以天然植物为模板合成高度有序的多级复合孔材料

筛选出两种孔径较大且孔结构规则的植物为大孔模板, 以嵌段共聚物为介孔相模板成功合成了两种具有连续的骨架和贯通的大孔孔道(大孔孔径大于40 μm, 其孔壁为介孔相)的高度有序多级复合孔材料. 对该复合孔材料进行了水热稳定性研究. 用扫描电子显微镜(SEM)、粉末X射线衍射仪(XRD)、高分辨率透射电镜(HRTEM)以及N₂吸附-脱附等测试手段对合成的样品进行了表征. 结果表明, 合成的产物是孔道相互贯通的多级有序复合孔硅材料, 具有较好的水热稳定性. 采用此合成方法可精确地复制大孔植物模板.     

介孔二氧化钛的合成及其对甲基橙降解的光催化活性

以十六烷基三甲基溴化铵为模板剂,通过水解钛酸正丁酯合成了介孔二氧化钛分子筛,探讨了合成条件的影响。采用X射线粉末衍射(XRD)、红外光谱(FT-IR)、透射电子显微镜(TEM)和N2吸附-脱附等技术对介孔二氧化钛的晶相、结构、形貌、比表面积和孔径分布进行了表征。实验结果表明:得到的介孔二氧化钛分子筛的孔径为4-4.3nm,用抽提的方法去除模板剂得到的介孔二氧化钛的比表面积比焙烧的要高。以甲基橙为模型污染物,检验了所合成介孔二氧化钛的光催化性质。     

铈掺杂的介孔分子筛的水热合成与结构性能

以硅酸钠、硝酸铈铵为原料,十六烷基三甲基溴化铵为模板剂,通过水热法合成铈掺杂的介孔分子筛CeMCM-41.分别采用X射线粉末衍射(XRD)、透射电子显微镜(TEM)、红外光谱(FT-IR)、紫外-可见分光光度计(UV-Vis)和N2吸附-脱附等技术对产物的晶相、结构、形貌、比表面积和孔径进行表征.同时研究硅铈物质的量比对合成材料结构性能的影响.实验结果表明:水热条件下成功合成出铈掺杂的MCM-41介孔分子筛,其比表面积为480.5～1 295.2m2/g,平均孔径在2.70～6.29 nm之间.随着稀土元素铈的掺杂量的增加,CeMCM-41介孔分子筛的比表面积和孔体积变小,介孔有序性变差.     

介孔碳材料CMK-3的合成及其吸附性能研究——介绍一个综合化学实验

介绍一个集物理化学、分析化学和无机化学为一体的综合实验——介孔碳材料CMK-3的合成及其吸附性能研究。实验通过合成具有高比表面积的介孔碳材料CMK-3,运用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和氮气吸附/脱附技术表征材料的形貌和多孔结构;考察了介孔碳材料CMK-3对水溶液中次甲基蓝染料分子的吸附性能。     

二元阴阳离子表面活性剂法合成介孔氧化硅囊泡

以十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)为表面活性剂, 在SDS与CTAB的摩尔比为1.0~2.3时, 以正硅酸乙酯(TEOS)为硅源, 在氨水-水体系中于68℃下合成介孔氧化硅囊泡. 通过透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 热重分析仪(TGA)和氮气吸附-脱附实验仪对合成的产物进行表征. 结果表明, 合成的产物为介孔氧化硅囊泡聚集体, 孔径约为4 nm, 样品的Brunauer-Emmett-Teller(BET)比表面积为826 m²/g. 对介孔氧化硅囊泡的形成机理做了初步探讨.     

无序介孔硅复合纳米结构的制备与慢活化行为

通过对SiO_2纳米粒子进行镁热还原及后处理,制备了多级无序Si介孔复合纳米结构MP-Si@SiO_x@C,此结构展现出容量非衰减缓升的电化学慢活化行为,可抵消循环容量常规衰减趋势,赋予负极优良的循环稳定性.通过X射线衍射(XRD)、透射电子显微镜(TEM)、场发射扫描电子显微镜(SEM)、N_2吸附-脱附测试和孔径分布模拟分析发现,Si介孔组织包含微-窄介孔(1~5 nm)、中介孔(5~20 nm)以及大介孔-宏孔(20~100 nm)三级孔道,分别源于原初级粒子内部孔道、粒子团聚堆垛与粒内酸蚀、团聚体再堆垛;此合成装配方法有效提升了Si材料的堆积密度,电池电极能获得较高的体积比容量和储能密度.     

CTAB-P123辅助制备有序介孔KF/Al-Ce-SBA-15固体碱及其催化性能

为了缩短有序介孔氧化硅(SBA-15)基固体碱催化剂的工艺流程,制备长程有序介孔固体碱,本文以十六烷基三甲基溴化胺(CTAB)-三嵌段表面活性剂P123为模板剂,以KF为改性剂,两步法合成有序介孔KF/Al-Ce-SBA-15(KF/ACS)固体碱催化剂,采用小角X射线衍射(小角XRD)、N₂吸附-脱附曲线、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、CO₂程序升温脱附(CO₂-TPD)等手段,对催化剂的结构与性能进行表征,并研究了其在合成丙二醇甲醚(PM)中的催化性能。 当n(Al)/n(Ce)=0.12,KF的质量分数为10%时,KF/ACS催化剂不仅能够保持长程有序介孔结构,并且显示出强碱性能。 在催化甲醇与环氧丙烷(PO)合成PM的反应中,PM的收率达到92.0%,1-甲氧基-2-丙醇(PPM)选择性达到96.1%以上,并能有效抑制二丙二醇甲醚等副产物。     

金属有机框架@介孔分子筛复合材料的构建和性质

通过蒸汽诱导内部水解法(VIH)在介孔分子筛SBA-15孔壁上引入Al_2O_3,合成得到Al_2O_3@SBA-15复合物,随后与对二苯甲酸配体反应,从而制备得到金属有机框架化合物(MIL-53)与介孔分子筛(SBA-15)复合材料(MIL-53@SBA-15)。采用粉末X射线衍射(PXRD)、N_2吸附-脱附测试、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等技术证明成功合成了MIL-53@SBA-15复合材料。染料吸附实验结果表明,MIL-53@SBA-15复合材料相比于SBA-15、MIL-53及其物理混合样品,表现出对丁基罗丹明染料更高效吸附特性。     

三头季铵盐阳离子表面活性剂合成菱形十二面体介孔二氧化硅单晶

由于介孔二氧化硅单晶规整的外观形貌和有序的内部孔道结构性能, 使其在微激光器件领域具有十分重要的潜在应用. 试着用高电荷密度的阳离子三头季铵盐表面活性剂(C18-2-3-1)作模板剂, 用正硅酸四乙酯作无机前驱体, 在硫酸介质中通过调变有机-无机物种之间的协同组装作用, 成功地合成了具有简单立方相Pm3n结构的介孔二氧化硅单晶. 扫描电子显微镜(SEM)观察到这种介孔二氧化硅单晶具有菱形十二面体形貌, X射线衍射(XRD)和透射电子显微镜(TEM)测试结果证实这种介孔单晶属于简单立方Pm3n对称结构. 氮气吸附数据测得这种单晶具有较大的BET比表面积(550 cm2/g), 较大的孔体积(BJH 0.20 cm3/g)和孔径(BJH 2.4 nm).     

以一种新型Gemini表面活性剂作为介孔模板剂通过转晶过程合成介孔ZSM-5分子筛

将一种新型Gemini表面活性剂,丙撑基双(十八烷基二甲基氯化铵)[C18H37(CH3)2–N+–(CH2)3–N+–(CH3)2C18H37]Cl2(C18-3-18),作为介孔模板剂用于水热法合成介孔ZSM-5分子筛.结果表明,在130 oC低温晶化即可高效合成介孔ZSM-5分子刷.C18-3-18的加入量可影响到所合成介孔ZSM-5分子筛的相对结晶度和织构性质,它的形成遵从一个转晶过程.在合成初期,凝胶中介孔模板剂C18-3-18的使用导向了介孔材料的生成;随后在TPABr的模板作用下,介孔材料慢慢转晶生成具有MFI结构的介孔ZSM-5;然后所合成的介孔ZSM-5晶粒进一步长大并聚集形成块状颗粒,同时产生晶间介孔.C18-3-18作为介孔导向剂不仅可用于合成介孔ZSM-5分子筛,也可用于其它介孔分子筛的合成中.     

放射孔二氧化硅及其核壳结构的制备与表征

室温下以十六烷基三甲基溴化铵(CTAB)为模板剂, 正硅酸乙酯(TEOS)为硅源, 氨水(质量分数25%)为催化剂, 在水-乙醇-乙醚作共溶剂的体系中以氨基化的实心二氧化硅(NH₂-sSiO₂)为添加剂, 制备了放射孔二氧化硅及其核壳结构(sSiO₂@rSiO₂). 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、小角X射线衍射(XRD)、氮气吸附-脱附实验和孔径分布测定对其进行了表征和分析. 结果表明, 合成的产物为0.4~1 μm的球形粒子, 球上存在多级放射状孔道结构, 孔径从3 nm到几十纳米的多级孔径并存, 样品的Brunauer-Emmett-Teller(BET)比表面积为996 m²/g. 最后对放射孔二氧化硅的形成机理及核壳结构的影响因素进行了初步探讨.     

Silica nanobottles templated from functional polymer spheres

Nanosized hollow silica spheres with holes in the wall (denoted as silica nanobottles) have been successfully prepared by assembly of functional polymer nanospheres with tetraethoxysilane (TEOS) through hydrothermal methods, coupled with removal of the core by programmed calcination. The functional polymer nanospheres were obtained by emulsifier-free emulsion copolymerization of styrene and (ar-vinylbenzyl) trimethylammoium chloride. The silica nanobottle sample was characterized by thermogravimetric analysis (TG), differential thermal analysis (DTA), transmission electron microscopy (TEM), and nitrogen adsorption techniques. The above characterizations confirm that the silica nanobottles have holes of about 8 nm in the wall and this unique structural feature might be useful for their encapsulation. Furthermore, characterization by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and UV-visible absorption (UV-vis) showed that the luminescent material Eu(TTA)(3)(TPPO)(2) could be effectively encapsulated in silica nanobottles. This reveals that silica nanobottles have potential applications for nanotechniques.     

Sonochemical synthesis of hollow PbS nanospheres

PbS hollow nanospheres with diameters of 80-250 nm have been synthesized by a surfactant-assisted sonochemical route. The nanostructures were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), (high-resolution) transmission electron microscopy [(HR)TEM], and scanning electron microscopy (SEM) images. Structural characterization indicates that shells of the hollow spheres are composed of PbS nanoparticles with diameters of about 12 nm. The formation of the hollow nanostructure was explained by a vesicle-template mechanism, in which sonication and surfactant play important roles. Furthermore, uniform silica layers were successfully coated onto the hollow spheres via a modified St?ber method to enhance their performance for promising applications.     

以卵磷脂为手性添加剂制备手性介孔二氧化硅

以十六烷基三甲基溴化铵(CTAB)的自组装体为模板,卵磷脂(PC)为手性添加剂,在n_PC:n_CTAB=1:21时,通过溶胶-凝胶法制备了螺旋介孔二氧化硅纳米棒。利用扫描电镜(FESEM)、透射电镜(TEM)、X-射线衍射以及氮气吸附-脱附等测试手段,对该纳米棒的形貌以及孔结构进行了表征。TEM显示该纳米棒的长度约为50~200nm,直径约为30~50nm。X-射线衍射表明孔道呈二维六方排列,虽然FESEM显示纳米棒左右手比例约为1:1,但通过圆二色谱表征证明该纳米棒在埃尺度下倾向于形成单一手性。结果表明,卵磷脂的手性可以传递到螺旋介孔二氧化硅纳米棒中。     

以卵磷脂为手性添加剂制备手性介孔二氧化硅

以十六烷基三甲基溴化铵(CTAB)的自组装体为模板,卵磷脂(PC)为手性添加剂,在n PC∶nCTAB=1∶21时,通过溶胶-凝胶法制备了螺旋介孔二氧化硅纳米棒。利用扫描电镜(FESEM)、透射电镜(TEM)、X-射线衍射以及氮气吸附-脱附等测试手段,对该纳米棒的形貌以及孔结构进行了表征。TEM显示该纳米棒的长度约为50～200 nm,直径约为30～50 nm。X-射线衍射表明孔道呈二维六方排列,虽然FESEM显示纳米棒左右手比例约为1∶1,但通过圆二色谱表征证明该纳米棒在埃尺度下倾向于形成单一手性。结果表明,卵磷脂的手性可以传递到螺旋介孔二氧化硅纳米棒中。     

Synthesis of ordered mesoporous silica membrane on inorganic hollow fiber

This paper reports on a new method for the preparation of mesoporous silica membranes on alumina hollow fibers. A surfactant-silica sol is filled in the lumen of an alpha-alumina hollow fiber. The filtration technique combined with an evaporation-induced self-assembly (EISA) process results in the formation of a continuous ordered mesoporous silica layer on the outer side of alpha-alumina hollow fibers. X-ray diffraction (XRD), transmission electron microscopy (TEM), and nitrogen isothermal adsorption measurements reveal that these membranes possess hexagonal (P6mm) mesostructures with pore diameters of 4.48 nm and BET surfaces of 492.3 m(2) g(-1). Scanning electron microscopy (SEM) studies show that the layers are defect free and energy-dispersive spectroscopy (EDS) mapping images further confirm the formation of continuous mesoporous silica layer on the outer side of alpha-alumina hollow fibers. Nitrogen and hydrogen permeance tests show that the membranes are defect free.     

自组装水热合成碳点-中空氧化硅纳米粒复合材料

利用反相微乳液体系制备出粒径均一的中空氧化硅纳米粒(SHN),以此为基础,再利用水热法通过自组装合成了碳点-中空氧化硅纳米粒复合材料(CD-SHN)。 采用高分辨透射电子显微镜(HRTEM)和场发射扫描电子显微镜(FESEM)对其结构进行了表征,结果显示SHN尺寸为30~40 nm,壳厚约为10 nm,在此基础上合成出具有和海葵类似结构的CD-SHN,尺寸约为1 μm,并且,在水相中具有良好的分散性。 海葵状CD-SHN既具有激发波长依赖的多色荧光发射性能,又具有良好的光稳定性,其最大激发及发射波长分别位于360和435 nm附近,经40 W白炽灯照射60 min,其荧光强度仍可保持97%。 该材料的制备过程条件温和,其原材料生物相容性良好,在生物造影方面具有潜在的优势。     

Preparation and characterization of composites built of poly(N-benzophenoyl methacrylamide-co-N-hydroxyethyl acrylamide) cores and silica raspberry-like shells with dual orthogonal functionality

The design and fabrication of novel poly(N-benzophenoyl methacrylamide-co-N-hydroxyethyl acrylamide)@SiO(2) composites are reported herein. These core-shell composites demonstrate orthogonal functionality, composed of photoreactive cores, containing a benzophenone (BPh) moiety and silica (SiO(2)) shells, enabling the utilization of the free hydroxyl groups via silane-based chemistry. The co-polymer cores, which are 1.28μm in diameter, are first obtained by dispersion polymerization of photoreactive (N-benzophenoyl methacrylamide) (polyBPMA) and N-Hydroxyethyl acrylamide (HEAA). Next, silica seeds with a 42nm diameter are deposited onto the surfaces as a result of the hydrolysis and the condensation of tetraethyl orthosilicate (TEOS) in a basic condition. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), UV-spectrophotometry, X-ray photoelectron spectroscopy (XPS), and ζ-potential measurements were used to characterize the composites. The morphology and surface smoothness of the deposited silica nanoparticles (NPs) were found to strongly depend on a number of parameters such as the pH value of the medium, TEOS concentration, and the temperature.     

Synthesis, amino-functionalization of mesoporous silica and its adsorption of Cr(VI)

Mesoporous silica materials with a centered rectangular symmetry (cmm) have been synthesized through a facile direct-templating method using tetraethylorthosilicate (TEOS) and amphiphilic block co-polymers Pluronic P123 under acidic conditions. The amino groups have been grafted to as-synthesized mesoporous silica by [1-(2-amino-ethyl)-3-aminopropyl]trimethoxysilane (AAPTS). Thus obtained amino-functionalized mesoporous silica (denoted as NN-silica) was used for sequestration of Cr(VI) from aqueous solution. After sequestration of Cr(VI), the sample was denoted as Cr(VI)-silica. The parent mesoporous silica, NN-silica and Cr(VI)-silica were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and N(2) adsorption-desorption isotherms. XRD and TEM results confirm that the structure of these samples is centered rectangular symmetry (cmm). N(2) adsorption-desorption isotherms show that there is a remarkable decrease in surface area and pore volume for NN-silica (S(BET)=54.5 m(2)g(-1), V(P)=0.09 cm(3)g(-1)) and Cr(VI)-silica (S(BET)=53.2 m(2)g(-1), V(P)=0.07 cm(3)g(-1)) compared to the parent mesoporous silica (S(BET)=444.0 m(2)g(-1), V(P)=0.71 cm(3)g(-1)). The BJH desorption average diameter of NN-silica, Cr(VI)-silica and the parent mesoporous silica is 4.40 nm, 4.07 nm and 5.11 nm, respectively. The results reveal the channels of as-synthesized mesoporous silica are essentially grafted with abundant amino groups and loaded with Cr(VI). The adsorption experiment results show that the functionalized mesoporous silica materials possess an increased Cr(VI) adsorption capacity and the maximum Cr(VI) loadings at 25, 35 and 45 degrees C can reach 2.28, 2.86 and 3.32 mmol/g, respectively.