Separation and determination of toxic pyrrolizidine alkaloids in traditional Chinese herbal medicines by micellar electrokinetic chromatography with organic modifier

A simple and rapid micellar electrokinetic chromatography (MEKC) method was developed for the separation and determination of four toxic pyrrolizidine alkaloids (PAs) (senkirkine, senecionine, retrorsine, and seneciphylline) in two traditional Chinese herbal medicines (Qian liguang and Kuan donghua). Separation was performed in the running buffer consisting of 20 mM borate, 30 mM SDS, and 20% methanol at pH 9.1. With the optimized separation conditions, four PAs were separated in 17 min by a single run. The calibration curves showed good linearity with correlation efficiencies (R(2)) between 0.9940 and 0.9988. RSDs in migration time and peak area were 0.31, 0.40, 0.39, 0.48% and 3.28, 3.48, 4.16, 3.42% for senkirkine, senecionine, retrorsine, and seneciphylline, respectively. Limits of detection (S/N = 3) varied from 1.19 to 2.70 microg/mL. The proposed method was applied to determine the PAs extracted from Chinese herbal medicines (Qian liguang and Kuan donghua). PA of senkirkine in Kuan donghua was detected and the amount was found to be 79.1 microg/g. The results obtained indicate that the proposed MEKC method could potentially become an effective alternative tool for qualification control and quantitative analysis of herbal medicines in pharmaceutical industry.     

胶束扫集毛细管电动色谱法测定药物中3种邻苯二甲酸酯

采用胶束扫集毛细管电动色谱技术,建立了测定药物中邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DZP)和邻苯二甲酸二丁酯(DBP)的方法。电泳缓冲体系含80 mmol/L SDS,20 mmol/L NaH2PO4(pH 2.20),5%甲醇(V/V),分离电压-18 kV,重力进样80s×15.0cm,检测波长225 nm,使用Φ50μm×62.0 cm石英毛细管,有效长度50.0 cm。讨论了磷酸盐浓度、有机改善剂、SDS浓度、分离电压、进样时间等因素的影响,并考察了胶束扫集法对DMP、DEP和DBP的富集能力。在优化条件下,线性关系良好,相关系数大于0.9986,DMP、DEP和DBP的线性范围分别为1.25～240,1.04～200和1.56～200 mg/L,检出限分别为0.26,0.26和0.39 mg/L。方法应用于肠溶片中DMP、DEP和DBP的测定,回收率在93.3%～108%之间,RSD≤5.2%。每次样品测定可在10 min内完成。     

High-sensitivity analyses of metabolites in biological samples by capillary electrophoresis using dynamic pH junction-sweeping

Emerging fields of biochemical research, such as metabolomics, present challenges to current separation technologies because of the large number of metabolites present in a cell and their often low (submicromolar) concentration. Although capillary electrophoresis (CE) holds great promise as the method of choice for high-resolution separations of biological samples, it suffers from poor concentration sensitivity, especially with the use of UV detection. In CE, sweeping and dynamic pH junction represent two complementary on-line focusing techniques that have been used for sensitivity enhancement of hydrophobic and weakly acidic analytes, respectively. However, the application of either the sweeping or dynamic pH junction technique alone might, in some cases, be less effective for the analysis of certain sample mixtures. Recent work in the development of a hyphenated dynamic pH junction-sweeping technique is presented as an effective on-line method of preconcentration suitable for both hydrophilic (anionic) and hydrophobic (neutral) analytes. Sensitive analyses of flavin metabolites by CE with laser-induced fluorescence (LIF) detection is demonstrated in various biological matrixes, including cell extracts of Bacillus subtilis, pooled human plasma, as well as heat-deproteinized flavoenzymes. Enhanced analyte band narrowing and improved sensitivity is achieved for flavins using dynamic pH junction-sweeping compared to either sweeping or dynamic pH junction alone. This results in over a 1200-fold improvement in sensitivity relative to conventional injection methods, giving a limit of detection (LOD, defined as S/N = 3) of about 4.0 x 10(-12) M. Strategies for sensitive and more comprehensive analyses of other cell metabolites, including nucleotides, coenzymes, and steroids, are also discussed when using on-line focusing techniques in conjunction with multiplexed CE and UV detection.     

Sensitive determination of pyrrolizidine alkaloids in Tussilago farfara L. by field‐amplified,sample‐stacking,sweeping micellar electrokinetic chromatography

Pyrrolizidine alkaloids are the toxic components in Tussilago farfara L. Due to the lack of standard substances for quantitative analysis and traces of pyrrolizidine alkaloids in total alkaloids, the full quality control of Tussilago farfara L has been limited. In this study, we aimed to solve the difficulty of determination of pyrrolizidine alkaloids and identify more components in the total alkaloids. An on‐line preconcentration method has been applied to improve determining sensitivity of pyrrolizidine alkaloids in Tussilago farfara L. in which included field‐amplified sample stacking and sweeping in micellar electrokinetic capillary chromatography. The main parameters that affected separation and stacking efficiency were investigated in details. Under the optimal conditions, the sensitivity enhancement factors obtained by the developed method for the analytes were from 15‐ to 12‐fold, the limits of detection of senkirkine and senecionine were 2～5 μg/L. Senkirkine and senecionine have been detected in alkaloids ( c ) of Tussilago farfara L, along ferulic acid methyl ester and methyl caffeate. The developed method was also applied to the analysis of acid extraction ( a ) of Tussilago farfara L, and senkirkine could be detected directly. The results indicated that the developed method is feasible for the analysis of pyrrolizidine alkaloids in Tussilago farfara L with good recoveries.     

On-line sample preconcentration of cationic analytes by dynamic pH junction in capillary electrophoresis

To improve detection sensitivity of cationic analytes, a dynamic pH junction technique was examined. Dynamic pH junction is an on-line focusing method in capillary electrophoresis (CE) based on the difference in the analyte's mobility between the background electrolyte (BGE) and sample matrix. The effects of pH values and concentrations of the BGE and the sample matrix on dynamic pH junction were examined. Optimization of analyte focusing resulted in enhanced detection responses of about 100-160-fold in terms of peak heights for some anilines in comparison to conventional injections. In particular, the concentration limits of detection (LOD) (S/N = 3) for the test anilines obtained with dynamic pH junction were from 1.9 to 3.7 ppb with UV detection without any pretreatment procedure.     

Nonaqueous capillary electrophoresis for the analysis of selected tropane alkaloids in a plant extract

Summary The potential of nonaqueous capillary electrophoresis has been investigated for the separation of structurally similar tropane alkaloids. The effects of the organic solvent and of electrolyte composition on separation selectivity, migration times, and efficiency are described. The addition of trifluoroacetic acid to the separation buffer was found beneficial for manipulation of the order of migration of the two positional isomers littorine and hyoscyamine. Replicate injections under nonaqueous conditions gave migration time and peak area data of excellent precision. The application of the optimized conditions to the analysis of hyoscyamine and scopolamine in genetically transformed root cultures ofDatura candida x D. aurea is presented.     

动态pH联接-扫集毛细管电泳法测定化妆品中迷迭香酸的含量

采用动态pH联接-扫集毛细管电泳法对化妆品中的迷迭香酸进行检测。用重力进样的方式,进样高度为15 cm的情况下,研究了硼砂浓度、pH、十二烷基硫酸钠(SDS)浓度、甲醇浓度、样品基体、进样时间、分离电压对富集与分离的影响。优化后的实验条件:15 mmol/L硼砂-45 mmol/L SDS(pH8.8)-15%甲醇为缓冲液,进样时间60s,分离电压16kV,样品中磷酸盐浓度10 mmol/L,样品基质pH 4.7。在上述条件下,迷迭香酸(RA)的线性回归方程式为y=539200ρ+53588(r=0.9985),线性范围为0.144～3.6μg/mL,检出限0.036μg/mL,迷迭香酸的回收率为92.5%～103%,相对标准偏差为2.5%。     

Enhancing detectability in CE by combining an isotachophoretic preconcentration with capillary zone electrophoresis in a single capillary

Summary This paper describes a strategy where a major part of a single capillary is filled with sample which when is isotachophoretically (ITP) preconcentrated while a hydrodynamic backpressure is applied to keep the analytes in the capillary. In the subsequent analysis of the test compounds, amitriptyline and metoprolol, capillary zone electrophoresis is used. The concentration limit of detection is lowered at least 170 times. Preliminary results where an ITP-preconcentration is combined with micellar electrokinetic chromatography with a neutral micellar agent is also presented.     

Comparison of two capillary electrophoresis online stacking modes by analysis of polycyclic aromatic hydrocarbons in airborne particulates

Naphthalene, fluorene, pyrene, anthracene, phenanthrene, and chrysene were successfully separated by CD-modified MEKC (CD-MEKC) using 20 mM borate (pH 9.0) containing 90 mM SDS and 75 mM beta-CD. Two online stacking methods, i.e., sweeping and field-enhanced sample injection (FESI), were explored to enhance the detection sensitivity. The influences of some crucial parameters in sweeping and FESI procedures were investigated. For FESI method, a plug of water and low-conductivity sample matrix was used to increase the stacking efficiency. Compared with the sweeping method, FESI can increase the sensitivity in the range of 10-20-fold. The proposed method was used for the analysis of polycyclic aromatic hydrocarbons in airborne particulates.     

Online preconcentration of arsenic compounds by dynamic pH junction-capillary electrophoresis

An online preconcentration technique by dynamic pH junction was studied to improve the detection limit for anionic arsenic compounds by CE. The main target compound is roxarsone, or 3-nitro-4-hydroxyphenylarsonic acid, which is being used as an animal feed additive. The other inorganic and organoarsenic compounds studied are the possible biotransformation products of roxarsone. The arsenic species were separated by a dynamic pH junction in a fused-silica capillary using 15 mM phosphate buffer (pH 10.6) as the BGE and 15 mM acetic acid as the sample matrix. CE with UV detection was monitored at a wavelength of 192 nm. The influence of buffer pH and concentration on dynamic pH junction were investigated. The arsenic species focusing resulted in LOD improvement by a factor of 100-800. The combined use of C18 and anion exchange SPE and dynamic pH junction to CE analysis of chicken litter and soils helps to increase the detection sensitivity. Recoveries of spiked samples ranged between 70 and 72%.     

反向微乳毛细管电泳法在线富集技术灵敏检测化妆品中的多环芳烃

要建立了反向微乳毛细管电泳(MEEKC)在线富集技术灵敏检测多环芳烃的方法。采用大体积进样-p H动态连接-扫集微乳毛细管电泳法(LVSS-Dyp H-MEEKC)对于常规条件下很难分离的6种强亲脂性的多环芳烃中性分子进行富集分离。结果表明,在反相电压下,当微乳液的组成为:2.4%(w/w)SDS、0.6%(w/w)正辛烷、6.6%(w/w)正丁醇、20 mmol/L Na H2PO4缓冲液(p H 2.2);进HCB时间为20 s(16 k Pa),进样时间为80 s(16 k Pa)时,富集效果良好,富集倍数在25~80倍之间,在27 min内实现了对多环芳烃化合物的灵敏检测。将本方法用于化妆品中多环芳烃的检测,回收率在90.6%~95.9%之间,相对标准偏差均小于5.1%(n=5)。     

Stacking and separation of urinary porphyrins in capillary electrophoresis: optimization of concentration efficiency and resolution

We demonstrated that anionic porphyrins could be stacked and separated in micellar electrokinetic chromatography (MEKC) and microemulsion electrokinetic chromatography (MEEKC) by applying acetonitrile and high salt content in human urine sample matrix. The introduction of sample containing acetonitrile and sodium chloride into the CE capillary at more than 10% of the total capillary volume resulted in the improvement of peak resolution and the enhancement of detection sensitivity. The achieved acetonitrile stacking enrichment factors of six porphyrins ranged from 12 to 32 in MEKC and from 28 to 33 in MEEKC, respectively. The stacking technique was successfully applied for analyzing porphyrins present in urine samples that were deproteinized with acetonitrile. For the analysis of coproporphyrin isomers, addition of the sodium cholate (SC) into micelle and microemulsion solutions provided adequate resolution. Calibration curves obtained for the determination of coproporphyrin isomers were found linear between 30 and 400 nmol L⁻¹, and the limit of detection (LOD) was 20 nmol L⁻¹ in MEEKC. Intra- and interday precisions (n = 11) in the microemulsion separation system for the isomers at spiked concentrations of 40-400 nmol L⁻¹ in urine were in the range of 0.1-0.4% and 0.7-7.6% for migration time and peak area, respectively. Coproporphyrin III, coproporphyrin I and uroporphyrin were detected at levels of 80.7 nmol L⁻¹, 32.3 nmol L⁻¹ and 19.8 nmol L⁻¹, respectively, in the urine samples collected from healthy individuals. Different porphyrin profiles, however, were observed in urine samples from porphyria cutanea tarda (PCT) patients.     

Micellar electrokinetic capillary chromatography for selected tropane alkaloid analysis in plant extract

Summary Micellar electrokinetic capillary chromatography was applied to the simultaneous analysis of six tropane alkaloids, including hyoscyamine and scopolamine. Successful results were obtained using a 30 mM boratephosphate buffer at basic pH (8.5) in the presence of 50 mM sodium dodecyl sulfate. The operating conditions, such as buffer concentration and pH, micelle concentration and organic modifier type and percentage were also discussed on the basis of the results given with a tropane alkaloid mixture. Addition of organic modifiers showed an improvement in separation efficiency and resolution. Moreover, hyoscyamine and littorine, two positional isomers, were only resolved by the addition of organic solvents such as methanol or acetonitrile. The optimized conditions were finally applied to the analysis of tropane alkaloids found in genetically transformed root cultures ofDatura candida x D. aurea. Dedicated to Professor Werner Haerdi on the occasion of his 70^th birthday.     

Low-temperature bath/coupled-capillary/sweeping-micellar electrokinetic capillary chromatography for the separation of naphthalene-2,3-dicarboxaldehyde-derivatized dopamine and norepinephrine

The use of a low-temperature (0 degrees C) bath-assisted coupled capillary for the separation of naphthalene-2,3-dicarboxaldehyde (NDA)-derivatized dopamine and norepinephrine using the sweeping-micellar electrokinetic capillary chromatography (MEKC) mode is described. In this technique, a capillary consisting of two portions with different inside diameters is used. Therefore, the field strength inside the capillary is different. Hence, the electrophoretic migration velocities of the analytes and the electro-osmotic flow (EOF) also are different. Furthermore, when a portion of the capillary (wide portion, used for sweeping) is immersed in a low-temperature bath, the viscosity of the buffer and the retention factor of the analytes inside are increased. Thus, not only are the interactions between the SDS micelles and the analytes increased, but the SDS-analytes also move more slowly. As a result, a more complete separation can be achieved, even when the sample injection volume is large, up to approximately 2 microL. In general, when the volume of an injected sample is larger, the effects of sweeping and separation would become insufficient, especially when the retention values (k) of the analytes are quite different. However, this limitation can be improved when the low-temperature bath/coupled capillary/sweeping-MEKC mode is used.     

Dispersive liquid–liquid microextraction combined with online preconcentration MEKC for the determination of some phenoxyacetic acids in drinking water

A fast and simple technique composed of dispersive liquid–liquid microextraction (DLLME) and online preconcentration MEKC with diode array detection was developed for the determination of four phenoxyacetic acids, 2,4,5‐trichlorophenoxyacetic acid, 2,4‐dichlorophenoxyacetic acid, 2,6‐dichlorophenoxyacetic acid, and 4‐chlorophenoxyacetic acid, in drinking water. The four phenoxyacetic acids were separated in reversed‐migration MEKC to the baseline. About 145‐fold increases in detection sensitivity were observed with online concentration strategy, compared with standard hydrodynamic injection (5 s at 25 mbar pressure). LODs ranged from 0.002 to 0.005 mg/L using only the online preconcentration procedures without any offline concentration of the extract. A DLLME procedure was used in combination with the proposed online preconcentration strategies, which achieved the determination of analytes at limits of quantification ranging from 0.2 to 0.5 μg/kg, which is far lower than the maximum residue limits established by China. The satisfactory recoveries obtained by DLMME spiked at two levels ranged from 67.2 to 99.4% with RSD <15%, making this proposed method suitable for the determination of phenoxyacetic acids in water samples.     

Analysis of protoberberine alkaloids in several herbal drugs and related medicinal preparations by non-aqueous capillary electrophoresis

A simple, rapid, reproducible, and universal non-aqueous capillary electrophoresis method has been developed for the separation and determination of three major active protoberberine alkaloids including berberine, palmatine, and jatrorrhizine within 7 min. The effects of the concentrations of acetic acid and electrolyte, the ratio of organic solvent, and the applied voltage on the separation were investigated. The optimum running buffer was composed of 50 mM ammonium acetate, 0.5% (v/v) acetic acid, and 10% (v/v) acetonitrile in methanol. The applied voltage was 18 kV. The analytes were detected by UV at 214 nm. The linearities between peak areas and the concentrations of the analytes were also investigated, and they exhibit excellent linear behavior over the concentration ranges (correlation coefficients: 0.9975-0.9986). The method was successfully applied to determine the three alkaloids in several families of herbal drugs (Rhizoma Coptidis, Cortex Berberidis, Cortex Phellodendri, Herba Chelidonii, Caulis Mahoniae) and their relevant medicinal preparations for the first time, and the recoveries of the three constituents ranged between 95.6-103.2% for berberine, 97.5-103.3% for palmatine, and 96.1 -103.6% for jatrorrhizine.     

Different strategies for the preconcentration and separation of parabens by capillary electrophoresis

Several strategies, namely, large volume sample stacking (LVSS), field‐amplified sample injection (FASI), sweeping, and in‐line SPE‐CE, were investigated for the simultaneous separation and preconcentration of a group of parabens. A BGE consisting of 20 mM sodium dihydrogenphosphate (pH 2.28) and 150 mM SDS with 15% ACN was used for the separation and preconcentration of the compounds by sweeping, and a BGE consisting of 30 mM sodium borate (pH 9.5) was used for the separation and preconcentration of the compounds by LVSS, FASI, and in‐line SPE‐CE. Several factors affecting the preconcentration process were investigated in order to obtain the maximum enhancement of sensitivity. The LODs obtained for parabens were in the range of 18–27, 3–4, 2, and 0.01–0.02 ng/mL, and the sensitivity evaluated in terms of LODs was improved up to 29‐, 77‐, 120‐, and 18 400‐fold for sweeping, LVSS, FASI, and in‐line SPE‐CE, respectively. These preconcentration techniques showed potential as good strategies for focusing parabens. The four methods were validated with standard samples to show the potential of these techniques for future applications in real samples, such as biological and environmental samples.     

Comparative study of capillary zone electrophoresis and micellar electrokinetic chromatography for the separation of twelve aromatic sulphonate compounds

Summary Two modes of capillary electrophoresis (CE), capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC), were investigated for the separation of 12 aromatic sulphonate compounds. In CZE, although the voltage applied, the buffer concentration and the pH were optimized for effective separation of the compounds studied, under the best conditions four of the five amino compounds coeluted, as did naphthalene-1-sulphonic acid and naphthalene-2-sulphonic acid. In MEKC, sodium dodecyl sulphate (SDS) and Brij 35 were chosen as the anionic and nonionic surfactants and the effect of the concentration of micelles was examined. The effect of adding methanol as the organic modifier was also investigated with each of these micellar systems. All the analytes, including the isomers, were completely separated by use of MEKC with Brij 35 but when SDS was used only 11 compounds were separated because two amino compounds coeluted.     

Quantification of the bisphosphonate alendronate using capillary electrophoresis mass spectrometry with dynamic pH barrage junction focusing

A quantitative method was developed for the direct identity confirmation and quantification of alendronate using CE-MS combined with a pH-assisted focusing technique, dynamic pH barrage junction focusing. A pH-induced variation in electrophoretic mobility led to online focusing of alendronate at the sample/pH barrage boundary, significantly improving the detection sensitivity. In addition, the use of a flow-through microvial CE electrospray interface and the multiple reaction monitoring mode of MS further improved the specificity and quantification capability of this technology. This quantitative method presented a wide linear dynamic range over 8–2000 ng/mL and an LOD of 2 ng/mL. A 460-fold improvement in sensitivity was obtained when pH barrage junction focusing was applied during the CE process, in comparison to when normal CE was conducted without online sample stacking. The superior detection sensitivity over previously reported methods enables direct analysis of bisphosphonate compounds, eliminating tedious pre-column sample enrichment and derivatization. Validation of alendronate content in a commercial drug tablet further proved the reliability and power of this method. This simple method with no sample derivatization, superior sensitivity, and short run time (<8 min) is a promising alternative for accurate quantification of alendronate and other types of bisphosphonate compounds in both drug formulations and plasma samples.     

Online preconcentration of recombinant Arg-Gly-Asp-hirudin using dynamic pH junction for analysis in human urine samples by capillary electrophoresis-mass spectrometry

A sensitive and effort-saving method was established and validated for the quantitative determination of recombinant Arg-Gly-Asp-hirudin (rRGD-hirudin) in human urine samples. The assay was performed on a uncoated fused silica capillary of 70 cm × 50 μm I.D. and a positive voltage of 30 kV was applied. The sample was injected under pressure of 50 mbar for 300 s and the temperature of capillary was kept 25 °C. Sheath liquid consisting of 30% methanol and 70% of 0.1% formic acid aqueous solution flowing at 7 μL/min was supplied to the CE-electrospray interface. Utilizing the dynamic pH junction technique, a lower limit of quantitation of approximately 35 nM was achieved (concentration coefficiency was about 100-fold) without complex sample preprocessing procedure. CE-MS conditions and parameters were also optimized to obtain better performance. The method has been successfully applied in clinical research of rRGD-hirudin.