Studies on dynamic mechanical and mechanical properties of vinyloxyaminosilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM-g-VOS/LLDPE) blends

The dynamic mechanical properties of vinyloxyaminosilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM-g-VOS/LLDPE) blends have been evaluated with special reference to the effect of blend ratio. It has been found that increasing the proportion of LLDPE in the blends decreases the T_g values and increases the storage modulus (E^′) and loss modulus (E^′′) due to increase in crystallinity. A gradual increase in the values of tanδ_max is observed for the blends with increase in EPDM-g-VOS concentration, which indicates that no phase inversion occurs. But however the higher increase in tanδ_max after 50 wt.% of EPDM-g-VOS composition is due to small change in crystallinity and is ascertained by SEM micrographs. Mechanical properties such as tensile strength, Young’s modulus and hardness increase with increases in LLDPE concentration in the blends and with dicumyl peroxide (DCP) concentration whereas the values of elongation at break are decreased with increase in LLDPE and DCP concentration.     

Preparation and characterization of glass fiber–reinforced polyethylene terephthalate/linear low density polyethylene (GF‐PET/LLDPE) composites

Polyethylene terephthalate (PET) was melt blended with linear low density polyethylene (LLDPE) and subsequently compounded with glass fibers (GF) as reinforcements at percentages ranging from 15 to 45 wt% of LLDPE and 5 to 30 wt% of GF. Thermal, morphological, and mechanical properties of the prepared composites were investigated. It was found that compounding PET/LLDPE blends with GF would be beneficial in producing composites that are thermally stable with good mechanical properties. For example, the impact strength of the composites containing 85/15 wt% (PET/LLDPE) at relatively high loading of GF, ie, from 15 to 30 wt%, was higher than that of the GF‐reinforced neat PET. When increasing the percentage of LLDPE in the composites, the impact strength increased with increasing GF content, and this was also better than that of GF‐reinforced PET whose impact strength drastically decreased upon increasing the GF%. The improvement in mechanical properties of the composite, we suggest, should be correlated with the morphologies of the composites where the visualized interface adhesion tended to be better at higher loadings of both LLDPE and GF.     

Natural weathering test for films of various formulations of low density polyethylene (LDPE) and linear low density polyethylene (LLDPE)

Natural (outdoor) weathering test was performed to investigate the UV stability of thin films (0.06 mm) of linear low density polyethylene (LLDPE) and low density polyethylene (LDPE). The PE films were prepared from various formulations of LLDPE and LDPE resins. Some of these films contained a single high molecular mass HALS only, along with a primary antioxidant (i.e. Irganox 1010) and a secondary antioxidant (i.e. Irgafos 168 or Alkanox TNPP), while others contained HALS and UVA (i.e. Chimassorb 81 or Tinuvin P or Tinuvin 326) along with these antioxidants. The HALS used was either an oligomeric or a synergistic mixture of a high molecular mass (HMM) hindered amine stabilizer and co-additives. The UV stability was investigated by exposing the prepared films at 45° towards south in the direct sunshine up to 365 days. Fifty percent of tensile strength retention was determined for all these exposed films and it was found that the films containing a single HALS gained improved UV stability by about two to 12 fold over the pure films. On the other hand, films that contained a combination of HALS and UVA obtained further improved UV stability over the films containing a single HALS (both have antioxidants). Films containing a single HALS reached 50% TS retention within 205 days, whereas, films containing a combination of HALS and UVA reached 50% TS retention within 590 days, which is about three times further improvement in UV stability.     

Properties of ethylene propylene diene rubber/white and black filler composites cured by gamma radiation in presence of sorbic acid

The effect of incorporating sorbic acid (SA), an echo-friendly curing agent, and silica or carbon black (CB) filler, as well as gamma irradiation on the physico-chemical, mechanical and thermal properties of ethylene propylene diene monomer rubber (EPDM) was investigated. The results indicated that the developed composites revealed improvement in the studied parameters over the untreated samples. Filler incorporation into rubber matrix has been proven a key factor in enhancing the swelling resistance, tensile strength and thermal properties of the fabricated composites. The improvement in tensile strength and modulus was attributed to better interfacial bonding via SA. Alternatively, a comparison was established between the performance of the white and black fillers. The utmost mechanical performance was reported for the incorporated ratios 10 phr SA and 40 phr white filler into a 50 kGy irradiated composite. Meanwhile, the incorporation of CB yielded better thermally stable composites than those filled with silica at similar conditions.     

Polymer nanoparticles: their effect on rheological,thermal, and mechanical properties of linear low‐density polyethylene (LLDPE)

Rheological, thermal, and mechanical properties of polymer particle/LLDPE blends were studied in this paper. The blends were prepared individually by incorporating nanoparticles of polystyrene (nPS) of ～60 nm and polymethyl methacrylate (nPMMA) of ～50 nm with different wt% loading (i.e., 0.10–0.5%). It was shown from the experimental results that rheological, thermal and mechanical properties were increased as polymer particles blended with LLDPE. Blends with 0.25 wt% loading of nPS and 0.5 wt% loading of nPMMA exhibited better rheological, thermal, and mechanical properties compared with that of other wt% loadings. The improvements in properties were due to the close packing of LLDPE chains as recorded by improvement in crystallinity of LLDPE with addition of nPS and nPMMA as shown by SEM. Copyright © 2010 John Wiley & Sons, Ltd.     

Mechanical properties and characterization of slowly cooled isotactic polypropylene/high‐density polyethylene blends

In previous studies, we found that Young's moduli of quenched isotactic polypropylene/high‐density polyethylene (iPP/HDPE) exceeded the upper bound, calculated from the Voigt model, with the moduli of the quenched homopolymers as those of the two components. We suggested that this might be due to crystallization, as the components crystallized at higher temperatures in the blend than on their own. We repeated the same set of measurements, this time on iPP/HDPE blends that were cooled slowly. We also examined crystallization at various rates of cooling with differential scanning calorimetry. At slow cooling rates, the HDPE and iPP components in the blends crystallize at lower temperatures than in the pure homopolymers, suggesting that the presence of one component inhibits rather than promotes the crystallization of the other. Electron microscopy of slowly cooled blends revealed very different interfacial morphologies depending on whether the HDPE or the iPP crystallizes first. Young's moduli of most of the blends lie on the upper bound; however, some blends with co‐continuous morphologies fall well below the lower bound. The mechanical properties are discussed in terms of the interfacial morphology, the crystallization behavior, and the large‐scale phase separation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1384–1392, 2003     

Morphology and mechanical properties of blown films of a low‐density polyethylene/linear low‐density polyethylene blend

The morphologies of films blown from a low‐density polyethylene (LDPE), a linear low‐density polyethylene (LLDPE), and their blend have been characterized and compared using transmission electron microscopy, small‐angle X‐ray scattering, infrared dichroism, and thermal shrinkage techniques. The blending has a significant effect on film morphology. Under similar processing conditions, the LLDPE film has a relatively random crystal orientation. The film made from the LDPE/LLDPE blend possesses the highest degree of crystal orientation. However, the LDPE film has the greatest amorphous phase orientation. A mechanism is proposed to account for this unusual phenomenon. Cocrystallization between LDPE and LLDPE occurs in the blowing process of the LDPE and LLDPE blend. The structure–property relationship is also discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 507–518, 2002; DOI 10.1002/polb.10115     

Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking

Crystallisation studies on LLDPE/EVA blends and the individual components were performed with wide angle X-ray scattering (WAXS) technique and differential scanning calorimetry (DSC) DSC was used to characterise the quiescent crystallisation behavior. The heat of fusion and crystallinity of the blends were reduced by the addition of EVA. The experimental and theoretical values of crystallinity of the blends were found to be mutually agreeing. Crystallisation of LLDPE remains impeded to some extent due to the presence of amorphous EVA. Compatibilisation does not affect crystallinity whereas crosslinking decreases crystallinity. Crosslinking and compatibilisation make no significant change in the melting temperature of the blends. X-ray diffraction studies were carried out on un-crosslinked and crosslinked LLDPE/EVA blends with a view to study the effect of blend composition and crosslinking on crystallinity and lattice distance. Studies revealed that LLDPE and EVA have orthorhombic unit cell. Blending with EVA did not affect the crystalline structure of LLDPE, but the crystallinity decreases with EVA content. At low concentrations of EVA the lattice parameters remain unchanged. Above 30% EVA content however, a linear increase has been observed. Dicumyl peroxide (DCP) crosslinked samples show considerable shift of (1 1 0), (2 0 0) and (0 2 0) crystalline peaks towards lower 2θ values indicating an increase of unit cell parameters of the orthorhombic unit cell of polyethylene. At lower EVA-concentrations (<50%) the crystalline structure remains unchanged. For EVA-contents of more than 70% however, increasing DCP-content reduces the crystallinity of the blends and increases the lattice distance. This indicates that DCP-crosslinking is more effective in EVA phase than in the LLDPE phase.     

Polyamide 66/EPR‐g‐MA blends: mechanical modeling and kinetic analysis of thermal degradation

The present investigation deals with the mechanical, thermal, and morphological properties of binary nylon 66/maleic anhydride grafted ethylene propylene rubber (EPR‐g‐MA) blends at different dispersed phase (EPR‐g‐MA) concentrations. The effects of EPR‐g‐MA concentration and dispersed particle size on the mechanical properties of the blends were studied. Analysis of the tensile data in terms of various theoretical models revealed the variation of stress concentration effect with blend composition and the improvement of interfacial adhesion between dispersed rubber phase and nylon 66 matrix. The thermal degradation of the blends was analyzed by nonisothermal thermogravimetric analysis (TGA). It was found that the activation energy (E_a) and overall reaction order of thermal degradation decreased with increasing EPR‐g‐MA content. The scanning electron microscopic (SEM) analysis showed a significant decrease in dispersed particle size with increasing EPR‐g‐MA content, which was explained on the basis of the level of chemical interaction (in situ compatibilization) between nylon 66 and EPR‐g‐MA. The surface morphology of the nylon 66/EPR‐g‐MA blends was illustrated by the roughness of atomic force microscopy (AFM) images. Copyright © 2008 John Wiley & Sons, Ltd.     

Morphology,structure, and properties of in situ compatibilized linear low‐density polyethylene/polystyrene and linear low‐density polyethylene/high‐impact polystyrene blends

Blends of linear low‐density polyethylene (LLDPE) with polystyrene (PS) and blends of LLDPE with high‐impact polystyrene (HIPS) were prepared through a reactive extrusion method. For increased compatibility of the two blending components, a Lewis acid catalyst, aluminum chloride (AlCl₃), was adopted to initiate the Friedel–Crafts alkylation reaction between the blending components. Spectra data from Raman spectra of the LLDPE/PS/AlCl₃ blends extracted with tetrahydrofuran verified that LLDPE segments were grafted to the para position of the benzene rings of PS, and this confirmed the graft structure of the Friedel–Crafts reaction between the polyolefin and PS. Because the in situ generated LLDPE‐g‐PS and LLDPE‐g‐HIPS copolymers acted as compatibilizers in the relative blending systems, the mechanical properties of the LLDPE/PS and LLDPE/HIPS blending systems were greatly improved. For example, after compatibilization, the Izod impact strength of an LLDPE/PS blend (80/20 w/w) was increased from 88.5 to 401.6 J/m, and its elongation at break increased from 370 to 790%. For an LLDPE/HIPS (60/40 w/w) blend, its Charpy impact strength was increased from 284.2 to 495.8 kJ/m². Scanning electron microscopy micrographs showed that the size of the domains decreased from 4–5 to less than 1 μm, depending on the content of added AlCl₃. The crystallization behavior of the LLDPE/PS blend was investigated with differential scanning calorimetry. Fractionated crystallization phenomena were noticed because of the reduction in the size of the LLDPE droplets. The melt‐flow rate of the blending system depended on the competition of the grafting reaction of LLDPE with PS and the degradation of the blending components. The degradation of PS only happened during the alkylation reaction between LLDPE and PS. Gel permeation chromatography showed that the alkylation reaction increased the molecular weight of the blend polymer. The low molecular weight part disappeared with reactive blending. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1837–1849, 2003     

Nanostructures and thermal‐mechanical properties of cyanate ester/epoxy thermosets modified with poly(ethylene oxide)‐poly(propylene oxide)‐poly(ethylene oxide) triblock copolymer

Phase structures and mechanical properties of epoxy/acryl triblock copolymer alloys using several curing agents were studied. The nanostructured thermosets were obtained at the compositions investigated for every blends studied. The dependence of the morphological structures on block copolymer content and dicyanate ester, 2,2′‐bis(4‐cyanatophenyl) isopropylidene (BCE)/epoxy (EP) ratio for thermosetting blends was interpreted on the basis of the difference in hydrogen bonding interactions and reaction resulting from the cross‐linked network structures of matrixes. Moreover, the effect of F68 (poly(ethylene oxide)‐co‐poly(propylene oxide)‐co‐poly(ethylene oxide) block copolymer) on the curing characteristics and performance of BCE/EP resin was discussed. Results show that the incorporation of F68 cannot only effectively promote the curing reaction of BCE/EP but can also significantly improve the toughness of the cured BCE/EP resin. In addition, the toughening effect of F68/EP is greater than single EP resin. For example, the notched impact strength of systems with BE‐80/20 (B and E being the overall contents of BCE and EP, respectively) modified with 10 wt% F68 showed 55% increase compared with neat BCE/EP resin and even is more than three times of that value for pure BCE resin, 5.9 kJ/cm². Copyright © 2015 John Wiley & Sons, Ltd.     

Structure and properties of compatibilized recycled poly(ethylene terephthalate)/linear low density polyethylene blends

Blends of recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) were compatibilized with poly(styrene-ethylene/butyldiene-styrene) (SEBS) and maleic anhydride-grafted poly(styrene-ethylene/butyldiene-styrene) (SEBS-g-MA). Effects of compatilizer were evaluated systematically by study of mechanical, thermal and morphology properties together with crystallization behavior of PET. Tensile properties of the blends were improved effectively by the addition of 10 wt% SEBS-g-MA, elongation at break and charpy impact strength were increased with the increasing content of compatilizer. SEBS-g-MA is more effectual on mechanical properties of R-PET/LLDPE blends than SEBS. DSC analysis illustrates crystallinities of PET and LLDPE were increased by compatilizer at annealing condition. WAXD and FT-IR spectra show that annealing influences crystallization behavior of PET. Different compatilizer content results in different morphology structure, in particular, higher SEBS-g-MA content can induce the formation of a salami microstructure.     

Synthesis and characterization of polyethylene‐g‐polystyrene as the compatibilizer for polypropylene/ Polystyrene blends

Polyethylene‐g‐polystyrene (PE‐g‐PS) was synthesized as a compatibilizer for polypropylene/polystyrene­(PP/PS) blends by the living radical polymerization of styrene with polyethylene‐co‐glycidylmethacrylate (PE‐co‐GMA). The compatibilizer effect of PE‐g‐PS on the morphology and thermal properties of PP/PS blends was investigated. The crystalline temperature of PP in PP/PS blends decreased with increasing PE‐g‐PS contents. Morphologies of PP/PE‐g‐PS/PS blends showed much better dispersion of each domain for higher PE‐g‐PS contents. The molecular weight of PS segment in PP/PE‐g‐PS/PS blend was increased by addition of styrene monomer during the post melt blending process where post living radical polymerization reaction proceeded. Copyright © 2003 John Wiley & Sons, Ltd.     

Investigating the effect of accelerated weathering on the mechanical and physical properties of high content plastic solid waste (PSW) blends with virgin linear low density polyethylene (LLDPE)

In developing countries, plastic solid waste (PSW) poses a serious threat due to the increase in the dependency on landfilling as well as other environmental issues. Hence, valorising the accumulated waste is essential to promoting more environmentally friendly practices. In this work, the mechanical and physical properties of virgin linear low density (LLDPE) and LLDPE blends with PSW are reported. The formulations studied contained the following virgin to waste ratios (wt.%/wt.%): 100/0, 75/25, 50/50, 25/75 and 10/90. The effect of photo-degradation on the studied specimens was investigated using accelerated weathering tests in a UV chamber. Young's modulus showed an increase with exposure duration due to change in the samples' crystallinity. The loss of mechanical integrity (i.e. stress and strain at rupture) of the samples studied was related to the photo-degradation mechanisms, namely cross-linking and photo-oxidation. Haze and light transmission measured indicated that there was a loss of the amorphous regions in the samples studied after about 200 h of continuous exposure. The total change in colour (ΔE) was estimated but did not show a clear trend, indicating a clear dependency on wash mechanism and continuous loss of polymer colour and degradation.     

Studies on grafting of tris(2‐methoxyethoxy)vinylsilane onto ethylene‐propylene‐diene terpolymer

New graft copolymer was prepared by incorporating tris(2‐methoxyethoxy)vinylsilane (TMEVS) on ethylene‐propylene‐diene terpolymer (EPDM) by using dicumyl peroxide (DCP) as initiator, in Haake Rheocord 90 torque rheometer. The effect of EPDM concentration, TMEVS concentration, reaction time, reaction temperature and initiator concentration on the graft co polymerization was studied. The grafting efficiency of TMEVS on EPDM was confirmed by Fourier Transform infrared (FT‐IR) spectroscopy. The grafting efficiency increased with increase in the silane concentration upto 6% by weight. The grafting efficiency decreased beyond 6% by weight due to homopolymerization of TMEVS and non‐availability of carbon–carbon double bond in the EPDM terpolymer. The thermal properties of peroxide cured EPDM and hot water cured EPDM‐g‐TMEVS were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The results show thermal properties like degradation tempertature and glass transition temperature of the EPDM‐g‐TMEVS were increased due to introduction of TMEVS on to EPDM terpolymer as well as the formation of thermally stable three‐dimensional network. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of N‐methyl‐substituted polyurethane

We prepared N‐methyl‐substituted polyurethanes with different substitution degrees from sodium hydride, methyl p‐toluene sulfonate, and polyether–polyurethane containing poly(oxytetramethylene) glycol, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol. The chemical structures were characterized with Fourier transform infrared and ¹H NMR. To investigate the effects of the N‐substitution degree on the morphology, thermal stability, and mechanical properties, we used differential scanning calorimetry, thermogravimetric analysis, and a universal testing machine. As the substitution degree increased, the new free (1708 cm^?1) and bonded (1650 cm^?1) carbonyl peaks increased. There was no bonded carbonyl peak in fully substituted polyurethane because the urethane groups had no hydrogen. At a small substitution degree, we observed a slight increase in the glass‐transition temperature and decrease in the endotherms of soft‐segment and hard‐segment domains due to the decrease in the hard‐segment domain and the increase in the urethane groups in the soft‐segment domain. The hard‐segment domain decreased and then disappeared as the N‐methyl substitution degree increased. These changes in the morphology resulted (1) in decreased modulus and tensile strength for the films because of the decrease in physical crosslinking points and (2) improved thermal stability as the substitution degree increased. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4077–4083, 2002     

Binary and ternary blends of high‐density polyethylene with poly(ethylene terephthalate) and polystyrene based on recycled materials

Binary blends of recycled high‐density polyethylene (R‐HDPE) with poly(ethylene terephthalate) (R‐PET) and recycled polystyrene (R‐PS), as well as the ternary blends, i.e. R‐HDPE/R‐PET/R‐PS, with varying amounts of the constituents were prepared by twin screw extruder. The mechanical, rheological, thermal, and scanning electron microscopy (SEM) analyses were utilized to characterize the samples. The results revealed that both R‐HDPE/R‐PET and R‐HDPE/R‐PS blends show phase inversion but at different compositions. The R‐PET was found to have much higher influence on the properties enhancement of the R‐HDPE compared to R‐PS, but at the phase inverted situation, a significant loss in the tensile strength of R‐HDPE/R‐PET blend was observed due to the weak interaction at this morphological state. However, the ternary blends with higher loading of second phase, namely greater than 50 wt% of R‐PET+R‐PS, demonstrated better mechanical properties than the binary blends with the same content of either R‐PET or R‐PS. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of poly(ethylene oxide)‐grafted polyethylene copolymer and terpolymer

A series of graft copolymers were synthesized based on ethylene‐co‐m,p‐methylstyrene (EMS) (backbone copolymer), ethylene‐1‐hexene‐m,p‐methylstyrene (EHMS) (backbone terpolymer), and polyethylene glycol monomethyl ethers (PEGM) (grafts) in this study. The PEGMs with molecular weights of 750 and 2000 were used. The chemical composition of the graft copolymers was analyzed by NMR and DSC measurements. The graft copolymers exhibited a phase‐separated morphology with the backbone and the methoxy polyethylene glycol (MPEG) grafts forming separate crystalline phases. The MPEG phase had a melting temperature lower than the corresponding MPEG homopolymer, as determined by DSC. The melting point of the crystalline phase formed by the EMS and EHMS main chains was lower than that of pure polymer backbone. Copyright © 2009 John Wiley & Sons, Ltd.     

Phase behavior of blends of linear low density polyethylene and poly(ethene-propene-1-butene)

The aim of this work was the study of blends of linear low density polyethylene (LLDPE) and an ethene-propene-1-butene terpolymer (t-PP). Two types of polyethylene were used to prepare the blends: an ethene-co-1-hexene (LLDPE(H)) copolymer and an ethene-co-1-octene (LLDPE(O)) copolymer. These copolymers present similar comonomer contents, molar mass, molar mass distribution and catalyst systems, but differ in their comonomer distribution. The blends were obtained through mechanical mixing using a single screw extruder at different compositions: 20, 40, 50, 60 and 80 wt.% of LLDPE. From DSC measurements two separated melting and crystallization peaks were observed and dynamic mechanical analysis showed two glass transitions indicating that LLDPE/t-PP blends are immiscible in amorphous and crystalline phases in the solid state. X-ray diffraction showed that the unit cell parameters of both polymers in the blends remain unchanged independent of the composition of the blend.     

Preparation of polypropylene/ethylene‐propylene‐diene terpolymer/nitrile rubber ternary thermoplastics vulcanizates with good mechanical properties and oil resistance by core‐shell dynamic vulcanization

As the most successful commercialized thermoplastic vulcanizates (TPVs), polypropylene (PP)/ethylene propylene rubber (EPDM) TPVs exhibit poor oil resistance. In this work, we prepared PP/EPDM/butadiene acrylonitrile rubber (NBR) ternary TPVs with good oil resistance using core‐shell dynamic vulcanization. According to the theoretical analysis of the spreading coefficient and the transmission electron microscopy results, the rubber phases exhibited a special core‐shell structure, in which the cross‐linkedNBR‐core was encapsulated by the EPDM‐shell. The core‐shell structure effectively improved the interfacial compatibility between PP and NBR phase as the EPDM‐shell could avoid the direct contact of them, thus improving the mechanical properties of the TPVs. For example, the PP/EPDM/NBR (40/30/30) ternary TPV showed enhanced tensile strength of 12.57 MPa, compared with 10.71 MPa of PP/EPDM (40/60) TPV and 11.11 MPa of PP/NBR (40/60) TPV, respectively. Moreover, the oil resistance of the TPVs was also improved. Compared with PP/EPDM TPV, the change rates in mass, volume, tensile strength and elongation at break of PP/EPDM/NBR TPV after oil immersion decreased by 42.18%, 48.69%, 52.68% and 28.77%, respectively.