溶胶凝胶法制备超疏水二氧化硅涂膜及其表面润湿行为

采用溶胶-凝胶法以正硅酸乙酯(TEOS)和甲基三乙氧基硅烷(MTES)为前驱体制备超疏水SiO2涂层。红外光谱(FTIR)和热重分析(TGA)表征合成SiO2的化学组成,通过透射电镜(TEM)和扫描电镜(TEM)观察制备SiO2的结构形貌,扫描电镜(SEM)和原子力显微镜(AFM)观察SiO2涂膜的表面形貌,通过测试水接触角(WCA)讨论SiO2涂层的表面微观结构与其表面疏水性能的关系。结果表明以TEOS和MTES为共前驱体可以制备得到表面带-CH3基团的SiO2溶胶,SiO2溶胶在老化过程中纳米SiO2粒子由于自组装作用形成草莓状微米-纳米双微观结构,这种结构赋予SiO2涂膜表面不同等级的粗糙度,使得水滴与涂膜表面接触时能够形成高的空气捕捉率和较小的粗糙度因子,与SiO2表面疏水性的-CH3基团共同作用形成类荷叶超疏水结构。     

Formation of Superhydrophobic-Superhydrophilic Pattern on Flowerlike Alumina Thin Film by the Sol-Gel Method

We have prepared superhydrophobic surfaces which become superhydrophilic by heat-treatment at 500°C or irradiation of UV-light. When hydrolyzed fluoroalkyltrimethoxysilane (FAS) was coated on Al₂O₃ gel film with a roughness of 20 to 50 nm, the films showed superhydrophobicity and high transparency; the contact angle for water of the film was 165° and the transmittance for the visible light was higher than 92%. When the FAS-coated thin films were heat-treated at temperatures higher than 500°C, the films became superhydrophilic; the contact angle for water on the films was smaller than 5°. Thin films of amorphous TiO₂ or anatase TiO₂ were coated between Al₂O₃ gel and FAS layer, and the contact angle for water was also about 160°. UV irradiation using high-pressure mercury lamp on these films resulted in the contact angle to be smaller than 5°. When UV light was irradiated through a photomask, superhydrophobic-superhydrophilic micropatterns applicable as a stamper for printing or a substrate of micro-optical components were successfully obtained on the films.     

Formation of Anatase Nanocrystals-Precipitated Silica Coatings on Plastic Substrates by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals-precipitated silica coatings were formed on plastic substrates such as poly(ethylene terephtalate) (PET), acrylic resin (AC) and polycarbonate (PC) from silica-titania gel coatings with and without addition of poly(ethylene glycol) (PEG) by hot water treatment. The maximum thickness of the coatings which can be formed without cracking or peeling-off was 100 to 200 nm for PET and PC substrates, whereas it was less than 50 nm for AC substrates. After a hot water treatment at 90°C for 120 min, the size of the anatase nanocrystals increased to be 30 and 50 nm for the coatings obtained with and without PEG, respectively. Anatase nanocrystals were formed throughout the whole of the coatings obtained with PEG and were formed only on the surface of the coatings obtained without PEG. Both coatings obtained with and without PEG were highly transparent. The plastic substrates with coatings obtained without PEG showed good weathering resistance owing to the protective effects of the residual silica under-layer. The coatings obtained with PEG showed higher photocatalytic activities than those obtained without PEG due to smaller size and higher dispersion of anatase nanocrystals in the coatings.     

Inhibition of Pb-Leaching from Lead Crystal Glass by Coating with Films Prepared by the Sol-Gel Method

The chemical durability of lead glass tumblers (24% PbO) in a 4% (v/v) acetic acid solution before and after coating with sol-gel derived SiO2 films was assessed to determine the extent of reduction in Pb-leaching that can be achieved. It was found that by coating the internal surface of the glass tumblers with 1 ml of 10% TEOS solutions at 100°C and densifying the coating formed at 500°C for 1 h, it was possible to reduce Pb-leaching to about one quarter of that of the uncoated glass.     

Sol-Gel Preparation of Photocatalytic TiO2 Films on Polymer Substrates

Sol-gel TiO₂ thin films were autoclaved under various water/ethanol atmospheres. The microstructural, morphological and photocatalytic properties of the films were studied. The photocatalytic activity of the films appears closely related to crystallization states. It is shown that nanocrystallized porous films can be produced in a temperature range compatible with titania deposition on polymer materials. Consequently, photocatalytic films could successfully be prepared on polycarbonate and polymethylmetacrylate substrates. The autoclaved film properties are described and discussed with respect to sol-gel parameters and autoclaving conditions.     

Photocatalytic Decomposition of Acetaldehyde with Anatase Nanocrystals-Dispersed Silica Films Prepared by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals of 5 to 10 nm in diameter were formed in the silica-titania films by treatment with hot water. The formation of nanocrystals with hot water treatment was a unique phenomenon to the silica-titania system and the addition of organic polymers such as PEG was indispensable for the high dispersion of anatase nanocrystals in the films. The hydrolysis of Si—O—Ti bonds with hot water was considered to play an important role for the formation of anatase nanocrystals. The resultant films were transparent even after the formation of anatase nanocrystals. Acetaldehyde was photocatalytically decomposed into CO₂ on the films which were subjected to a hot water treatment. The amounts of generated CO₂ were twice of that of introduced acetaldehyde, indicating that the total acetaldehyde was completely decomposed to CO₂. Anatase nanocrystals-dispersed films can be formed on various kinds of substrates including those with poor heat resistance such as organic polymers and organisms by this process, so that the substrates coated with the films are expected to be widely used for photocatalytic applications.     

过滤成膜制备氧化铝中空纤维超滤膜

 介绍了在α－Al2O3中空纤维微滤膜上采用过滤成膜技术制备γ－Al2O3超滤膜的方法．应用热重分析、差热分析、X射线衍射和扫描电子显微镜等测试手段对膜的热稳定性、结构及形貌进行了表征．扫描电子显微镜结果表明，采用过滤成膜方式制备的担载中空纤维超滤膜表面无针孔，无裂纹．气体渗透实验进一步表明，所得中空纤维超滤膜完整、无缺陷，具有一定的气体选择性．经700℃焙烧后的膜在0．3和0．4MPa条件下对氮／氩的分离因子分别为1．133和1．139，说明气体通过膜的扩散以Knudsen扩散传质为主．用等温氮气吸附实验测定了非担载膜的孔径大小和分布，其比表面积为228．9m2／g，最可几孔径约为4．5nm．     

Preparation of Super-Water-Repellent Fluorinated Inorganic-Organic Coating Films on Nylon 66 by the Sol-Gel Method Using Microphase Separation

We have prepared super-water-repellent fluorinated inorganic-organic coating films on nylon 66 substrate from poly(methyl methacrylate) (PMMA), tetraethoxysilane (TEOS), and 2-perfluorooctylethyltriethoxysilane (17F) by the sol-gel method. The contact angle for water of the film was 149°. The fluorinated inorganic-organic film including PMMA particles exhibits the super-water-repellence on nylon 66 and the high ultrasonics-resistance in spite of the low 17F content of the molar ratio of 0.001 per mol of TEOS. The surfaces of the films were characterized by using XPS and SEM in combination with the surface roughness data. It was considered that the fluorinated component was segregated to form separated microphase regions, appropriate surface roughness being resulted to develop high water-repellence.     

Evaluation of Photocatalytic Activity of Transparent Anatase Nanocrystals-Dispersed Silica Films Prepared by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals were precipitated mainly at the surface of the silica-titania gel films with hot water treatment, whereas the addition of poly(ethylene glycol) (PEG) in the films led to the dispersion of anatase nanocrystals in the whole of the films after the treatment. Both films with and without PEG showed high photocatalytic activities for acetaldehyde, NO _x and stearic acid in the gas-solid system, and for methylene blue and potassium iodide in the liquid-solid system. The addition of PEG improved the photocatalytic activities of the resultant films due to the smaller anatase crystallites and the porous film structure. The residual silica under-layer of the superficially anatase-precipitated films is expected to act as a protective one for an organic polymer substrate against the photocatalytic degradation.     

位错对阳极氧化铝多孔薄膜纳米孔阵列结构的影响

多孔铝氧化物薄膜;电解质强度;位错对阳极氧化铝多孔薄膜纳米孔阵列结构的影响     

Epitaxially Grown LaSrCoO3 Thin Films on Various Substrates by the Sol-Gel Method

LaSrCoO₃ thin films have been prepared on various substrates by the sol-gel method using inorganic salts as starting materials. The crystallinity and in-plane alignment of the films were analyzed by X-ray diffraction -2 scans and scans (pole-figure analysis), respectively. Highly (h00)/(00l)-oriented LaSrCoO₃ films with crack-free surfaces were obtained by annealing at 800°C on SrTiO₃(100), while films grown on MgO(100) and Si(100) exhibited poor crystallinity. According to the X-ray diffraction -2 scan, crystallinity of the product films was found to depend on lattice-misfit values between the films and the substrates used. On the contrary, the lattice-misfit values were less effective to the epitaxy of the LSCO film. Epitaxial film grown on SrTiO₃ annealed at 800°C was found by reciprocal-space mapping (-2 scan) analysis to consist of the pseudocubic phase.     

Novel Protonic Conductive Silicates Produced by the Sol-Gel Method

ABSTRACT

Materials which display ionic conductivity were produced by the sol-gel and microemulsion-gel methods. The charging and discharging characteristics were investigated and it was found that a single ionic species was responsible for the conduction, the ionic species being residual protons from the initial component mixture. The complex impedence of various samples was measured and the ionic conductivities ranged in value from 9 × 10^?8 to 1 × 10^?5 ohm^?1 cm^?1. An Arrhemius plot for a microemulsion-gel revealed that the energy of activation was 0.15 eV.     

超疏水涂层表面粗糙结构对防覆冰性能的影响

结冰给交通、电力输送和航空等领域带来极大的安全隐患,研究防覆冰技术具有重要的应用价值。目前最具前景的防冰方法是涂层防冰,本文介绍了疏水涂层的构建方法,阐述了涂层疏水性和疏冰性之间的关系;重点论证了涂层表面粗糙结构对其防覆冰性能的影响,指出防覆冰涂层研发中存在的问题,并对该领域的发展趋势进行了分析和展望。     

Synthesis of New Hybrid Organic-Inorganic Alumina Gels by the Sol-Gel Method

New hybrid organic-inorganic alumina gels have been prepared by reacting aluminum sec-butoxide and propane-1,2-diol, in CCl₄ as solvent. This reaction occurred without water addition and without the use of any catalyst, leading to the formation of transparent and monolithic gels. IR,²⁷Al and¹³CNMR show that an interchange reaction between OBu ^s alkoxide groups and diol groups occurred, leading to the hybrid gels. Samples heat treated at different temperatures under argon are weakly porous and have a small specific surface area. XRD indicates the presence of pure α-alumina at 1450°C.     

聚合物熔体膜在基体表面的润湿和铺展行为

聚合物熔体膜在基体表面上的润湿和铺展行为受铺展系数和Hamaker常数影响。对于不能在基体表面上铺展的聚合物膜,当处于其玻璃化温度以上时,聚合物熔体膜将破裂,出现非连续区域。随着体系处于聚合物玻璃化温度以上时间的延长,非连续部分尺寸不断增长,增长速率与表面张力、聚合物粘度、聚合物液滴在基体表面的平衡接触角等因素有关,平衡后聚合物以液滴的形式在基体表面稳定存在。将带功能端基聚合物加入不能在基体表面上铺展的聚合物中,通过修饰聚合物与基体界面或改变聚合物熔体膜的表面张力,可以使原来不能在基体表面铺展的聚合物保持稳定。本文综述了聚合物熔体膜的铺展和润湿动力学研究进展,并归纳了使聚合物熔体膜稳定的方法。     

Formation of Anatase Nanocrystals in Sol-Gel Derived TiO2-SiO2 Thin Films with Hot Water Treatment

We have successfully prepared transparent and porous anatase nanocrystals-dispersed films by treating the sol-gel derived TiO₂-SiO₂ films containing poly(ethylene glycol), PEG, with hot water. This process was done at temperatures lower than 100°C under atmospheric pressure, and thus anatase nanocrystals-dispersed films can be formed on various kinds of substrates including organic polymers with poor heat resistance. The changes in structure and composition of the TiO₂-SiO₂ gel films with hot water treatment were related to the formation process of anatase nanocrystals in the TiO₂-SiO₂ gel films with hot water treatment. The formation of anatase nanocrystals was found to proceed to hydrolysis of Si–O–Ti bonds and dissolution of SiO₂ component. In addition, porous film structure formed by leaching of PEG with hot water treatment led to homogenous dispersion of anatase nonocrystals in the films.     

Anti-Reflective Coatings of Flowerlike Alumina on Various Glass Substrates by the Sol–Gel Process with the Hot Water Treatment

Anti-reflective (AR) properties of flowerlike alumina thin films with a small roughness of less than 100 nm have been studied on substrates such as soda-lime silica glass, non-alkali glass, and quartz glass. The highest AR effects were obtained on quartz glass substrate, which has the lowest refractive index of the three substrates. The reflectance of quartz glass substrates coated with flowerlike Al₂O₃ was less than 0.5% in the wavelength region from 300 to 720 nm.     

Preparation and Characterization of MgO Thin Films by a Novel Sol-Gel Method

MgO thin films have been prepared on Si substrates by a novel and simple sol-gel method using magnesium nitrate and collodion as starting material. Solutions consisting of magnesium nitrate in a mixture of collodion and ethanol were spin-coated onto silicon substrates. It was found that collodion was a necessary component to form stable sols and the crystallization and structures were clearly dependent on the amount of the collodion and the annealing temperature. The MgO thin films with good crystallization were obtained after annealing at 800°C. Meanwhile, the microstructure of the MgO films was examined by transmission electron microscopy and atomic force microscopy.     

Preparation,Characteristics, and Photocatalytic Tests of Fe-Doped TiO2 Films Prepared by a Sol-Gel Drain Coating via Homemade Devices

Anatase Fe-doped TiO₂ films, with the rang of iron to titanium (Fe(NO₃)₃ · 9H₂O:Ti(OC₄H₉)₄)) atomic ratios (R _Fe/Ti ) from nominal 0 to 20%, are prepared by a sol-gel drain coating via homemade devices, and the hydrolysis reaction to derive sol is suppressed by adding an new agglomerating agent acetylacetic ether (EAcAc) to the system. The films are characterized by using thermogravimetry and differential thermal analysis (TG-DTA), x-ray diffraction (XRD), ultraviolet (UV)–visible absorbance spectra (UV–vis), and scanning electron microscope (SEM), together with energy-dispersive x-ray spectroscopy (EDX). Furthermore, the photocatalytic activities are measured by photodegrading rhodamine B (RhB) in a cylindrical Pyrex reactor, the experimental details demonstrate that the Fe-doped TiO₂ films (R _Fe/Ti  = 3.0%) show the most excellent photocatalytic perfomances, which is good accordance with UV-vis spectra.     

Coating of Methyltriethoxysilane—Modified Colloidal Silica on Polymer Substrates for Abrasion Resistance

Organic-inorganic hybrid composites were prepared by the sol-gel method for the hard coating agent of transparent plastic, and their abrasion resistance, optical and surface characteristics were evaluated. Methyltriethoxy-silane (MTES) and colloidal silica were used as starting materials. The addition of MTES to colloidal silica enabled the formation of dense thin films with very smooth surface on the substrates. The thin films were strongly adhered to the substrates without primer treatment. The abrasion resistance increased with the increase in the ratio of MTES to the colloidal silica. Optimal amount of MTES for the hard coating agent was 100 wt% to the colloidal silica. The addition of curing catalyst, tetramethylammonium formate was found to be very effective to enhance the adhesion strength of coating agent to the substrates and reduced curing time.