Contribution of steric and electrostatic repulsion forces to the stability of styrene latices copolymerized with acrylic acid

Acrylic acid (AA) is used in many emulsion polymerization formulations to improve the colloidal stability of the latex product. The improved stability originates from electrostatic repulsion complemented with steric repulsion. The strength of the electrostatic and steric repulsion forces in a styrene (S)/AA copolymer latex was investigated at different pH values, electrolyte concentrations, and temperatures. A comparison was made with an S homopolymer latex. Transmission electron microscopic pictures, combined with visual inspections, provided understanding of the mechanisms leading to coagulation in polystyrene (PS)/AA copolymer latices. Colloidal stability of the unswollen sodium dodecyl sulfate stabilized PS latex is based on electrostatic repulsion. Destabilization by sodium chloride resulted in aggregation. The acidic PS/AA latex remained stable against aggregation at high electrolyte concentrations because of steric repulsion. The acidic PS/AA latex showed a strong tendency to flocculate at increasing electrolyte concentrations. Flocculation was not observed for high‐pH PS/AA latices at high electrolyte concentrations. Steric repulsion of the acid PS/AA latex was lost at temperatures higher than the critical coagulation temperature (35 °C), and flocculation was followed by aggregation and coalescence. The high‐pH PS/AA latex was stable even at high electrolyte concentrations and temperatures up to 80 °C because of strong electrosteric stabilization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2985–2995, 2003     

Participation of electrolyte cations in albumin adsorption onto negatively charged polymer latices

The participation of electrolyte cations in the adsorption of bovine serum albumin (BSA) onto polymer latices was investigated. The latices used were hydrophobic polystyrene (PS), and hydrophilic copolymers, i.e., styrene (St)/2-hydroxyethyl methacrylate(HEMA) copolymer [P(St/HEMA)] and styrene/acrylamide (AAm) copolymer [P(St/AAm)]. Three kinds of electrolyte cations (Na⁺, Ca²⁺, Mg²⁺) were used as the chloride. The amount of BSA adsorbed in every cation medium showed a maximum near the isoelectric point (iep, pH about 5) of the protein. The amounts of BSA adsorbed onto copolymer latices (except in the acidic pH region lower than the iep) were considerably smaller than that onto PS latex because of the steric repulsion and the decrease in the hydrophobic interaction between BSA and copolymer latices. In the acidic pH region, there was little difference in the amount of BSA adsorbed in every cation medium. However, in the pH region higher than the iep, the amounts of BSA adsorbed (particularly onto PS latex) in divalent cations (Ca²⁺ and Mg²⁺) media were relatively greater compared with that in a monovalent (Na⁺) one. This result was interpreted on the basis of the differences in such effects of electrolyte cations as dehydration power, suppression of the electrostatic repulsion, and binding affinity to BSA molecule. Ion Chromatographic estimation of the amounts of electrolyte cations captured upon BSA adsorption (in pH > 5) revealed that divalent cations were incorporated into the contact interface between the latex and BSA molecule so as to prevent the accumulation of anion charge and facilitate the protein adsorption.     

Synthesis and characterization of amphoteric latex particles

Stable monodisperse amphoteric latex particles were prepared by the semibatch surfactant-free emulsion copolymerization of methyl methacrylate and methacrylic acid (MAA) initiated by 2,2'-azobis(2-amidinopropane) dihydrochloride (V-50). These submicron particles have a net positive charge, which is attributed to the ionized amino group at low pH. In contrast, they become negatively charged owing to the ionized carboxyl group at high pH. There exists a pH at which these particles exhibit a net charge of zero (pI). At a constant level of V-50, the pI value of these latices decreases with increasing amount of MAA used in the polymerization recipe. The effect of pH on the colloidal stability of these amphoteric latices toward the addition of the negatively charged latex was investigated. The resultant coagulation kinetics was used to study the electrostatic interaction between the amphoteric particles and negatively charged particles.     

Electrokinetic behavior and colloidal stability of polystyrene latex coated with ionic surfactants

This work is focused on analyzing the electrokinetic behavior and colloidal stability of latex dispersions having different amounts of adsorbed ionic surfactants. The effects of the surface charge sign and value, and the type of ionic surfactant were examined. The analysis of the electrophoretic mobility (mu(e)) versus the electrolyte concentration up to really high amounts of salt, much higher than in usual studies, supports the colloidal stability results. In addition, useful information to understand the adsorption isotherms was obtained by studying mu(e) versus the amount of the adsorbed surfactant. Aggregation studies were carried out using a low-angle light scattering technique. The critical coagulation concentrations (ccc) of the particles were obtained for different surfactant coverage. For latex particles covered by ionic surfactants, the electrostatic repulsion was, in general, the main contribution to the colloidal stability of the system; however, steric effects played an important role in some cases. For latices with not very high colloidal stability, the adsorption of ionic surfactants always improved the colloidal stability of the dispersion above certain coverage, independently of the sign of both, latex and surfactant charge. This was in agreement with higher mobility values. Several theoretical models have been applied to the electrophoretic mobility data in order to obtain different interfacial properties of the complexes (i.e., zeta potential and density charge of the surface charged layer).     

Deposition of polymer latices on grafted Nylon 6 fiber

Deposition of polymer latices on a grafted Nylon 6 fiber was studied as a function of pH and the degree of grafting. The latices were polystyrene (PS), styrene/acrylamide copolymer (P(St/AAm)) and styrene/acrylic acid copolymer (P(St/AA)). The deposition of the latices on the grafted fiber decreased in every case with increasing pH and no deposition was observed at alkaline pH. The grafting of fiber with acrylic and methacrylic acid reduced the deposition of P(St/AAm) and P(St/AA) latices but had no influence on the deposition of PS latex. The relation between the deposition rates and the interaction energy at acidic pH indicates that the deposition of PS latex on the grafted fiber mainly depends on the electrostatic interaction. These results suggest that the expansion of water-soluble polyelectrolyte layer on the surface of grafted fiber plays an important role on the deposition.     

Studies on the preparation and characterization of monodisperse polystyrene latices. VI. Preparation of zwitterionic latices

The preparation of zwitterionic latex particles is reported by using a mixed anionic and cationic initiator system without requiring surface-active agents. Isoelectric points were found from microelectrophoresis experiments and were in the pH range of 3.5-5. Close to the isoelectric point, the latices coagulated as expected, and good stability was achieved outside this narrow range. This range of stability was in good agreement with predictions from current theory. Redispersion after coagulation was found to be difficult as was expected for a hydrophobic colloid. The electrokinetic behavior did not result in the maximum in zeta potential at an electrolyte concentration of 1 mM unlike the situation for other hydrophobic polystyrene latex particles, and hence these systems may be even better models for other colloidal studies.     

Chemical heterogeneity in emulsion copolymers of carboxylic monomers

Copolymer latices of butylacrylate (BA) with acrylic and methacrylic acid (AA and MAA) were prepared by batch type emulsion polymerization, and, for comparison, copolymers with identical monomer composition were prepared by batch type solution polymerization.The distribution of the carboxylic monomers in the latex particles and the serum was studied by density gradient and sedimentation experiments with the analytical ultracentrifuge. Dynamic mechanical measurements of films of these copolymers were used to determine the storage and loss moduli as a function of temperature. From these measurements the position and extension of the glass transition range on the temperature scale is obtained. For heterogeneous emulsion copolymers with two glass transition temperatures the distribution of the carboxylic monomer units in the different copolymer phases can be determined. Electron microscopy of ultra thin cross-sections of stained films gave further insight into the film morphology.The combination of the results obtained with the different methods gives rise to the following clues: In the BA/AA latices about 40% (by weight) of the total AA used in the recipe are found in the serum as a water soluble polymer, about 50% are found to increase the glass transition temperatureT _g of the bulk of the BA copolymer and, therefore, are thought to be incorporated into the interior of the latex particles, and the remaining 10% are, conclusively, located on the particle surface.In the BA/MAA latices no water soluble copolymer could be detected in the serum, about 90% of the MAA used is found in the bulk of the copolymer, and about 10% form a second hard phase on the surface of the latex particles.Dynamic mechanical measurements on the copolymer latex films show at least two phases with different glass transition temperatures: the bulk of the copolymer with a relatively low content of (M)AA units and a glass transition range at low temperatures, and a second (M)AA rich phase with a highT _g.The latter phase forms a honeycomb-like structure surrounding the packed latex particles. That results in a three-dimensional network of polymer with a highT _g extending throughout the latex film. In spite of the fact that this phase is built from a small fraction of the total copolymer only, it has a very pronounced influence on the performance behaviour of latex films.Dedicated to Professor Dr. R. Manecke on the occasion of his 70th birthday.     

Acetal‐functionalized polymer particles useful for immunoassays. II. Surface and colloidal characterization

Monodisperse polymer colloids with dimethyl and diethyl acetal functionalities were synthesized by a two‐step emulsion polymerization process. The first step consisted of a batch emulsion homopolymerization of styrene (St). The dimethyl and diethyl acetal functionalities were obtained by batch emulsion terpolymerization of St, methacrylic acid (MAA), and methacrylamidoacetaldehyde dimethyl acetal (MAAMA) or methacrylamidoacetaldehyde diethyl acetal (MAADA) in the second step, onto the previously formed polystyrene latex particles. The latexes were characterized by TEM and conductimetric titration, in order to obtain the particle size distribution and the amount of carboxyl and acetal groups on the surface, respectively. The chemical stability of the functionalized surface groups during the storage time was analyzed. The hydrophilic character of the surface of the polymer particles was determined by means of nonionic emulsifier titration. The colloidal stability of the synthesized latexes was studied by measuring the critical coagulation concentration (CCC) against KBr electrolyte, and the existence of a hairy layer on the surface of the latex particles was analyzed by measuring the hydrodynamic particle diameter at several electrolyte concentrations. The surface functionalized groups remained stable for 2 years. The relative hydrophilic character and the colloidal stability were affected by the pH of the medium. On the other hand, the higher the surface charge, the larger the thickness of the hairy layer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 501–511, 1999     

Preparation of a xanthate‐terminated dextran by click chemistry: Application to the synthesis of polysaccharide‐coated nanoparticles via surfactant‐free ab initio emulsion polymerization of vinyl acetate

Stable monodisperse poly(vinyl acetate) (PVAc) submicronic latex particles were synthesized by ab initio batch emulsion polymerization using a dextran derivative from renewable resource as an efficient steric stabilizer. The dextranend‐functionalized by a xanthate moiety was synthesized by Huisgen's 1,3‐dipolar cycloaddition (click chemistry). It was applied as a macromolecular RAFT (reversible addition fragmentation chain transfer) agent in surfactant‐free emulsion polymerization of vinyl acetate to form in situ an amphiphilic block copolymer able to efficiently stabilize the latex particles. The method afforded the preparation of high solids content (27%) latices coated by dextran. Both the kinetic study and the molar mass analyses confirmed the involvement of the dithiocarbonate group in the emulsion polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2845–2857, 2008     

Hydrophilicity of polymer effects on controlled particle coagulation in batch emulsion polymerization

The poly(methyl methacrylate-co-styrene) was prepared by batch emulsion polymerization to clarify the effect of characteristics of polymer on particle coagulation. Experimental results showed that the size of final latex particle increased with increasing methyl methacrylate in initial recipe, ranged from 84 to 193 nm, which was attributed to the particle coagulation. With the methyl methacrylate increased, the hydrophilicity of polymeric particle improved, thus led to the surfactant molecules packed loosely on the polymer surface, further, enhanced particle coagulation occurred. On the contrary, the surfactant molecules adsorbed on tightly the polymeric particle surface (methyl methacrylate content low) surface led to the electrostatic repulsion energy of polymer particle improved, and polymer particle stability was also improved. Thus, combined with the results previously reported by us (Colloid Polym Sci 291: 2385–2398, 2013 and Colloid Polym Sci 292: 519-525, 2014), the particle coagulation depended not only on the aqueous phase such as electrolyte concentration and methanol content, but also on the nature of polymer such as hydrophilicity.     

Suppressing the long‐chain branching in the synthesis of poly(styrene‐b‐butyl acrylate‐b‐styrene) in RAFT emulsion polymerization by tuning the interfacial properties

Reversible addition‐fragmentation chain transfer (RAFT) emulsion polymerization is becoming an important technique to synthesize the latex of block copolymers. A previous study showed that in the synthesis of polystyrene‐b‐poly(butyl acrylate)‐b‐polystyrene triblock copolymer via RAFT emulsion polymerization using amphiphilic oligo(acrylic acid‐styrene) macroRAFT as surfactant and mediator, the molecular weight distribution could be much broadened to PDI higher than 2. In this study, an in‐depth investigation was performed to decrease PDI. It was found that long‐chain branches could be formed in the synthesis of triblock block copolymer, leading to the appearance of a higher molecular weight shoulder in the GPC curve of the final product. The lower neutralization degree of acrylic acid (AA) units on the macroRAFT and shorter AA chains would help to suppress the formation the long‐chain branches, leading to PDI around 1.5. It is evidenced that the successful suppression is due to the promotion of radical entry as a result of decreased interfacial transport impedance. It is also evidenced that the presence of styrene during the polymerization of butyl acrylate could promote the formation of long chain branches. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1464–1473     

Nanostructured latexes made by a sequential multistage emulsion polymerization

A series of linear and lightly crosslinked nanostructured latices was prepared by a sequential multistage semicontinuous emulsion polymerization process alternating styrene (S) and n‐butyl acrylate (BA) monomer feeds five times, that is ten stages, and vice versa, along with several control latices. Transmission electron micrographs of the RuO₄‐stained cross sections of nanostructured and copolymer latex particles and films showed that their particle morphologies were not very different from each other, but the nanostructured latex particles were transformed into a nanocomposite film containing both polystyrene (PS) and poly(n‐butyl acrylate) (PBA) nanodomains interconnected by their diffuse polymer mixtures (i.e. interlayers). The thermal mechanical behaviors of the nanostructured latex films showed broad but single T_gs slightly higher than those of their counterpart copolymer films. These single T_gs indicated that their major component phases were the diffuse interlayers and that they behaved like pseudopolymer alloys. The minimum film formation temperatures of nanostructured latices capped with PBA and PS, respectively, were 15 °C lower than and equal to those of their counterpart copolymer latices, but their T_gs were about 10 °C higher. Consequently, nanostructured latices enabled us to combine good film formation with high strengths for adhesives and coatings applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2826–2836, 2006     

Synthesis of polystyrene latex with amphoteric surfactant and its characterization

An emulsion polymerization of styrene in the presence of an amphoteric surfactant; N,N-dimethyl-n-laurylbetaine (LNB) was carried out at pH 7.0. The polymerization rate and the concentration of the latex particle were proportional to the LNB concentration of 0.6 power. The latex particle sizes became smaller with increasing concentrations of LNB. The molecular weights of polystyrene latices increased with the concentration of LNB. The zeta-potentials of latex particles were significantly dependent on the pH, and showed the existence of an isoelectric point.     

Highly magnetic latexes from submicrometer oil in water ferrofluid emulsions

The synthesis of functionalized submicrometer magnetic latex particles is described as obtained from a preformed magnetic emulsion composed of organic ferrofluid droplets dispersed in water. Composite (polystyrene/γ‐Fe₂O₃) particles were prepared according to a two‐step procedure including the swelling of ferrofluid droplets with styrene and a crosslinking agent (divinyl benzene) followed by seeded emulsion polymerization with either an oil‐soluble [2,2′‐azobis(2‐isobutyronitrile)] or water‐soluble (potassium persulfate) initiator. Depending on the polymerization conditions, various particle morphologies were obtained, ranging from asymmetric structures, for which the polymer phase was separated from the inorganic magnetic phase, to regular core–shell morphologies showing a homogeneous encapsulation of the magnetic pigment by a crosslinked polymeric shell. The magnetic latexes were extensively characterized to determine their colloidal and magnetic properties. The desired core–shell structure was efficiently achieved with a given styrene/divinyl benzene ratio, potassium persulfate as the initiator, and an amphiphilic functional copolymer as the ferrofluid droplet stabilizer. Under these conditions, ferrofluid droplets were successfully turned into superparamagnetic polystyrene latex particles, about 200 nm in size, containing a large amount of iron oxide (60 wt %) and bearing carboxylic surface charges. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2642–2656, 2006     

Preparation,morphology, and thermoresponsive properties of poly(N‐isopropylacrylamide)‐based copolymer microgels

In this research, thermoresponsive copolymer latex particles with an average diameter of about 200–500 nm were prepared via surfactant‐free emulsion polymerization. The thermoresponsive properties of these particles were designed by the addition of hydrophilic monomers [acrylic acid (AA) and sodium acrylate (SA)] to copolymerize with N‐isopropylacrylamide (NIPAAm). The effects of the comonomers and composition on the synthesis mechanism, kinetics, particle size, morphology, and thermoresponsive properties of the copolymer latex were also studied to determine the relationships between the synthesis conditions, the particle morphology, and the thermoresponsive properties. The results showed that the addition of hydrophilic AA or SA affected the mechanism and kinetics of polymerization. The lower critical solution temperature (LCST) of the latex copolymerized with AA rose to a higher temperature. However, because the strong hydrophilic and ionic properties of SA caused a core–shell structure, where NIPAAm was in the inner core and SA was in the outer shell, the LCST of the latex copolymerized with SA was still the same as that of pure poly(N‐isopropylacrylamide) latex. It was concluded that these submicrometer copolymer latex particles with different thermoresponsive properties could be applied in many fields. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 356–370, 2006     

Amphiphilic ABA triblock copolymer as surfactant in syntheses of microlatexes bearing cationic groups

Polystyrene microlatexes have been prepared by conventional emulsion polymerization with a novel amphiphilic water‐soluble ABA triblock copolymer, poly[2‐(dimethylamino)ethyl methacrylate]₁₅‐b‐poly(propylene oxide)₃₆‐b‐poly[2‐(dimethyl‐amino)ethyl methacrylate]₁₅ (PDMAEMA₁₅‐PPO₃₆‐PDMAEMA₁₅), as a polycationic emulsifier under acidic or neutral conditions. The ABA triblock copolymer was developed by oxyanion‐initiated polymerization in our laboratory. In this study, it acted well both as a polycationic polymeric surfactant to form block copolymeric micelles for emulsion polymerization and as a stabilizer to be anchored into the polystyrene microlatex or adsorbed onto its surface. The results obtained with various copolymer concentrations and different pH media showed that microlatex diameters decreased remarkably with increased concentration of this ABA triblock copolymeric emulsifier, but were not as much affected by the pH of media within the experimental range of 3.4–7.0. The observed difference of the particle sizes from transmission electron microscopy and dynamic light scattering measurements is discussed in terms of the effect of the absorbed surfactants and their electrical double layers. This difference has led to the formation of a cationic polyelectrolyte fringe on the surface of microspheres. The final microlatexes were characterized with respect to total conversion, particle diameter, and particle size distribution as well as colloidal stability. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3734–3742, 2002     

Preparation and characterization of latices with hydrophobic core and hydrophilic shell

Anionic and non-ionic copolymer latices with a hydrophobic core and hydrophilic shell were prepared using emulsifier-free emulsion polymerization. Styrene was used as the hydrophobic monomer; acrylic acid, acrylamide, and methacrylamide were employed as the hydrophilic monomers. The amount of chemically bound hydrophilic monomers in latex and unbound homopolymers in water were determined. The salt stability and redispersability of latices in water after spray-drying were also investigated.     

Long‐term stability of an ambient self‐curable latex based on colloidal dispersions in water of two reactive polymers

An ambient self‐curable latex (ASCL) was prepared via the blending of colloidal dispersions in water of a chloromethylstyrene‐functionalized copolymer and a tertiary‐amine‐functionalized copolymer. Upon casting and drying under ambient conditions, the ASCL could generate crosslinked continuous polymer films. The crosslinking occurred via the Menschutkin reaction (quaternization) between the two types of functional groups. Because this reaction was reversible at high temperatures, the films could be decrosslinked and hence were self‐curable. The prepared ASCL exhibited excellent colloidal and chemical stability during long‐term storage: no significant changes in the colloidal properties, such as the particle size, electrophoretic mobility, and crosslinking reactivity, were observed after 48 months of storage. The electrophoretic measurements indicated that the electrostatic repulsion between the negatively charged particles of the ASCL was responsible for the excellent stability. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2598–2605, 2005     

Batch emulsion copolymerization of 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐α‐D‐glucofuranose and butyl acrylate: Synthesis and properties of the sugar latices

To obtain new polymer latices based on sugar derivative, batch emulsion copolymerizations of 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐α‐D ‐glucofuranose (3‐MDG) and n‐butyl acrylate (BA) were carried out at 70 °C, with potassium persulfate as the initiator. 3‐MDG polymerizes faster than BA because of its higher reactivity ratio, r_(3‐MDG) = 1.94 versus r_(BA) = 0.54. The effect of the initial monomer composition on the polymerization rate and the thermal properties of the end copolymers was investigated. The overall rate of polymerization increases by enhancing the sugar content in the initial monomer composition. The glass‐transition temperature is linearly related to the sugar content in the copolymer. The influence of the type of surfactant showed that the particle size increases by changing from ionic to nonionic surfactant. Furthermore, the effect of the added acrylic acid (AA) on the rheological properties suggests that the sugar latices exhibit different non‐Newtonian flows depending on the pH of the latex and on the AA concentration on the particle surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 788–803, 2003     

Viscoelastic properties of polystyrene and poly(methyl methacrylate) dispersions sterically stabilized by hydrophobically modified inulin (polyfructose) polymeric surfactant

Recently, steric repulsive forces induced by a new graft copolymer surfactant, which is based in inulin (polyfructose), have been described. Previous investigations by atomic force microscopy between solid surfaces covered with adsorbed surfactant indicated strong repulsive forces even at high electrolyte concentration, due to the steric repulsion produced by the surfactant hydration. In the present paper, the colloidal stabilization provided by this surfactant is studied by rheology. The measurements were carried out on sterically stabilized polystyrene (PS) and poly(methyl methacrylate) (PMMA) containing adsorbed surfactant (INUTEC SP1). Steady-state shear stress as a function of shear rate curves was established at various latex volume fractions. The viscosity volume fraction curves were compared with those calculated using the Doughtry-Krieger equation for hard sphere dispersions. From the experimental eta r-phi curves the effective volume fraction of the latex dispersions could be calculated and this was used to determine the adsorbed layer thickness Delta. The value obtained was 9.6 nm, which is in good agreement with that obtained using atomic force microscopy (AFM). Viscoelastic measurements of the various latex dispersions were carried out as a function of applied stress (to obtain the linear viscoelastic region) and frequency. The results showed a change from predominantly viscous to predominantly elastic response at a critical volume fraction (phi c). The effective critical volume fraction, phi eff, was calculated using the adsorbed layer thickness (Delta) obtained from steady-state measurements. For PS latex dispersions phi eff was found to be equal to 0.24 whereas for PMMA phi eff=0.12. These results indicated a much softer interaction between the latex dispersions containing hydrated polyfructose loops and tails when compared with latices containing poly(ethylene oxide) (PEO) layers. The difference could be attributed to the stronger hydration of the polyfructose loops and tails when compared with PEO. This clearly shows the much stronger steric interaction between particles stabilized using hydrophobically modified inulin.