Transient bioelectronics: Electronic properties of silver microparticle‐based circuits on polymeric substrates subjected to mechanical load

Transient soft bioelectronics are capable of forming conformal contacts with curvilinear surfaces of biological host tissues and organs. Such systems are often subject to continuous static and dynamic loads from the biological host. In this article, we present investigation of electronic attributes of transient soft bioelectronic circuits subjected to mechanical force and influence of substrate's transiency on the transiency of the whole device; also, characterize and quantify loss of functionality in triggered devices. Variations in the electrical conductivity of circuits as a function of applied mechanical load was used as a means to deduce electronic characteristics under stress. The experimental results suggest that there exists a correlation between electronic properties of circuits and applied mechanical strain; no clear correlation was, however, observed between electronic properties of circuits and frequency of the applied dynamic load. Control over transiency rate of identical circuits utilizing the transiency characteristics of the poly(vinyl alcohol)l‐based substrates is also studied and demonstrated. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1603–1610     

Physical–chemical hybrid transiency: A fully transient li‐ion battery based on insoluble active materials

Transient Li‐ion batteries based on polymeric constituents are presented, exhibiting a twofold increase in the potential and approximately three orders of magnitude faster transiency rate compared to other transient systems reported in the literature. The battery takes advantage of a close variation of the active materials used in conventional Li‐ion batteries and can achieve and maintain a potential of >2.5 V. All materials are deposited form polymer‐based emulsions and the transiency is achieved through a hybrid approach of redispersion of insoluble, and dissolution of soluble components in approximately 30 min. The presented proof of concept has paramount potentials in military and hardware security applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2021–2027     

Brushless and controlled microphase separation of lamellar polystyrene‐b‐polyethylene oxide thin films for block copolymer nanolithography

Creating perpendicular alignment in lamellar block copolymer (BCP) systems has considerable industrial and commercial significance, most importantly for generating nanowire structures in electronic devices. In general, these lamellar systems require careful interface engineering to obtain vertical orientation of the blocks. To avoid the strong preferential adsorption of one block to either the substrate or the polymer/air interface, the surface must be “neutralized” by chemical brushes or external forces, for example, solvent fields. Reported here is a stepwise thermo/solvent annealing process allowing the formation of perpendicular domains of polystyrene‐b‐polyethylene oxide lamellar structures while avoiding brush or other surface modifications. This BCP has a relatively small minimum feature size and can be used to generate substrate patterns for use in fabrication of nanowire electronic device structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Oscillatory interaction between two like‐charged nanoparticles induced by polyelectrolyte brush–solvent interface

We use two‐dimensional (2D) self‐consistent field theory to study the effective interactions between two like‐charged cylindrical nanoparticles mediated by an oppositely weakly charged polyelectrolyte brush in a solvent solution. In a poor solvent, where a sharp brush–solvent interface forms, an oscillatory interaction is observed when two nanoparticles are both located at the brush–solvent interface. This oscillatory interaction depends on the penetration depths of the particles and their geometric orientations with respect to the substrate. When the particles are both immersed in the brush and/or the particles are oriented vertically or diagonally with large angles to the substrate, the oscillatory behavior disappears. We interpret our findings by analyzing in detail the contributions to the free energy from electrostatic interaction, nonelectrostatic interaction, and entropies, separately. Briefly, the deformations of the interface and the ion layers formed in the vicinity of the interface are responsible for this oscillatory behavior. In a good solvent, where the narrow brush–solvent interface vanishes, the effective particle–particle interactions behave like that for both particles immersed into the brush with poor solvent. They are found to be repulsive. The influences of the particle size, grafting density, and amount of charges and ions are also briefly discussed. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1458–1468     

New π‐Conjugated polymers containing 4H,4′H‐[1,1′‐Bithieno [3,4‐C]Pyrrole]‐4,4′,6,6′(5H,5′H)‐Tetraone (biTPD) units and their application to thin‐Film transistors and photovoltaic cells

We successfully synthesized new D‐A copolymers that employ 1,10‐bithienopyrrolodione (biTPD), thiophene, and selenophene‐based donor monomeric units. Two polymers, PBTPDEBT and PBTPDEBS , exhibited high degrees of crystallinity and unique polymer chain arrangements on the substrate, which is attributed to their enhanced coplanarity and intermolecular interactions between the polymer chains. Among the thin‐film transistor devices made of PBTPDEBT and PBTPDEBS , the annealed PBTPDEBS device displayed relatively high hole mobility, which was twice that of the PBTPDEBT ‐based device. In addition, an organic photovoltaic device based on a PBTPDEBS :PC₇₁BM blend displayed the maximum power conversion efficiency of 3.85%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1228–1235     

Multilayer films composed of conductive poly(3‐hydroxybutyrate)/carbon nanotubes bionanocomposites and a photoresponsive conducting polymer

In order to develop new electronic devices, it is necessary to find innovative solutions to the eco‐sustainability problem of materials as substrates for circuits. We realized a photoresponsive device consisting of a semiconducting polymer film deposited onto optically semitransparent and conductive biodegradable poly(3‐hydroxybutyrate) (PHB)/carbon nanotube (CNT) substrates. The experiments indicated that the PHB‐CNT bionanocomposite substrate behaves as an optical window trapping electric charges produced by the photoexcitation of the semiconducting polymer. Such PHB‐CNT functional substrates are expected to be attractive for eco‐friendly electronics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 596–602     

Investigation of polymer–solvent interactions in poly(styrene sulfonate) thin films

The swelling behavior of acid form poly(styrene sulfonate) (PSS‐H) thin films were investigated using in situ spectroscopic ellipsometry (SE) to probe the polymer–solvent interactions of ion‐containing polymers under interfacial confinement. The interaction parameter (χ), related to the polymer and solvent solubility parameters in the Flory–Huggins theory, describes the polymer‐solvent compatibility. In situ SE was used to measure the degree of polymer swelling in various solvent vapor environments, to determine χ for the solvent‐PSS‐H system. The calculated solubility parameter of 40–44 MPa^1/2 for PSS‐H was determined through measured χ values in water, methanol, and formamide environments at a solvent vapor activity of 0.95. Flory–Huggins theory was applied to describe the thickness‐dependent swelling of PSS‐H and to quantify the water‐PSS‐H interactions. Confinement had a significant influence on polymer swelling at low water vapor activities expressed as an increased χ between the water and polymer with decreasing film thickness. As the volume fraction of water approached ～0.3, the measured χ value was ～0.65, indicating the water interacted with the polymer in a similar manner, regardless of thicknesses. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1365–1372     

Effect of temperature and solvent on the structure and transport of a tethered membrane: Monte Carlo simulation

An extended bond-fluctuation model, introduced previously to study the conformation and dynamics of a self-avoiding sheet (SAS), is further used to understand the temperature dependence on the conformation and dynamics of a tethered membrane (i.e., nodes tethered by fluctuating bonds with excluded volume constraints) in an effective solvent media on a cubic lattice by Monte Carlo simulations. The node–node (nn) and node–solvent (ns) interactions and temperature orchestrate the stochastic motion of each membrane node, and therefore describe the morphology of the membrane. With increasing temperature, the radius of gyration (R_g) of the membrane decreases with repulsive node–node interactions in an attractive solvent medium (ns < 0). The inverse effect is seen in a repulsive medium. Changes in the membrane's R_g show that the membrane contracts (stretches) with the range of attractive (repulsive) node–node interaction with more pronounced effects on lowering the temperature. The variations of R_g with T, which are affected by wrinkles and crumpling, are complex (with the possibility of stretched exponential functions) depending on the type of membrane, quality of the solvent, and the temperature. Likewise, the segmental dynamics exhibits a range of power-laws, different from that of a SAS, while the global membrane reaches its asymptotic diffusive behavior. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3478–3486, 2005     

Phase behavior study of poly(N‐tertbutylacrylamide‐co‐acrylamide) in the mixture of water–methanol: The role of polymer–nonsolvent second‐order interactions

The phase behavior of poly(N‐tertbutylacrylamide‐co‐acrylamide) (PNTBAM) in pure water and mixture of water–methanol is studied at different temperatures. The different compositions of PNTBAM are prepared by free‐radical polymerization technique and their phase behavior is studied by turbidimetry. The effects of copolymer and solvent composition on the phase behavior of the copolymers are discussed. It has been suggested that the inhomogenities in polymer chains are responsible for lowering the rate of phase transition by increasing the N‐tertbutylacrylamide (NTBAM) and methanol contents in copolymer and mixture, respectively. For the first time we have revealed that there are second‐order binary interactions in the water–methanol which are dominant in the special range of copolymer composition. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 455–462, 2009     

Poly(3‐hexylthiophene) aggregate formation in binary solvent mixtures: An excitonic coupling analysis

The aggregation behavior of P3HT [M_n ≈ 28.2 kDa, regioregularity >96%, PDI ≈ 1.3] in 96 solvent mixtures is studied using UV–vis absorption spectroscopy. Hansen solubility parameters and Spano excitonic coupling analyses are used to identify correlations between the properties of the solvent mixtures and the extent of structural order of the aggregates. It is clear that the identity of the poor solvent used to drive aggregation has a significant impact on the excitonic coupling behavior and, hence, the structural order of the P3HT aggregates. However, solubility parameter theory does not account nor provide a predictive theory for the observed trends. Instead, qualitative arguments based on the nature of the interactions between the solvents and the polythiophene and hexyl side chain motifs are used to rationalize the kinetics of formation and the observed excitonic coupling characteristics of the P3HT aggregates. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 526–538     

Annealing effect on performance and morphology of photovoltaic devices based on poly(3‐hexylthiophene)‐b‐poly(ethylene oxide)

Novel block copolymers, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) (P3HT‐b‐PEO) were synthesized via Suzuki coupling reaction of P3HT and PEO homopolymers. The copolymers were characterized by NMR, gel permeation chromatography, differential scanning calorimeter, and UV–vis measurements. A series of devices based on the block copolymers with a fullerene derivative were evaluated after thermal or solvent annealing. The device using P3HT‐b‐PEO showed higher efficiency than using P3HT blend after thermal annealing. Phase‐separated structures in the thin films of block copolymer blends were investigated by atomic force microscopy to clarify the relationship between morphologies constructed by annealing and the device performance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The coalescence of polystyrene in correlated binary solvents

The solution behavior of solvophobic polymers is crucial to the development of polymer coatings and polymeric drug delivery vehicles. In this article, the role of dipolar interactions is investigated in the solvophobic coalescence of polystyrene in binary correlated polar solvent mixtures. A simple model for coalescence thermodynamics is derived from correlations between thermally rotating dipole moments in the solvent. The stabilizing correlations lost to the solvent due to a solute's presence give rise to a driving force for the coalescence of solutes. This stabilization is offset by the entropy of mixing that favors the dispersion of solutes. Predictions are compared to the measured point of coalescence of polystyrene in acetone when different alcohols are titrated. The model is shown to capture this point of coalescence and conformation for a variety of systems. Our results suggest the significant property determining the solubility of nonpolar polymers in a polar liquid is a free energy resulting from attractive dispersion interactions between thermally rotating solvent dipole moments. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 948–955     

A facile approach to fabricate hierarchically structured poly(3‐hexylthiophene‐2,5‐diyl) films

Microstructured surfaces have great potentials to improve the performances and efficiency of optoelectronic devices. In this work, a simple robust approach based on surface instabilities was presented to fabricate poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) films with ridge‐like/wrinkled composite microstructures. Namely, the hierarchically patterned films were prepared by spin coating the P3HT/tetrahydrofuran (THF) solution on a polydimethylsiloxane (PDMS) substrate to form stable ridge‐like structures, followed by solvent vapor swelling to create surface wrinkles with the orientation guided by the ridge‐like structures. During spin coating of the P3HT/THF solution, the ridge‐like structures were generated by the in‐situ template of the THF swelling‐induced creasing structures on the PDMS substrate. To our knowledge, it is the first report that the creasing structures are used as a recoverable template for patterning films. The crease‐templated ridge‐like structures were well modulated by the THF swelling time, the modulus of the PDMS substrate, the P3HT/THF solution concentration and the selective/blanket exposure of the PDMS substrate to O₂ plasma. UV–vis and fluorescence spectrometry measurements indicated that the light absorption and fluorescent emission were improved on the hierarchically patterned P3HT films, which can be utilized to enhance the efficiencies of organic solar cells. Furthermore, this simple versatile method based on the solvent swelling‐induced crease as the in‐situ recoverable template has been extended to pattern other spin‐coated films with different compositions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 928–939     

Luminescence of monolayer thin films of the fully conjugated rigid‐rod polymer poly(p‐phenylenebenzobisthiazole)

Poly(p‐phenylenebenzobisthiazole) (PBT) is a heterocyclic, aromatic rigid‐rod polymer with a fully conjugated backbone and excellent dimensional, thermo‐oxidative, and solvent stabilities. A PBT polymer with an intrinsic viscosity of 18.0 dL/g was dissolved in methanesulfonic acid or Lewis acid. The PBT solution was spin‐coated and doctor‐bladed for freestanding films or onto an indium tin oxide (ITO) substrate. The acid was removed via coagulation. Scanning electron microscopy determined that the resultant film thicknesses were about 340 and 60 nm for PBT freestanding films and films on the ITO substrate, respectively. X‐ray scattering demonstrated that the freestanding films were in‐plane isotropic without long‐range order. The freestanding films were excited with a He‐Cd laser at 325 nm for photoluminescence (PL) response. PL spectra showed a distinct intensity maximum at 580 nm, regardless of the film‐forming conditions. After the films cooled to 67 K, the PL maximum shifted to 566 nm with enhanced intensity. Aluminum was evaporated onto the monolayer PBT thin film on the ITO substrate as an electron injector for electroluminescence (EL) response. Diodic electric behavior was observed for all monolayer PBT EL devices for the first time. A threshold voltage as low as 4 V was achieved for the monolayer EL devices. In addition, PBT EL spectra were tunable, with a maximum intensity at 570 nm at a bias voltage of 4.5 V changing to 496 nm at 7.5 V (i.e., a blueshift) with greatly increased intensity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1760–1767, 2002     

Solution characterization of the novel organometallic polymer poly(ferrocenyldimethylsilane)

A series of four well‐defined poly(ferrocenyldimethylsilane) (PFS) samples spanning a molecular weight range of approximately 10,000–100,000 g mol⁻¹ was synthesized by the living anionic polymerization of dimethyl[1]silaferrocenophane initiated with n‐BuLi. The polymers possessed narrow polydispersities and were used to characterize the solution behavior of PFS in tetrahydrofuran (THF). The weight‐average molecular weights (M_w ) of the polymers were determined by low‐angle laser light scattering (LALLS), conventional gel permeation chromatography (GPC), and GPC equipped with a triple detector (refractive index, light scattering, and viscosity). The molecular weight calculated by conventional GPC, with polystyrene standards, underestimated the true value in comparison with LALLS and GPC with the triple detection system. The Mark–Houwink parameter a for PFS in THF was 0.62 (k = 2.5 × 10⁻⁴), which is indicative of fairly marginal polymer–solvent interactions. The scaling exponent between the radius of gyration and M_w was 0.54, also consistent with marginal polymer–solvent interactions for PFS in THF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3032–3041, 2000     

Environmentally Stable Polymer Gels with Super Deformability and High Recoverability Enhanced by Sub‐5 nm Particles in the Nonvolatile Solvent

It remains challenging to satisfy the combined performances for hydrogels with excellent mechanical behavior, high deformability, and super recoverability under harsh environmental conditions. In this study, we first established a strong polymer network via the crosslinking of polymer chains on the surfaces of sub‐5‐nm calcium hydroxide nanospherulites in ethylene glycol solvent. The organic gel expressed excellent mechanical properties such as a recoverable compressive engineering stress of 249 MPa and an elongation stress of 402 KPa, which was attributed to the uniform nanosized crosslinking structure as characterized by SEM. Moreover, the nonvolatile solvent remained in the gel, meaning that the sample can resist a wide temperature range of ?56 to 100 °C without losing the elastic properties. This novel organic gel could provide promising routes to develop the ideal elastic carriers for wearable devices, smart skin sensors, and damping materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 713–721     

Synthesis and characterization of a starch‐modified hydrogel as potential carrier for drug delivery system

Synthesis and characterization of a new hydrogel were carried out using a chemically modified starch (starch‐M) consisting of coupling C?C bounds coming from glycidil methacrylate (GMA) onto the polysaccharide structure. ¹³C NMR, ¹H NMR, and FT‐IR spectroscopies were used to confirm the incorporation of such groups onto the starch‐M. The hydrogel was prepared by a crosslinking polymerization of starch‐M using sodium persulfate as an initiating agent. The starch‐M hydrogel shows morphology clearly different from that of the raw starch film due to the presence of voids on its surface. The swelling process of the starch‐M hydrogel was not significantly affected by changes on the temperature or on pH of the surrounding liquid, indicating the such behavior can be then understood by a diffusional process, resulting from its physical–chemical interactions with the solvent. The values of the diffusional exponent n were on the order of 0.45–0.49 for the range of pHs investigated, demonstrating that the water transport mechanism of starch‐M hydrogel is more dependent on Fickian diffusion, that is, controlled by water diffusion. Such starch‐M hydrogel is a promising candidate to be used in transporting and in preserving acid‐responsive drugs, such as corticoids, for the treatment of colon‐specific diseases, for example, Crohn's disease. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2567–2574, 2008     

The role of material behavior in the performances of electroactive polymer energy harvesters

Electroactive polymer energy harvesters are promising devices for the conversion of mechanical work to electrical energy. The performances of these devices are strongly dependent on the mechanical response of the polymeric material and on the type of electromechanical cycle, and these are limited by the occurrence of dielectric breakdown, compression induced wrinkling and electromechanical instability (pull‐in). To identify the optimal electromechanical cycle that complies with all of these limitations, we set‐up and solve a constraint optimization problem and we critically discuss the influence of material behavior of the polymer in the optimal performances of the energy harvesting device. Finally, we show that if the rate‐independent dissipative behavior of the polymer (Mullins effect) is neglected, the optimization procedure may lead to quite unsatisfactory predictions: by making reference to explicit experimental data from literature we show that an optimal harvesting cycle deduced by neglecting the Mullins effect is far from being optimal when this is taken in consideration. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1303–1314     

Tuning the energy gap of conjugated polymer zwitterions for efficient interlayers and solar cells

Narrow band gap conjugated polymer zwitterions (CPZs) were synthesized by Suzuki polymerization and characterized to understand their electronic properties and utility as cathode modification layers in solar cells. The polymers were prepared from diketopyrrolopyrrole (DPP) and iso-indigo monomers containing sulfobetaine (SB) pendant groups, benefiting from an ion-rich aqueous phase in the polymerizations. UV–vis absorption spectroscopy revealed the optical energy gap value for the CPZs, ranging from 1.7 to 1.2 eV. Ultraviolet photoelectron spectroscopy of the CPZs as thin layers on Ag metal showed that the pendent zwitterions impart an interfacial dipole (Δ) to the metal and a work function reduction of ∼0.9 eV. OPVs fabricated using a conventional bulk heterojunction (BHJ) device architecture of ITO/PEDOT:PSS/(PTB7:PC₇₁BM)/CPZ/Ag led to dramatic improvements in power conversion efficiency (PCE) values relative to devices having bare Ag cathodes (PCE < 2% for bare Ag vs. 6.7–7.7% for CPZ/Ag). The benzothiadiazole (BT)/DPP polymer denoted as PT₂BTDPPSB gave an optimal PCE of 7.7% in a conventional BHJ OPV device architecture fabricated on a Ag cathode. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 327–336     

Physically cross‐linked networks of POSS‐capped poly(acrylate amide)s: Synthesis,morphologies, and shape memory behavior

In this work, we synthesized a novel organic–inorganic semitelechelic polymer from polyhedral oligomeric silsesquioxane (POSS) and poly(acrylate amide) (PAA) via reversible addition‐fragmentation chain transfer (RAFT) polymerization. The organic–inorganic semitelechelic polymers have been characterized by means of nuclear magnetic resonance spectroscopy, thermal gravimetric analysis, and dynamic mechanical thermal analysis. It was found that capping POSS groups to the single ends of PAA chains caused a series of significant changes in the morphologies and thermomechanical properties of the polymer. The organic–inorganic semitelechelics were microphase‐separated; the POSS microdomains were formed via the POSS–POSS interactions. In a selective solvent (e.g., methanol), the organic–inorganic semitelechelics can be self‐assembled into the micelle‐like nanoobjects. Compared to plain PAA, the POSS‐capped PAAs significantly displayed improved surface hydrophobicity as evidenced by the measurements of static contact angles and surface atomic force microscopy. More importantly, the organic–inorganic semitelechelics displayed typical shape memory properties, which was in marked contrast to plain PAA. The shape memory behavior is attributable to the formation of the physically cross‐linked networks from the combination of the POSS–POSS interactions with the intermolecular hydrogen‐bonding interactions in the organic–inorganic semitelechelics. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 587–600