Tuning hydrophobicity of a fluorinated terpolymer in differently assembled thin films

In the current report, casting from good solvent (acetone) and casting from mixed solvent and nonsolvent were employed for preparing thin films of terpolymer of T etrafluoroethylene (TFE), H exafluoropropylene (HFP), and V inylidene fluoride (VDF) (THV), on silicon wafers. These films revealed various morphologies and wetting behaviors depending on the solution concentration, temperature, and thin film preparation method. The THV thin films prepared by casting from good solvent showed smooth morphology with holes. The thin film prepared from a 3 wt % THV/acetone solution by casting from good solvent at 15 °C demonstrated spheres in addition to the smooth morphology, while the thin film prepared from a 5 wt % THV/acetone solution at 15 °C by casting from good solvent had a mesh‐like structure with some linked spheres. Casting the thin films from mixed solvent and nonsolvent resulted in various morphologies such as different sphere sizes embedded in a dense film layer, and hexagonal close packed structures. The thin films prepared by casting from good solvent showed a slightly hydrophobic character, with a measured water contact angle of approximately 99°, while the nonsolvent cast films had a water contact angle as high as 145°. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 643–657     

用含氟丙烯酸酯无规共聚物制备超疏水膜

用微乳液聚合法制备了丙烯酸全氟烷基乙酯和甲基丙烯酸甲酯的无规共聚物,并对其进行了表征.采用溶剂挥发成膜法一步制备了具有超疏水性的该聚合物膜,水滴在该聚合物膜上的静态接触角可达151°~160°,滚动角小于3°.通过扫描电子显微镜观察发现该聚合物膜表面分布了许多乳突状突起和微孔洞,并具有微米和纳米尺度相结合的复合杂化结构.该类超疏水表面的形成是由适度粗糙的表面和低表面能相互结合引起的.探讨了该类超疏水膜的形成机理.     

The effect of casting solvent on the material properties of poly(γ-methyl-D-glutamate)

The effect of casting solvent on the material properties of poly(γ-methyl-D -glutamate), PMDG, was investigated. The specific solvents used were chloroform, trifluoroacetic acid, dichloroacetic acid, methylene chloride, hexafluoroisopropanol, and tetrachloroethane. The different nature of these solvents controlled the degree of α, β, or random coil contents of the final film. The effect of the morphology on material properties induced by the respective solvents was investigated by dynamic mechanical measurements of the dry films, stress strain behavior of both wet and dry films as well as by wide-angle x-ray diffraction, small-angle light scattering, and optical microscopy. Infrared spectroscopy was used to help determine α or β content. It was found that the casting solvent has considerable influence on material behavior and morphology. These differences are reflected in both the dynamical mechanical (small strain) and stress–strain (large strain) measurements as well as the x-ray scattering and optical microscopy. It was noted by light scattering that all films gave rise to anisotropic rod scattering with the exception of the β film cast from trifluoroacetic acid. This latter film appeared to be optically isotropic.     

Porous structures of polymer films prepared by spin coating with mixed solvents under humid condition

We investigate the effects of interfacial energy between water and solvent as well as polymer concentration on the formation of porous structures of polymer films prepared by spin coating of cellulose acetate butyrate (CAB) in mixed solvent of tetrahydrofuran (THF) and chloroform under humid condition. The interfacial energy between water and the solvent was gradually changed by the addition of chloroform to the solvent. At a high polymer concentration (0.15 g/cm3 in THF), porous structures were limited only at the top surfaces of CAB films, regardless of interfacial energies, due to the high viscosity of the solution. At a medium concentration (approximately 0.08 g/cm3 in THF), CAB film had relatively uniform pores at the top surface and very small pores inside the film because of the mixing of the water droplets with THF solution. When chloroform was added to THF, pores at the inner CAB film had a comparable size with those at the top surface because of the reduced degree of the mixing between the water droplets and the mixed solvent. A further decrease in polymer concentration (0.05 g/cm3 in THF) caused the final films to have a two-layer porous structure, and the size of pores at each layer was almost the same.     

Effect of chloroform on the structure and gas-separation properties of poly(ether imides)

The FTIR spectra of poly(ether imide) films prepared from their chloroform solutions were recorded in a wide temperature interval. The cast films were shown to contain residual solvent. This residual solvent existed in films as unbound chloroform that may be removed by heating to 60–70°C and as bound chloroform that is involved in complex formation with polymers and may be removed by heating at temperatures close to their glass transition temperatures (180°C). Quantum-chemical calculations were performed for structures that model fragments and monomer units of poly(ether imides), as well as their complexes with chloroform. Chloroform was shown to be capable of preferential binding with an oxygen atom in a Ph-O-Ph′ fragment via hydrogen bonds. In this case, the conformational set of poly(ether imide) chains is changed. The above evidence is invoked to explain changes in transport characteristics with time for poly(ether imide) films cast from chloroform solutions.     

An investigation on the influence of a vinyl pyrrolidone/vinyl acetate copolymer on the moisture permeation, mechanical and adhesive properties of aqueous-based hydroxypropyl methylcellulose film coatings

Polymers for aqueous film coating, such as hydroxypropyl methylcellulose (HPMC), often require the inclusion of a plasticizer to reduce brittleness and increase flexibility and ductility. A vinyl pyrrolidone/vinyl acetate copolymer (S630) was investigated for its influence on HPMC film coating parameters, comparing the results with a commonly used plasticizer, polyethylene glycol and another copolymer, polyvinyl alcohol. The viscous properties of the solutions and the glass transition temperatures of the equivalent polymer films were evaluated. Its effect on the film properties, such as appearance, surface roughness, moisture permeation and mechanical properties, as well as its ability to promote better adhesion of the film coat to the core surface, was compared. S630 was able to reduce the viscosity of the polymer solution and glass transition temperature of HPMC, as well as, enhance the mechanical properties of the cast film. The moisture permeation was slightly reduced but not to the same extent as polyethylene glycol. A 10% concentration of S630 increased the adhesive strength and toughness of the HPMC film coat. In conclusion, S630 was effective as a film-former, substrate adhesive and plasticizer. It has the potential to be used to replace the more volatile plasticizers which have problems of loss or migration.     

Poly(caprolactone triol) as plasticizer agent for cellulose acetate films: influence of the preparation procedure and plasticizer content on the physico‐chemical properties

The influence of the plasticizer content and film preparation procedure on the morphology, density, thermal and mechanical properties of cellulose acetate (CA) films plasticized with poly‐(caprolactone triol) (PCL‐T), were studied. Differential scanning calorimetry (DSC), thermal mechanical analysis (TMA), scanning electron microscopy (SEM), wide‐angle X‐ray diffraction (WAXD) and infrared spectroscopy (FT‐IR) techniques were used. The films were prepared by dry‐casting CA and CA/PCL‐T in acetone or acetone/water solutions, which produced transparent and opaque films, respectively. In contrast to the transparent films, which were dense, the opaque films presented a porous morphology. However, the presence of PCL‐T reduced the opaque film porosity, increasing, in consequence, its bulk density. The TMA results revealed that PCL‐T reduced the glass transition temperature more significantly in the transparent than in opaque films. Only the transparent CA/PCL‐T films presented a melting temperature, that reduced with higher concentrations of PCL‐T, suggesting a higher ordering (crystallinity) when the films were prepared in the absence of water, as observed from WAXD curves. The mechanical properties also showed that the transparent films were more soft and tough than the opaque films. In summary, PCL‐T was a good plasticizer agent for CA films due to the presence of hydrogen bonds between the components (FT‐IR spectra). The presence of water in the dry casting process has a significant effect mainly on film morphology and mechanical properties. Copyright © 2004 John Wiley & Sons, Ltd.     

Physico-chemical analysis of semi-crystalline PEEK in aliphatic and aromatic solvents

Polyether ether ketone (PEEK) is a semi-crystalline thermoplastic polymer having excellent mechanical and thermal properties. Exposure of this polymer to aliphatic and aromatic solvents can lead to degradation or swelling of the polymeric material. The present work described the plasticization and stability analysis of semi-crystalline PEEK under different aromatic and aliphatic solvent environment. A variety of solvents (acetone, benzene, benzyl alcohol, chloroform, methanol, and toluene), based on their Hildebrand’s Solubility Parameter, were chosen for investigation. The physico-chemical characteristics of virgin and treated polymeric samples were investigated using Gas Chromatography–Mass Spectrometry (GC–MS), Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and Fourier Transform Infrared Spectroscopy (FTIR) techniques. The results indicated that the solvent exposure did not significantly affect the thermal behavior and chemical structure of the polymer. However, it seems that certain components of the polymer were leached into the solvent phase as revealed by the GC–MS analysis. The present study identified PEEK as a potentially suitable polymer for the applications where high resistance to aliphatic and aromatic solvents is needed.     

Preparation of 4,4-diaryl-2-(tricyanoethenyl)dithienosiloles and vapor-chromic behavior of the film

[reaction: see text] Reactions of 4,4-diphenyl- and 4,4-di(p-tolyl)dithienosilole with tetracyanoethene (TCNE) in DMF gave coupling products 4,4-diphenyl- and 4,4-di(p-tolyl)-2-(tricycanoethenyl)dithienosilole (1a and 1b) in good yield. The films of 1b exhibited vapor-chromism, and the color of the film changed from red to blue-purple upon exposure to the vapor of organic solvents such as ethanol, methanol, acetonitrile, ethyl acetate, acetone, and hexane. The color reverted to the original red upon contact with chloroform vapor, indicating that this process is reversible.     

Role of solvent in the compatibility of a vinylchloride–vinylacetate–maleic acid terpolymer and nitrocellulose blends

The compatibility of cast films of a vinylchloride–vinylacetate–maleic acid terpolymer (VMCH) and nitrocellulose (NC) blends is influenced by solvents. Transparent films of VMCH/NC blends are obtained when cast from solvents such as tetrahydrofuran or cyclohexanone, whereas hazy films are obtained when cast from solvents such as acetone or ethylacetate. Visible spectroscopy and phase morphology were used to analyse the compatibility–incompatibility of the blend. Differential scanning calorimetry (DSC) studies demonstrate that the transparent film is compatible, but the hazy film is incompatible. Fourier transform infra-red (FTIR) studies establish that a greater interaction is observed between the polymer pair in case of the compatible blend than in the case of the incompatible blend. A solvent dependency of blend compatibility is reflected in this study. The conformational state of the polymers in solution, which is responsible for the compatibility phenomena, may depend on the donor number and/or Taft-β value of the solvent. The greater the donor number and/or the Taft-β value, the higher may be the level of interaction between the solvent and the polymer molecules, which in turn may give a compatible blend after removal of the solvent.     

Analysis of Dns-amino acids by liquid chromatography. I. Selection of optimum mobile phase composition for separation of Dns-amino acids on polyvinyl acetate gel.

The separation of a mixture of ten Dns-amino acids (Gns-Gly, -Ala, -Val, -Leu, -Pro, -Hypro, -Met, -Ser, -Asn and -Gln) was carried out by liquid chromatography by using macroreticular polyvinyl acetate gel as a packing material. Different mobile phase systems were investigated, based mainly on mixtures of n-hexane with ethanol, methanol, chloroform, acetone, methyl ethyl ketone, ethyl acetate, dioxane and tetrahydrofuran. The solvent composition was fixed so as to elute all of the components of the sample mixture in a practical period of 2 h. Satisfactory separation of the ten components was obtained with the n-hexane-ethanol (90:10) system. The presence of methanol as a modifier in the n-hexane was effective in reducing the elution time, but the separation was not as satisfactory. Chloroform or dioxane was useful only for the separation of Ser, Asn and Gln. Acetone, methyl ethyl ketone, ethyl acetate and tetrahydrofuran were not suitable for practical separations of Dns-amino acids.     

Gravimetric analysis of membrane casting : I. Cellulose acetate — acetone binary casting solutions

Solvent evaporation from cellulose acetate solutions cast to a thickness of 100–500 μ m is followed gravimetrically at 12–28°C. The desolvation curves include a region in which ω (solvent/polymer weight ratio) decreases almost exponentially with time. The exponential decrease lasts, at 28°C, until 75–85% solvent has evaporated, whereas below 19°C, upward bending in the log w vs. t relation is observed after evaporation of about half the solvent. The time constant of desolvation, τ, increases with the initial acetone weight per unit area, d, as τ α d^γ, where γ = 1.4–1.6. About a threefold increase in τ is observed on decreasing temperature from 28 to 12°C. Numerical solutions of the diffusion equation are obtained by taking time-dependence of surface solvent concentration and movement of the solution/air interface into account. The experimental facts are shown to be explicable by comparison with calculations. The effectiveness of the gravimetric approach to an understanding, characterization, and control of membrane casting processes is discussed.     

Conformational transitions of poly(β-benzyl L-aspartate)

Conditions that affect the conformation of poly(β-benzyl L-aspartate) in films have been studied. A slow transition from the left-handed to the right-handed α-helical form is observed under certain conditions in half-dried film cast from chloroform solutions and after exposure of amorphous films of the left-handed β-helical form to chloroform vapor. This transition is caused by adsorption of moisture. Thermal transitions of these films were examined by differential scanning calorimetry and infrared spectroscopy. The right-handed α-helices change to left-handed ω-helices around 140°C, and sharp exothermic peak is observed in this region for some films.     

聚(3-己基)噻吩薄膜中电荷传导的研究

对两种具有相同化学结构的聚(3-己基)噻吩膜进行了电荷传导研究以检验膜的结构对载流子迁移率的影响. 一种膜是由3-己基噻吩单体经电化学合成直接制备的膜(原位生长膜); 另一种膜是将原位生长膜溶于三氯甲烷后重新滴涂而成的(滴涂膜). 研究表明, 虽然两种膜的制备方法不一样, 但在最低(0.02%)和较高(20%～30%)掺杂率下两膜中的载流子迁移率相一致; 然而在中等掺杂率区域, 两膜中的载流子迁移率明显不同. 对于原位生长膜, 载流子迁移率在低掺杂区域几乎保持不变, 当掺杂率大于1%后开始上升; 而在滴涂膜中, 随着掺杂率的增加, 迁移率先下降然后迅速升高. 上述两种迁移率变化特征分别与以前研究中观察到的电化学合成高分子膜和化学合成高分子旋涂或滴涂膜中迁移率的变化特征相一致, 表明了迁移率随掺杂率变化特征的改变是由膜的结构变化而引起的     

Permeation through homopolymer latex films

The helium permeabilities of homopolymer films cast from polymer solutions and latex dispersions have been measured as a function of time. The permeability coefficients of most polymer latex films started off at a value which was considerably higher than that of the corresponding solvent-cast film, but then dropped at a rate dependent on the polymer concerned. The permeability coefficients levelled off at a value which was closer to, but still higher than that of the equivalent solvent-cast film. Solvent-cast film permeabilities remained constant for the period of several months over which time they were examined. The reduction in the permeability of latex films is attributed to ageing processes occurring within the film after casting. The fact that latex film permeability coefficients are always higher than those of solvent-cast films suggests that latex films never become completely homogeneous. The effect on permeability of the latex type and characteristics, and preparation and storage conditions has been examined. The polymer molecular weight, particle size, and surface-change density did not appear to exert any influence, within experimental error. However, the time-dependent permeability behavior was affected by the film preparation and storage temperatures.     

Gas permeability and hydrocarbon solubility of poly[1‐phenyl‐2‐[p‐(triisopropylsilyl)phenyl]acetylene]

The effects of film thickness, physical aging, and methanol conditioning on the solubility and transport properties of glassy poly[1‐phenyl‐2‐[p‐(triisopropylsilyl) phenyl]acetylene] are reported at 35 °C. In general, the gas permeability coefficients are very high, and this polymer is more permeable to larger hydrocarbons (e.g., C₃H₈ and C₄H₁₀) than to light gases such as H₂. The gas permeability and solubility coefficients are higher in as‐cast, unaged films than in as‐cast films aged at ambient conditions and increase to a maximum in both unaged and aged as‐cast films after methanol conditioning. For example, the oxygen permeability of a 20‐μm‐thick as‐cast film is initially 100 barrer and decreases to 40 barrer after aging for 1 week at ambient conditions. After methanol treatment, the oxygen permeabilities of unaged and aged films increase to 430 and 460 barrer, respectively. Thicker as‐cast films have higher gas permeabilities than thinner as‐cast films. Propane and n‐butane sorption isotherms suggest significant changes in the nonequilibrium excess free volume in these glassy polymer films due to processing history. For example, the nonequilibrium excess free volume estimated from the sorption data is similar for as‐cast, unaged samples and methanol‐conditioned samples; it is 100% higher in methanol‐conditioned films than in aged, as‐cast films. The sensitivity of permeability to processing history may be due in large measure to the influence of processing history on nonequilibrium excess free volume and free volume distribution. The propane and n‐butane diffusion coefficients are also sensitive to film processing history, presumably because of the dependence of diffusivity on free volume and free volume distribution. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1474–1484, 2000     

Effect of crystallization on the morphologies of block copolymer/homopolymer blends cast in an electric field

Blends of polystyrene (PS) and poly(styrene-b-ethylene oxide) (PS-b-PEO) were cast from a ternary solvent mixture containing 85% toluene, 10% tetrahydrofuran, and 5% methanol under conditions that favor crystallization of the PEO phase. Electric fields (2–14 kV/cm) were applied during casting to explore the possibility of morphology control by the field. It was observed that films cast in the absence of an electric field, in the temperature range of 0–25°C, from solutions initially cooled to 0°C were translucent. Their transmission electron micrographs exhibited thread-like, fibrillar structures. Micrographs of films cast in dc fields of 2–14 kV/cm at 16.3 ± 0.4°C also showed fibrillar structures, with the fibrils in the presence of fields greater than 8 kV/cm being substantially oriented in the field direction. We suggest that the morphologies developed under these conditions result from crystallization from preexisting crystal nuclei in the cooled solutions with the fibrillar crystals being oriented by the electric field. This method provides a possible way of processing anisotropic polymer blends. © 1996 John Wiley & Sons, Inc.     

Effect of Bee Pollen on the Mechanical and Thermal Properties of Starch Films

The use of casein, starch and bee pollen as biodegradable materials has been promise. The objective of this work was the development and characterization of films containing casein, pollen and starch. The films were obtained by casting process and the solvent evaporation was performed at 40 °C/24 h. The films characterization was carried out by microscopy, thermal analysis, opacity test, mechanical properties and barrier methods. The starch films presented heterogeneous on microscopy analysis. The thermal behaviors of pollen films were similar. The formulation containing only pollen 3% was unable to form film. The introduction of pollen in starch film formulation improved the mechanical characteristic and thermal stability of films.     

Structure and properties of a styrene–butadiene–styrene block copolymer

Electron-microscopic texture and physical properties of a styrene–butadiene–styrene (SBS) block copolymer obtained by casting from toluene, carbon tetrachloride, ethyl acetate, and methyl ethyl ketone are discussed. Two peaks are observed in the mechanical loss (tan delta;) curve at ?70 and 100°C which are attributed to segmental motion of polybutadiene and polystyrene, respectively. The polybutadiene peak heights are in the order of solubility in the solvent used; the polystyrene peak heights are in converse order. In addition to these peaks, a third peak is observed at 10°C for specimens cast from ethyl acetate or methyl ethyl ketone. A transition corresponding to this peak is also noticed in thermal analysis. It is proposed that aggregation of styrene blocks is relatively incomplete in specimens cast from solution in poor solvents.