Photopolymerization of thiol‐ene systems based on oligomeric thiols

Thiol oligomers were copolymerized with a triallyl ether by a photoinduced polymerization process. These oligomeric thiol‐ene systems comprise the same components as a photopolymerized thiol‐ene‐acrylate ternary system, yet the photopolymerized networks have much lower glass transition temperatures. An investigation into the effect of oligomeric thiol design on network formation was conducted by analyzing the reaction kinetics and thermal/mechanical properties of the thiol‐ene networks. Real‐time FTIR analysis shows that total conversion is >90% for all thiols investigated. Photo‐DSC analysis shows that the maximum exotherm rate is roughly equivalent for all of the thiols when the equivalent weight of the thiol is taken into account. As would be expected, the glass transition temperature and tensile strength increase with thiol functionality and lower thiol equivalent weight for thiols with functionality from 2 to 4. Films made using the oligomeric thiols have essentially the same glass transition temperatures and tensile modulus values regardless of thiol design. These results distinguish the method for generation of networks consisting of an initial Michael reaction of thiols and acrylates followed by a photoinitiated copolymerization with a multifunctional ene from the traditional photolysis of the corresponding thiol‐ene‐acrylate ternary systems with no Michael reaction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 14–24, 2009     

Thiol‐ene photopolymerization for efficient curing of vinyl esters

Monomers for radical photopolymerization based on vinyl esters (VEs) have recently been identified as suitable alternatives to (meth)acrylates on account of their low irritancy and cytotoxicity. The drawback of most VEs with abstractable hydrogens is their relatively low reactivity compared with (meth)acrylates. Within this article, we proved by photo‐differential scanning calorimetry measurements and real‐time Fourier transform infrared spectroscopy that the thiol‐ene concept is able to improve the photoreactivity of these VEs to a large extent to a level between those of acrylates and methacrylates. Other VEs have now a reactivity of at least the level of similar acrylates. Mechanical properties as determined by Dynamic Mechanical Analysis and Charpy impact tests showed significant toughening of these materials. Furthermore, we were able to confirm low toxicity of all components by osteoblast cell culture experiments. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Evaluation of thiol‐ene click chemistry in functionalized polysiloxanes

Polysiloxanes are commonly used in a myriad of applications, and the “click” nature of the thiol‐ene reaction is well suited for introducing alternative functionalities or for crosslinking these ubiquitous polymers. As such, understanding of the thiol‐ene reaction in the presence of silicones is valuable and would lead to enhanced methodologies for modification and crosslinking. Here, the thiol‐ene reaction kinetics were investigated in functionalized oligosiloxanes having varying degrees of thiol functionalization (SH), π–π interactions (from diphenyls, DP), and ene types (C?C). In the ene‐functionalized oligomers, π–π interactions were controlled through the use of dioctyl repeats (DO). The polymerization rate and rate‐limiting steps were determined for all systems containing an allyl‐functionalized oligomer, and rates ranging from 0.10 to 0.54 mol L^?1 min^?1 were seen. The rate‐limiting step varied with the oligomer composition; examples of rate‐limited propagation (5:3:2 C?C:DP:DO/1:1 SH:DP) or chain transfer (5:3:2 C?C:DP:DO/3:1 SH:DP) were found in addition to cases with similar reaction rate constants (5:2:3 C?C:DP:DO/1:1 SH:DP). None of the siloxanes were found to exhibit autoacceleration despite their relatively high viscosities. Instead, the allyl‐, vinyl‐, and acrylate‐functionalized siloxanes were all found to undergo unimolecular termination based on their high α scaling values (0.98, 0.95, and 0.82, respectively) in the relation R_p ∝ R_i^α. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

An efficient nonisocyanate route to polyurethanes via thiol‐ene self‐addition

A novel and efficient strategy for the synthesis of nonisocyanate polyurethanes has been developed via thiol–ene self‐photopolymerization. An aliphatic thiol–ene carbamate monomer (allyl(2‐mercaptoethyl)carbamate, AMC) was synthesized by a one‐step synthesis procedure, from cysteamine and allyl chloroformate. The urethane group was therefore incorporated directly into the monomer precursor, avoiding the problems associated to toxic isocyanates. AMC was successfully stabilized with the radical inhibitor pyrogallol (1% wt). In addition, the use of phenyl phosphonic acid as coadditive allowed its stabilization for lower concentrations of pyrogallol (0.1% wt). AMC was directly transformed into thermoplastic polyurethane (TPU) through thiol–ene photopolymerization by UV‐irradiation at 365 nm. The obtained TPU presented semi‐crystalline nature and very high thermal stability (T_5% ～325 °C). It was found that high concentrations of pyrogallol decreased the reaction rate and final conversion of photopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3017–3025     

Thiol–ene polymerizations using imide‐based monomers

New diene and dithiol monomers, based on aromatic imides such as benzophenone‐3,3′,4,4′‐tetracarboxylic diimide were synthesized and used in thiol‐ene polymerizations which yield poly(imide‐co‐thioether)s. These linear polymers exhibit limited solubility in various organic solvents. The molecular weights of the polymers were found to decrease with increasing imide content. The glass transition temperature (T_g) of these polymers is dependent on imide content, with T_g values ranging from ?55 °C (with no imide) up to 13 °C (with 70% imide). These thermal property improvements are due to the H‐bonding and rigidity of the aromatic imide moieties. Thermal degradation, as studied by thermogravimetric analysis, was not significantly different to the nonimide containing thiol‐ene polymers made using trimethyloylpropane diallyl ether and 3,5‐dioxa‐1,8‐dithiooctane. It is expected that such monomers may lead to increased glass transition temperatures in other thiol‐ene polymer systems as these normally exhibit low glass transition temperatures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4637–4642     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Visible light‐induced thiol‐ene reaction: A new strategy to prepare Α,ω‐dithiol and Α,ω‐divinyl telechelic polythiolether oligomers

A new strategy is developed to prepare both α,ω‐dithiol and α,ω‐divinyl linear telechelic polythiolether oligomers by visible light induced thiol‐ene chemistry in the presence of a fac‐Ir(ppy)₃ photoredox catalyst. Polythiolether oligomers of well‐defined end groups and controlled molecular weights have been successfully synthesized at varying monomer molar ratios of 1,4‐benzenedimethanethiol (BDMT) to diethylene glycol divinyl ether (DEGVE). ¹H NMR and MALDI‐TOF MS analyses demonstrate that as‐prepared polythiolethers possess high end‐group fidelity, which is further supported by the successful polyaddition of polythiolethers bearing α,ω‐dithiol and α,ω‐divinyl groups. For example, with the α,ω‐dithiol‐ (M_n = 1900 g mol^?1, PDI = 1.25) and α,ω‐divinyl‐terminated (M_n = 2000 g mol^?1, PDI = 1.29) polythiolethers as macromonomers, the molecular weight of resulting polythiolether is up to 7700 g mol^?1 with PDI as 1.67. The reactivity of the terminal thiol group is further confirmed by the addition reaction with N‐(1‐pyrenyl)maleimide. UV‐vis spectra and fluorescene measurements suggest that fac‐Ir(ppy)₃ undergo a redox quenching process reacted with BDMT to generate thiyl free radicals. With these results, the mechanism of the thiol‐ene reaction catalyzed by photoredox catalyst is proposed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 740–749     

Synthesis and thiol–ene photopolymerization of allyl‐ether functionalized dendrimers

Well‐defined, allyl‐ether functional, first‐generation dendrimers have been synthesized. The convergent growth approach was utilized, using the anhydride of the allyl‐ether terminated building block. Three different core moieties were used: trimethylolpropane, trisphenol, and ditrimethylolpropane. The coupling reactions proceeded in good yields and all compounds were characterized by NMR, MALDI‐TOF, and SEC. The allyl‐terminated dendrimers were crosslinked by thiol–ene chemistry, using a multifunctional thiol, TriThiol, to give clear and smooth films. The photopolymerization was conducted in the presence of a photoinitiator, Irgacure 651, and no traces of either allyl‐ether groups or thiols were observed by FT‐Raman after cure. All crosslinked films were characterized with respect to mechanical (DMA) and thermal (DSC) properties. It was found that homogeneous networks were formed and that the core functionality and structure had little effect on the network properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1339–1348, 2008     

Thiourethane‐based thiol‐ene high Tg networks: Preparation,thermal, mechanical,and physical properties

Thiourethane‐based thiol‐ene (TUTE) films were prepared from diisocyanates, tetrafunctional thiols and trienes. The incorporation of thiourethane linkages into the thiol‐ene networks results in TUTE films with high glass transition temperatures. Increases of T_g were achieved by aging at room temperature and annealing the UV cured films at 85 °C. The aged/annealed film with thiol prepared from isophorone diisocyanate and cured with a 10,080‐mJ/cm² radiant exposure had the highest DMA‐based glass transition temperature (108 °C) and a tan δ peak with a full width at half maximum (FWHM) of 22 °C, indicating a very uniform matrix structure. All of the initially prepared TUTE films exhibited good physical and mechanical properties based on pencil hardness, pendulum hardness, impact, and bending tests. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5103–5111, 2007     

Living radical photopolymerization induced grafting on thiol–ene based substrates

The formation of reactive substrates with iniferter‐mediated living radical photopolymerization is a powerful technique for surface modification, which can readily be used to facilitate the incorporation of a variety of surface functionalities. In this research, the photopolymerization kinetics of novel bulk thiol–ene systems have been compared with those of typical acrylate and methacrylate systems when polymerized in the presence of the photoiniferter p‐xylene bis(N,N‐diethyl dithiocarbamate) (XDT). In the presence of XDT, the thiol–ene systems photopolymerize more quickly than the traditional acrylate and methacrylate systems by one to two orders of magnitude. Fourier transform infrared spectroscopy has been used to monitor the photografting kinetics of various monomers on dithiocarbamate‐functionalized surfaces. Furthermore, this technique has been used to evaluate surface‐initiation kinetics and to emphasize the influence of bulk substrate properties on grafting kinetics. Finally, photopatterning has been demonstrated on a dithiocarbamate‐incorporated thiol–ene substrate with conventional photolithographic techniques. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2134–2144, 2005     

The power of thiol‐ene chemistry

As a tribute to Professor Charlie Hoyle, we take the opportunity to review the impact of thiol‐ene chemistry on polymer and materials science over the past 5 years. During this time, a renaissance in thiol‐ene chemistry has occurred with recent progress demonstrating its unique advantages when compared with traditional coupling and functionalization strategies. Additionally, the robust nature of thiol‐ene chemistry allows for the preparation of well‐defined materials with few structural limitations and synthetic requirements. To illustrate these features, the utility of thiol‐ene reactions for network formation, polymer functionalization, dendrimer synthesis, and the decoration of three‐dimensional objects is discussed. Also, the development of the closely related thiol‐yne chemistry is described. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 743–750, 2010     

Exploring thiol‐yne based monomers as low cytotoxic building blocks for radical photopolymerization

The last decade has seen a remarkable interest in the development of biocompatible monomers for the realization of patient specific medical devices by means of UV‐based additive manufacturing technologies. This contribution deals with the synthesis and investigation of novel thiol‐yne based monomers with a focus on their biocompatibility and also the mechanical properties in their cured state. It could be successfully shown that propargyl and but‐1‐yne‐4‐yl ether derivatives have a significant lower cytotoxicity than the corresponding (meth)acrylates with similar backbones. Together with appropriate thiol monomers, these compounds show reactivities in the range of (meth)acrylates and almost quantitative triple bond conversions. A particular highlight is the investigation of the network properties of photo cured alkynyl ether/thiol resins by means of low field solid state nuclear magnetic resonance spectroscopy. Additionally, dynamic mechanical analysis of those polymers revealed that monomers containing rigid backbones lead to moduli and glass transition temperatures (T_g's), sufficiently high for the fabrication of medical devices by UV based additive manufacturing methods. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3484–3494     

Synthesis of main chain polymeric benzophenone photoinitiator via thiol‐ene click chemistry and Its use in free radical polymerization

Main chain polymeric benzophenone photoinitiator (PBP) was synthesized by using “Thiol‐ene Click Chemistry” and characterized with ¹H NMR, FTIR, UV, and phosphorescence spectroscopies. PBP as a polymeric photoinitiator presented excellent absorption properties (ε₂₉₄ = 28,300 mol^?1L^?1cm^?1) compared to the molecular initiator BP (ε₂₅₂ = 16,600 mol^?1L^?1cm^?1). The triplet energy of PBP was obtained from the phosphorescence measurement in 2‐methyl tetrahydrofurane at 77 K as 298.3 kJ/mol and according to phosphorescence lifetime, the lowest triplet state of PBP has an n‐π* nature. Triplet–triplet absorption spectrum of PBP at 550 nm following laser excitation (355 nm) were recorded and triplet lifetime of PBP was found as 250 ns. The photoinitiation efficiency of PBP was determined for the polymerization of Hexanedioldiacrylate (HDDA) with PBP and BP in the presence of a coinitiator namely, N‐methyldiethanolamine (MDEA) by Photo‐DSC. The initiation efficiency of PBP for polymerization of HDDA is much higher than for the formulation consisting of BP. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Effect of introducing a cationic system into a thiol‐ene photopolymerizable formulation

Hybrid materials derived from a thiol‐ene and cationic polymerization were obtained from concomitant polymerization. The hybrid materials were cured by both photopolymerization and thermally induced polymerization. The kinetics of the photopolymerization were measured using time resolved‐IR and optical pyrometry. The nucleophilic character of the polysulfide obtained initially in the thiol‐ene polymerization inhibited the development of the cationic photoinitiated polymerization of epoxy monomers. Besides, the epoxide groups underwent a proton catalyzed addition reaction with the thiols to form new sulfides groups in the reaction mixture. It is proposed that the formed sulfides can terminate the growing polyether chains forming dormant species like trialkylsulfonium salts. These salts promote the thermal polymerization of the epoxy monomer in a post treatment, producing hard and transparent materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4829–4843, 2007     

High‐molecular‐weight polyisobutylenes (PIBs) and PIB networks from liquid PIBs by thiol‐ene clicking

We report the synthesis of high‐molecular‐weight linear polyisobutylenes (PIBs) and PIB networks from low‐molecular‐weight PIB by thiol‐ene click chemistry. Thus, liquid allyl‐telechelic PIB was reacted with small di‐ and tri‐thiols, and the thiolated intermediates chain‐extended by UV‐ or thermally induced free radical initiation to linear and crosslinked products. PIB networks were also prepared by crosslinking SH‐telechelic PIB with a small triallyl compound. Linear products were characterized by ¹H NMR spectroscopy and GPC, and networks by FTIR spectroscopy, extractables, swelling, and permanent set. The effect of reaction conditions (nature of thiol chain extender, concentration of photo‐ and thermal initiators, UV radiation time, and reagent concentrations) on chain extension and crosslinking was investigated. Under well‐defined conditions high‐molecular‐weight PIBs and tight PIB networks were prepared. Thiol‐ene click chemistry provides novel thiolated PIB derivatives and is a useful strategy for the convenient preparation of high‐molecular‐weight rubbery PIBs and tight PIB networks from low‐molecular‐weight PIB precursors. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019     

Chemo‐ and stereoselective polymerization of 3‐methylenehepta‐1,6‐Diene and Its thiol‐ene modification

Here we report on the coordination polymerization of a vinyl‐functionalized butadiene monomer, 3‐methylenehepta‐1,6‐diene (MHD) with exclusive conjugated diene chemoselectivity, high 1,2‐regioselectivity and moderate isotacticity (1,2‐selectivity > 99%, mm triad = 93%). Random copolymers of MHD and other conjugated diene (isoprene or myrcene) are also synthesized. The pendent vinyl groups of MHD homo or copolymers could be quantitatively converted into various functional groups via thiol‐ene click reaction. The resulting functionalized polybutadiene‐based material display versatile thermal and surface properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1031–1039     

High‐throughput kinetic analysis of acrylate and thiol‐ene photopolymerization using temperature and exposure time gradients

In this work, a high‐throughput technique for evaluating photopolymers is developed to enable simultaneous measurement of the effects of temperature in combination with exposure time. Temperature and exposure time gradients were produced in orthogonal directions on a single sample, and subsequently sampled using Fourier transform infrared (FTIR) spectroscopy. The technique developed here allows for photopolymerization kinetics to be analyzed rapidly over a large range of industrially relevant temperatures, giving insight into the role temperature and the polymer's glass transition temperature have in dictating the photopolymerization kinetics. In the 70/30 wt % hexyl acrylate and hexanediol diacrylate system, conversion in samples below the glass transition temperature (T_G) was 66 ± 2% after 12 s, significantly lower than the 93 ± 4% conversion at 12 s for samples polymerized at temperatures above the T_G. In addition, a thiol‐ene system was analyzed to study the effect of temperature on the ene homopolymerization in allyl ether monomers, which leads to incomplete thiol conversion in stoichiometrically balanced systems. At a 60% thiol conversion, the allyl ether‐ene conversion at all temperatures is 65 ± 3% irrespective of initial formulation temperature, indicative of the homopolymerization behavior being nearly independent of temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1502–1509, 2008     

Antimicrobial equipment of poly(isoprene) applying thiol‐ene chemistry

The functionalization of anionically polymerized isoprene with cysteamine applying the thiol‐ene reaction is reported. Antimicrobial activity is implemented by quaternization of the amino functionality by either alkylation or by protonation. The resulting polymers were tested against Gram‐positive as well as Gram‐negative bacteria strains according to the Japanese Industrial Standard Z2801:2000 protocol, partly revealing excellent biocidal performance. Thermal stability up to 200°C allows extrusion processing of the functionalized poly(isoprene)s. The best performing polymer, that is, bearing butylated ammonium‐groups, was compounded with the commodity material poly(propylene). The compound bearing 5 wt % of the biocidal polymer exhibited satisfactory biocidal properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012