Smart computing approach for design and scale-up of conical spouted beds with open-sided draft tubes

Open-sided draft tubes provide an optimal gas distribution through a cross flow pattern between the spout and the annulus in conical spouted beds.The design,optimization,control,and scale-up of the spouted beds require precise information on operating and peak pressure drops.In this study,a multi-layer perceptron(MLP)neural network was employed for accurate prediction of these hydrodynamic characteristics.A relatively huge number of experiments were accomplished and the most influential dimensionless groups were extracted using the Buckingham-pi theorem.Then,the dimensionless groups were used for developing the MLP model for simultaneous estimation of operating and peak pressure drops.The iterative constructive technique confirmed that 4-14-2 is the best structure for the MLP model in terms of absolute average relative deviation(AARD%),mean square error(MSE),and regression coefficient(R²).The developed MLP approach has an excellent capacity to predict the transformed operating(MSE=0.00039,AARD%=1.30,and R²=0.76099)and peak(MSE=0.22933,AARD%=11.88,and R2=0.89867)pressure drops.     

Effective enhanced model for a large deformable soft pneumatic actuator

Soft pneumatic actuators have been widely used for implementing sophisticated and dexterous movements,due to numerous fascinating features compared with their rigid counterparts.Relatively speaking,modeling and analysis of an entire soft pneumatic actuator considering contact interaction between two adjacent air chambers is extremely rare,which is exactly what we are particularly interested in.Therefore,in order to establish an accurate mechanical model and analyze the overall configuration and stress distribution for the soft pneumatic actuator with large deflection,we consider the contact interaction of soft materials rather than hard materials,to produce an effective enhanced model for soft contact of a large deformable pneumatic actuator.In this article,a multiple-point contact approach is developed to circumvent the mutual penetration problem between adjacent air chambers of the soft actuator that occurs with the single-point contact approach employed in linear elastic rigid materials.In contrast to the previous simplified rod-based model that did not focus on contact interaction which was adopted to clarify the entire deformation of the actuator,the present model not only elaborates nonlinear large deformation and overall configuration variations,but also accurately delineates stress distribution law inside the chamber structure and the stress concentration phenomenon.By means of a corresponding static experiment,a comparison of the simulation results with experimental data validates the effectiveness and accuracy of this model employing a multiple-point contact approach.Excellent simulation of the actual bending deformation of the soft actuator is obtained,while mutual penetration is successfully circumvented,whereas the model with single-point contact cannot achieve those goals.Finally,as compared with the rod-based model,the results obtained using the proposed model are more consistent with experimental data,and simulation precision is improved.     

Axially variable-length solid element of absolute nodal coordinate formulation

An axially variable-length solid element with eight nodes is proposed by integrating the arbitrary Lagrangian-Eulerian (ALE) formulation and the absolute nodal coordinate formulation (ANCF). In addition to the nodal positions and slopes of eight nodes, two material coordinates in the axial direction are used as the generalized coordinates. As a consequence, the nodes in the ALE-ANCF are not associated with any specific material points and the axial length of the solid element can be varied over time. These two material coordinates give rise to a variable mass matrix and an additional inertial force vector. Computationally efficient formulae of the additional inertial forces and elastic forces, as well as their Jacobians, are also derived. The dynamic equation of a flexible multibody system (FMBS) with variable-length bodies is presented. The maximum and minimum lengths of the boundary elements of an FMBS have to be appropriately defined to ensure accuracy and non-singularity when solving the dynamic equation. Three numerical examples of static and dynamic problems are given to validate the variable-length solid elements of ALE-ANCF and show their capability.     

Application of micro-morphology in the physical characterization of urban road dust

Urban road dust was collected from Vellore City,Tamil Nadu,India,and analyzed.Scanning electron microscopy(SEM)was used to examine road dust from nine sampling locations in the study region.SEM image analysis was used to identify various shape factors of collected dust particles.The equivalent spherical diameter of most particles was between 10μm and 30μm.Fine particles had greater concentrations at locations with higher traffic flow.Particles were categorized into four classes based on their shape factors,viz.,spherical,mineral,elongated,or irregular.Spherical particles had the smallest mean equivalent diameter(1.95μm)and mineral particles had the largest diameter(33.3μm).Spherical particles made up the smallest portion of road dust(0-12%)in the study region and mineral particles made up the largest(45-65%).Elongated and irregular particles,each made up 23-30%of road dust.Electron dispersive X-ray spectroscopy analysis was used to identify the elemental composition of dust particles.Spherical particles were mostly from combustion sources and mineral particles were largely of crustal origin.No individual source was found for irregular and elongated particles.Biological debris was the major source of irregular particles.     

Efficient algorithm for 3D bimodulus structures

The bimodulus material is a classical model to describe the elastic behavior of materials with tension-compression asymmetry.Due to the inherently nonlinear properties of bimodular materials,traditional iteration methods suffer from low convergence efficiency and poor adaptability for large-scale structures in engineering.In this paper,a novel 3D algorithm is established by complementing the three shear moduli of the constitutive equation in principal stress coordinates.In contrast to the existing 3D shear modulus constructed based on experience,in this paper the shear modulus is derived theoretically through a limit process.Then,a theoretically self-consistent complemented algorithm is established and implemented in ABAQUS via UMAT;its good stability and convergence efficiency are verified by using benchmark examples.Numerical analysis shows that the calculation error for bimodulus structures using the traditional linear elastic theory is large,which is not in line with reality.     

Instability inspection of parametric vibrating rectangular Mindlin plates lying on Winkler foundations under periodic loading of moving masses

Parametric resonance is one of the most important issues in the study of dynamical behavior of structures. In this paper, dynamic instability of a moderately thick rectangular plate on an elastic foundation is investigated in the case of parametric and external resonances due to periodic passage of moving masses. The governing coupled partial differential equations (PDEs) of the system, with consideration of the first-order shear deformation theory (FSDT) or Mindlin plate theory, are presented and they are reduced to a set of ordinary differential equations (ODEs) with time-dependent coefficients using the Galerkin procedure. All inertial components of the moving masses are adopted in the dynamical formulation. Instability survey is carried out for three different loading trajectories considerably interested in many practical applications of the issue, i.e. rectilinear, diagonal and orbiting trajectories. In order to analyze the resonance conditions, the incremental harmonic balance (IHB) method is introduced to calculate instability boundaries, as well as external resonance curves in parameters plane. A comprehensive study is done to assess effects of thickness ratio and foundation stiffness on the resonance conditions. It is found that an increase in the plate's thickness ratio leads to a reduction in values of critical parameters. Moreover, it is observed that in creasing the foundation stiffness moves the in stability regions and resona nee curves to higher frequencies of the moving masses and also leads to further stability of the parametrically excited system at lower frequencies. Time response simulations done via Runge-Kutta method confirmed the results predicted by IHB method.     

Towards multi-fidelity simulation of flows around an underwater vehicle with appendages and propeller

Flow around a real-life underwater vehicle often happens at a high Reynolds number with flow structures at different scales from the boundary layer around a blade to that around the hull. This poses a great challenge for large-eddy simulation of an underwater vehicle aiming at resolving all relevant flow scales. In this work, we propose to model the hull with appendages using the immersed boundary method, and model the propeller using the actuator disk model without resolving the geometry of the blade. The proposed method is then applied to simulate the flow around Defense Advanced Research Projects Agency(DARPA) suboff. An overall acceptable agreement is obtained for the pressure and friction coefficients. Complex flow features are observed in the near wake of suboff. In the far wake, the core region is featured by a jet because of the actuator disk, surrounded by an annular region with velocity deficit due to the body of suboff.     

Theoretical analysis on elastic buckling of nanobeams based on stress-driven nonlocal integral model

Several studies indicate that Eringen’s nonlocal model may lead to some inconsistencies for both Euler-Bernoulli and Timoshenko beams, such as cantilever beams subjected to an end point force and fixed-fixed beams subjected a uniform distributed load. In this paper, the elastic buckling behavior of nanobeams, including both EulerBernoulli and Timoshenko beams, is investigated on the basis of a stress-driven nonlocal integral model. The constitutive equations are the Fredholm-type integral equati...     

Shear behaviours of cohesionless mixed soils using the DEM:The influence of coarse particle shape

The coarse particles in mixed soils can be cobbles or gravels,with the main difference being their roundness(an indicator describing particle shape characteristics at an intermediate scale).The influence of coarse particle shape(i.e.,roundness)on the macroscopic and microscopic shear behaviours of cohesionless mixed soils with various fines contents(FCs)was investigated via the discrete element method in this study.The shapes of coarse particles were formed using the rotation-invariant spherical harmonic method proposed by previous investigators.An equation was proposed to predict the initial void ratios of samples in this study.A decrease in the roundness of coarse particles can increase the peak friction angle(FC≤40%)and critical friction angle(FC≤30%).As the roundness of coarse particles decreases,the peak dilatancy angle initially increases and then decreases(FC≤20%).Furthermore,it was found that the roundness of coarse particles hardly affects the classification of cohesionless mixed soils,as determined by probing the percentage contributions of coarse-coarse,coarse-fine,and fine-fine contacts.When cohesionless mixed soils change from an underfilled structure to an interactive-underfilled structure at the critical state,the main forms of coarse-coarse contacts were discovered.Additionally,the force-fabric anisotropy mechanisms of the influences of the roundness and rolling resistance coefficient of coarse particles on the shear strengths of cohesionless mixed soils were found to be different.     

Reaction performance of fluidized bed catalytic reactor of Group C+particles

Group C particles are often regarded as non-fluidizable but have proven to effectively fluidize with nanoparticle addition,which results in small bubbles and a high gas holdup in the dense phase during the experiments.Group C⁺particles provide an increased surface area for gas-solid contact and improve the reaction performance,especially for gas-phase catalytic reactions.On the basis of a previous study of the ozone decomposition reaction using Group C⁺particles,a two-phase model was used to evaluate the reactor contact efficiency,and was used to compare the partial oxidation performance of the n-butane to maleic anhydride reaction in fluidized-bed catalytic reactors of Group C⁺and Group A particles.The reactor with Group C⁺particles achieved a higher n-butane conversion and MAN yield compared with that using Group A particles,based on the identical catalyst quantity or on the same gas residence time.Therefore,the reactor with Group C⁺particles can achieve the same reaction conversion and yield with fewer catalysts or a smaller reactor size,or both.Therefore,the fluidized bed catalytic reactor of Group C⁺particles is expected to be of major significance in industrial processes,especially for gas-phase catalytic reactions.     

Preface

This special issue of PARTICUOLOGY is devoted to the first UK-China Particle Technology Forum taking place in Leeds, UK, on 1-3 April 2007. The forum was initiated by a number of UK and Chinese leading academics and organised by the University of Leeds in collaboration with Chinese Society of Particuology, Particle Technology Subject Group （PTSG） of the Institution of Chemical Engineers （IChemE）, Particle Characterisation Interest Group （PCIG） of the Royal Society of Chemistry （RSC） and International Fine Particle Research Institute （IFPRI）. The forum was supported financially by the Engineering and Physics Sciences Research Council （EPSRC） of United Kingdom,     

The 7th International Conference on Fluid Mechanics May 24-27,2015,Qingdao,China

正http://www.icfm7.org First Announcement and Call for PapersThe objective of International Conference on Fluid Mechanics(ICFM)is to provide a forum for researchers to exchange new ideas and recent advances in the fields of theoretical,experimental,computational Fluid Mechanics as well as interdisciplinary subjects.It was successfully convened by the Chinese Society of Theoretical and Applied Mechanics(CSTAM)in Beijing(1987,     

INFORMATION FOR CONTRIBUTORS

Contributions： The Journal, Acta Mechanica Solida Sinica, is pleased to receive papers from engineers and scientists working in various aspects of solid mechanics. All contributions are subject to critical review prior to acceptance and publication.     

Guide for authors

正Each of the sections below provides essential information for authors.We recommend that you take the time to read them before submitting a contribution to Acta Mechanica Sinica.We hope our guide to authors may help you navigate to the appropriate section.How to prepare a submission This document provides an outline of the editorial process involved in publishing a scientific paper in Acta Mechanica Sinica.     

基于鲁棒滤波的捷联导引头视线角速度估计方法

针对捷联导引头无法直接获取视线角速度等信息的问题,研究了鲁棒滤波在大气层外飞行器捷联导引头视线角速度估计中的应用。为了建立非线性滤波估计模型,考虑目标视线角速度的慢变特性,采用一阶马尔科夫模型建立了状态方程;推导了视线角速度的解耦模型,并建立了量测方程;考虑到实际应用中存在系统噪声统计特性失准的问题,基于Huber-Based鲁棒滤波方法,设计了视线角速度滤波器,并完成了基于Huber-Based滤波方法和扩展卡尔曼滤波方法的数学仿真。仿真结果表明Huber-Based滤波方法的视线角、视线角速度及视线角加速度估计精度分别达到0.1140'、0.1423'/s、0.0203'/s2,而扩展卡尔曼滤波方法的视线角、视线角速度及视线角加速度估计精度仅分别为0.6577'、0.6415'/s、0.0979'/s~2。仿真结果证明了该方法可以有效地估计出相对视线角速度等信息,并且在非高斯噪声的条件下,依然可获得较高的估计精度,具有一定的鲁棒性。     

Guide for authors

正Each of the sections below provides essential information for authors.We recommend that you take the time to read them before submitting a contribution to Acta Mechanica Sinica.We hope our guide to authors may help you navigate to the appropriate section.How to prepare a submission This document provides an outline of the editorial process involved in publishing a scientific paper in Acta Mechanica