detector were determined by irradiating pure target-materials emitting characteristic X-rays in the energy working-domain of the system (between 3 keV and 30 keV).Measurements were performed by using a multi-frame acquisition in single-photon counting. The characteristic X-ray spectra were obtained by an automated processing of the acquired images. The energy resolution measured at the Fe–Kα line is 157 eV.The use of the X-ray pinhole camera for the 2D resolved elemental analysis was investigated by using reference-patterns of different materials and geometries. The possibility of the elemental mapping of samples up to an area of 3 × 3 cm² was demonstrated.Finally, the spatial resolution of the pinhole camera was measured by analyzing the profile function of a sharp-edge. The spatial resolution determined at the magnification values of 3.2 × and 0.8 × (used as testing values) is about 90 μm and 190 μm respectively.     

Comparison between blackbody radiation and continuous X-ray spectra produced by electron deceleration

The continuous X-ray spectral profiles are compared with the Planck's distribution law for blackbody radiation. The energy distributions of continuum X-rays produced by bombardments of 20 and 30 kV electron beams onto iron target are crudely reproduced by the blackbody radiation at about 10⁷ K temperature at their absolute intensity scale.     

Quantitative analysis of single aerosol particles using polycapillary X-ray optics

A laboratory micro X-ray fluorescence spectrometer based on polycapillary X-ray optics (PXRO) was used to carry out the quantitative X-ray fluorescence analysis of single aerosol particles with smaller size than that of focal spot of PXRO. The minimum detection limits measured with the thin-film reference standards were in the range from 13.3 to 0.7 ng cm^? 2 when the operating current and voltage were 70 mA and 35 kV, respectively. In order to reduce the effects of the inhomogeneous distributions of the X-ray intensity in the focal spot of the PXRO on the analysis results, the sensitivities were corrected by using a Gaussian function for the quantitative analysis of single aerosol particles. The accuracy of the analysis of single standard solution drops was on average 25% depending on the element and concentration. The precision of the analysis was better than 5%.     

The investigations on K and L X-ray fluorescence parameters of gold compounds

The study aimed to determine the chemical effects on the K and L X-ray intensity ratios and the K and L X-ray production cross sections for gold compounds. The K shell fluorescence yields and L shell average yields were also investigated. The samples were excited by 59.5 keV γ-rays from an ²⁴¹Am annular radioactive source and 123.6 keV γ-rays from a ⁵⁷Co annular radioactive source. K and L X-rays emitted from samples were counted by an Ultra-LEGe detector with a resolution of 0.150 keV at 5.9 keV. The experimental values were compared with theoretical, the semi-empirical and other experimental values.     

The improvement of the Li-ion insertion behaviour of Li1.05Cr0.10Mn1.85O4 in an aqueous medium upon addition of vinylene carbonate

The influence of vinylene carbonate addition to aqueous LiNO₃ solution on the Li-ion insertion performance of a Li_1.05Cr_0.10Mn_1.85O₄ was studied by galvanostatic charging/discharging. Without additive, the coulombic capacity amounted initially to 80 mA h g^?1 and, during 50 galvanostatic charging/discharging cycles, decreased to 44.1% of the initial value. Upon VC addition in an amount of 1 wt.%, the initial discharge capacity of 112 mA h g^?1 was registered which after 100th charging/discharging cycles retained even 82% of the initial value. This is the first report of a successful use of an additive to improve the behaviour of a Li-intercalation material in an aqueous solution.     

Recovery of a multicomponent,single phase aerosol with a difference in vapor pressures entrained in a large air flow

Effective heat transfer coefficients and mass transfer rates were determined at varying compositions of steam with 1.5% by weight volatile oils entrained in an air flow. The mixture of volatile oils is comprised of 50% menthol, 25% menthone, and other fractions of essential oils. The rate of transient mass transfer, relative partial pressures and the liquid phase resistances were used to evaluate recovery mechanisms for the volatile oils in the entrained aerosol. The size of the aerosol was (600 ± 50) μm. A stainless steel tube and shell condenser and a direct contact condenser were constructed in order to evaluate unsteady state models for mass transfer of the volatile oils, the unsteady state heat transfer, and the percent recovery of the aerosol. These data will be invaluable in the development of a collection and condensation system for the continuous microwave processing of mint hay. The Solvent Free Microwave System? vaporizes water and essential oils directly from cut hay. The coupled ionized interior of the microwave applicator seeds ions in the gas phase which provide a ready platform for aerosol nucleation of the steam in the air mixture. This aerosol must be recovered at an efficiency which rivals steam distillation.     

Signal enhancement in solution-cathode glow discharge — optical emission spectrometry via low molecular weight organic compounds

HCOOH, CH₃COOH, and CH₃CH₂OH were used as chemical modifiers in a solution-cathode glow discharge. Emission was measured directly from the discharge, without a gas–liquid separator or a secondary excitation source. Emission from Ag, Se, Pb, and Hg was strongly enhanced, and the detection limits (DL) for these elements were improved by up to an order of magnitude using a combination of HCOOH and HNO₃ compared to using HNO₃ alone. The DL was measured for Mg (1 μg/L), Fe (10 μg/L), Ni (6 μg/L), Cu (6 μg/L), Pb (1 μg/L), Ag (0.1 μg/L), Se (300 μg/L), and Hg (2 μg/L). Coefficients of determination (R²) were between 0.9986 and 0.9999. A voltage of 1 kV was used, which produced a current of approximately 70 mA.     

Effect of electrical charging on scanning electron microscopy-energy dispersive X-ray spectroscopy analysis of insulating materials

We investigated the conditions under which we can obtain reasonable qualitative results in scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) analysis of trace elements in insulating materials using a diluted ionic liquid (EMI-CH₃COO) and changing probe current. Below 100 nA, electrical charging of insulating materials was prevented. The probe current of 10 nA was suitable for qualitative analysis because the intensities of peaks from these materials were strong enough to detect trace elements at the concentration of 0.1 wt.% in the sample without interference by sum peaks. Diluted EMI-CH₃COO can also be used for SEM-EDX quantitative analysis of insulating materials as discharging agents. In contrast, when insulating materials were electrically charged, the obtained spectra contained characteristic X-rays of the insulating materials with low energies and of materials other than the samples such as the sample stage and the collimator in the X-ray detector. This is because electrons from the electron beam were decelerated by and deflected from the insulating materials. By coating the insulating materials with the diluted EMI-CH₃COO, the deceleration and deflection of the electron beam were prevented.     

A room temperature solid-state rechargeable sodium ion cell based on a ceramic Na-β″-Al2O3 electrolyte and NaTi2(PO4)3 cathode

In this work, a room temperature solid-state rechargeable sodium ion cell, consisting of a ceramic Na-β″-Al₂O₃ thin film as the electrolyte, a NaTi₂(PO₄)₃ gel composite as the cathode and sodium metal as the anode, was developed for the first time. A dense Na-β″-Al₂O₃ thin film with a thickness of approximately 100 μm was obtained by non-toxic and hazard-free ceramic fabrication processes, including tape-casting and subsequent sintering. The solid-state sodium ion cell had a working window of 1.5–2.5 V upon charge-discharge processes and exhibited an extremely stable voltage plateau of approximately 2.1 V. A reversible capacity, based on the NaTi₂(PO₄)₃ cathode, of 133 mAh g^− 1 was observed during the first cycle, which remained approximately 100 mAh g^− 1 after 50 cycles.     

Bismuth nano-powder electrode for trace analysis of heavy metals using anodic stripping voltammetry

In the present work, a more sensitive and conveniently usable electrode sensor for a trace analysis of heavy metal was developed by using Bi nanopowder synthesized by levitational gas condensation (LGC) method. It was observed from the TEM image that the Bi nanopowder is spherical in shape with a size of nearly 50 nm. The XRD pattern revealed intense peaks which can be indexed as a rhombohedral structure of Bi without any other diffraction peaks corresponding to an oxide or an impurity. This indicates that the resulting nanopowder synthesized by the LGC method is a highly crystallized Bi with a high purity. The square wave anodic stripping voltammograms (SWASV), experimentally measured for the Bi nanopowder electrode, showed well-defined and highly reproducible electrochemical responses relating to the stripping of Cd and Pb. The detection limit of the electrode was estimated to be 0.15 μg/l and 0.07 μg/l for Cd and Zn, respectively, on the basis of the signal-to-noise characteristics (S/N = 3) of the response for the 1.0 μg/l solution under a 10 min accumulation.     

Thermochemistry of Pd–In,Pd–Sn and Pd–Zn alloy systems

The standard enthalpy of formation of several Pd–M alloys (M = In, Sn and Zn) has been measured using a high temperature direct drop calorimeter. The reliability of the calorimetric results has been determined and supported by using different analytical techniques: light optical microscopy, scanning electron microscopy equipped with electron probe microanalysis (EPMA with EDS detector) and X-ray powder diffraction analysis. The values of Δ_fH (kJ/mol atoms) for the following phases were obtained for the formation in the solid state at 300 K: PdIn (49 at.%In): ?69.0 ± 1.0; Pd₂In₃ ?57.0 ± 1.0; Pd₃In₇: ?43.0 ± 1.0; PdSn₂: ?50.0 ± 1.0; Pd₂Zn₉ (77 at.%Zn): ?33.7 ± 1.0; Pd₂Zn₉ (78 at.%Zn): ?34.0 ± 1.0; Pd₂Zn₉ (80 at.%Zn): ?35.0 ± 1.0. The results show exothermic values which increase from the Pd–Zn to the Pd–Sn and Pd–In systems; the data obtained have been discussed in comparison with those available in literature.     

FeAgMo2O8 — A novel oxygen evolution catalyst material for alkaline metal–air batteries

This paper reports about FeAgMo₂O₈ — a novel oxygen evolution catalyst material for secondary (rechargeable) metal–air batteries. Bifunctional air electrodes were made using FeAgMo₂O₈ as a charging catalyst for oxygen evolution reaction (OER) and silverized carbon black (Ag/C) was employed as a discharging catalyst for oxygen reduction reaction (ORR). Corresponding air electrodes were investigated using 10 M KOH as an electrolyte. At current densities between 20 and 50 mA per cm² we observed discharging and charging voltages of 1.20 to 1.15 V and 1.96 to 2.05 V, respectively.     

Sulfur doped reduced graphene oxide as metal-free catalyst for the oxygen reduction reaction in anion and proton exchange fuel cells

Sulfur doped reduced graphene oxide (S-rGO) is investigated for catalytic activity towards the oxygen reduction reaction (ORR) in acidic and alkaline electrolytes. X-ray photoelectron spectroscopy shows that sulfur in S-rGO is predominantly integrated as thiophene motifs within graphene sheets. The overall sulfur content is determined to be approximately 2.2 at.% (elemental analysis). The catalytic activity of S-rGO towards the ORR is investigated by both rotating disc electrode (RDE) and polymer electrolyte fuel cell (PEFC) measurements. RDE measurements reveal onset potentials of 0.3 V and 0.74 V (vs. RHE) in acidic and alkaline electrolyte, respectively. In a solid electrolyte fuel cell with S-rGO as cathode material, this is reflected in an open circuit voltage of 0.37 V and 0.78 V and a maximum power density of 1.19 mW/cm² and 2.38 mW/cm² in acidic and alkaline polymer electrolyte, respectively. This is the first report investigating the catalytic activity of a sulfur doped carbon material in both acidic and alkaline liquid electrolyte, as well as in both proton and anion exchange polymer electrolyte fuel cells.     

Electrochemical noise analysis of the effects of a magnetic field on cathodic hydrogen evolution

The effect of a static magnetic field on the evolution of hydrogen gas from a small platinum electrode in an aqueous electrolyte has been studied by recording the noise spectrum of overpotential voltage fluctuations at a constant current density of ?50 mA mm^?2. A 1/f² variation of the power spectrum characteristic of droplet coalescence is found for frequencies >10 Hz. The overpotential for hydrogen evolution decreases with applied field. When the production of gas bubbles is quasiperiodic, there is a threshold field of 0.5 T beyond which the size of the bubbles released is approximately doubled. This is explained by enhanced coalescence of small bubbles swept across the electrode surface by forced convection due to the Lorentz force.     

Lithium storage in perovskite lithium lanthanum titanate

Perovskite lithium lanthanum titanate (LLTO) was synthesized using sol–gel method. It shows a reversible capacity of 145 mA h g^− 1 and moderate cycling performance between 0.01 and 2.00 V. Cyclic voltammetry and X-ray diffraction results demonstrate a two-step solid–solution reaction behavior in the voltage range of 0.00–3.00 V upon lithium insertion/extraction. A stable solid electrolyte interphase (SEI) layer is formed on the surface of LLTO after the initial discharge. Carbon coating by chemical vapor deposition improves its cycling performance significantly.     

Plastic–polymer composite electrolytes: Novel soft matter electrolytes for rechargeable lithium batteries

We present here a soft matter solid composite electrolyte obtained by inclusion of a polymer in a semi-solid organic plastic lithium salt electrolyte. Compared to lithium bis-trifluoromethanesulfonimide-succinonitrile (LiTFSI-SN), the (100 − x)%-[LiTFSI-SN]: x%-P (P: polyacrylonitrile (PAN), polyethylene oxide (PEO), polyethylene glycol dimethyl ether (PEG)) composites possess higher ambient temperature ionic conductivity, higher mechanical strength and wider electrochemical window. At 25 °C, ionic conductivity of 95%-[0.4 M LiTFSI-SN]: 5%-PAN was 1.3 × 10⁻³ Ω⁻¹ cm⁻¹ which was twice that of LiTFSI-SN. The Young’s modulus (Y) increased from Y → 0 for LiTFSI-SN to a maximum ∼1.0 MPa for (100 − x)%-[0.4 M LiTFSI-SN]: x%-PAN samples. The electrochemical voltage window for composites was approximately 5 V (Li/Li⁺). Excellent galvanostatic charge/discharge cycling performance was obtained with composite electrolytes in Li|LiFePO₄ cells without any separator.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Fluorescence detection and identification of eight sulphonamides using capillary electrophoresis on released excipients in lake water

A simple and sensitive capillary electrophoresis method with fluorescence detection was developed for the determination of sulphanilamide, sulphamerazine, sulphacetamide and sulphanilic acid, sulphathiazole, Sulphisomidine, sulphadoxine and sulphadiazine in lake water. The sulphonamides were extracted from lake water, derivatized with fluorescamine and determination of sulphonamide was achieved using 20 mM borate buffer of pH 9.5 at an applied voltage of 25 kV. Detection was performed using UG-11 excitation filter of 405 nm and 495 nm emission filters. A fast, simple and sensitive method with limit of detection in the range 0.89–1.43 n mol L⁻¹ for all the eight sulphonamides with good recoveries of 80–110% is seen. Inter-day and intra-day validation of the separation method shows fairly good results. The detection and quantification limits for this newly developed method are too low to determine drug residues in lake water.     

Rapid anodic growth of TiO2 and WO3 nanotubes in fluoride free electrolytes

In the present work we report on the formation of bundles of high aspect ratio TiO₂ nanotubes and WO₃ nanopores structures with very thin tube or pore walls using anodization under “high voltage” conditions in perchlorate or chloride containing electrolytes. The bundles of TiO₂ nanotubes consist of separated tubes with diameters in the range of approximately 20–40 nm and the WO₃ nanopores consist of pores with diameters in the range of 30–50 nm. Growth occurs locally at specific surface locations. Both the TiO₂ and the WO₃ structures can be grown up to several dozens of micrometers in length within few minutes. We suggest that the growth of these high aspect structures is initiated by localized anodic breakdown event, triggered by a sufficiently high applied anodic field.