Flow-injection spectrophotometric determination of enalapril in pharmaceuticals with bromothymol blue

Enalapril (1.5–60 μ gl^?1) in aqueous solution is extracted into dichloromethane as its ion-pair with bromothymol blue in an unsegmented flow system and quantified spectrophotometrically. Up to 80 samples h^?1 can be processed, with r.s.d. of 1.0–3.4%. The degradation products of enalapril and excipients in the pharmaceutical dosage form do not interfere.     

Flow-injection spectrophotometric determination of arylamines and sulphonamides by diazotization and coupling in a micellar medium

In a sodium dodecyl sulphate (SDS) micellar solution, the rate of coupling of a diazonium ion with N-(1- naphthyl)ethylenediamine (NED) increases greatly, the protonation of the resulting azo dyes takes place at higher pH values and the dyes are more soluble. These favourable features were applied to the development of a simple flow-injection spectrophotometric procedure for the determination of diazotizable substances of pharmaceutical interest. Limits of detection in the range 0.2–0.5 μg ml^?1 (signal-to-noise ratio=3), with relative standard deviation of 0.7–3% (n=3) for 5 μg ml^?1 standards, were obtained.     

Flow-injection spectrophotometric determination of sulfadiazine and sulfamethoxazole in pharmaceuticals and urine.

A rapid and sensitive flow-injection spectrophotometric method is proposed for the determination of sulfadiazine and sulfamethoxazole. This method is based on the diazotization of sulfonamide with sodium nitrite, and a coupling reaction of the diazo-compound with alpha-naphthylamine. The optimum experimental conditions are obtained by using the controlled and weighted centroid simplex method. The linear ranges for the determination of sulfadiazine and sulfamethoxazole are 0.2-20 microg ml(-1) and 0.1-20 microg ml(-1), and their detection limits are 0.06 microg ml(-1) and 0.05 microg ml(-1), respectively, and the sampling frequency is 130 samples per hour. The method has been used to determine sulfadiazine and sulfamethoxazole in pharmaceuticals and urine without separation. The results are in agreement with those obtained by a high-performance liquid chromatograph technique at the 95% confidence level.     

Non-extractive derivative spectrophotometric determination of cobalt in neutral micellar medium

A sensitive derivative spectrophotometric method using 1-nitroso-2-naphthol has been developed for determination of trace amounts of cobalt in the presence of a neutral surfactant. Photometric parameters, viz., lambda(max), molar absorption coefficient and analytical sensitivity of the complex formed in micellar media are 420 nm, 3.18x10(4) l mol(-1) cm(-1) and 2.05 ng ml(-1), respectively. Beer's law holds from 0.20 to 3.0 mug ml(-1) of the analyte concentration. The method has a high sensitivity with a detection limit of 1.68 ng ml(-1). A selective determination of cobalt in presence of copper(II) or iron(III) using derivative spectral profiles and without any masking or pre-separation is also reported. Samples of drugs and standard alloys analysed by the proposed method yielded results comparable to those obtained using recommended procedures.     

Kinetic spectrophotometric determination of traces of sulfide in nonionic micellar medium

A sensitive kinetic spectrophotometric method for the determination of ng amounts of sulfide has been developed based on the reduction of Azure A by sulfide in the presence of Brij-35 at pH 7. The decrease in absorbance of Azure A at 600 nm is proportional to the concentration of sulfide over the range 25–1400 ng mL^–1. The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 17 ng mL^–1, and the relative standard deviation of seven determinations of 500 ng mL^–1 sulfide was 2.1%. The method was applied to the determination of sulfide in spring water.     

Flow-injection fluorimetric determination of menadione using on-line photo-reduction in micellar media

A very sensitive fluorimetric method for the determination of menadione using a flow injection system is proposed. The method is based on the on-line reduction of menadione in dodecylsulphate micelles upon irradiation with UV light. The strong fluorescence of the reduced menadione in micellar medium is measured at 410 nm with excitation at 340 nm. The method shows a linear range between 2.42 and 245 ng ml⁻¹ and a limit of detection of 0.18 ng ml⁻¹. The sample throughput was 90 injections per hour. The applicability of the assay was demonstrated by analysing this vitamin in commercial pharmaceutical preparations.     

Kinetic spectrophotometric determination of traces of sulfide in nonionic micellar medium

A sensitive kinetic spectrophotometric method for the determination of ng amounts of sulfide has been developed based on the reduction of Azure A by sulfide in the presence of Brij-35 at pH 7. The decrease in absorbance of Azure A at 600 nm is proportional to the concentration of sulfide over the range 25-1,400 ng mL(-1). The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 17 ng mL(-1), and the relative standard deviation of seven determinations of 500 ng mL(-1) sulfide was 2.1%. The method was applied to the determination of sulfide in spring water.     

Simultaneous derivative spectrophotometric determination of thorium and uranium in a micellar medium

Derivative photometric methods for trace analysis of Th(IV) and UO₂(II), and their simultaneous determination in mixtures using 5,8-dihydroxy-1,4-naphthoquinone in a micellar medium are reported. Molar absorptivity and Sandell's sensitivity of 1:2 Th(IV) and 1:1 UO₂(II) complexes at their λ_max, 614.5 nm and 637.0 nm are, 1.19 × 10⁴ 1/mol/cm and 1.12 × 10⁴ 1/mol/cm and 1.95 × 10⁻² μg/cm² and 2.13 × 10⁻² μg/cm² μg/cm², respectively. Calibration graph is linear over the range 9.28 × 10⁻²−18.56 μg/ml of Th(IV) and 9.52 × 10⁻²−19.04 μg/ml of UO₂(II). Though presence of Th(IV) and UO₂(II) causes interference in each others determination, 9.28 × 10⁻¹−9.28 μg/ml Th(IV) and 9.52 × 10⁻¹−9.52 μg/ml UO₂(II) when present together, can be simultaneously determined using derivative spectra.     

Derivative spectrophotometric determination of copper(II) in non-ionic micellar medium

A photometric method for trace analysis of Cu(II) with 1-(2-pyridylazo)-2-naphthol (PAN) in presence of a neutral surfactant, Triton X-100, has been reported in normal and derivative modes. The molar absorption coefficient () and Sandell's sensitivity (S) of PAN-Cu(II) complex at 555 nm is 5.21 x 10(4) l mol(-1) cm(-1) and 1.22 ng cm(-2) respectively. The detection limit of Cu(II) is 4.0 ng ml(-1) and Beer's law is obeyed in the range 0.08-4.00 mug ml(-1) of the analyte. Copper content of a number of commercially available alcoholic beverages, biological and standard alloy samples is reported. The results obtained are in excellent agreement with those obtained using AAS.     

Flow-injection spectrophotometric determination of methyldopa in pharmaceutical formulations

A flow-injection spectrophotometric procedure is proposed for methyldopa determination in pharmaceutical preparations. The determination is based on formation of a yellow product (measured at 410 nm) after complexation of methyldopa with molybdate. Under optimal conditions, Beer's law is obeyed in a concentration range of 50-200 mg l⁻¹ methyldopa. Typical correlation between absorbance and analyte concentration was 0.9999. Usual excipients used as additives in pharmaceuticals do not interfere with the proposed method. The analytical frequency was 210 h⁻¹ and the relative standard deviation (R.S.D.) was ≤2% for sample solution containing 150 mg l⁻¹ methyldopa (n = 11). The analytical results obtained in commercial formulations by applying the proposed FIA method were in good agreement with labeled values and those obtained by the Brazilian Pharmacopoeia procedure at 95% confidence level.     

Flow-injection spectrophotometric determination of calcium using murexide as a color agent

FI spectrophotometric determination of calcium using murexide has been developed. The problem of the color of the dye fading and/or its complex in an alkaline medium in the batch method can be overcome by taking advantage of FIA. A calcium solution is injected into an ethylenediamine–ethylenediamine hydrochloride buffer (1 M, pH 11) which also serves as a masking agent, and is then merged with the aqueous murexide (0.005%, w/v) and continuously monitored. Simple FIA manifolds, including an LED colorimeter detector hooked up to a PC-based data acquisition and evaluation system are described. Optimization of FIA systems has been made. The proposed procedures have been validated by using reference materials and comparing the results with the standard methods, and then applied to ores and drug samples.     

流动注射化学发光法测定头孢氨苄和头孢拉定

基于KMnO4在酸性介质中氧化头孢氨苄和头孢拉定产生微弱的化学发光,同时借助甲醛对发光的增强作用,采用流动注射技术,建立了以上两种头孢类抗生素药物的测定新方法。方法检出限分别为0.096和0.10μg mL;相对标准偏差分别为1.6%和1.8%(n=11),线性范围分别为0.8～25和0.8～32μg mL,进样频率为60次 h。本方法已用于药物制剂的测定。     

Enhanced spectrophotometric determination of nicotinic acid in a sodium dodecyl sulphate micellar medium

The spectrophotometric determination of pyridine and pyridine derivatives by means of the K?nig reaction was studied in micellar media of sodium dodecyl sulphate (SDS), N-cetylpyridinium chloride and Triton X-100. The sensitivity was largely increased in SDS micellar medium. The attack of the pyridine ring with cyanogen bromide to produce a glutaconic aldehyde was not affected by the presence of SDS, but the yield of the coupling reaction with an arylamine to produce a polymethine dye was largely increased. In the SDS micellar medium, aniline was superior to other coupling reagents. The limits of detection (LODs) were 6 x 10(-7), 1 x 10(-6) and 5 x 10(-7)M for pyridine, pyrrol-ylmethylpyridine and nicotinic acid, respectively, and the reproducibility for 2 x 10(-5)M solutions was ca. 2%. In the absence of SDS, the LODs were 3 x 10(-6), 3 x 10(-6) and 9 x 10(-6)M, respectively, and the reproducibility was ca. 3.5%. Application was made to the determination of nicotinic acid in pharmaceuticals.     

Flow-injection ultraviolet spectrophotometric determination of sulphate in natural waters

The proposed method is based on measurement of the absorbance of the FeSO₄⁺ complex cation at 355 nm. Sample-injection and reagent-injection procedures are described. Calibration graphs are linear in the ranges 25–600 and 10–150 mg l^?1 sulphate, respectively. The main interference is from ultraviolet-absorbing organic compounds in the waters. Methods of eliminating the interference are discussed. Results for sulphate in river waters compare satisfactorily with those obtained by the gravimetric method. Depending on the pretreatment used, 10–30 samples can be analyzed per hour.     

Flow-injection amplification for the spectrophotometric determination of iodide

A flow manifold is described in which iodide (0.05–15 μg ml^?1) in a 50-μl sample is oxidized by bromine water to iodate, most of the excess of bromine is reduced by formic acid, and the iodate is reacted with more iodide to form triiodide, which is determined spectrophotometrically. Six-fold amplification is achieved. The relative standard deviation is ca. 1%).     

Flow-injection spectrophotometric determination of salbutamol with 4-aminoantipyrine

A flow-injection method is proposed for the determination of salbutamol. The method involves the condensation of salbutamol with 4-aminoantipyrine in the presence of hexacyanoferrate (III) in alkaline medium, producing a coloured quinoneimide that was detected absorptiometrically at 500 nm.

The values of four variables (two reactor lengths and two reagent concentrations) were optimised by means of the sequential simplex method and their influence studied in univariant way.

The method was validated and compared with the HPLC method established in the United States Pharmacopeia (USP). Linearity was demonstrated in the range 0–74.1 mg/L of salbutamol sulfate (r² = 0.9999). Commercial samples of pharmaceuticals containing salbutamol sulfate (tablets and oral solutions) were analysed and the results obtained with the proposed method agreed with the USP method in less than 1.6%, with precision similar to the HPLC method (1%–2% R.S.D.). The sampling frequency was 75 samples/hour.     

Flow-injection extraction-spectrophotometric determination of imipramine in pharmaceuticals with methyl orange

Imipramine in aqueous solution is extracted into 1,2-dichloroethane as its ion-pair with Methyl Orange in an unsegmented flow system and quantified spectrophotometrically. A linear calibration graph was obtained between 0.79 and 25.3 mug/ml of imipramine. Up to 45 samples/hr can be processed with a RSD of 0.88-1.6%. The method was satisfactorily applied to the determination of imipramine in pharmaceutical preparations.     

Mixed micellar medium for the spectrophotometric determination of molybdenum in molybdenum/tungsten mixtures

Effects of cetyltrimethylammonium bromide (CTAB) and/or nonylphenoxypolyethoxyethanol (OP) on the absorption spectra of the complexes of molybdenum and tungsten with bromopyrogallol red (BPR) were studied. Based on these effects, a mixture of CTAB and OP was thus selected as a medium for the selective and sensitive determination of Mo in Mo/W binary mixtures. Under the optimum conditions, Beer's law was obeyed over the range 0.06-0.8 mug ml(-1) Mo with molar absorptivity being 1.3x10(5) l mol(-1) cm(-1) and detection limit 0.025 mug ml(-1). For 1.0 mug Mo, at least 20 mug W did not interfere in the determination of Mo with average recovery and relative standard deviation being 99.5% and <2%, respectively. The method developed maintained the features of simplicity and rapidity and, moreover, its selectivity and sensitivity enhanced greatly due to the use of CTAB/OP mixed micellar medium. When coupled with a compatible concentration method, the proposed method could be used for the determination of trace Mo in natural waters.     

Flow-injection spectrophotometric determination of azithromycin in pharmaceutical formulations using p-chloranil in the presence of hydrogen peroxide.

A flow-injection (FI) spectrophotometric procedure exploiting merging zones is proposed for the determination of azithromycin in pharmaceutical formulations. The method is based on the reaction of azithromycin with tetrachloro-p-benzoquinone (p-chloranil) accelerated by hydrogen peroxide and conducted in a methanol medium, producing a purple-red color compound (lambda(max) = 540 nm). The FI system and the experimental conditions were optimized using a multivariate method. Beer's law is obeyed in a concentration range of 50 - 1600 microg mL(-1) with an excellent correlation coefficient (r = 0.9998). The detection limit and the quantification limit were 6.6 and 22.1 microg mL(-1), respectively. No interference was observed from the common excipients, and the recoveries were within 98.6 to 100.4%. The procedure was applied to the determination of azithromycin in pharmaceuticals with a high sampling rate (65 samples h(-1)). The results obtained by the proposed method were in good agreement with those obtained by the comparative method at 95% confidence level.     

A sensitive spectrophotometric determination of atrazine in micellar medium and its application in environmental samples

A sensitive analytical procedure based on solid phase extractive-spectrophotometry has been established for the determination of the widely used herbicide atrazine .The method is based on the Konig reaction in which atrazine reacts with pyridine reagent to form a quaternary pyridinium halide, which further forms glutaconic aldehyde in the presence of alkali. Glutaconic aldehyde is subsequently coupled with 4-aminoacetanilide in the micellar medium of anionic surfactant sodium dodecyl sulphate to give a yellow-orange dye. The produced dye was enriched on a C₁₈ cartridge and is measured spectrophotometrically at 460 nm. The sensitivity and selectivity of the method was largely enhanced in the micellar media and SPE on the C₁₈ cartridge and avoids the use of toxic solvents. Beer’s law was obeyed in the range 0.012–0.12 μg mL^?1. Molar absorptivity and Sandell’s sensitivity were found to be 1.52 × 10⁶ L mol^? 1 cm^?1 and 0.0002 μg cm^?2, respectively. The limit of detection and quantification were 0.001 and 0.003 μg mL^?1, respectively. The proposed method was applied successfully for the determination of atrazine in environmental and biological samples with a recovery range of 96–101 %. The method was found to be free from interference of a large number of foreign species. The accuracy and reliability of the method was further established by parallel determination by the reference method, and by recovery studies.