Analysis of paroxetine, fluoxetine and norfluoxetine in fish tissues using pressurized liquid extraction, mixed mode solid phase extraction cleanup and liquid chromatography-tandem mass spectrometry

Recent studies have shown that selective serotonin reuptake inhibitors (SSRIs) such as fluoxetine are accumulated in the tissues of fish as a result of discharges of pharmaceuticals into surface waters from municipal wastewater treatment plants. In this study, an analytical method based on liquid chromatography with atmospheric pressure chemical ionization and tandem mass spectrometry (LC-APCI-MS/MS) was developed and validated for the determination of residues of paroxetine, fluoxetine and its active metabolite, norfluoxetine, in fish tissue. The procedure for sample preparation includes extraction of tissue by pressurized liquid extraction (PLE), followed by cleanup on a mixed-mode solid phase extraction (SPE) cartridge, Oasis MCX. With the optimized method, matrix interferences were reduced and recoveries >85% were obtained. The limits of quantitation (LOQ) determined by analysis of spiked fish tissue were 0.24, 0.07, and 0.14 ng/g wet weight for paroxetine, fluoxetine and norfluoxetine, respectively. This method was successfully applied to the analysis of samples of fish collected from Hamilton Harbour in Ontario, Canada, which is an urbanized and industrialized embayment of Lake Ontario. These analyses showed that the three analytes were present in fish tissues at concentrations up to approximately 1 microg/kg wet weight.     

Gas chromatography–mass spectrometry screening methods for select UV filters,synthetic musks,alkylphenols, an antimicrobial agent,and an insect repellent in fish

Two screening methods have been developed for simultaneous determination of ten extensively used personal care products (PCPs) and two alkylphenol surfactants in fish. The methods consisted of extraction, clean-up, derivatization and analysis by gas chromatography–mass spectrometry with selected ion monitoring (GC–SIM–MS) or gas chromatography–tandem mass spectrometry (GC–MS/MS) techniques. Among solvents tested to assess recovery of target compounds from 1-g tissue homogenates, acetone was selected as optimal for extracting compounds with dissimilar physicochemical properties from fish tissue. Initial experiments confirmed that GC–SIM–MS could be applied for analysis of lean fillet tissue (<1% lipid) without gel-permeation chromatography (GPC), and this approach was applied to assess the presence of target analytes in fish fillets collected from a regional effluent-dominated stream in Texas, USA. Benzophenone, galaxolide, tonalide, and triclosan were detected in 11 of 11 environmental samples at concentrations ranging from; 37 to 90, 234 to 970, 26 to 97, and 17 to 31 ng/g, respectively. However, performance of this analytical approach declined appreciably with increasing lipid content of analyzed tissues. Successful analysis of samples with increased lipid content was enabled by adding GPC to the sample preparation protocol and monitoring analytes with tandem mass spectrometry. Both analytical approaches were validated using fortified fillet tissue collected from locations expected to be minimally impacted by anthropogenic influences. Average analyte recoveries ranged from 87% to 114% with RSDs <11% and from 54% to 107% with RSDs <20% for fish tissue containing <1% and 4.9% lipid, respectively. Statistically derived method detection limits (MDLs) for GC–SIM–MS and GC–MS/MS methodologies ranged from 2.4 to 16 ng/g, and 5.1 to 397 ng/g, respectively.     

Extraction of polycyclic aromatic hydrocarbons from smoked fish using pressurized liquid extraction with integrated fat removal

Quantification of polycyclic aromatic hydrocarbons (PAHs) in smoked fish products often requires multiple clean-up steps to remove fat and other compounds that may interfere with the chemical analysis. We present a novel pressurized liquid extraction (PLE) method that integrates exhaustive extraction with fat retention in one single analytical step. The PLE parameters: type of fat retainer, flush volume, solvent composition, fat-to-fat retainer ratio (FFR), and the dimensions of the extraction cells were the most important factors for obtaining fat-free extracts with high recoveries of PAHs. A 100 mL extraction cell filled with 18 g activated silica gel, dichloromethane:hexane (15:85, v/v) as extraction solvent, FFR of 0.025 and 100% flush volume was the best analytical setup for integrated extraction and fat retention.The one-step procedure provided a more rapid and cost-efficient alternative with minimization of waste generation compared to the standard reference method that is based on a multi-step procedure. Furthermore, the analytical quality of the two methods are comparable, while the new integrated approach for extraction and cleanup is less prone to analytical errors (random and systematic) because of fewer analytical steps.     

Determination of pharmaceuticals, iodinated contrast media and musk fragrances in sludge by LC/tandem MS and GC/MS

Analytical methods have been developed that allow for the determination of antiphlogistics, lipid regulators, the antiepileptic carbamazepine, cytostatic agents, the psychiatric drug diazepam and iodinated contrast media (ICM) as well as two major polycyclic musk fragrances HHCB (galaxolide) and AHTN (tonalide) in activated and digested sludge. The procedures consist of ultrasonic solvent extraction (USE) using methanol/acetone or pressurized liquid extraction (PLE) using 100% methanol. Clean-up was performed with C18ec material and silica gel followed by LC tandem MS (electrospray or atmospheric pressure chemical ionization) detection for pharmaceuticals and iodinated contrast media as well as GC/MS in the SIM mode for musk fragrances. Absolute recoveries from spiked activated sludge in general ranged from 88+/-4 to 119+/-20% for ICM and were 78+/-15 and 87+/-10% for the AHTN and HHCB, respectively. For the pharmaceuticals, absolute recoveries in activated sludge ranged between 43 and 78%. Subsequently, compensation of losses was carried out by using surrogate standards (acidic pharmaceuticals: fenoprop, neutral pharmaceuticals: dihydro-carbamazepine, musk fragrances: AHTN-D3). With one exception the recoveries were also adequate in digested sludge ranging from 43% to 120%.     

Determination of pharmaceuticals in soils and sediments by pressurized liquid extraction and liquid chromatography tandem mass spectrometry

The present work describes the development of a sensitive analytical method based on pressurized liquid extraction (PLE) and pre-concentration by solid-phase extraction (SPE), followed by liquid chromatography–electrospray tandem mass spectrometry (LC–ESI-MS/MS) for the determination of seventeen pharmaceuticals in soils and sediments. The method is based on sample homogenisation using Na₂–EDTA washed sand and extraction with water at 90 °C. Special emphasis was placed on the optimization of the extraction procedure to develop a green method that reduces, at a maximum, the use of organic solvents in order to eliminate matrix components during the clean-up. The proposed method was linear in a concentration range from 0.3 to 333 ng g⁻¹, with correlation coefficients higher than 0.993. Method detection (MDLs) and quantification (MQLs) limits ranged from 0.1 to 6.8 ng g⁻¹ and from 0.25 to 23 ng g⁻¹, respectively. Absolute recoveries were analyte dependent, varying between 50% and 105% at the MQL level, except for fenofibrate (40%) and diclofenac (34%). The intra-day and inter-day precision was given by RSD values from 0.7% to 7.9% and from 1.6% to 14.5%, respectively. Acetaminophen, carbamazepine, ciprofloxacin, clofibric acid, codeine, diazepam, fenofibrate, metropolol, ofloxacin and propanolol were detected at concentrations from MDL to 35.62 ng g⁻¹ in soils and sediments from marsh areas. Due to the low recoveries, results for fenofibrate and diclofenac can only be considered as semi-quantitative. The method was fully suitable for the other 15 pharmaceuticals.     

Suitability of selective pressurized liquid extraction combined with gas chromatography-ion-trap tandem mass spectrometry for the analysis of polybrominated diphenyl ethers

A one-step extraction and clean-up method using pressurized liquid extraction (PLE) (selective PLE) combined with gas chromatography-ion-trap tandem mass spectrometry (GC-ITMS-MS) was evaluated for the analysis of polybrominated diphenyl ethers (from tri- to hepta-PBDEs) at low concentrations in fish and shellfish samples. To this end, the performance of an on-line PLE extraction/clean-up method and of a classical Soxhlet extraction and clean-up method using a multi-layer modified silica column were compared. The two sample treatment methods provided similar results, although an important reduction in the sample treatment time (40 min per sample) was achieved using the selective PLE method. In addition, the suitability of the PLE combined with GC-ITMS-MS method was evaluated by comparing the results obtained in the analysis of fish samples with those obtained by gas chromatography-high resolution mass spectrometry (GC-HRMS). Good agreement between both techniques was obtained with differences between the mean values of less than 16%. The selective PLE method coupled to GC-ITMS-MS produced accurate results for PBDE determination with low limits of detection (1.0-16.8 pg g⁻¹ wet weight) and quantification (3.1-51 pg g⁻¹ wet weight) as well as good precision (RSD < 16%). This method has been applied to the analysis of PBDEs in fish and shellfish samples collected at fish markets in Catalonia (NE Spain).     

Determination of 3-trifluoromethyl-4-nitrophenol and 3-trifluoromethyl-4-nitrophenol glucuronide in edible fillet tissue of rainbow trout and channel catfish by solid-phase extraction and liquid chromatography

3-Trifluoromethyl-4-nitrophenol (TFM) is a pesticide used for the selective control of sea lampreys (Petromyzon marinus) in stream and river tributaries of the Great Lakes. To determine concentrations of TFM and TFM glucuronide in the edible fillet tissue of fish during sea lamprey control treatments, an analytical method was developed to determine the concentrations of these residues in rainbow trout (Oncorhynchus mykiss; RBT) and channel catfish (Ictalurus punctatis; CCF). Homogenized fillets were extracted with methanol-water (80 + 20). TFM and TFM glucuronide were isolated from coextractives by C18 solid-phase extraction. TFM glucuronide was hydrolyzed to TFM by the addition of beta-glucuronidase to the TFM glucuronide extract. The extracts were analyzed separately by liquid chromatography with UV-visible detection. Recoveries from TFM-fortified CCF and RBT tissues were 84.1 and 96.1%, respectively. The method detection limits (MDLs) are 2.4 ng/g for TFM-fortified tissues of CCF and 3 ng/g for those of RBT. Recoveries were 78.8 and 77% from TFM glucuronide-fortified CCF and RBT tissues, respectively. The MDLs for TFM glucuronide-fortified tissues are 3.5 and 6.9 ng/g for CCF and RBT, respectively.     

Assessment of the occurrence and distribution of pharmaceuticals in a Mediterranean wetland (L'Albufera, Valencia, Spain) by LC-MS/MS

The distribution of 17 pharmaceuticals between water and the solid phase (sediments and soils) was studied by utilizing solid-phase extraction (SPE) and liquid chromatography?Ctandem mass spectrometry (LC-MS/MS). Two extraction procedures for soils and sediments, prior to the SPE, one based on pressurized liquid extraction (PLE) with hot water and the other on methanol/water ultrasonic extraction, were compared. Absolute recoveries were 71.2?C99.3% [relative standard deviation (RSD) <21.4%)] for water, and the method detection limits (MDLs) ranged from 0.3 to 10?ng?L^?1. Recoveries were 35.4?C105.3% (RSDs <19.1%) and 42.1?C97.8% (RSDs <14%) for soil and sediment samples, respectively, using PLE and 20.2?C86.5% (RSDs <25.1%) and 30.3?C97.4% (RSDs <19.1%) using ultrasonic extraction. Fifteen of the 17 pharmaceuticals were present in the L??Albufera water at concentrations up to 17???g?L^?1. Oxytetracycline and tetracycline were not detected. In sediments, only tetracycline, norfloxacin and diclofenac were not found. The other studied pharmaceuticals were present in the range from less than the method quantification limit (MQL) to 35.83?ng?g^?1. Among the 17 target compounds, ofloxacin, ciprofloxacin, norfloxacin, trimethoprim, clofibric acid and diclofenac were not detected in soil samples. The average concentrations ranged from less than the MQL for ibuprofen to 34.91?ng?g^?1 for tetracycline. These results indicate that pharmaceuticals could survive the wastewater treatment processes, which could lead to their dissemination in water environments.     

Pressurized liquid extraction of pharmaceuticals from sewage-sludge

A method for the quantitative determination of ten pharmaceuticals in sewage sludge was developed by using pressurized liquid extraction (PLE) and HPLC-MS with ESI (HPLC-(ESI)MS). The PLE was optimized with regard to solvents and operational parameters, such as temperature, pressure, extraction time, and purge time. The optimum conditions were: 50 mM phosphoric acid/methanol (1:1 v/v) as the extraction solvent, temperature of 100 degrees C, pressure of 100 bar, extraction time 15 min, 2 cycles, flush volume 150% and purge time 300 s. All recoveries for pharmaceuticals were over 68% except for salicylic acid. The repetitivity and reproducibility between days expressed as RSD was lower than 8% for repetitivity and 10% for reproducibility. The LOD of all compounds was lower than 10 microg/kg of dry weight of sewage sludge. The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants (STPs). The samples were collected every three months between February 2004 and June 2005. Some pharmaceuticals were determined in the samples and naproxen showed the highest value (242 microg/kg of dry weight).     

Determination of polycyclic aromatic compounds in fish tissue

A method is presented for the analysis of polycyclic aromatic hydrocarbons (PAHs), polycyclic aromatic sulfur heterocycles (PASHs), and basic polycyclic aromatic nitrogen heterocycles (PANHs) in fish. The analytical procedure includes Soxhlet extraction of prepared fish tissue with methylene chloride followed by gel permeation chromatography (GPC) using Bio-beads SX-3. For PAHs/PASHs, further cleanup is performed using adsorption chromatography on Florisil (5% water deactivated) and elution with hexane. For basic PANHs further cleanup of the fish extracts after GPC is achieved using liquid-liquid partitioning with 6 M hydrochloric acid and chloroform and then basifying the aqueous phase and extracting it with chloroform. Analysis of fortified fish samples was performed using capillary gas chromatography with flame ionization detection and capillary gas chromatography-mass spectrometry. Good agreement was observed for both methods of analysis when applied to fish samples fortified with PAHs, PASHs and basic PANHs at 0.1 to 1 microgram/g, suggesting that the method is effective at removing interfering biogenic compounds prior to analysis. Average recovery of PAHs/PASHs from fortified fish tissue was 87% and 70% for fish tissue fortified at 0.24-1.1 and 0.024-0.11 microgram/g, respectively. Average recovery for basic PANHs was 97% for fish fortified at 1.2-1.4 micrograms/g.     

Development and characterization of a solvent extraction-gas chromatographic/mass spectrometric method for the analysis of perfluorooctanesulfonamide compounds in solid matrices

A method utilizing solvent extraction and analysis by gas chromatography-positive chemical ionization mass spectrometry (SE-GC-PCIMS) was developed for the analysis of three neutral hydrophobic perfluorooctanesulfonamide compounds [perfluorooctanesulfonamide (PFOSA), N-ethyl perfluorooctanesulfonamide (N-EtPFOSA), and N,N-diethyl perfluorooctanesulfonamide (N,N-Et2PFOSA)]. These compounds are suspected metabolic precursors of perfluorooctane sulfonate. The SE-GC-PCI-MS method was used to analyze all three perfluorooctanesulfonamides in fast food, fish, and Arctic marine mammal liver samples. The SE-GC-PCI-MS method produced relatively higher recoveries of the analytes (averaging 83 +/- 6%, 84 +/- 9%, and 89 +/- 19% for N,N-Et2PFOSA, N-EtPFOSA, and PFOSA, respectively) with lower coefficients of variation, and less susceptibility to matrix effects, than ion pair extraction-liquid chromatography-tandem mass spectrometric methods. Method detection limits (MDLs) were 100, 120, and 250 pg/g for N,N-Et2PFOSA, N-EtPFOSA, and PFOSA, respectively. The three compounds were found at concentrations ranging from below the MDL to 22 ng/g wet weight in fast food, fish, and Arctic marine mammal liver samples.     

Determination of pharmaceuticals in biosolids using accelerated solvent extraction and liquid chromatography/tandem mass spectrometry

An analytical method was developed to quantitatively determine pharmaceuticals in biosolid (treated sewage sludge) from wastewater treatment plants (WWTPs). The collected biosolid samples were initially freeze dried, and grounded to obtain relatively homogenized powders. Pharmaceuticals were extracted using accelerated solvent extraction (ASE) under the optimized conditions. The optimal operation parameters, including extraction solvent, temperature, pressure, extraction time and cycles, were identified to be acetonitrile/water mixture (v/v 7:3) as extraction solvent with 3 extraction cycles (15 min for each cycle) at 100 °C and 100 bars. The extracts were cleaned up using solid-phase extraction followed by determination by liquid chromatography coupled with tandem mass spectrometry. For the 15 target pharmaceuticals commonly found in the environment, the overall method recoveries ranged from 49% to 68% for tetracyclines, 64% to 95% for sulfonamides, and 77% to 88% for other pharmaceuticals (i.e. acetaminophen, caffeine, carbamazepine, erythromycin, lincomycin and tylosin). The developed method was successfully validated and applied to the biosolid samples collected from WWTPs located in six cities in Michigan. Among the 15 target pharmaceuticals, 14 pharmaceuticals were detected in the collected biosolid samples. The average concentrations ranged from 2.6 μg/kg for lincomycin to 743.6 μg/kg for oxytetracycline. These results indicated that pharmaceuticals could survive wastewater treatment processes, and accumulate in sewage sludge and biosolids. Subsequent land application of the contaminated biosolids could lead to the dissemination of pharmaceuticals in soil and water environment, which poses potential threats to at-risk populations in the receiving ecosystems.     

Comparison of different cleanup procedures for oil crops based on the development of a trace analytical method for the determination of pyraclostrobin and epoxiconazole

The effects of different cleanup procedures in removing high‐molecular‐mass lipids and natural colorants from oil‐crop extracts, including dispersive solid‐phase extraction, low‐temperature precipitation and gel permeation chromatography, were studied. The pigment removal, lipid quantity, and matrix effects of the three cleanup methods were evaluated. Results indicated that the gel permeation chromatography method is the most effective way to compare the dispersive solid‐phase extraction and low‐temperature precipitation. Pyraclostrobin and epoxiconazole applied extensively in oil‐crop production were selected as typical pesticides to study and a trace analytical method was developed by gel permeation chromatography and ultra high performance liquid chromatography with tandem mass spectrometry. Average recoveries of the target pesticides at three levels (10, 50, and 100 μg/kg) were in the range of 74.7–96.8% with relative standard deviation values below 9.2%. The limits of detection did not exceed 0.46 μg/kg, whereas the limits of quantification were below 1.54 μg/kg and much lower than maximum residue limit in all matrices. This study may provide the essential data for optimizing the analytical method of pesticides in oil‐crop samples.     

Multiresidue method for the determination of 32 human and veterinary pharmaceuticals in soil and sediment by pressurized-liquid extraction and LC-MS/MS

An analytical chemical method has been developed for the simultaneous determination of 32 different pharmaceuticals in soils and sediments. The pharmaceuticals cover a varity of different compound groups. Soil samples were extracted with different solvents with the help of pressurized-liquid extraction (PLE) followed by clean-up using a solid-phase extraction (SPE) procedure. The purified extracts were analyzed by LC-MS/MS. The extraction method was evaluated by testing the following variables: extraction solvents, solvent pH, and temperature. Applying 20 g of soil/sediment and extracting with a mixture of methanol with aqueous ammonia solution (0.1 mol L^?1) at 80?°C for 5 min in five cycles provided satisfactory recoveries between 66 and 114% with SD of between 1 and 14%. For preconcentration and purification tandem MAX-HLB cartridges were used. The volume and composition was optimized and the highest recoveries were obtained with a combination of methanol—aqueous ammonia solution. The limits of quantification (LOQs) were between 0.2 and 2 ng g^?1 and linearity higher than 0.98 for the majority of the selected pharmaceuticals. The method was successfully applied to soil samples collected from the Jerez de la Frontera agricultural region, irrigated with treated wastewater, and to sediment samples from the River Guadalete. The detection of nine pharmaceuticals including stimulants, antirheumatics, analgesics, anti-inflammatories, tranquilizers, and veterinary medicines at ng g^?1 concentration levels was achieved.     

Determination of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in soils by pressurized liquid extraction and liquid chromatography-electrospray ionization mass spectrometry

To aid in the evaluation of the potential toxicity of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), we describe a pressurized liquid extraction (PLE) followed by liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS) method for determination of RDX and its N-nitroso derivatives: hexahydro-1-nitroso-3,5-dinitro-1,3,5-triazine (MNX), hexahydro-1,3-dinitroso-5-nitro-1,3,5-triazine (DNX), and hexahydro-1,3,5-trinitroso-1,3,5-triazine (TNX) in soils. Sandy loam soil was spiked with RDX and its N-nitroso derivatives (MNX, DNX, and TNX). Acetonitrile was used as the PLE extraction solvent at 100 degrees C and 1500 psi for 15 min. Florisil was used to cleanup extracts following PLE. Instrumental analysis employed LC-ESI-MS, in which 1mM acetic acid was added to the mobile phase to facilitate formation of acetate adduct ions [M+CH(3)COO](-). The method detection limits (MDLs) for RDX, MNX, DNX, and TNX were 1.46, 1.46, 1.69, and 1.93 ng/g, respectively. High recovery (91.1-108.3%), good precision (RSD: 3.2-12.4%), and reproducibility were achieved. This method proved effective and was applied to monitor the reductive biotransformation of MNX in soils with the presence of earthworms (Eisenia fetida).     

Extraction and analysis of pharmaceuticals in polluted sediment using liquid chromatography mass spectrometry

A multi-residue method for the extraction and clean-up of sediment samples was developed for the analysis of pharmaceutical residues. Sediment samples were collected in the proximity of sewage water plant in Stockholm, Sweden. Target analytes were the basic β-blocker propranolol, the neutral neuroleptic carbamazepine and the acidic anticoagulant warfarin, the painkiller diclofenac and the lipid regulator gemfibrozil. The extraction solvent was optimised with regard to pH and organic modifer. Extraction and clean up were performed with liquid-liquid extraction and ultra-sonication followed by solid-phase extraction. One extraction solvent, containing acetone/McIlvaine buffer pH4, provided satisfactory extraction for all substances. LC/MSMS in the MRM mode was used for determination. The recoveries of the extraction and clean-up steps were 60–75% (±2–8%) and LOQs were in the range 0.4–8?ng/g sediment (dry weight). The pharmaceuticals found in the sediment samples were propranolol and carbamazepine, representing substances with basic and neutral properties. Additionally, the samples were analysed with LC/QTOF for verification with the use of accurate mass measurement in the full-scan mode. Pharmaceuticals not represented in the original method were looked for. Non-target pharmaceuticals found using the LC/QTOF system were the basic β-blocker metoprolol and the acidic painkiller naproxen.     

Comparison of multiple API techniques for the simultaneous detection of microconstituents in water by on‐line SPE‐LC‐MS/MS

This study described a fully automated method using on‐line solid phase extraction of large volume injections coupled with high performance liquid chromatography (HPLC) and tandem mass spectrometry (MS/MS) to simultaneously detect a group of recalcitrant microconstituents (pharmaceuticals and personal care products, steroid hormones and sterols) in aqueous matrices. Samples (1 mL to 20 mL) were loaded to the preconcentration column at 1 mL/min, and the column was washed with 1000 μL of 25% methanol in LC/MS water to remove polar and ionic interferences before LC‐MS/MS analysis. Three different atmospheric pressure ionization (API) techniques, including photoionization (APPI) with four different dopants (acetone, anisole, chlorobenzene and toluene), heated electrospray ionization (HESI) and atmospheric pressure chemical ionization (APCI), were evaluated on the basis of method detection limits (MDLs) and recoveries from different aqueous matrixes. Results indicated that APPI with toluene as dopant was the most sensitive ionization method for the majority of the analytes. When using 5 mL of sample, MDLs for pharmaceuticals and personal care products, including carbamazepine, DEET, caffeine, naproxen, acetaminophen and primidone, were between 0.3 ng/L and 15 ng/L. MDLs of hormones, including testosterone, equilenin, progesterone, equilin, 17β‐estradiol, 17α‐ethynylestradiol, estrone, androsterone, mestranol and estriol, were between 1.2 ng/L and 37 ng/L. The combination of APPI with dopant allowed the detection of two difficult to ionize fecal related sterols, such as coprostan‐3‐ol and coprostan‐3‐one with MDLs of 5.4 ng/L and 11 ng/L, respectively. Calculated MDLs are more than adequate for analysis of wastewater using 1 to 5 mL sample size and for surface waters using up to 20 mL sample size. Copyright © 2012 John Wiley & Sons, Ltd.     

凝胶渗透色谱-固相萃取联合净化气相色谱-质谱联用法测定动物性食品中30种有机氯农药的残留量

建立了猪肉、鸡肉、鱼肉和虾肉等动物性食品中30种有机氯农药残留的气相色谱-质谱联用检测方法。样品匀浆后,采用乙腈提取,以凝胶渗透色谱和弗罗里硅土固相萃取柱联合进行净化,气相色谱-质谱检测,以同位素内标法定量。30种有机氯农药的响应在5.0~500.0 μg/L范围内呈良好的线性,相关系数在0.996以上,各有机氯农药的检出限在0.2~2.7 μg/kg之间。以猪肉、鸡肉、鱼肉和虾肉作为代表性基质,进行5.0、10.0、20.0 μg/kg 3个水平的加标回收试验,回收率在55.0%~119.1%之间,相对标准偏差在0.4%~15.0%之间。该方法准确可靠,灵敏度高,样品净化效果好,能够满足动物性食品中有机氯农药多残留痕量分析的要求。     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.     

Development of a pressurised liquid extraction and liquid chromatography with electrospray ionization-tandem mass spectrometry method for the determination of domoic acid in shellfish

Amnesic shellfish poisoning (ASP) is a potentially lethal human toxic syndrome which is caused by domoic acid (DA) that originates in marine phytoplankton belonging to the Pseudonitzschia genus. A confirmatory and sensitive procedure has been developed and validated for the determination of DA in shellfish. The proposed method includes pressurised liquid extraction (PLE) with methanol/acetone (9:1), florisil clean-up purification inside the PLE extraction cell and detection by liquid chromatography (LC) coupled to electrospray ionization in positive mode tandem mass spectrometry (ESI-MS-MS). Comparison of ionization sources (ESI, atmospheric pressure ionization (APCI) atmospheric pressure photoionization (APPI) and combined APCI/APPI) were carried out in order to improve the analytical signal. The main parameters affecting the performance of the different ionization sources and PLE parameters were previously optimised using statistical design of experiments (DOE). Linear calibrations were obtained using mussel tissue extracts 0.05-5 microg DA/ml (R2>0.999). The limits of detection (LOD) and quantitation (LOQ) of the method were 0.2 and 0.5 microg/g respectively and recoveries ranged from 81 to 95%. This method was successfully applied to determine DA levels in 46 shellfish samples collected from Valencian (Spain) supermarkets, showing high sample throughput.