Synthesis and characterization of 2,2‐bis(methylol)propionic acid dendrimers with different cores and terminal groups

Three sets of aliphatic polyester dendrimers based on 2,2‐bis(methylol)propionic acid (bis‐MPA) were synthesized. Two of the sets had benzylidene terminal groups and either a trimethylolpropane or triphenolic core moiety. The last set had acetonide terminal groups and a triphenolic core moiety. Benzylidene‐[G#1]‐anhydride and acetonide‐[G#1]‐anhydride were used as the reactive building blocks in the construction of all dendrimers. The large excess of building blocks used in the coupling reactions initially resulted in considerable material loss. This waste was eliminated through the development of a recycling method. ¹H and ¹³C NMR and matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) analysis were used to verify the purity of all compounds. Size exclusion chromatography (SEC) was used, as well as MALDI‐TOF, for molecular weight determinations. The SEC measurements were conducted with a universal calibration method and an online right‐angle laser light scattering detector. Measured dendrimer molecular weights were close to their theoretical molar masses. Observations were also made of the hydrodynamic radius and intrinsic viscosity for the different dendrimers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1758–1767, 2004     

Thermal and X‐ray powder diffraction studies of aliphatic polyester dendrimers

The syntheses and thermal and X‐ray powder diffraction analyses of three sets of aliphatic polyester dendrimers based on 2,2‐bis(hydroxymethyl)propionic acid as a repeating unit and 2,2‐dimethyl‐1,3‐propanediol, 1,5‐pentanediol, and 1,1,1‐tris(hydroxymethyl)ethane as core molecules are reported. These dendritic polyesters were prepared in high yields with the divergent method. The thermal properties of these biodendrimers were evaluated with thermogravimetric analysis and differential scanning calorimetry. The thermal decomposition of the compounds occurred around 250 °C for the hydroxyl‐ended dendrimers and around 150 °C for the acetonide‐protected dendrimers. In addition, the crystallinity of the lower generation dendrimers was evaluated with X‐ray powder diffraction. The highest crystallinity and the highest melting points were observed for the first‐generation dendritic compounds. The higher generation dendrimers showed weaker melting transitions during the first heating scan. Only the glass‐transition temperatures were observed in subsequent heating scans. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5574–5586, 2004     

Preparation and characterization of fluorine‐containing aromatic condensation polymers. VII. Aromatic polyacetals and copolyacetals from 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane and/or 2,2‐bis(4‐hydroxyphenyl)propane and 2‐(trifluoromethyl)benzal chloride

A series of fluorine‐containing aromatic homopolyacetals and copolyacetals with a wide range of unit ratios were synthesized by the solution polycondensation of 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane (bisphenol AF), 2,2‐bis(4‐hydroxyphenyl)propane (bisphenol A), or both with 2‐(trifluoromethyl)benzal chloride, and the effect of fluorine substitution on the properties of these polymers is discussed in relation to the fluorine contents. High molecular weight polyacetals with reduced viscosities of 0.43–0.97 dL/g were obtained in high yields with potassium hydroxide as a base, 18‐crown 6‐ether as a catalyst, and N‐methyl‐2‐pyrrolidinone as a medium at 100 °C for 3 h. Regardless of the fluorine contents, these polymers all were highly soluble in various solvents, including benzene, chloroform, ethyl acetate, and tetrahydrofuran, and afforded colorless, transparent, and tough films by solution casting. The temperatures of 5% weight loss and 10% weight loss under nitrogen both increased significantly and monotonously with increasing fluorine content, whereas the glass‐transition temperatures were scarcely affected by fluorine substitution. The dielectric constant at 1 MHz of the bisphenol AF‐based homopolyacetal was 2.43, which was remarkably lower than the value of the bisphenol A‐based homopolyacetal, 2.68. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1873–1879, 2000     

Electrochemical Reduction of 4,4′‐(2,2,2‐Trichloroethane‐1,1‐diyl)‐ bis(chlorobenzene) (DDT) and 4,4′‐(2,2‐Dichloroethane‐1,1‐diyl)‐ bis(chlorobenzene) (DDD) at Carbon Cathodes in Dimethylformamide

In dimethylformamide containing tetramethylammonium tetrafluoroborate, cyclic voltammograms for reduction of 4,4′‐(2,2,2‐trichloroethane‐1,1‐diyl)bis(chlorobenzene) (DDT) at a glassy carbon cathode exhibit five waves, whereas three waves are observed for the reduction of 4,4′‐(2,2‐dichloroethane‐1,1‐diyl)bis(chlorobenzene) (DDD). Bulk electrolyses of DDT and DDD afford 4,4′‐(ethene‐1,1‐diyl)bis(chlorobenzene) (DDNU) as principal product (67–94%), together with 4,4′‐(2‐chloroethene‐1,1‐diyl)bis(chlorobenzene) (DDMU), 1‐chloro‐4‐styrylbenzene, and traces of both 1,1‐diphenylethane and 4,4′‐(ethane‐1,1‐diyl)bis(chlorobenzene) (DDO). For electrolyses of DDT and DDD, the coulometric n values are essentially 4 and 2, respectively. When DDT is reduced in the presence of a large excess of D₂O, the resulting DDNU and DDMU are almost fully deuterated, indicating that reductive cleavage of the carbon–chlorine bonds of DDT is a two‐electron process that involves carbanion intermediates. A mechanistic scheme is proposed to account for the formation of the various products.     

Kinetics of the polycondensation and copolycondensation of bis(3‐hydroxypropyl) terephthalate and bis(4‐hydroxybutyl) terephthalate

The kinetics of the polycondensation and copolycondensation reactions of bis(3‐hydroxypropyl) terephthalate (BHPT) and bis(4‐hydroxybutyl) terephthalate (BHBT) as monomers were investigated at 270 °C in the presence of titanium tetrabutoxide as a catalyst. BHPT was prepared by the ester interchange reaction of dimethyl terephthalate and 1,3‐propanediol (1,3‐PD). Through the same method adopted for BHPT synthesis, BHBT was prepared with 1,4‐butanediol instead of 1,3‐PD. With second‐order kinetics applied for polycondensation, the rate constants of the polycondensation of BHPT and BHBT, k₁₁ and k₂₂, were calculated to be 4.08 and 4.18 min^?1, respectively. The rate constants of the cross reactions in the copolycondensation of BHPT and BHBT, k₁₂ and k₂₁, were calculated with results obtained from proton nuclear magnetic resonance spectroscopy analysis. The rate constants during the copolycondensation of BHPT and BHBT at 270 °C decreased in the order k₁₂ > k₂₂ > k₁₁ > k₂₁, indicating that the reactivity of BHBT was larger than that of BHPT at 270 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2435–2441, 2002     

A MALDI‐TOF MS study of lanthanide(III)‐cored poly(phenylenevinylene) dendrimers

An extensive study by matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectrometry (MS) of some first‐generation and second‐generation lanthanide(III)‐cored poly(phenylenevinylene) dendrimers is described. The complexes were obtained by self‐assembly of suitably functionalized carboxylate dendrons around the lanthanide ion (La³⁺, Er³⁺). Fourier transform infrared (FT‐IR) spectroscopy gave reasonable evidence for the proposed structures. However, MS was used to ascertain unequivocally the complex formation. The most reliable results were found in the negative reflector mode, using 2‐[(2E)‐3‐(4‐tert‐butylphenyl)‐2‐methylprop‐2‐enylidene]malononitrile (DCTB) as matrix. Well‐defined and highly resolved base peaks corresponding to negative ions of [Gn₄La]^? and [Gn₄Er]^? were found in all cases, with an excellent match between the theoretical and observed isotope distributions. However, the 3 : 1 stoichiometry used in the synthesis guarantees an empirical formula Gn₃Ln for the complexes. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and properties of new aromatic poly‐(ether benzoxazole)s from 2,2′‐bis(4‐amino‐3‐hydroxyphenoxy)biphenyl and aromatic dicarboxylic acid chlorides

A new bis(o‐aminophenol) with a crank and twisted noncoplanar structure and ether linkages, 2,2′‐bis(4‐amino‐3‐hydroxyphenoxy)biphenyl, was synthesized by the reaction of 2‐benzyloxy‐4‐fluoronitrobenzene with biphenyl‐2,2′‐diol, followed by reduction. Biphenyl‐2,2′‐diyl‐containing aromatic poly(ether benzoxazole)s with inherent viscosities of 0.52–1.01 dL/g were obtained by a conventional two‐step procedure involving the polycondensation of the bis(o‐aminophenol) monomer with various aromatic dicarboxylic acid chlorides, yielding precursor poly(ether o‐hydroxyamide)s, and subsequent thermal cyclodehydration. These new aromatic poly(ether benzoxazole)s were soluble in methanesulfonic acid, and some of them dissolved in m‐cresol. The aromatic poly(ether benzoxazole)s had glass‐transition temperatures of 190–251 °C and were stable up to 380 °C in nitrogen, with 10% weight losses being recorded above 520 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2656–2662, 2002     

Synthesis and characterization of organosoluble copolyimides based on 2,2‐Bis[4‐(4‐aminophenoxy)phenyl]propane, 2,2‐Bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane and a pair of commercial aromatic dianhydrides

Organosoluble homopolyimides (PIs) and copolyimides (CoPIs) were synthesized from 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP) or 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane (6FBAPP) and six kinds of commercial aromatic dianhydrides (PMDA, II _a ; BTDA, II _b ; BPDA, II _c ; ODPA, II _d ; DSDA, II _e ; 6FDA, II _f ). Although BAPP and II _d∼f could prepare three kinds of soluble PIs ( III‐A _d∼f ), likewise 6FBAPP and II _c∼f could prepare four PIs ( III‐B _c∼f ), the insoluble PIs were synthesized from these two diamines and other dianhydrides. However, soluble CoPIs could be prepared by alternative copolycondensation from a pair of dianhydrides of soluble PIs and insoluble PIs in certain molar ratios (m₁/m₂). The ratios of m₁/m₂ of BAPP/PMDA series CoPIs ( IV _{m1(d–f)/m2a} ) ranged from 3–5, but ratios of 6FBAPP/PMDA series CoPIs ( V _{m1(c∼f)/m2a} ) decreased to 2–3. The m₁/m₂ of the BAPP/BTDA and 6FBAPP/BTDA series CoPIs were 2, while the BAPP/BPDA series were between 1–2. Composition, solubility, tensile properties and thermal properties of these CoPIs synthesized via a two‐stage thermal cyclodehydration were determined and were compared with their corresponding PIs. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3954–3961, 2000     

Synthesis and characterization of new soluble poly(amide‐imide)s derived from 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane

A series of new soluble poly(amide‐imide)s were prepared from the diimide‐dicarboxylic acid 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane with various diamines by direct polycondensation in N‐methyl‐2‐pyrrolidinone containing CaCl₂ with triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.52–0.86 dL · g^?1. The poly(amide‐imide)s showed an amorphous nature and were readily soluble in various solvents, such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, pyridine, and cyclohexanone. Tough and flexible films were obtained through casting from DMAc solutions. These polymer films had tensile strengths of 71–107 MPa and a tensile modulus range of 1.6–2.7 GPa. The glass‐transition temperatures of the polymers were determined by a differential scanning calorimetry method, and they ranged from 242 to 279 °C. These polymers were fairly stable up to a temperature around or above 400 °C, and they lost 10% of their weight from 480 to 536 °C and 486 to 537 °C in nitrogen and air, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3498–3504, 2001     

A three‐dimensional ZnII coordination framework: poly[[μ2‐(E)‐1,2‐bis(pyridin‐4‐yl)ethene][μ4‐(E)‐2,2′‐(diazene‐1,2‐diyl)dibenzoato][μ2‐(E)‐2,2′‐(diazene‐1,2‐diyl)dibenzoato]dizinc(II)]

In the title coordination polymer, [Zn₂(C₁₄H₈N₂O₄)₂(C₁₂H₁₀N₂)]_n, the asymmetric unit contains one Zn^II cation, two halves of 2,2′‐(diazene‐1,2‐diyl)dibenzoate anions (denoted L²⁻) and half of a 1,2‐bis(pyridin‐4‐yl)ethene ligand (denoted bpe). The three ligands lie across crystallographic inversion centres. Each Zn^II centre is four‐coordinated by three O atoms of bridging carboxylate groups from three L²⁻ ligands and by one N atom from a bpe ligand, forming a tetrahedral coordination geometry. Two Zn^II atoms are bridged by two carboxylate groups of L²⁻ ligands, generating a [Zn₂(CO₂)₂] ring. Each loop serves as a fourfold node, which links its four equivalent nodes via the sharing of four L²⁻ ligands to form a two‐dimensional [Zn₂L₄]_n net. These nets are separated by bpe ligands acting as spacers, producing a three‐dimensional framework with a 4⁶6⁴ topology. Powder X‐ray diffraction and solid‐state photoluminescence were also measured.     

Chemical modification of polyamide‐6 by chain extension with 2,2′‐bis(2‐oxazoline)

The chain‐extension behavior of 2,2′‐bis(2‐oxazoline) (BOZ) was studied to evaluate the coupling effect on polyamide‐6 (PA6) in a Haake Rheocord mixer and an extruder. The relative torque of PA6 dramatically increased within 1–2 min, and the results were similar whether the added amount of BOZ in PA6 was the theoretical amount or twice as much at 240 °C; however, after 5 min, the coupling results showed an optimal dosage of the chain extender, a lack of which caused a deficiency of chain extension and an excess of which led to a greater blocking reaction. The final torque was 2.16 times as much as that of a control sample when the reaction temperature was 240 °C, and the added amount of BOZ in PA6 was 1.156%; at the same time, the initial carboxyl content of the chain‐extended products decreased to 40% for PA6, and this corresponded to the intrinsic viscosity of PA6 increasing to 1.636 dL/g, whereas that of the control sample was 1.384 dL/g. Furthermore, the effects of BOZ on the thermal and mechanical properties of chain‐extended PA6 were investigated. The degree of crystallinity decreased as the chain extender was added to PA6. The Izod impact strength, tensile strength, and elongation at break of the resultant products dramatically improved under wet conditions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1976–1982, 2007     

Synthesis and properties of new polyarylates from 1,4‐bis(4‐carboxyphenoxy)naphthyl or 2,6‐bis(4‐carboxyphenoxy)naphthyl and various bisphenols

New 1,4‐naphthyl and 2,6‐naphthyl‐containing polyarylates having inherent viscosities up to 1.28 dL/g were synthesized by the high‐temperature solution polycondensation from the acid chloride of 1,4‐bis(4‐carboxyphenoxy)naphthyl or 2,6‐bis(4‐carboxyphenoxy)naphthyl and various bisphenols. Most of the resulting polyarylates showed amorphous characteristics and were readily soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), o‐chlorophenol, and chloroform. Transparent, flexible, and colorless films of these polymers could be cast from the DMAc solutions. Their cast films had tensile strengths ranging from 54.9 to 84.2 MPa, elongations at break from 5.3% to 19.0%, and initial modulus from 2.0 to 2.8 GPa. These polymers had glass transition temperatures in the range of 172–280°C and began to lose weight around 400°C, with 10% weight loss being recorded at about 450°C in air. Dynamic mechanical analysis (DMA) reveals that the polyarylates containing isopropylidene linkages have three transitions on the temperature scale between −100 and 300°C. However, only two transitions were observed in the other polyarylates without isoproylidene linkage. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 645–652, 1999     

Synthesis,characterization, and in vitro degradation of thermotropic polyesters and copolyesters based on terephthalic acid, 3‐(4‐hydroxyphenyl)propionic acid,and glycols

A new series of thermotropic liquid‐crystalline (LC) polyesters were prepared from a diacyl chloride derivative of 4,4′‐(terephthaloyldioxy)‐di‐4‐phenylpropionic acid (PTP) and glycols with a different number of methylene groups (n) [HO(CH₂)_n OH, n = 6–10, 12] by high‐temperature solution polycondensation in diphenyl oxide. PTP6/10 and PTP6/hydroquinone (H) LC copolyesters were also prepared according to a similar procedure. The chemical structure, LC, phase‐transition behaviors, thermal stability, and solubility were characterized by elemental analysis, Fourier transform infrared spectroscopy, ¹H and ¹³C NMR spectra, differential scanning calorimetry (DSC), thermogravimetric analysis, and a polarizing light microscope. The melting and isotropization temperatures decreased in a zigzag manner as the number of n increased. All of the polyesters formed a nematic phase with the exception of PTP8. The temperature ranges of the mesophase (ΔT) were much wider for the polyesters with an odd number of n's than those with an even number. ΔT increased markedly for the PTP6/10 and PTP6/H copolyesters. The in vitro degradations of the polymers were ascertained by enzymatic hydrolysis and alkaline hydrolysis. The model compound, PTP dihexylester, was synthesized and found to be degraded into terephthalic acid, 3‐(4‐hydroxyphenyl)propionic acid, and 1‐hexanol by Rhizopus delemar lipase, but PTPn homopolyesters and PTP6/10 and PTP6/H copolyesters were resistant to Rhizopus delemar hydrolysis. They were degradable in a sodium hydroxide buffer solution of pH 12 at 60 °C, depending on the number of n's and the copolymer composition. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3043–3051, 2001     

Two new cadmium(II) coordination polymers based on bis(1,2,4‐triazol‐1‐yl)alkane ligands and pyrazine‐2,3‐dicarboxylic acid

Assemblies of pyrazine‐2,3‐dicarboxylic acid and Cd^II in the presence of bis(1,2,4‐triazol‐1‐yl)butane or bis(1,2,4‐triazol‐1‐yl)ethane under ambient conditions yielded two new coordination polymers, namely poly[[tetraaqua[μ₂‐1,4‐bis(1,2,4‐triazol‐1‐yl)butane‐κ²N⁴:N^4′]bis(μ₂‐pyrazine‐2,3‐dicarboxylato‐κ³N¹,O²:O³)dicadmium(II)] dihydrate], {[Cd₂(C₆H₂N₂O₄)₂(C₈H₁₂N₆)(H₂O)₄]·2H₂O}_n, (I), and poly[[diaqua[μ₂‐1,2‐bis(1,2,4‐triazol‐1‐yl)ethane‐κ²N⁴:N^4′]bis(μ₃‐pyrazine‐2,3‐dicarboxylato‐κ⁴N¹,O²:O³:O^3′)dicadmium(II)] dihydrate], {[Cd₂(C₆H₂N₂O₄)₂(C₆H₈N₆)(H₂O)₂]·2H₂O}_n, (II). Complex (I) displays an interesting two‐dimensional wave‐like structure and forms a distinct extended three‐dimensional supramolecular structure with the help of O—H...N and O—H...O hydrogen bonds. Complex (II) has a three‐dimensional framework structure in which hydrogen bonds of the O—H...N and O—H...O types are found.     

Synthesis and properties of new polyamides derived from 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone by direct polycondensation

A series of new polyamides containing both sulfone and oxyethylene moieties in the polymer chain was prepared by the direct polycondensation of the diamine monomer 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone (BAEPS) and various aromatic dicarboxylic acids in N‐methyl‐2‐pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with inherent viscosities of 0.30–0.60 dl/g and identified by elemental analysis, and infrared and nuclear magnetic resonance spectra. Most of the polymers were readily dissolved in polar solvents such as NMP, dimethylsulfoxide, N,N‐dimethylacetamide, N,N‐dimethylformamide and m‐cresol at room temperature. Polymers containing rigid and symmetric p‐phenylene, naphthalene and p‐biphenylene moieties revealed a crystalline nature and showed no solubility in organic solvents. These polyamides had 10% weight loss temperatures ranging between 423 and 465 °C in nitrogen atmosphere and glass transition temperatures between 170 and 305 °C. The polymers with crystallinity nature exhibited melting endotherms (T_m) below 386 °C in differential scanning calorimetry trace. Copyright © 1999 John Wiley & Sons, Ltd.     

Two complexes of PtIV and AuIII with 2,2′‐dipyridylamine and 2,2′‐dipyridylaminide ligands

Two noble metal complexes involving ancillary chloride ligands and chelating 2,2′‐bipyridylamine (Hdpa) or its deprotonated derivative (dpa), namely [bis(pyridin‐2‐yl‐κN)amine]tetrachloridoplatinum(IV), [PtCl₄(C₁₀H₉N₃)], and [bis(pyridin‐2‐yl‐κN)aminido]dichloridogold(III), [AuCl₂(C₁₀H₈N₃)], are presented and structurally characterized. The metal atom in the former has a slightly distorted octahedral coordination environment, formed by four chloride ligands and two pyridyl N atoms of Hdpa, while the metal atom in the latter has a slightly distorted square‐planar coordination environment, formed by two chloride ligands and two pyridyl N atoms of dpa. The difference in conjugation between the pyridine rings in normal and deprotonated 2,2′‐dipyridylamine is discussed on the basis of the structural features of these complexes. The influence of weak interactions on the supramolecular structures of the complexes, providing one‐dimensional chains of [PtCl₄(C₁₀H₉N₃)] and dimers of [AuCl₂(C₁₀H₈N₃)], are discussed.     

Gas‐phase geometries and energies of bis(2,2′‐bipyridine) interacting either with Cu(I) or Ag(I): Computational study

With a polarized double‐zeta basis set, we carried out MP2 and density functional theory geometry optimization of bis(2,2′‐bipyridine) interacting either with Cu(I) or Ag(I). The computed gas‐phase geometries of both Cu and Ag complexes present tetrahedral distortions around the ions. However, geometry optimization on Cu or Ag ions complexing with ammonia molecules yield perfect tetrahedral coordination and interaction energies comparable to those of the bis(2,2′‐bipyridine) complexes. Solid‐state laboratory studies on complexes of the same metal ions with substituted bis(2,2′‐bipyridine) revealed tetrahedral distortions around the ions, even stronger than those computed in the gas phase. From our analysis of the potential interaction energies we conclude that the origin of the larger distortions in the solid state result from stacking interactions. © 2003 Wiley Periodicals, Inc. Int J Quantum Chem 93: 395–404, 2003     

Synthesis and properties of ortho‐linked aromatic polyimides based on 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene

A bis(ether amine) containing the ortho‐substituted phenylene unit and pendant tert‐butyl group, 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene, was synthesized and used as a monomer to prepare polyimides with six commercial dianhydrides via a conventional two‐stage procedure. The intermediate poly(amic acid)s had inherent viscosities of 0.78–1.44 dL/g, and most of them could be thermally converted into transparent, flexible, and tough polyimide films. The inherent viscosities of the resulting polyimides were in the range of 0.46–0.87 dL/g. All polyimides were noncrystalline, and most of them showed excellent solubility in polar organic solvents. The glass‐transition temperatures of these polyimides were in the range of 222–259 °C in differential scanning calorimetry and 212–282 °C in thermomechanicl analysis. These polyimides showed no appreciable decomposition up to 500 °C in thermogravimetric analysis in air or nitrogen. A comparative study of the properties with the corresponding polyimides without pendant tert‐butyl groups derived from 1,2‐bis(4‐aminophenoxy)benzene is also presented. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1551–1559, 2000     

Synthesis of poly(ester‐amide) dendrimers based on 2,2‐Bis(hydroxymethyl) propanoic acid and glycine

Water‐soluble, biodegradable, and biocompatible poly(ester‐amide) dendrimers with hydroxyl functional groups are synthesized from previously prepared AB₂ adduct of 2,2‐bis(hydroxymethyl) propanoic acid (bis‐MPA) and glycine as a repeating unit. Two esterification procedures using different coupling reagent/catalyst systems (DCC/DPTS or EDC/DMAP) are studied with respect to efficiency, ease of products purification, and quality of the final products. Both procedures have their own benefits and drawbacks, depending on dendrimer generation. The synthesized poly(ester‐amide) dendrimers as well as commercially available bis‐MPA dendrimers, poly(ester‐amide) hyperbranched polymer, and poly(vinyl alcohol) are used for preparation of solid dispersions of sulfonylurea antidiabetic drug glimepiride to improve its poor water‐solubility. In vitro dissolution studies show in comparison with pure glimepiride in crystalline or amorphous form, to the same extent improved glimepiride solubility for solid dispersions based on dendritic polymers, but not for poly(vinyl alcohol). The amount of glimepiride complexed with both dendrimer types increases with dendrimer generation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3292–3301     

Impact of Reaction Conditions on the Structures of Nickel(II) Complexes Based on 3‐(4‐Carboxyphenyl)propionic Acid

Two new nickel(II) complexes, [Ni(4, 4′‐bpy)(H₂O)₄]_n · n(cpp) · 0.5nH₂O ( 1 ) and [Ni(cpp)(4, 4′‐bpy)(H₂O)₂]_n ( 2 ) [4, 4′‐bpy = 4, 4′‐bipyridine, H₂cpp = 3‐(4‐carboxyphenyl)propionic acid] were synthesized and characterized by single‐crystal X‐ray diffraction, elemental analysis, IR spectroscopy, and thermal analysis. In complex 1 , Ni^II ions are bridged by 4, 4′‐bpy into 1D chains, and cpp ligands are not involved in the coordination, whereas in complex 2 , cpp ligands adopt a bis(monodentate) mode and link Ni^II ions into 2D (4, 4) grids with the help of 4, 4′‐bpy ligands. Triple interpenetration occurs, which results in the formation of a complicated 3D network. The difference in the structures of the two complexes can be attributed to the different reaction temperatures and bases.