Atom transfer radical polymerization of functional monomers employing Cu‐based catalysts at low concentration: Polymerization of glycidyl methacrylate

Initiators for continuous activator regeneration atom transfer radical polymerization (ICAR ATRP) of an epoxide‐containing monomer, glycidyl methacrylate (GMA), was successfully carried out using low concentration of catalyst (ca. 105 ppm) at 60 °C in anisole. The copper complex of tris(2‐pyridylmethyl)amine was used as the catalyst, diethyl 2‐bromo‐2‐methylmalonate as the initiator, and 2,2′‐azobisisobutyronitrile as the reducing agent. When moderate degrees of polymerization were targeted (up to 200), special purification of the monomer, other than removal of the polymerization inhibitor, was not required to achieve good control. To synthesize well‐defined polymers with higher degrees of polymerization (600), it was essential to use very pure monomer, and polymers of molecular weights exceeding 50,000 g mol^?1 and M_w/M_n = 1.10 were prepared. The developed procedures were used to chain‐extend bromine‐terminated poly(methyl methacrylate) macroinitiator prepared by activators regenerated by electron transfer (ARGET) ATRP. The Sn^II‐mediated ARGET ATRP technique was not suitable for the polymerization of GMA and resulted in polymers with multimodal molecular weight distributions. This was due to the occurrence of epoxide ring‐opening reactions, catalyzed by Sn^II and Sn^IV. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Solvent effect on the atom transfer radical polymerization of allyl methacrylate

The controlled radical polymerization of allyl methacrylate by atom transfer radical polymerization was carried out in solution at 70 °C, with ethyl 2‐bromoisobutyrate as the initiator and copper halide (CuX, where X is Cl or Br) with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Kinetic analyses demonstrated that all the homopolymerization reactions showed a general behavior characterized by two clearly differentiated stages. Thus, in the early stage, the conversion increased continually with the time, independently of the solvent employed. In the second stage, a deceleration process took place, and a limit conversion was achieved, depending on the polarity and amount of the solvent used. The dependence of both the gel formation and limit conversion, as well as the molecular characteristics of poly(allyl methacrylate)s formed with different experimental parameters, such as the initial monomer concentration, the solvent employed, and the type of halide used as a catalyst, was also examined. The prepared polymers were characterized by size exclusion chromatography, Fourier transform infrared, and one‐ and two‐dimensional nuclear magnetic resonance spectroscopy. Moreover, chain‐growth experiments with butyl acrylate as the comonomer proved the living character of the poly(allyl methacrylate)s obtained, with these used as macroinitiators. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6247–6261, 2005     

Atom transfer radical polymerization of 1-phenoxycarbonyl ethyl methacrylate monomer

Atom transfer radical polymerization conditions with copper(I) bromide/2,2^′-bipyridine (Cu/2,2^′-bpy) as the catalyst system were employed for the homopolymerization and random copolymerization of 1-phenoxycarbonyl ethyl methacrylate (PCMA) with methyl methacrylate (MMA). Temperature studies indicated that the polymerizations occurred smoothly in bulk at 110 °C. Poly(PCMA)(polydispersity index=1.27) homopolymer was characterized and then used as macroinitiator for increasing its molecular weight. The homopolymerization of PCMA was also carried out under free radical conditions using 2,2^′-azobisisobutyronitrile as an initiator.The monomer and polymers were characterized by FT-IR and ¹H and ¹³C-NMR techniques. The glass transition temperatures, the solubility parameters and average-molecular weights of the polymers were determined. Thermal stabilities of the polymers were given as compared with each other by using TGA curves. Thermal degradation products of poly(PCMA)s obtained by ATRP and free radical polymerization were compared with each other by using ¹H-NMR technique.     

Atom transfer radical polymerization of sodium2‐acrylamido‐2‐methylpropanesulfonate

The first example of well‐controlled atom transfer radical polymerization (ATRP) of a permanently charged anionic acrylamide monomer is reported. ATRP of sodium 2‐acrylamido‐2‐methylpropanesulfonate (NaAMPS) was achieved with ethyl 2‐chloropropionate (ECP) as an initiator and the CuCl/CuCl₂/tris(2‐dimethylaminoethyl)amine (Me₆TREN) catalytic system. The polymerizations were carried out in 50:50 (v/v) N,N‐dimethylformamide (DMF)/water mixtures at 20 °C. Linear first‐order kinetic plots up to a 92% conversion for a target degree of polymerization of 50 were obtained with [ECP]/[CuCl]/[CuCl₂]/[Me₆TREN] = 1:1:1:2 and [AMPS] = 1 M. The molecular weight increased linearly with the conversion in good agreement with the theoretical values, and the polydispersities decreased with increasing conversion, reaching a lower limit of 1.11. The living character of the polymerization was confirmed by chain‐extension experiments. Block copolymers with N,N‐dimethylacrylamide and N‐isopropylacrylamide were also prepared. The use of a DMF/water mixed solvent should make possible the synthesis of new amphiphilic ionic block copolymers without the use of protecting group chemistry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4446–4454, 2005     

Atom transfer radical polymerization of methyl methacrylate at ambient temperature using soluble Cu(I) complex catalysts formed with mixed ligands of multidentate amines and halide ions

An Erratum has been published for this article in J Polym Sci Part A: Polym Chem (2004) 42(19) 5030 . The addition of soluble quaternaryammonium halides (QX) in catalytic amounts takes into solution CuX/pentamethyldiethylenetriamine (PMDETA) complex (X = Cl, Br) in methyl methacrylate (MMA). The soluble catalyst complex provided much better control of the polymerization of MMA at ambient temperature than did the insoluble catalyst formed in the absence of QX, with CuCl/PMDETA/Aliquat® 336 (AQCl) proving to be superior to the CuBr/PMDETA/Bu₄NBr catalyst system. The effect was independent of the size of the quaternaryammonium ion. Also, the presence of Cl in the catalyst–QX combination either as CuCl or as QCl was enough to give much better control than that provided by a wholly Br‐based system. Among the various initiators used, that is, ethyl 2‐bromoisobutyrate (EBiB), methyl 2‐bromopropionate (MBP), 1‐phenylethyl bromide (PEBr), and p‐toluenesulfonyl chloride (pTsCl), only EBiB gave a satisfactory result. With MBP and PEBr the initiation was slower than the propagation, whereas with pTsCl the initiation was very fast, so that instantaneous termination occurred. The living nature of the polymers was shown by block copolymer preparation. It has been suggested that some of the added halide ions entered into the coordination spheres of Cu(I) and Cu(II), leading to their improved solubility and stronger deactivation by the Cu(II) complex. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4132–4142, 2004     

Ambient‐temperature copper‐catalyzed atom transfer radical polymerization of methacrylates in ethylene glycol solvents

The use of ethylene glycol solvents in the room‐temperature atom transfer radical polymerization (ATRP) of various hydrophobic and hydrophilic methacrylates is demonstrated. Unlike many of the very polar solvents described in the literature for room‐temperature ATRP, these solvents have good solvency for a wide range of polymers and monomers and are cheap and relatively nontoxic. Ethylene glycols with one hydroxyl and one methoxy group, such as tri(ethylene glycol) monomethyl ether (TEGMME), provide optimal results. The polymerization of methyl methacrylate in TEGMME with CuBr/N,N,N′N′,N″‐pentamethyldiethylenetriamine as the catalyst requires the addition of CuCl₂ at the beginning of the reaction to produce well‐controlled polymerizations. This leads to polymers with predictable molecular weights and relatively narrow polydispersities. Polymerization in solvents that are fully methoxy‐capped terminate prematurely because of catalyst precipitation. The electrochemical behavior of copper complexes in selected solvents is examined to determine why these solvents provide good rates at room temperature. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1588–1598, 2005     

Reverse atom transfer radical polymerization of methyl methacrylate in room‐temperature ionic liquids

The reverse atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully carried out in 1‐butyl‐3‐methylimidazolium hexafluorophosphate with 2,2′‐azobisisobutyronitrile/CuCl₂/bipyridine as the initiating system, which had been reported as not able to promote a controlled process of MMA in bulk. The living nature of the polymerization was confirmed by kinetic studies, end‐group analysis, chain extension, and block copolymerization results. The polydispersity of the polymer obtained was quite narrow, with a weight‐average molecular weight/number‐average molecular weight ratio of less than 1.2. In comparison with other reverse ATRPs in bulk or conventional solvents, a much smaller amount of the catalyst was used. After a relatively easy removal of the polymer and residue monomer, the ionic liquid and catalytic system could be reused without further treatment. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 143–151, 2003     

Synthesis of poly(methyl methacrylate) in a pyridine solution by atom transfer radical polymerization

Pyridine was used as a solvent for the atom transfer radical polymerization (ATRP) of methyl methacrylate. The homopolymerizations were carried out with methyl 2‐halopropionate (MeXPr, where X was Cl or Br) as an initiator, copper halide (CuX) as a catalyst, and 2,2′‐bipyridine as a ligand from 80 to 120 °C. The mixed halogen system methyl 2‐bromopropionate/copper chloride was also used. For all the initiator systems used, the polymerization reaction showed linear first‐order rate plots, a linear increase in the number‐average molecular weight with conversion, and relatively low polydispersities. In addition, the dependence of the polymerization rate on the temperature is presented. These data are compared with those obtained in bulk, demonstrating the effectiveness of this solvent for this monomer in ATRP. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3443–3450, 2001     

Atom transfer radical polymerization of N‐vinyl carbazole: Optimization to characterization

The homopolymerization of N‐vinylcarbazole was performed with atom transfer radical polymerization (ATRP) with Cu(I)/Cu(II)/2,2′‐bipyridine (bpy) as the catalyst system at 90 °C in toluene. N‐2‐Bromoethyl carbazole was used as the initiator, and the optimized ratio of Cu(I) to Cu(II) was found to be 1/0.3. The resulting homopolymer, poly(N‐vinylcarbazole) (PVK), was formed after a monomer conversion of 76% in 20 h. The molecular weight as well as the polydispersity index (PDI) showed a linear relation with the conversion, which showed control over the polymerization. A semilogarithmic plot of the monomer conversion with time was linear, indicating the presence of constant active species throughout the polymerization. The initiator efficiency and the effect of the variation of the initiator concentration on the polymerization were studied. The effects of the addition of CuBr₂, the variation of the catalyst concentration with respect to the initiator, and CuX (X = Br or Cl) on the kinetics of homopolymerization were determined. With Cu(0)/CuBr₂/bpy as the catalyst, faster polymerization was observed. For a chain‐extension experiments, PVK (number‐average molecular weight = 1900; PDI = 1.24) was used as a macroinitiator for the ATRP of methyl methacrylate, and this resulted in the formation of a block copolymer that gave a monomodal curve in gel permeation chromatography. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1745–1757, 2006     

Synthesis and characterization of sulfonated block copolymers by atom transfer radical polymerization

Well‐defined sulfonated polystyrene and block copolymers with n‐butyl acrylate (nBA) were synthesized by CuBr catalyzed living radical polymerization. Neopentyl p‐styrene sulfonate (NSS) was polymerized with ethyl‐2‐bromopropionate initiator and CuBr catalyst with N,N,N′,N′‐pentamethylethyleneamine to give poly(NSS) (PNSS) with a narrow molecular weight distribution (MWD < 1.12). PNSS was then acidified by thermolysis resulting in a polystyrene backbone with 100% sulfonic acid groups. Random copolymers of NSS and styrene with various composition ratios were also synthesized by copolymerization of NSS and styrene with different feed ratios (MWD < 1.11). Well defined block copolymers with nBA were synthesized by sequential polymerization of NSS from a poly(n‐butyl acrylate) (PnBA) precursor using CuBr catalyzed living radical polymerization (MWD < 1.29). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5991–5998, 2008     

Synthesis of diblock copolymers by combining stable free radical polymerization and atom transfer radical polymerization

A stable nitroxyl radical functionalized with an initiating group for atom transfer radical polymerization (ATRP), 4‐(2‐bromo‐2‐methylpropionyloxy)‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy (Br‐TEMPO), was synthesized by the reaction of 4‐hydroxyl‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy with 2‐bromo‐2‐methylpropionyl bromide. Stable free radical polymerization of styrene was then carried out using a conventional thermal initiator, dibenzoyl peroxide, along with Br‐TEMPO. The obtained polystyrene had an active bromine atom for ATRP at the ω‐end of the chain and was used as the macroinitiator for ATRP of methyl acrylate and ethyl acrylate to prepare block copolymers. The molecular weights of the resulting block copolymers at different monomer conversions shifted to higher molecular weights and increased with monomer conversion. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2468–2475, 2006     

Synthesis of coil‐comb block copolymers containing polystyrene coil and poly(methyl methacrylate) side chains via atom transfer radical polymerization

A series of polystyrene‐b‐(poly(2‐(2‐bromopropionyloxy) styrene)‐g‐poly(methyl methacrylate)) (PS‐b‐(PBPS‐g‐PMMA)) and polystyrene‐b‐(poly(2‐(2‐bromopropionyloxy)ethyl acrylate)‐g‐poly(methyl methacrylate)) (PS‐b‐(PBPEA‐g‐PMMA)) as new coil‐comb block copolymers (CCBCPs) were synthesized by atom transfer radical polymerization (ATRP). The linear diblock copolymer polystyrene‐b‐poly(4‐acetoxystyrene) and polystyrene‐b‐poly(2‐(trimethylsilyloxy)ethyl acrylate) PS‐b‐P(HEA‐TMS) were obtained by combining ATRP and activators regenerated by electron transfer (ARGET) ATRP. Secondary bromide‐initiating sites for ATRP were introduced by liberation of hydroxyl groups via deprotection and subsequent esterification reaction with 2‐bromopropionyl bromide. Grafting of PMMA onto either the PBPS block or the PBPEA block via ATRP yielded the desired PS‐b‐(PBPS‐g‐PMMA) or PS‐b‐(PBPEA‐g‐PMMA). ¹H nuclear magnetic resonance spectroscopy and gel permeation chromatography data indicated the target CCBCPs were successfully synthesized. Preliminary investigation on selected CCBCPs suggests that they can form ordered nanostructures via microphase separation. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2971–2983     

Preparation of polyethylene block copolymers by a combination of postmetallocene catalysis of ethylene polymerization and atom transfer radical polymerization

The synthesis of block copolymers consisting of a polyethylene segment and either a poly(meth)acrylate or polystyrene segment was accomplished through the combination of postmetallocene-mediated ethylene polymerization and subsequent atom transfer radical polymerization. A vinyl-terminated polyethylene (number-average molecular weight = 1800, weight-average molecular weight/number-average molecular weight =1.70) was synthesized by the polymerization of ethylene with a phenoxyimine zirconium complex as a catalyst activated with methylalumoxane (MAO). This polyethylene was efficiently converted into an atom transfer radical polymerization macroinitiator by the addition of α-bromoisobutyric acid to the vinyl chain end, and the polyethylene macroinitiator was used for the atom transfer radical polymerization of n-butyl acrylate, methyl methacrylate, or styrene; this resulted in defined polyethylene-b-poly(n-butyl acrylate), polyethylene-b-poly(methyl methacrylate), and polyethylene-b-polystyrene block copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 496–504, 2004     

Atom transfer radical polymerization of acrylates in an ionic liquid: Synthesis of block copolymers

Atom transfer radical polymerization (ATRP) of acrylates in ionic liquid, 1‐butyl‐3‐methylimidazolium hexaflurophospate, with the CuBr/CuBr₂/amine catalytic system was investigated. Sequential polymerization was performed by synthesizing AB block copolymers. Polymerization of butyl acrylate (monomer that is only partly soluble in an ionic liquid forming a two‐phase system) proceeded to practically quantitative conversion. If the second monomer (methyl acrylate) is added at this stage, polymerization proceeds, and block copolymer formed is essentially free of homopolymer according to size exclusion chromatographic analysis. The number‐average molecular weight of the copolymer is slightly higher than calculated, but the molecular weight distribution is low (M_w/M_n = 1.12). If, however, methyl acrylate (monomer that is soluble in an ionic liquid) is polymerized at the first stage, then butyl acrylate in the second‐stage situation is different. Block copolymer free of homopolymer of the first block (with M_w/M_n = 1.13) may be obtained only if the conversion of methyl acrylate at the stage when second monomer is added is not higher than 70%. Matrix‐assisted laser desorption/ionization time‐of‐flight analysis confirmed that irreversible deactivation of growing macromolecules is significant for methyl acrylate polymerization at a monomer conversion above 70%, whereas it is still not significant for butyl acrylate even at practically quantitative conversion. These results show that ATRP of butyl acrylate in ionic liquid followed by addition of a second acrylate monomer allows the clean synthesis of block copolymers by one‐pot sequential polymerization even if the first stage is carried out to complete conversion of butyl acrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2799–2809, 2002     

Peptide block copolymers by N‐carboxyanhydride ring‐opening polymerization and atom transfer radical polymerization: The effect of amide macroinitiators

The synthesis of polypeptide‐containing block copolymers combining N‐carboxyanhydride (NCA) ring‐opening polymerization and atom transfer radical polymerization (ATRP) was investigated. An amide initiator comprising an amine function for the NCA polymerization and an activated bromide for ATRP was used. Well‐defined polypeptide macroinitiators were obtained from γ‐benzyl‐L ‐glutamate NCA, O‐benzyl‐serine NCA, and N‐benzyloxy‐L ‐lysine. Subsequent ATRP macroinitiation from the polypeptides resulted in higher than expected molecular weights. Analysis of the reaction products and model reactions confirmed that this is due to the high frequency of termination reactions by disproportionation in the initial phase of the ATRP, which is inherent in the amide initiator structure. In some cases selective precipitation could be applied to remove unreacted macroinitiator to yield well‐defined block copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Synthesis of semifluorinated block copolymers by atom transfer radical polymerization

Two sets of styrene‐based semifluorinated block copolymers, one with a perfluoroether pendant group and another with a perfluoroalkyl group, were synthesized by atom transfer radical polymerization. Microphase separation of the block copolymers was established by small‐angle X‐ray scattering and differential scanning calorimetry (DSC). DSC measurements also showed that the perfluoroether‐based polymer had a low glass‐transition temperature (?44 °C). Contact‐angle measurements indicated that the semifluorinated block copolymers had low surface energies (ca. 13 mJ/m²). These materials hold promise as low‐surface‐energy additives or surfactants for supercritical CO₂ applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 853–861, 2004     

Controlled radical polymerization of tert‐butyl acrylate at ambient temperature: Effect of initiator structure and synthesis of amphiphilic block copolymers

Controlled and very rapid ambient temperature polymerization of tert‐butyl acrylate (tBA) via atom transfer radical polymerization (ATRP) and single electron transfer living radical polymerization (SET‐LRP) conditions is reported. Two initiators, one that would generate a secondary radical and another that would generate a primary radical, upon activation, are used. A very active catalyst CuBr/Me₆TREN was found to initiate rapid polymerization whether it was the primary or the secondary initiator. The polymerization was well controlled and very rapid. The initiator that produces secondary initiating site is found to result in more rapid polymerization than the one that produces primary initiating site. To explore the possibility of rapid ambient temperature polymerization through the SET‐LRP mechanism, the polymerization was also carried out in the presence of DMSO. It was found that the polymerization was much faster compared to the bulk ATRP, without loss of control. Styrene was block copolymerized from PtBA macroinitiators and vice versa. In both the cases, block copolymers with controlled molecular weights were obtained. The tBA block of the polymer was selectively hydrolyzed to get amphiphilic block copolymers. This amphiphilic block copolymer was found to be useful in preparing stable cadmium sulfide (CdS) nanoparticulate dispersion. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Very rapid copper‐mediated atom transfer radical polymerization of benzyl methacrylate at ambient temperature

The ability to do very rapid bulk atom transfer radical polymerization (ATRP) of benzyl methacrylate using a CuX/PMDETA complex at room temperature was demonstrated in this study. The experimental conditions required to synthesize low‐ and high‐molecular‐weight poly(benzyl methacrylate) with low polydispersity are reported here. The controlled/living nature of the polymerization was demonstrated through kinetic studies, and chain‐extension studies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1053–1057, 2004     

Atom transfer radical polymerization from cellulose fibers at ambient temperature

Cellulose fibers have been successfully grafted with poly(methyl acrylate) using atom transfer radical polymerization, mediated by Me6-TREN and Cu(I)Br at ambient temperature. The initially hydrophilic cellulose was first modified by reacting the hydrozyl groups with 2-bromoisobutyryl bromide whereupon methyl acrylate was grafted from the surface. The resulting polymer-grafted papers were extremely hydrophobic, thetaa = 133 degrees . FT-IR analysis indicates that the amount of grafted polymer can be controlled by adding sacrificial initiator to the polymerizing system. Size exclusion chromatography of the bulk polymer revealed narrow polydispersities and a molecular weight corresponding to the ratio [M]:[I].