Nanostructured Bi(2-x)Cu(x)S3 bulk materials with enhanced thermoelectric performance

Nanostructured Bi(2-x)Cu(x)S(3) (x = 0, 0.002, 0.005, 0.007, 0.01, 0.03) thermoelectric polycrystals were fabricated by combining mechanical alloying (MA) and spark plasma sintering (SPS) methods. The effect of Cu content on the microstructure and thermoelectric property of Bi(2-x)Cu(x)S(3) bulk samples was investigated. It was found that the subtle tailoring of Cu content could reduce both the electrical resistivity and the thermal conductivity at the same time, and consequently enhancing the thermoelectric property. A low electrical resistivity of 1.34 × 10(-4)Ω m(-1) and a low thermal conductivity of 0.52 W m(-1) K(-1) were obtained for the Bi(1.995)Cu(0.005)S(3) sample at 573 K. The low thermal conductivity is supposed to be due to the nanoscopic Cu-rich regions embedded in the host matrix. A peak ZT value of 0.34 at 573 K was achieved for the Bi(1.995)Cu(0.005)S(3) composition, which is the highest value in the Bi(2)S(3) system reported so far.     

Study on the visible-light photocatalytic performance of Ag3PO4/Cu2O composite

Research on Chemical Intermediates - Ag3PO4/Cu2O composites were prepared by a facile wet chemical method. The specimens were examined by X-ray diffraction, scanning electron microscopy,...     

Electrochemical performance comparison of MWCNTs/Ni (OH)2 composite materials by two preparation routes

Journal of Solid State Electrochemistry - Carbon materials are used to improve the nickel hydroxide electrode capacity in rechargeable alkaline batteries. Herein, we present the preparation of...     

The Layered Coordination Polymer Bi(SCN)3·1/2H2O

Yellow crystals of Bi(SCN)₃·1/2H₂O are obtained by reacting (BiO)₂CO₃ and HSCN in aqueous solution. X‐ray diffraction on a single‐crystal revealed a triclinic lattice (space group P ) with a = 843.6(2) pm, b = 920.4 (2) pm, c = 1210.7(2) pm, α = 109.16(3) °, β = 109.06(3) °, γ = 90.22(3) °, V = 832.8(3)·10⁶ pm³, and Z = 4. All thiocyanate anions bind with both ends to different cations. The coordination network expands in plane layers parallel (1 0). The water molecule coordinates one of the two independent Bi³⁺ cations. Dehydration sets in at 100 °C, followed by stepwise thermal decomposition to Bi₂S₃.     

多壁碳纳米管负载Cu2O和CuI催化剂上芳醛与2-氨基吡啶氧化酰胺化反应：Cu（I）物种的催化作用

采用浸渍法制备了多壁碳纳米管(MWCNT)负载的Cu2O和CuI催化剂,并运用粉末X射线衍射、红外光谱、扫描电镜-能量散射谱、透射电镜和NH3程序升温脱附等技术对催化剂进行了表征。结果表明,催化剂中沉积的Cu2O和CuI分别以立方相和γ相存在于MWCNT上,且表现出由弱到强的拉电子(Lewis酸)性能。将催化剂用于催化芳醛与2-氨基吡啶氧化酰胺化反应合成N-(吡啶-2-基)苯酰胺类化合物,产物选择性为100%,收率为50%–95%。 CuI/MWCNT催化剂上产物分离收率性能好于Cu2O/MWCNT,但后者的循环使用性能更好。与共价的CuI相比,离子化的Cu2O与极性的酸活化的MWCNT间具有更适宜的相互作用,这种不同的相互作用可显著影响2-氨基吡啶的氨基对芳醛羰基的亲核进攻速率。     

Effect of pH value on the microstructure and deNO(x) catalytic performance of titanate nanotubes loaded CeO2

The relationship between catalytic performance and pH value of post-treatment of the catalyst supports-titanate materials was investigated and discussed. Three types of titanate nanotubes (TNTs) that are acidic TNTs (TNTs-1.6, pH value at 1.6), neutral TNTs (TNTs-7), and alkaline TNTs (TNTs-12) were synthesized by hydrothermal method with the controlled washing pH value and then were used as the catalyst supports for ceria. These titanate-supported ceria catalysts showed extremely different performance for the selective catalytic reduction in NO. The pH value had a notable effect on the structure and composition of titanate nanotubes and further affected the state and redox property of cerium oxides. The structure of TNTs-1.6, TNTs-7, and TNTs-12 were identified as anatase-like structure, protonated titanate (H(2)Ti(3)O(7)), and Na-containing titanate, respectively. Indeed, the residual sodium (TNTs-12) was harmful to ceria, but the presence of water in the interlayer (TNTs-7) was beneficial to the stability of nanotube structure. Therefore, TNTs-7 doped ceria showed the best SCR activity among these tested samples.     

The System Bi2O3–R2O3 (R=Y,Gd)

A new face centered cubic phase of composition Bi₃RO₆ (R?Y, Gd) is reported, and details of the Bi₂O₃–R₂O₃ (R?Y, Gd) phase diagrams are discussed. Similar compositions with R?Tb, Dy, Hc, Er are examined.     

Novel amino-functionalized Fe3O4/carboxylic multi-walled carbon nanotubes: One-pot synthesis,characterization and removal for Cu(II)

Russian Journal of Applied Chemistry - A novel amino functionalized Fe3O4/multi-walled carbon nanotubes hybrid was synthesized by a facile and efficient one-pot solvothermal process. The...     

Novel electromagnetic functionalized γ‐Fe2O3/polypyrrole composite nanostructures with high conductivity

In general, the conductivity of polypyrrole (PPy) is reduced by addition of magnetic nanoparticles as the additives owing to insulating effect of magnetic nanoparticles. In this article, novel electromagnetic functionalized PPy composite nanostructures were prepared by a template‐free method associated with γ‐Fe₂O₃ nano‐needles as the hard templates in the presence of p‐toluene‐sulfonic acid (p‐TSA) and FeCl₃·6H₂O as the dopant and oxidant, respectively. It was found that the molar ratio of γ‐Fe₂O₃ to pyrrole monomer represented by [γ‐Fe₂O₃]/[Py] ratio strongly affected the morphology and the conductivity of the γ‐Fe₂O₃/PPy composite nanostructures. A growth mechanism for the composite nanostructures was proposed based on the variance of the morphology with the [γ‐Fe₂O₃]/[Py] ratio. Compared with previously reported γ‐Fe₂O₃/PPy composites, the as‐prepared novel composite nanostructures showed much higher conductivity (up to ～50 times higher). Moreover, the synthesized γ‐Fe₂O₃/PPy composite nanostructures displayed ferromagnetic behavior with a high coercive force. Explanations for these interesting observations were made in terms of the magnetic interaction between ferromagnetic γ‐Fe₂O₃ nano‐needles and spin‐polaron of PPy nanotubes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4446–4453, 2009     

In situ preparation of Bi2O3/(BiO)2CO3 composite photocatalyst with enhanced visible-light photocatalytic activity

A Bi₂O₃/(BiO)₂CO₃ (BO/BOC) composite photocatalyst was in situ prepared via calcinating (BiO)₂CO₃. The as-prepared Bi₂O₃/(BiO)₂CO₃ composites displayed enhanced photocatalytic activity for the degradation of RhB under visible light. The structure–activity relationship between catalyst structure and properties was investigated by SEM, XRD, XPS, FTIR, BET, DRS and photoelectrochemical tests. Apart from the increased absorption of visible light, the accelerated charge separation and transfer was achieved via the intimate contact and matched band structure between Bi₂O₃ and (BiO)₂CO₃. The formation of heterogeneous structures could promote the production of reactive oxygen species (·O₂^?) and eventually improve the photocatalytic performance for the removal of organic contaminants. This heating treatment strategy might be extended for improving light absorbance and charge carriers separation for other UV-based photocatalysts.

     

Triethylphosphanimin-Komplexe der Acetate von Kupfer(II) und Zink. Kristallstrukturen von [Zn(O2C–CH3)2(HNPEt3)], [Cu5(O2C–CH3)10(HNPEt3)2] und [Cu(O2C–CH3)2(HNPEt3)2]

Triethylphosphanimine Complexes of the Acetates of Copper(II) and Zinc. Crystal Structures of [Zn(O₂C–CH₃)₂(HNPEt₃)], [Cu₅(O₂C–CH₃)₁₀(HNPEt₃)₂], and [Cu(O₂C–CH₃)₂(HNPEt₃)₂] The title compounds originate from the anhydrous acetates of zinc and copper(II) with trimethylsilyl-triethylphosphanimine, Me₃SiNPEt₃, in the presence of water in dichloromethane. They form colourless ( 1 ), bluish-green ( 2 ), and blue ( 3 ), respectively, single crystals, which were characterized by IR spectroscopy and by crystal structure analyses. [Zn(O₂C–CH₃)₂(HNPEt₃)] ( 1 ): Space group P 4 2₁c, Z = 8, lattice dimensions at –83 °C: a = b = 1709.6(2), c = 982.4(1) pm, R = 0.0551. 1 has a polymeric chain structure in which the zinc atoms are μ₂-bridged via the oxygen atoms of one of the two acetato groups, while the second acetato group and the phosphanimine are bonded terminally. [Cu₅(O₂C–CH₃)₁₀(HNPEt₃)₂]( 2 · 4 CH₂Cl₂): Space group P2₁/c, Z = 8, lattice dimensions at –80 °C: a = 1761.18(13), b = 4074.5(2), c = 1733.34(15) pm, β = 91.383(10)°, R = 0.0413. 2 consists of the two structural units [Cu₂(O₂C–CH₃)₄] and [Cu₃(O₂C–CH₃)₆(HNPEt₃)₂], which are connected via two of the acetato groups of the Cu₃-unit along the crystallographic a-axis to form three crystallographically independent polymeric strands. [Cu(O₂C–CH₃)₂(HNPEt₃)₂] ( 3 ): Space group P2₁/n, Z = 2, lattice dimensions at 20 °C: a = 695.49(8), b = 1217.85(10), c = 1380.05(7) pm, β = 96.451(7)°, R = 0.0291. 3 forms monomeric, centrosymmetric molecules with a square planar environment at the Cu atoms.     

由己二酸根桥联的新颖双U形四核铜配合物: [Cu4(phen)4(NO3)2(H2O)2(adip)4/4(Hadip)4/2](NO3)2•2H2O

邻菲罗啉、己二酸和硝酸铜在水溶液中反应得到一种新颖的四核铜配合物[Cu4(phen)4(NO3)2(H2O)2- (adip)4/4(Hadip)4/2](NO3)2•2H2O (其中H2adip＝己二酸), 并经元素分析, IR, UV, TG和X射线单晶衍射分析表征. 该配合物晶体属三斜晶系, 空间群, a＝1.0146(2) nm, b＝1.0261(2) nm, c＝1.8285(4) nm, α＝91.66(3)°, β＝92.19(3)°, γ＝112.76(3)°, V＝1.7520(6) nm3, Z＝1, Dc＝1.639 g/cm3, C66H66Cu4N12O28, Mr＝1729.47, F(000)＝886, μ＝1.294 mm－1, R1和wR2分别为0.0447和0.1141. 己二酸根通过4个羧基O将两个U形双核亚单元联接成具有一个对称中心的双U形四核结构, 其中每个U型亚单元包含晶体学上不对称的2个Cu(II)原子. 每个Cu(II)离子均处于畸变的四方锥配位环境, 除与己二酸氢根(Hadip)、己二酸根(adip)和邻菲罗啉(Phen)的N, O配位形成锥底平面外, 其中的1个Cu(II)与水配位, 而另一个Cu(II)则与硝酸根配位. 配合物晶体结构中存在着广泛的氢键和p×××p作用.     

A ternary phased SnO2-Fe2O3/SWCNTs nanocomposite as a high performance anode material for lithium ion batteries

A new SnO_2-Fe_2O_3/SWCNTs(single-walled carbon nanotubes) ternary nanocomposite was first synthesized by a facile hydrothermal approach.SnO_2 and Fe_2O_3 nanoparticles(NPs) were homogeneously located on the surface of SWCNTs,as confirmed by X-ray diffraction(XRD),transmission electron microscope(TEM) and energy dispersive X-ray spectroscopy(EDX).Due to the synergistic effect of different components,the as synthesized SnO_2-Fe_2O_3/SWCNTs composite as an anode material for lithium-ion batteries exhibited excellent electrochemical performance with a high capacity of 692 mAh·g~(-1) which could be maintained after 50 cycles at 200 mA·g~(-1).Even at a high rate of2000 mA·g~(-1),the capacity was still remained at 656 mAh·g~(-1).     

Multi-walled carbon nanotubes and Ru(bpy)3/nano-Au nano-sphere as efficient matrixes for a novel solid-state electrochemiluminescence sensor

An effective method for immobilization of Ru(bpy)₃²⁺ on glassy carbon electrode surface (GCE) is developed for the preparation of a novel electrochemiluminescence sensor. First of all, the positively charged Ru(bpy)₃²⁺ is modified on the surface of negatively charged gold nanoparticles (nano-Au) via the electrostatic interactions to obtain the Ru(bpy)₃²⁺/nano-Au nano-sphere (abbreviate as Ru-AuNPs). Subsequently, the large amount of Ru-AuNPs are immobilized on the multi-wall carbon nanotubes (MWCNTs)-Nafion homogeneous composite coated GCE by dual interaction: firstly, the Nafion, a kind of typical cation-exchange membrane, can absorb the Ru-AuNPs as the enrichment of cation Ru(bpy)₃²⁺ on the Ru-AuNPs surface; secondly, the employment of carboxylic MWCNTs in the Nafion film can also chemosorb the Ru(bpy)₃²⁺ cation on the Ru-AuNPs surface to increase the carrier content. At the same time, the experiment confirms that the enhancement of the ECL intensity on the sensor is attributed to following reasons. One hand, the employment of MWCNTs in the Nafion film enlarged the electro-active surface areas to benefit the contact between the signal probe on the composite film and coreactant used as reinforcing agent. On the other hand, the nano-materials of MWCNTs and nano-Au also improve the conductivity of the assembled film to increase the quantity of excited state of Ru(bpy)₃²⁺ in the unit time under the electrochemical condition and finally cause better properties in luminescence. In the experiment, the influence of the coreactant tripropylamine (TPA) on proposed ECL sensor is investigated. The logarithm of ECL intensity is proportional to the logarithm of TPA concentration on the range of 4 × 10⁻¹⁰ M to 2.8 × 10⁻⁶ M and 2.8 × 10⁻⁶ M to 0.71 × 10⁻³ M. After optimizing these conditions, the ECL sensor with TPA as coreactant is employed to detect a kind of alkaloid medicine, Matrine, for evaluating the practical application in the medicine analysis. The present sensor with TPA as coreactant shows the good response to the medicine concentration of the Matrine from 2.0 × 10⁻⁶ M to 6.0 × 10⁻³ M, which is used to detect the Matrine concentration in the Matrine injection.     

In(2)O(3) microbundles constructed with well-aligned single-crystalline nanorods: F127-directed self-assembly and enhanced gas sensing performance

Copper-succinate-layered hydroxide (CSLH), a new nanohybrid material, was synthesized as an inorganic-organic nanohybrid, in which organic moiety was intercalated between the layers of a single cation layered material, copper hydroxide nitrate. Microporous scaffold carbon material was obtained by thermal decomposition of the nanohybrid at 500 °C under argon atmosphere followed by acid washing process. Furthermore, the heat-treated product of the nanohybrid at 600 °C was ultrafine mesoporous metallic copper particles. The results of this study confirmed the great potential of CSLH to produce the carbon material with large surface area (580 m(2)/g) and high pore volume copper powder (2.04 cm(3)/g).     

Untersuchung der Phasenbeziehungen in quaternären Systemen Bi2O3/Bi2Ch/Bi2Ch (Ch = S,Se, Te)

Investigations of the Phase Relations in the Quaternary Systems Bi₂O₃/Bi₂Ch /Bi₂Ch (Ch = S, Se, Te) The stability ranges in the pseudobinary systems Bi₂O₂S/Bi₂O₂Se, Bi₂O₂S/Bi₂O₂Te and Bi₂O₂Se/Bi₂O₂Te have been studied by solid state and chemical transport reactions. A complete mixed crystal Bi₂O₂(Te_xSe_1–x), 0 ≤ x ≤ 1 exists between the ternary compounds Bi₂O₂Te and Bi₂O₂Se. The thermal behaviour of the mixed crystal and the coexistence ranges have been determined by x‐ray and thermal analysis.     

Bi2S3 spheres coated with MOF-derived Co9S8 and N-doped carbon composite layer for half/full sodium-ion batteries with superior performance

Bismuth sulfide (Bi2S3) has attracted particular interest as a potential anode material for sodium-ion batteries (SIBs).However,the low electrical conductivity ...     

3D Nano‐structure L‐cysteine/AuNPs/Bi2O3 Modified Glass Carbon Electrode as Chemical Sensor for Highly Sensitive and Selective Detection Cu (II)

It was first time using the l‐cysteine self‐assembled on the surface of gold nanoparticles and Bi₂O₃ nano‐structured materials modified GCE composed l‐cysteine/AuNPs/Bi₂O₃/GCE sensor. The sensor possessed three‐dimensional nanostructure and exhibited a higher ratio of activity sites, large active surface, fast electron transfer rate, excellent catalytic, sensing characteristics and larger affinity to Cu (II). The sensor was determined to have an excellent sensitivity and selectivity for the detection of Cu (II). The characterization of sensor as well as the optimization of the analytical procedure was reported. The optimized conditions parameters allowed the detection of Cu (II) concentration following short analysis time, a detection limit of 5×10^?11 M at 80 s of preconcentration time was obtained using the as‐prepared sensor, and also show excellent stability and good repeatability, and, thus, could be used for detection of Cu (II) in environment.     

Coordination of Bimuth(III) to Cucurbit[8]uril. Preparation and X‐ray Structure of [{Bi(NO3)(H2O)5}2(Q8)][Bi(NO3)3(H2O)4]2[Bi(NO3)5]2·Q8·19H2O

Bi(NO₃)₃ reacts with cucurbit[8]uril, (Q8), in 3M HNO₃ to give the title complex whose structure includes three discrete Bi complexes: [{Bi(NO₃)(H₂O)₅}₂(Q8)]⁴⁺ (CN of Bi = 9, both NO₃^— and cucurbit[8]uril are bidentate), [Bi(NO₃)₅]^2— (CN of Bi = 10, all NO₃^— are bidentate), and [Bi(NO₃)₃(H₂O)₄] (CN of Bi = 10, all NO₃^— are bidentate).     

Synthesis and crystal chemistry of two new fluorite-related bismuth phosphates, Bi(4.25)(PO4)2O(3.375) and Bi5(PO4)2O4.5, in the Series Bi4+x(PO4)2O3+3x/2 (0.175 < or = x < or = 1)

Two new phosphates, Bi(4.25)(PO4)2O(3.375) and Bi(5)(PO(4))(2)O(4.5), have been analyzed by single-crystal X-ray diffraction in the series Bi(4+x)(PO4)2O(3+3x/2) (0.175 < or = x < or = 1). The syntheses of the compositions ranging from x = 0.175 to 0.475 were carried out by the ceramic route. The compositions from x = 0.175 to 0.475 form a solid solution with a structure similar to that of Bi(4.25)(PO4)2O(3.375), while Bi(5)(PO4)2O(4.5) was isolated from a mixture of two phases. Both of the phases form fluorite-related structures but, nevertheless, differ from each other with respect to the arrangement of the bismuth atoms. The uniqueness in the structures is the appearance of isolated PO(4) tetrahedra separated by interleaving [Bi2O2] units. ac impedance studies indicate conductivity on the order of 10(-5) S cm(-1) for Bi(4.25)(PO4)2O(3.375). Crystal data: Bi(4.25)(PO4)2O(3.375), triclinic, space group P (No. 1), with a = 7.047(1) A, b = 9.863(2) A, c = 15.365(4) A, alpha = 77.604(4) degrees, beta = 84.556(4) degrees, gamma = 70.152(4) degrees, V = 980.90(4) A3, and Z = 4; Bi(5)(PO4)2O(4.5), monoclinic, space group C2/c (No. 15), with a = 13.093(1) A, b = 5.707(1) A, c = 15.293(1) A, beta = 98.240(2) degrees, V = 1130.95(4) A(3), and Z = 8.